Search Documents

By L. Dison

This technical note is issued in two parts, as follows: Part I, after a brief introduction, discusses the value of patents and the law of patents, including patent applications and the exploitation of inventions. This is followed by some comments for the benefit of would-be inventors and potential users of patents. Part II, which will appear in the February issue of this Journal, focuses on the mining industry and then discusses views on patents that were Quoted in Part I. The last section makes recommendations as to how II1ventors and users (including mining authorities) should handle patents.

Jan 1, 1992

By H. Möller, L. Mashigo, C. Gassmann

Wire-arc additive manufacturing (WAAM) is a directed-energy deposition technology that uses arc welding procedures to produce computer-aided designed parts, such as three-dimensional printed metal components. A challenge of additive manufacturing is the anisotropy. Interstitial elements play a significant role in the mechanical properties of Ti6Al4V of different grades. In this research, the mechanical properties of Grade 5 and Grade 23 Ti6Al4V were compared for this application. Samples were extracted from WAAM-produced Ti6Al4V walls in different directions (horizontal and vertical) and at different positions (top and bottom). The samples were subjected to optical microscopy and tensile and hardness tests. Grade 5 Ti6Al4V samples were found to have greater strength, greater hardness, and lower ductility, owing to the higher content of interstitial elements compared with Grade 23. The bottom samples had higher strength than the top samples, which is attributed to thermal cycling during manufacturing, resulting in different microstructures.

Jul 1, 2021

By A. G. Ramsay, P. G. Kahles, L. E. Kun

A method for the clarification of uranium pregnant solutions using a high-rate floc blanket was developed from laboratory scale through pilot-plant testing to full-scale production by the Anglo American Research laboratories. A two-stage clarification process (hopper plus leaf) was commissioned at the Western Deep levels uranium plant in October 1980. The high efficiency of the hopper clarification permitted its use on its own. The leaf clarifiers were therefore taken out of service in September 1981, since when the secondary clarification is achieved by further unaided gravity settling in the semi-clarified and clarified pregnant-solution storage tanks. As a result, a daily 12000 to 17000 t of countercurrent-decantation overflow with a suspended-solids concentration of 500 to 600 mg/I is continuously clarified to a suspended-solids concentration of less than 30 mg/I. Secondary gravity settling reduces the suspendedsolids concentration to under 20 mg/I. The cost of the single-stage hopper-clarification process is RO,O020per ton of liquid treated. The removal of the leaf clarifiers from the circuit resulted in an approximate visible saving of RI00000 per annum.

Jan 1, 1983

By D. Das, B. K. Nandi

The present study focuses on utilising the electrocoagulation (EC) process for the treatment of process water generated in an iron ore beneficiation plant for safe discharge and reuse. Removal of heavy metals like Fe, Cr, Cu, Zn, Mn and Pb which was found in higher concentration along with some other impurities exceeding the permissible and discharge limit were attempted. The influence of different electrode material, current density, inter-electrode distance, and solution conductivity was explored for effective removal of the metal ions. Experimental results infer that almost 99.95% Fe, 97.77% Cr, 73.44% Cu, 99.34% Pb and 88.69% Mn was removed using aluminum electrodes at monopolar mode at a current density of 68.50 A/m2, inter-electrode distance of 1 cm and solution conductivity of 1.033mS after 60 min of EC. In addition, removal of other toxins like TDS, turbidity, salinity and conductivity etc. was also assessed during the process. Removal of such heavy metal ions by EC was found to follow 1st order kinetics with electric energy consumption of 3.93 kWh/m3, electrode consumption of 0.1191 kg/m3 and operating cost of 0.6115 US$/m3 respectively. Keywords: Fe removal, electrocoagulation, Al electrode, turbidity

Jan 1, 2020

By R. C. J. Goode, W. S. Rapson, W. R. Lawrie, L. W. P. Van Der Bosch

W. R. Lawrie (Member): As all the Institute members present are aware, the Ninth Commonwealth Mining and Metallurgical Congress was held in Great Britain from 3rd to 24th May, 1969. The Congress opened in London and the first week was devoted to technical sessions. Several receptions and other forms of entertainment were held in the evenings. The Congress was attended by some 1 200 delegates, many of whom were accompanied by their wives. As can be imagined a large organisation was needed to cater for all the whims of these delegates, to arrange accommodation and to provide transport for the technical trips, for the receptions and for the sight-seeing tours. Papers presented at the technical sessions proved of great interest. It was stimulating to hear of the developments taking place in the various branches of mining and metallurgy. The discussions which developed between men from so many different countries were thought provoking, led to new friendships and most of us made valuable contacts for the future. There were 141 papers presented in the one week. They were given in four separate halls with two, three and sometimes four papers coming up for discussion in each of the three sessions per day in each hall. Among the more interesting subjects were those concerning off-shore drilling and the facilities for production of petroleum and natural gas. Beach mining at Consolidated Diamond Mines drew a large audience. Automation, mechanization and other technical developments were well described and we were brought up to date with modern techniques of mineral prospecting. There was general discussion on the future of the mineral industries together with comments on the consumption and price trends of these metals and minerals. The future of uranium, of vital interest to us in South Africa, came in for much debate. During the first week, besides attending the technical sessions and seeing some of the sights of London, we were royally entertained. There was a banquet, attended by some I 400 people, where we were welcomed by Princess Alexandra, a reception by H.M. Government in the Banqueting House, and we were entertained at the House of Lords on a terrace overlooking the bustling and rather muddy river Thames. Then there was the visit to the Glyndebourne Opera. It is only in London that at 3 o'clock of an afternoon, nearly 1 000 people all togged up in dress suits and long dresses and carrying packets of sandwiches for supper could arrive at a station to catch a train, and not even cause a stir of interest or a raised eyebrow! This is the way we travelled 60 miles to the opera from London. Surely there can be no more picturesque or romantic a setting for an opera than this large 400-year old red brick manor house nestling in the green valleys of the unspoilt Sussex countryside. It was a glorious evening and though we returned somewhat late and tired, not one of us would have missed this experience. After the first week in London there was a choice of tours of one week to London and the Home Counties, Cornwall, a Geological tour to Scotland, South Wales, and North England. These were followed by further one week tours to Yorkshire and Lancashire, Scotland, West Country and Midlands, a Geological tour of Wales, and a Mining and Geological tour to Jurassic Iron Mines. We then returned to London for the final session and closing banquet. Post-congress tours were arranged to Europe and to Ireland. It was a wonderful Congress, a great experience, we made many friends and may there be many more congresses! . L. W. P. van den Bosch (Member): Much has already been said in appreciation of the excellent organisation and arrangements made for the delegates who attended this Congress. This report is confined to a brief discussion of the personal impressions gained from the papers presented and the technical visits attended. The papers covered a wide variety of subjects ranging from highly theoretical observations to practical descriptions of operations. There were three main themes, VIZ: 1. The attention given to research and its forceful application to practical operation. 2. A steady development in mechanization and automation leading to savings in manpower. 3. Improvization, modernization and adaptation of exisitng facilities. Thoughts on these themes can best be illustrated by comments on some of the industries visited. COAL The National Coal Board (N.C.B.) has been most progressive and all of us have heard of the Bevercotes Colliery with its completely automatic mining and coal handling equipment. This was not, unfortunately, on show but there is no doubt that this is one of the greatest advances in coal mining leading towards continuous production. Coal in Britain is fighting for its life against oil, North Sea gas, imported gases and nuclear power. Output is dropping, the less efficient collieries are closing down and efficiencies are steadily rising as the following tabulation indicates: In 1931: 1 million men produced 300 million tons of coal In 1947: 0.7 million men produced 230 million tons of coal In 1968: 0.4 million men produced 160 million tons of coal

By V. C. Robinson

INTRODUCTION Most presidential addresses are in the nature of a review of some specific topic and this will be no different. In thinking about the subjects which might be suitable for this address I decided that as next month will see my retirement from the gold mining industry I might review the four decades since I started in the industry in 1929. These four decades have been more than usually in',~resting and exciting. They have covered a period when the price of gold increased from the old figure of 84/- an ounce to the price of $35 an ounce today, taking in on the way at least two periods of premium sales from which the producer benefitted. The industry in these four decades has survived the most totally destructive war in history and has seen fundamental changes in the political, economic and governmental life of South Africa. There have been great technological changes and improvements, some of which I shall refer to later, and in addition there have been profound changes in the relations between employer and employee in the industry which have affected not only the economy of the industry but the traditional thinking of both management and labour. I believe that the address presented to this Institute on the occasion of its 75th Anniversary by Mr Goode covered more than adequately the history of the Institute and the part it has played in the mining industry of South Africa. It would be merely repetitive, therefore, to discuss the affairs of the Institute of Mining and Metallurgy. Having said this, however, it is also necessary to point out that the history of the Institute is, and always will be, an important record of the history of mining in South Africa. There are many facets, however, on which we ought to look back and to re-examine. One of the most rewarding, but at the same time one of the dullest, places to look for historical facts is in the annual reports of the Chamber of Mines. I suppose that some of the dullest of these have been the reports for which paragraphs have been prepared by me personally. The notes which follow do not claim to be anything like a full record of this exciting period. RISE AND FALL OF THE GOLD MINING INDUSTRY In talking about the mining industry of South Africa it is inevitable that one talks, particularly in the historical sense, about the gold mining industry - an industry of fundamental importance which has made South Africa what it is and which has been dying since the early part of this century. In Table I is shown the progress of the gold mining industry measured by its output of ounces of fine gold from the beginning of operations until the end of 1969, and if you are interested in the productivity of the men who work this industry the table, composed entirely from figures set out in the Chamber's annual reports, also shows the production of gold expressed as fine ounces per European and fine ounces per Bantu worker over a long period. If you are still minded to think of this industry as dying then the last column in the table shows how uranium has played such a vital part in the prosperity of the country.

By H. C. Voges

The concentration of cassiterite at Iscor's Uis Mine is described, and information is given on aspects of the concentration of iron ore at Thabazimbi and Sishen Mines. At Uis, a very Iow-grade tin ore is concentrated by three-stage jigging, spiral concentration, and tabling to give a high-grade concentrate with a recovery of 80 per cent of the tin. A Iow-grade tantalite-columbite concentrate is also produced. The possibility of recovering mica, the use of sluice boxes instead of spirals, and the recovery of cassiterite from minus 45 µm material are being investigated. At the two iron-ore mines, heavy-medium separation is applied to size fractions larger than 0,5 mm. The types of ferrosilicon and the circuits used for the recovery of ferrosilicon from the various dilute-medium circuits are described. The spiral-concentration plant being installed at Thabazimbi for the treatment of the minus 0,5 mm portion of the ore is described.

Jan 1, 1982

By Doris Gardner

On Friday, 6th June, 1986, an SAIMM party of32 set out at 06h30 for a tour of Duvha Opencast Colliery, Lesedi Village, and Duvha Power Station-all situated just outside Witbank. Duvha Colliery On arrival at the mine, the party was met by Mr. Colin Kolver, Assistant General Manager, and the guides for the morning. After refreshments had been served, Mr. MacDonald, General Manager, welcomed the tour, and a series of slides on the opencast mine and Lesedi Village were shown.

Jan 1, 1986

Discussion of the previous paper E. N. H. MOLLOY The first 22-foot-diameter Aerofall mill was installed at Mangula in 1957. This was fitted with cast-iron trunnion'! located to the mill shell with 2-inch-diameter mild-steel bolts. O.F .S. Branch Minutes of the General Meeting held at the Welkom Club on Wednesday, 2nd June, 1976, at 4.00 p.m. Mr G. J. C. Young (Chairman of the O.F.S. Branch) was in the Chair. Also present were:

Jan 9, 1976

By X. Yang, G. D. Zhai

The prop is the most important part to ensure the proper functioning of hydraulic support. When the hydraulic support is impacted by the roof, the prop is prone to extrusion deformation, expansion, and even bursting. In order to study the stress on a doubly-telescopic hydraulic support prop under impact load, an impact simulation was carried out based on the drop weight method. First, the impact model of the hydraulic system of the prop was established in AMESim software and the dynamic response curves of the bottom and middle cylinder of the prop obtained. Then, according to the conservation of energy, the pressure formulaes in the hydraulic cylinder of the prop under impact load were derived and verified by the AMESim simulation results, and the maximum pressure on the inner surface of the hydraulic cylinder of the prop obtained. Lastly, the transient dynamic simulation of a hydraulic support prop was carried out in ANSYS Workbench software, and cloud diagrams of stress and deformation of the prop obtained using Workbench simulation. The AMESim simulation process describes the change in fluid pressure in the prop, and the pressure formulae can be used to estimate the internal pressure of the prop under impact load. The finite element analysis results show that the stress of the middle hydraulic cylinder is much greater than that on the bottom hydraulic cylinder under impact load, which can provide a reference for prop design.

Jul 2, 2022

By L. Zhou, J. Qiu, M. Tang, J. Wang, G. Dai

Coal spontaneous combustion in longwall gobs is a major concern in coal mines. In comparison to other hazards, this phenomenon is difficult to detect. Fifteen factors influencing coal spontaneous combustion in longwall gobs were identified from the literature. The logical relationships between these factors were evaluated and quantified by decision-making trial and evaluation laboratory (DEMATEL) and interpretive structural modelling (ISM) methods. A four-level hierarchical structure model was established. The research shows that combining DEMATEL and ISM can reveal the key factors that influence coal spontaneous combustion in longwall gobs and establishthe interactions and relationships among these factors. The results can provide the basis for preventing and controlling coal spontaneous combustion in longwall gobs.

Jun 10, 2024

By J. Cilliers, R. Seitz, D. Drinkwater

Mineral processing produces a saleable product from high-cost ore. The Mineral Processing Engineer must constantly improve the separation to create the most value from the ore and reduce the associated costs. Graduate Metallurgists (or Chemical Engineers) have had the university theoretical training required, but often are illprepared to perform their plant roles. The in-work Metcelerate programme was designed specifically to develop the practical skills that Mineral Process Engineers require, by combining three key elements: 1. Knowledge transfer through self-paced, on-line training; 2. Practical skills acquisition through assessed, practical plant exercises; 3. Skills development through online tutorials. A final process improvement project adds significant value to the operation that far exceeds the training cost. Experience from Metcelerate clients has indicated improved staff retention, greater confidence, and pro-active process intervention.

Jan 1, 2023

By C. B. van den Berg

n this study, silver and palladium nanoparticulate inks with different metal-binder ratios were screen-printed onto a paper substrate. The printed layers comprised the metal nanoparticles and an ethylcellulose binder. The layers are not typical metal composites due to the low concentration of binder and high porosity. The electrical sheet resistivity of each particle concentration was measured, and the data fitted using the scaling law of percolation theory and the general effective media (GEM) equation. The percolation parameters, i.e. the percolation threshold and the critical exponent, for each system were determined from the fits and compared. The percolation threshold for the palladium layer (39.8 wt%) was lower than that found for the silver layer (44.9 wt%). The critical exponents determined for the palladium and silver layers were both lower than the universal value for three-dimensional percolation systems. Microscopy observations indicate that the difference in the percolation threshold for the two layers can be attributed to variations in their microstructure.

Jan 1, 2014

By A. J. S. Spearing, M. Sharifzadeh, K. V. Jessu

Empirical pillar design methods are commonly used in the mining industry. The parameters within which these methods are valid are frequently unknown to the user or ignored. In addition, empirical design may not consider essential parameters such as blasting effects, orebody dip and the presence of geological structures, which all adversely affect the stability of the pillars. This can result in potentially serious pillar design strength over-estimates. Although the commonly based tributary area method is generally conservative, as the spans are seldom that large relative to the depth, failing to consider other relevant parameters can result in errors. Problems associated with an under-designed pillar can range from a local pillar collapse to a catastrophic chain reaction collapse (or run). Over-designed pillars are generally safe but reduce the extraction of the orebody, thus adversely affecting the profitability of the mining operation. We used laboratory tests and numerical modelling to understand the effects of pillar orientation, blasting and the presence of discontinuities on pillar strength. Reduction factors were developed with these models to be implemented in conjunction with the existing empirical pillar design methods. For any pillar or mine design, once it is implemented, the actual performance of the system must be checked regularly by observation and monitoring and adjusted if needed. The pillar design approach outlined in this paper can better optimize the pillar mining method by considering other generally ignored but important parameters, thus improving safety, productivity, and economic aspects.

Oct 1, 2022

By E. J. Y., G. J. McLachlan, E. Amini, Koha

Inferring individual component flotation rates from recovery-time data of ore complexes is important in optimising and designing minerals processing plants. However, existing two-component first-order flotation models are computationally intensive to solve using conventional non-linear least squares regression. In this paper, a Convolutional Neural Network (CNN) is used to approximate the inverse function which predicts the two-component first-order model parameters using recovery-time data. This paper compares the accuracy and computation speed of the proposed CNN against traditional non-linear least squares regression on 1 million generated data based on a known two-component firstorder kinetic model. It is shown that using a CNN is possible to approximate the inverse function for the non-invertible two-component model with recovery-time as an input matrix for convolution operations. The CNN method is 450 times faster to compute than the Trust-Region (TR) non-linear least squares regression algorithm. However, the CNN model is less accurate compared to the TR algorithm overall. Keywords: Flotation kinetics, convolutional neural network, inverse problem, modelling and simulations

Jan 1, 2020

By E. Saari, B. Musuku, K. Jansson

The quality of the concentrator plant process water is crucial for high performing mineral flotation circuits. Significant metal recovery and concentrate grade losses have been noticed particularly in more closed water loops. The recovery and quality losses have started to emerge mainly with decreased freshwater usage and because of changes in tailings management towards tailings thickening, paste, or dry stacking. These changes result in shorter, closed water loops with a rapid build-up of harmful components with negative impact on the beneficiation process. Consequently, water quality has a direct link to decreased product value and sales returns. Complete cleaning or water blending might not be the right way to achieve high recovery and high-quality products. Instead, the key is to understand what kind of water qualities are needed for the flotation of specific minerals. In this study harmful substances in various plant water streams were removed and/or modified by pilot-scale dissolved air flotation. Batch-scale mineral flotation tests with the untreated and treated water were then performed by using fresh ore samples and the plant’s own laboratory flotation procedure. The results indicate that because of dissolved air flotation, the mineral flotation recoveries were enhanced by 1‒3.3%. Keywords: Mineral recovery, metal recovery, mineral quality, process water, concentrator, beneficiation, mineral processing, flotation, process water treatment

Jan 1, 2020

By R. o. Cretier, L. A. Cisternas, A. López-Valdivieso, F. Valdes, E. Gálvez, G. Gahona

The size of the particle plays an important role in the flotation of minerals. Comminution allows the release of valuable species and their subsequent recovery. Then, the degree of concentration and recovery will depend on the size of the particle. In this work, we investigated the flotation of coarse particles (-850 +150 μm) of copper ores when using the fluidized-bed separator (HydroFloat® cell) and compared it with the process of conventional flotation with medium size particle (-150 μm) (Metso cell) using seawater. The collector concentration was the main variable studied in terms of copper recovery. The results show that the flotation of coarse particles is feasible using seawater without frother

Jan 1, 2020

By V. K. Risinggård, M. Sparta

We report on the development of a finite-element method model for a pilot furnace for the production of manganese alloys. The model is a multiphysics model that addresses material flow, electrical conditions, heat transfer, and physical and chemical transformations. It is capable of studying both quasi-steady and transient states in time-dependent simulations. The model includes common charge materials and fluxes and can simulate production of both ferromanganese and silicomanganese alloys with acid and basic slags, as well as changing charge compositions. The model output provides access to the material distribution in the furnace during furnace runs, temperature profiles, current paths, energy balances, and alloy and slag production rates and compositions.

Apr 16, 2024

By A. S. Geldenhuys, L. S. Leal Filho, D. A. Deglon, T. C. Souza Pinto

The Brucutu iron ore mine (Minas Gerais, Brazil), is Vale`s largest iron producing operation achieving around 21 million tons by flotation of iron ore pellet feed per annum. The run of mine is mainly composed of hematite (70%) and quartz (30%). After preparation (comminution and sizing), the slurry is submitted to reverse cationic flotation of quartz under basic conditions (pH=10.5). Corn starch (500g/t) is used to depress Fe-bearing minerals and alkyl (C10) ether amine is the collector for quartz. The flotation circuit is arranged in a “coarse” section utilizing dated 28m3 square Wemco cells, and a “fine” section utilizing modern 160m3 tank cells. The “coarse” flotation circuit treats material from the deslime cyclone underflow while the “fine” circuit treats material from the deslime cyclone overflow and the pulp product from the “coarse” circuit scavenger 2 bank. Evaluation of process performance is of high importance as even small gains can lead to large improvements for this high throughput plant. Cell-by-cell samples of the froth products, selected feed and pulp-products were analyzed for flow-rate, overall chemical composition, and particle size distribution. Bank-by-bank samples of the feed, froth and pulp products were analyzed on an assay-by-size basis. In addition, the flotation cells were hydrodynamically characterized and gas dispersion parameters assessed. The detailed experimental program resulted in a thorough characterization of the process and enough information to produce a calibrated floatability component model. Longer mainline residence time results in significant Fe2O3 losses while yielding little benefit in terms of SiO2 grade. Scavenger 2 has twice the residence time of scavenger 1 while having to treat only 10% of the SiO2; resulting in high Fe2O3 recoveries to the froth and poor separation. In addition, it is shown that the Fe2O3 exhibits true flotation behavior resulting in increased Fe2O3 losses. The detailed data collection campaign coupled with in depth data analysis and modelling gives unprecedented information and highlights avenues for optimization that was previously unknown. Keywords: Froth Flotation, Process modelling, Process evaluation, Metallurgical survey

Jan 1, 2020

By T. Bhambhani, J. Jankolovits

Sphalerite flotation using copper sulfate has been performed in the industry for decades and the mechanism of Cu activation is well established. Despite its ubiquity, many practical questions surrounding copper sulfate persist. It is not clear how iron selectivity is achieved in zinc circuits given the propensity of iron sulfides to be activated by copper. Also, the large variation in copper sulfate dosages across different plants and ore types cannot be explained. Lastly, Zn flotation with greatly reduced copper sulfate dosages attracts significant interest and has been demonstrated in certain laboratory settings, but no information is available on why those laboratory solutions have not been adopted in plant practice. Flotation studies are presented that demonstrate that Zn flotation with very low copper sulfate dosages is possible when using certain novel collectors that are not practised in the industry. However, these reagent schemes are impractical because of a heretofore unappreciated and critical role that copper sulfate plays in Fe rejection. With both very low and standard copper sulfate dosages, copper sulfate influences both Zn flotation and Fe rejection. The results highlight the multifaceted role of copper sulfate in zinc flotation and the need to holistically consider complex systems’ behaviour to understand flotation reagent mechanisms and optimise plant performance. Keywords: Sphalerite flotation, metal activation, copper sulfate, iron rejection

Jan 1, 2020