Search Documents

By C. M. McKinney

The Bureau of Mines analyzed 626 crude oils from 546 oilfields in the United States that produced 2,500 BOPD or more during at least 1 of the last 3 years. Included also are crude oil analyses from eight fields that produced less but which were located in areas having few or no fields that produced 2,500 BOPD. The tables show the geographical and geological source, general characteristics. and determined and computed analytical data for each sample. The analyses were made according to the Bureau of Mines routine method and are directly comparable to other previously published analyses.

Jan 1, 1966

By J. M. Davidson, F. Fraas, J. E. Conley

"A number of Reports of Investigations pertaining to the extraction of potash from cal¬cined polyhalite have been made by various members of the Nonmetallic Minerals Experiment Station of the United States Bureau of Mines. These reports describe results obtained in the study of samples of polyhalite (2CaS04.K2S04.MgS04.2H20) from deposits of possible com¬mercial importance in Texas and New Mexico.3Storch and Clarke6 in their initial paper presenting data on the properties of Texas polyhalite demonstrated the desirability of calcination and subsequent hot extraction with water as a satisfactory pronedure for treatment of this potash-bearing salt. Their preliminary data have been supplemented by an additional report7 dealing more particularly with the leaching of raw and calcined polyhalite with water and with saturated sodium chloride solu¬tions. Further data8 have been reported as a result of experiments made in a small labora¬tory rotary-tube furnace under various calcination and extraction conditions. Hot water was used as the leaching solution in all of these tests.In addition to the data on calcination and extraction, two processes as proposed by Storch and Clarke have been published by Wroth,9 and more recently a number of very promising processes have been proposed by Storoh and Fragen.10"

Apr 1, 1932

By L. O. Bacon, H. R. Joesting, J. H. Getz

"INTRODUCTION For a number of years manganiferous iron ore has been mined on a small scale at Boston Hill, in Grant County, N. Mex. Total production up to 1943 is estimated to be over 793,000 long tons, containing 8 to 35 percent manganese and 26 to 46 percent iron. 4/ During 1941 to 1943 production was estimated to be 206,000 long tons, containing about 13 percent manganese and 37 percent iron. During 1944 daily production was several hundred tons, mostly from a single open pit. Several moderately large deposits have been mined: and many smaller ones have been found.From February to April 1945 geophysical surveys were carried out on Boston Hill by the Division of Geophysical Exploration, in cooperation with District 5, Central Region, Bureau of Mines, to determine if hitherto undiscovered manganiferous iron deposits exist. Field work was interrupted for a total of about 1 month during this period by work on other projects in nearby areas. Previous to the geophysical surveys, a preliminary examination was made by H. R. Joesting to determine if geophysical methods could be utilized in exploring the area. 5/Field measurements were made by L. O. Bacon and J. H. Getz, project geo¬physicists of the Bureau of Mines, under the general supervision of H. R. Joesting. A grid survey of the area, to locate geophysical stations, was made by Paul Russell, Bureau of Mines engineer, who also collected specimens for laboratory tests. Most of the computations and the preliminary magnetic and resistivity maps were made by L. 0. Bacon."

Feb 1, 1948

By W. P. Yant

A previous report of the Bureau of Mines dealt with the toxicity of dichlorodifluoromethane5, a new refrigerant that has a remarkably low toxicity. Continued research by the Prigidaire Corporation6 and toxicological experiments performed in the Laboratory of Applied Physiology of the University of Cincinnati7 revealed another organic fluoride, dichlorotetrafluoroethane, whose toxicity also appeared to be of a very low order and whose physical-and chemical properties make it suitable for refrigeration purposes. In addition to low toxicity, safety in its use is further enhanced by its physical properties, which permit the design of equipment that operates at comparatively low pressures and hence mitigates the dangers and problems of leakage. The investigation described in this report was performed by the Bureau of Mines at the request and with the cooperation of the Frigidaire Corporation.

Jan 1, 1932

This chapter summarizes data on crude mineral production for the United States, its island possessions, and the Common-wealth of Puerto Rico. Included also are tables that show the principal mineral commodities exported from and imported into the United States, and that compare world and U.S. mineral production. Except for the mineral fuel commodities, the detailed data from which these tables were derived are contained in the individual commodity chapters of volume I and in the State chapters of volume II of this edition of the Minerals Yearbook. In October 1977, responsibility for the collection of data on mineral fuels-coal, petroleum, natural gas, and natural gas liquids-was transferred to the newly created Department of Energy. Although chapters covering these commodities will no longer appear in Volume I of the Minerals Yearbook, quantity and value data have been included in most of these summary tables to maintain statistical consistency in State and national value of overall crude mineral output. This shift in responsibility has also resulted in changes to the composition of the "Nonmetals" and "Mineral Fuels" groups in table 1 and table 2. The commodities-asphalt and related bitumens (natural), carbon dioxide (natural), helium, and peat-have been removed from the "Mineral Fuels" group, and are now included under the "Nonmetals" group. There has been no change in the components of the "Metals" group.

Jan 1, 1980

By G. L. Oldright, F. S. Wartman

"In the process of smelting copper ores and secondaries in the reverberatory furnace to produce a copper matte and a slag low enough in copper content to be discarded on the dump, it is essential to the best functioning of the process that most of the iron in the material charged into the furnace be at the end in the form of sulphide in the matte or ferrous oxide in the slag. Ferric oxide and magnetite present in the charged material should be reduced to ferrous sulphide or oxide. Ferric oxide offers no difficulty in reduction, at least to the magnetite stage, because it reacts very readily with sulphides at quite low temperatures. Magnetite is less reactive and consequently more resistant to slagging, so that the furnace man must take advantage of all factors favoring its reduction in order to prevent accumulations in the furnace.In order to determine these factors more definitely, the Bureau of Mines in cooperation with the Department of Metallurgy, University of Arizona, has undertaken at the Southwest Experiment Station an investigation of the effect of various factors upon the rate of reduction of magnetite by ferrous sulphide. A previous paper's reported the nature of the reactions taking place and the effect of various physical factors when only pure sulphide and oxide were present. Since in the actual smelting operation, many other substances are also present, it seemed desirable to make a study of the effect of their presence upon the rate of reduction of magnetite by ferrous sulphide. Such a study has been made; the work done and the results obtained are described herewith.As will be shown later, it has been found that of the substances usually present in the smelting charge, silica and magnesia accelerate, whereas lime, alumina, and cuprous sulphide hinder the reduction of magnetite by ferrous sulphide.No report of a previous laboratory investigation of this subject has been found. Almost all furnace operators have made at one time or another at least qualitative ccmparisons of the effect of various changes in operating oonditions upon the behavior of magnetite in the furnace, but the conclusions derived from the experiments have never been published."

Mar 1, 1931

By Nicholas R. Dixon

This report summarizes all work performed under Phases I, II and III of U.S. Bureau of Mines Contract H0387006, "Development of a Prototype Retrofit Noise Control Treatment for Jumbo Drills." The noise and vibration levels of four jumbo drills were characterized and a survey of percussive rock drill usage is reported. A Gardner-Denver DH 123 drill was chosen as a demonstration drill, and extensive noise diagnostic studies were performed. Noise control treatments were designed, developed and evaluated in a reverberant drill test facility. The treatments consisted of an integral enclosure/muffler for the drifter, vibration isolation of the drifter from the enclosure and feed, and a drill steel sheath. A 19 dBA reduction in overall sound power level was achieved with no loss in drilling rate. The prototype retrofit treatments were field tested in an aboveground mine and in a production section of an underground zinc mine. Long-term durability and operator acceptance of the enclosure/muffler treatment were excellent. Preliminary evaluation of the drill steel sheath was encouraging, although additional testing is required.

Jan 1, 1982

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

By Michael M. Hamilton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine mineral resources and resource potential in and adjacent to the North fork Smith RARE II study area. Most mineral resources identified in this area are in laterites, highly-weathered residual soil zones. In the RARE II area, resources of nickel, cobalt, chromium, and magnesium were identified at 15 laterite properties and chromium resources at one chromite mine. Other commodities include copper, gold, silver, and mercury (fig. 1). Approximately 1,100 lode and 1,200 placer claims have been located in or adjacent to the area. Most placer claims are for literites. There are no patented claims or mineral leases. Forty laterite deposits on 15 ,properties within the RARE II area (fig. 2) contain about 16 million tons of identified marginal reserves and subeconomic resources containing nickel, cobalt, chromium, an magnesium (table 1). Most deposits have keen explored and are currently claimed. California Nickel Corporation is developing laterites on Gasguet Mountain, within and adjacent to the southeastern and western parts of the study area. If this project proceeds to production, a laterite processing plant on Gasquet Mountain would enhance the minability of other deposits in the study area. The Climax, PFM, DF, and Stone Corral properties (fig. 1, nos. 1, 6, 9, and 23) have deposits of sufficient tonnage and grade to attract mining interest; resources at these properties are in and adjacent to the RARE II area.

Jan 1, 1983

By F. H. Gunnell, W. C. Dunham

"INTRODUCTION The Treasure Hill mines, situated in Dry Canyon, Ophir mining district, Tooele County, Utah, together with several other properties in the district, examined were examined by Frank L. Wideman, an engineer, the Bureau of Mines, in September 1942.In April 1945, development drilling was started on the Treasure Hill mines, which are operated under lease from the Madison Mines Co. The project was continued in 1946 and terminated in 1947.While the Bureau of Mines project was in progress, the Morgan and Fullion tunnel workings were surveyed by Bureau engineers.ACKNOWKEDGEMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy, It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative perk, and prepares the final report. The Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests. The work here described was under the direct supervision of Paul T. Allsman, chief, Salt Lake City Division, Mining Branch."

Jan 1, 1948

By C. H. Bloomster

This study estimated (1) radon and radon daughter emissions from underground uranium mines; (2) the reduction in radon that would be released to the surface by using control techniques such as bulkheads, sealants, backfilling, and positive pressure ventilation; (3) the cost for radon and radon daughter removal from total exhaust air; and (4) total radon and radon daughter discharge for lower occupational exposure limits. For 13 large underground uranium mines, estimated yearly radon emissions from each mine ranged from 900 to 3,400 Ci. The estimated age of air emitted from the mines ranged from 11 to 37 min. Potential radon removal methods for the total mine exhaust were evaluated. The cost of these methods was prohibitive. Diurnal and seasonal changes may affect radon emission over short periods of time, but do not affect the total emissions over the long run. Radon and radon daughter emissions would be little changed by increased ventilation requirements needed to achieve lower occupational exposure limits. The concentrations in the exhaust would be lower, but the total release would be the same

Jan 1, 1984

A knowledge of the mechanics of wave propagation through the earth is essential if reliable communication systems are to be designed for coal mine environments. To obtain a reliable basis from which accurate propagation predictions could be drawn, a series of theoretical Studies have been prepared for the Bureau of Mines by Mr. Ramsay Decker of Spectra Associates, Inc. through a subcontract with Collins Radio Group. These reports formulate the analytical techniques from which wee may derive frequencies and antenna configurations that yield the optimum signal-to-noise ratios over the greatest distances in mine environments. The reports of sections 2 and 4 deal with analytical techniques for determining the signal-to-noise ratio within a mine environment for loop-to-loop and line source-to-loop antenna configurations. The analytical results of these reports were then implemented into computer programs to obtain predictions concerning through-the-earth signal propagation. These preliminary predictions are based on noise data compiled by Bensema, Maxwell and Stone, and WVU prior to the extensive research conducted by the National bureau of Standards (NBS). These initial measurements indicated a 20- to 30-dB lower noise level than that measured recently by N BS. The recent NBS data is that used by Collins in the final predictions.

Jan 1, 1974

By W. P. Yant, G. W. Jones

"Introduction.During the past two years the Bureau of Mines has conducted a study of natural-gas heaters*** to determine (1) what types of heaters literate carbon monoxide; (2) why carton monocide is liberated; and (3) how, by change of design or construction, the liberation of this gas can be largely eliminated, In addition to the above study the bureau has investigated cases in the Pittsburgh dis¬trict where fatalities have resulted from carbon monoxide given off by natural-gas heaters.Since these fatalities were first brought to the attention of this bureau through the press, it is likely that some cases were missed and thus not listed. On the other hand, some cases reported as being due to carbon monoxide poisoning, on investigation were found to be due to causes other than carbon monoride.The cases listed herein were shown in all probability to be due to carbon monoxide. Those in which there is any doubt have been omitted; so have those in which there was part asphyxiation, where the victims later recovered."

Feb 1, 1924

By Gabriel S. Esterhuizen, Anthony T. Iannacchione

The roof rock in underground limestone mines in Northern Appalachia can be subject to high horizontal stresses in spite of the shallow depth of the workings. The high stresses can cause roof stability problems. The National Institute for Occupational Safety and Health staff have observed a distinctive asymmetrical mode of failure at the pillar-roof contact in two underground stone mines, which is different from the typical failure mode observed in response to excessive levels of horizontal stress. A dip of greater than 5° was identified as a possible cause of this mode of failure. Numerical model experiments showed that an increase in the dip of the workings can cause an increase in the stress at the up-dip corner of the roof beam. A case study is presented in which failure at the pillar-roof contact was observed where the dip of the workings was 7° in a high horizontal stress field. Numerical modeling showed that the relatively small dip of the workings could have induced stresses changes in the immediate roof that would explain the failures. The model results also showed that this mode of failure is less likely to occur if the limestone pillars contain weak bedding planes that provide stress relief. In addition, the results showed that for the conditions at the case study site, the stress in the roof beam was not sensitive to the thickness of the roof beam or to the excavation span. The high horizontal stresses at this site are an important contributing factor to the observed failures.

By Elbridge W. Gresseth

Rock deformational structures in a deep mine were analyzed by petrofabric techniques to learn (1) the relative magnitude and direction of the principal stresses involved in tectonic deformations prior to mining, (2) the preferred orientation of rock planar discontinuities which define rock anistropy prior to mining, and (3) the relationship of mining-induced rock failure to inherent rock stresses and inherent rock anisotropy. Rock fabric elements used for petrofabric analysis consisted of bedding planes, faults, joints, fractures, foliation, sericite plane (001), quartz axis [0001], quartz deformation lamellae, and microfractures. Structures and structural symmetries from different areas within the mine and from different scales of observation were compared to learn the nature of rock anisotropy and the orientation of the principal stresses defined by rock deformations. Analysis of such fabric as regional and macroscopic faults, b-c joints, quartz [0001], sericite (001), and microfractures, indicate that during the epochs of tectonic deformation, the maximum and minimum principal stresses were horizontally oriented and acted along northwest and northeast axes, respectively. This condition of regional stress appears to have continued during folding and the associated period of faulting. The most recent tectonic deformation represents a rotation of the minimum principal stresses into a vertical position, as shown by the development of a tensile joint system, quartz deformation lamellae, and microfractures. Good interscale correlation and statistical homogeneity of tectonic fabric indicate a stress field homogeneity in this area during tectonic deformation. Rock physical anisotropy is genetically associated with tectonic fabric and consists of preferentially oriented planar discontinuities intersecting along a nearly vertical axis. The mining-induced deformations were correlated with the inherent rock anisotropy which either directly controls or greatly affects their development. This phase of rock deformation shows a greater degree of stress field heterogeneity than was the case with tectonic deformations This is explained as a result of nonconfinement afforded by underground openings and the increase in ground stresses due to mining activity"

Jan 1, 1968

By Charles L. Kimbell

In 1988, the aggregate value of total world international export trade in mineral commodities was estimated at nearly $542 billion in current (1988) dollars, which was about 8.6% above the 1987 level, but still 23.7% below the record high set in 1980. Comparable comprehensive data for 1989 were not available in time for inclusion in this chapter, but 1989 returns for developed market economy countries only were 1 1.8% above those for 1988. These countries accounted for about 50% of the total mineral commodity export trade in 1988. It would be unsound to utilize the overall 11.8% growth rate for mineral commodity export trade for these countries to extrapolate the growth in total world mineral commodity trade because these developed market economy countries account for substantially different shares of the five major mineral commodity groups listed in table 2. Specifically, developed market economy countries in 1988 accounted for 56% of world export of ore, concentrate, and scrap, 74.7% of world exports of iron and steel, 71.7% of world exports of nonferrous metals, and 57.8% of all exports of crude nonmetals, but only 26.6% of world exports of mineral fuels. Moreover, even within each of these groups, the actual product mix included in developed market economy country aggregates differ from that in developing market economy country aggregates and in centrally planned economy country aggregates. Nonetheless, an increase of 9% to 12% in the value of world mineral commodity export trade seems indicated by available returns.

Jan 1, 1992

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By Pramod C. Thakur

In This Chapter [Origins of coalbed methane Reservoir properties of coal seams Thresholds for coal seam degasification Methane emissions in mines Methane drainage techniques How to transport gas safely in mine pipelines and Economics of coal seam degasification Recommended publications on coal seam degasification are Gas Control in Underground Coal Mining [Creedy et al. 1997], Coalbed Methane Extraction [Davidson et al. 1995], and Methane Control for Underground Coal Mines [Diamond 1994].] ORIGINS OF COALBED METHANE AND RESERVOIR PROPERTIES OF COAL SEAMS Origins of coalbed methane. Coal seams form over millions of years by the biochemical decay and metamorphic transformation of plant materials. This coalification process produces large quantities of byproduct gases, such as methane and carbon dioxide. The amount of these byproducts increases with the rank of coal. It is the highest for anthracite, where for every ton of coal nearly 1,900 lb of water, 2,420 lb (20,000 ft3) of carbon dioxide, and 1,186 lb (27,000 ft3) of methane are produced [Hargraves 1973]. Most of these gases escape to the atmosphere during the coalification process, but a small fraction is retained in the coal. The amount of gas retained in the coal depends on a number of factors, such as the rank of coal, the depth of burial, the type of rock in the immediate roof and floor, local geologic anomalies, and the tectonic pressures and temperatures prevalent at that time. The gases are contained under pressure and mainly adsorbed on the surface of the coal matrix, but a small fraction of gases is also present in the fracture net-work of the coal. Methane is the major component of gases in coal, comprising 80%–90% or more of the total gas volume. The balance is made up of ethane, propane, butane, carbon dioxide, hydrogen, oxygen, and argon.

Jan 6, 2006

By Todd M. Ruff

The majority of fatalities that occur in road construction work zones in the United States involve a worker being struck by a piece of construction equipment or other vehicle. The Spokane Research Laboratory of the National Institute for Occupational Safety and Health, in cooperation with the Washington State Department of Transportation, is evaluating methods to decrease these accidents. One such method uses devices that assist equipment operators in monitoring blind areas around the equipment to prevent collisions with workers on foot or other objects. Several cameras and sensor systems are available for this application, and a study was conducted to evaluate these systems on various trucks used in road construction and maintenance. Tests were conducted using sanding trucks during the winter months, which allowed researchers to investigate the effectiveness and limitations of various technologies under the most extreme conditions. Tests were also conducted using dump trucks during the warmer months to study the effectiveness of the systems in highway work zones. Results show that many difficulties arise when using camera and sensor systems in cold, snowy climates. And, while the operation of these systems is more reliable during the warmer months, challenges still exist in using them on equipment in crowded work areas.

Jan 1, 2004

By A. C. Richardson

The mine of the Porter Coal Co. is located at the town of Porter in the northwestern part of Jefferson, County, Ala., about 20 miles west of Birmingham. The operations in this mine are confined to the middle and bottom benches of the Mary Lee bed. The coal from the Porter mine is handpicked and washed before being placed on the market. The handpicked lump coal and the washed egg and nut, coal are sold chiefly as domestic and steam-raising fuel. The coal finer than 1 inch is washed in 2-compartment jigs and utilized in the manufacture of metallurgical coke. The coal company has found that, when coal ranging in size from 1 to 0 inch is washed in jigs, a considerable amount of high-ash material finer than 3/16 inch remains in the washed coal. This paper gives the results of an investigation which was conducted for the purpose of determining the washing characteristics of the through 316-inch raw coal and the extent to which the ash might be reduced by means of coal-washing tables. This investigation has been made in connection with an. extensive study of the coal-washing problems now being conducted by the United States Bureau of Mines and the University of Alabama, with the cooperation of the coal-mining companies of the State.

Jan 1, 1933