Search Documents

By George J. Conroy

Techniques for locating trailing-cable faults are discussed, particularly those techniques suitable for use in underground coal mines, which have been the subjects of Bureau of Mines research. The discussion concerns precautions and suggestions for locating faults, rather than detailed descriptions of apparatus.

Jan 1, 1979

By Wilbur I. Duvall

In this report, the Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole the boundary of which is loaded by applied radial stresses over four separated arcs. The problem solved is a two-dimensional approximation of the stresses and displacements developed by a large tunnel-boring machine anchored in a circular tunnel. Analysis of the solution shows that the tangential tensile stresses induced on the boundary of the circular opening can be minimized in the roof and maximized in the floor of the opening by proper spacing and loading of the four arcs.

Jan 1, 1967

By Neil B. Young

Analytical results for nahcolite, dawsonite, total extractable alumina, and oil yield are presented for samples representing Green River Formation oil shales in the saline section of two cores from Colorado's Piceance Creek basin. Analyses are also reported for samples extending the analyzed section of Colorado corehole No. 3 beyond that reported previously. These data permit evaluation of the deposit for possible production of three coproducts--shale oil, alumina, and sodium carbonates--from the saline section of the formation at these sampled points.

Jan 1, 1970

Investigate the use and placement of lightweight concrete to improve ground control technology in deep mines where deformation occurs under heavy ground conditions and where there is danger of rock bursts. Approach Investigations of lightweight concrete properties and placement methods were conducted in the laboratory and in the field. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a test section constructed in a mine drift using an air-supported formwork. In the two underground test sections, the light-weight concrete was placed using a piston pump with concrete discharge line. A cooperating mine also used lightweight concrete, in the density range of 25 lb/ft3, to replace timber blocking in a raise preparation structure (the enlarged area across a vein where chutes and manway access arc placed). Other experiments included the use of precast lightweight concrete blocks in situations where ground support was needed, such as fur mine, ventilation doors, stoppings, and barricades.

Jan 1, 1990

By Donald W. Fausett

This Bureau of Mines publication presents a system of thermal decompositions providing an adequate description of the mechanism of oil shale pyrolysis. Specific rate constants for systems of thermal decompositions studied are estimated via a least-squares procedure. The estimates thus obtained provide a mathematical model of the corresponding thermal decomposition system. A model that generates a good fit to published Bureau of Mines experimental data, in comparison with other models studied, is based on a thermal decomposition system consisting of two first-order reactions and three second-order reactions. Values computed for the specific rate constants corresponding to this system are shown to exhibit a temperature dependence that is in good agreement with the Arrhenius equation.

Jan 1, 1974

Aid mine workers in detecting hazardous roof conditions in underground mines by developing a method of roof sounding which supplements or replaces the traditional roof sounding technique where the miner relies on experience to determine whether or not the rock is sound. Approach The Bureau of Mines developed an electronic roof sounding de-vice that acoustically determines the integrity of mine roof rock by "listening" to the variation in frequency vibrations within the rock. How It Works n previous research, the Bureau of Mines found that loose rock in a mine, when impacted, vibrates at a much lower frequency and for a lower time period than does a solid slab. By quantifying the enhancement of low frequency vibrations in loose rock over solid rock, a repeatable, objective measure of the rock's soundness can be obtained. This approach was used in developing the rock stability tester.

Jan 1, 1986

Develop a cost-effective diesel aerosol sampler that can be used by industry and regulatory agencies to determine the diesel exhaust aerosol concentration in mine atmospheres. The sampler must be easy to use, wearable by mine personnel, compatible with current personal sampling protocols, and inexpensive. Approach The University of Minnesota (University) and the U.S. Bureau of Mines (USBM) have developed and tested a prototype diesel exhaust aerosol sampler. The sampler, however, was complicated and expensive to fabricate. Consequently, the USBM redesigned the sampler to simplify both manufacturing and use, and the sampler was evaluated to ensure equivalency with the prototype. Background The National Institute for Occupational Safety and Health (NIOSH) has recommended that "whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration." In addition, the U.S. Mina Safety and Health Administration (MSHA) has been directed by an advisory committee to establish a diesel exhaust aerosol standard and regulations to minimize exposure to diesel pollutants in underground coal mines.

Jan 1, 1992

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult and longstanding engineering problems associated with coal mining is the catastrophic failure phenomenon known as coal mine bursts (known in the United States as bumps). For more than 70 years, researchers and practitioners have attempted to determine whether this destruction observed underground is caused by stress conditions within the coal pillar or from distant seismic sources in the mine roof and floor strata. The role of confinement and the extent of failure in solid pillars and panels have also proven difficult to define. These are important issues, since control solutions need to be based on a fundamental understanding of the problem. Obsenations by U.S. Bureau of Mines researchers over the last decade have helped to clarify certain aspects of these issues. Microseismic sensors and geomechanic field measurements have located areas of excess energy release, identified stress conditions in coalbeds close to failure, and recorded the response of mine structures prone to bursts. In the present study, data available for a range of U.S. bursts were considered in an effort to evaluate both common and distinctive features. Although the attempt revealed little commonality, encouraging results were produced by categorizing coal bursts by source mechanisms. When a coal burst is thus categorized, differences in environmental factors-such as geology, stress fields, and mining methods-are highlighted, and viable control strategies are readily recognized.

By Michael J. Brnich

On November 20, 1968, a massive explosion rocked the underground workings of Mountaineer Coal Co.?s Farmington No. 9 Mine in West Virginia. Of the 99 miners who were working in the mine at the time of the explosion, only 21 survived and escaped the mine. This group included eight who were rescued from the Mahan?s Run air shaft. Nearly 40 years after the event, researchers from the NIOSH Pittsburgh Research Laboratory conducted oral history interviews with two of the eight survivors rescued from the shaft. The Farmington No. 9 Mine disaster ultimately led to passage of the Federal Coal Mine Health and Safety Act of 1969 (amended in 1977).

May 1, 2009

By H. J. Sloman

"INTRODUCTION Industry, including coal mining, has come to realize that to prevent accidents the human element must be given more consideration than was customary in the past. In formulating safety rules and regulations and in the enactment of laws governing mining, too often enforcement is emphasized rather than the means of gaining willing compliance.' The purpose of this paper is to call attention to the human side of accident prevention, and the approach to this important and much-discussed subject will deviate somewhat from the usual discussions.The human being is a complex mechanism, both physically and mentally. It is difficult to establish a common denominator for the actions of humans, except in general. In establishing mining laws, rules, regulations, and standards, the ultimate objective should be to gain the best possible response of workmen, so that optimum results in accident prevention may be obtained. The complexity of human beings is apparent when the many ways 1n which they differ are considered. Some of these differences are manifested in emotional and phlegmatic types, degrees of intellect or native intelligence; and in hopes, desires, aspirations, and philosophies of life. How much simpler ac¬cident prevention would be if the response to laws, rules, regulations, or standards were equivalent to the definite movements of puppets responding to pulls on strings. Each time, the strings are pulled in exactly the same way, the puppets will respond in exactly the same manner. Human beings, although having many similar characteristics, do not respond uniformly to identical ""string-pulling""; therefore, much study is necessary before the desired re¬sponses can be obtained. To achieve the ultimate in accident prevention, it must be ""worked at"" constantly. Regardless of the adequacy of safety laws, rules, regulations, or standards, good accident records will not ""roll in"" if dude consideration is not given to the personal traits of those most likely to be involved in accidents."

May 1, 1948

By T. M. Klemetti, G. M. Molinda, D. M. Pappas

Some of the most difficult coal mine roof in the U.S. can be found in the Illinois Basin. Factors contributing to the high roof fall rate include: weak moisture-sensitive roof rock, high horizontal stress, and limited longwall mining. The depth of cover ranges from 90-1,000 ft and roof damage from horizontal stress can be severe. Moisture sensitive-roof rock is common above the Springfield-Harrisburg Herrin #5 and #6 seams in the Illinois Basin, and contributes to roof skin deterioration. The roof fall rate increases significantly in the humid summer months. The National Institute for Occupational Safety and Health (NIOSH) has shown, using lab and field studies, that highly moisture-sensitive roof rock can be directly correlated to poor roof conditions. Controlling the skin is the key to reducing rock fall injuries, and roof screening is, by far, the best remedy. Illinois Basin coal operators have been successful in reducing the number of rock fall injuries in recent years. NIOSH has documented best practices for screen installation which has resulted in safe, efficient operations. Other solutions to skin failure include: the use of denser five bolts per row patterns to reduce spans between bolts, systematic supplemental support in intersections, straps and large pans protecting operators, and air conditioning to remove moisture from the intake air.

To improve the efficiency and speed of under-ground post-disaster rescue operations. The Approach: Develop a battery-powered mine-rescue vehicle designed to carry rescue crews, rescued miners, and their support equipment. How It Works: The experimental vehicle, shown below, was designed and constructed by the Mine Safety Appliances Company under contract to the Bureau of Mines. ATV Manufacturing Company and Delco Electronics were subcontractors. A rechargeable, silver-zinc battery provides power to a 3-horsepower permissible motor, the speed of which is regulated by a solid-state controller. Three wheels on each side are independently driven by a chain and mechanical trans-mission.

Jan 1, 1974

By Joseph A. Sutton

The prospect of utilizing bacteria in mining and metallurgical processes introduces a new and challenging area of investigation. Elements of bacteriology and metallurgy are discussed in connection with possible areas where biological science might be applied in extractive metallurgy. Bacteria may prove important in the selective separation of metals from ores and metallurgical solutions, the production of sulfur from gypsum or pyrites, and the production of sulfuric acid from elemental sulfur. A series of reports concerning the experimental applications of bacteria on minerals and metallic ores will follow this paper. For several years the Bureau of Mines has been investigating the action of bacteria in the oxidation of sulfide minerals and their potential uses in metallurgical processes. Primary attention has been given to the possible utilization of certain strains of autotrophic bacteria that live in industrial leaching solutions or fractures of mineral outcrops. The purpose of this paper is to acquaint the mining and metallurgical engineer with micro-organisms and some of their possible applications in the field of extractive metallurgy.

Jan 1, 1961

By Roy C. Bartholomae

This U.S. Bureau of Mines study found that the performance of the active noise cancellation hearing protector in a reverberant field was mixed. The performance varied when the conditions changed from ideal to nonideal. The active noise cancellation (ANC) component provided substantial additional noise reduction from 125 to 500 Hz for all testing conditions (broadband noise or pure tones both with and without safety glasses). While the ANC under ideal conditions provided additional attenuation from 500 Hz and below, under nonideal pink noise conditions the ANC amplified noise below the 125-Hz third octave band. There was a middle band of frequencies at which the ANC amplified noise levels ranging from 630 to 4,000 Hz. The results for pure tones showed that attenuations were higher but that they followed the same general trend.

Jan 1, 2010

By D. Harrington

"A tabulation is printed below showing the accident record of the thirty-two mines of the Anaconda Copper Mining Co., in Montana, for the years 1915, 1916, 1917, 1918, 1919 and 1920, with summation for the six years. The table gives the number of shifts worked by each mine with the serious plus fatal accident rate for each 10,000 shifts worked.It is seen that in a total of 16,460,767.5 shifts worked by employees of the company's mines during this six-year period, there were only 2,005 serious and fatal accidents and of these, 200 were fatalities, leaving 1,805 serious accidents (a serious accident being one in which 14 or more days' time are lost). This is at a rate of 9,120 shifts per serious accident and at a rate of 82,304 shifts per fatality. Hence, if 300 days be adopted as a year's work, there would be one fatality per 274.3 years of work in these mines and one serious accident for every 30.4 years work.According to Bureau of Mines Technical Paper 286, (Metal-mine accidents in U. S. in 1919, by W. W4 Adams), during the years 1916, 1917, 1918, and 1919, the metal mines of the United States worked a total of 210,548,640 shifts and had 39,705 serious accidents. During the same years, according to the following tabulation, the mines of the above-mentioned company worked 11,958,978 shifts and had a serious accident rate of 0.995 accidents per 10,000 shifts worked. If the metal mines of the United States, working these 210,548,640 shifts, had this company's serious accident rate of 0.995 serious accidents per 10,000 shifts, the total number of serious accidents would have been only 21,000 or the country's metal-mine serious accidents would have been reduced nearly one-half, and there would be 18,705 fewer serious accidents than actually occurred."

Jun 10, 1921

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The Bureau of Mines made laboratory absorption measurements on oil shale samples, which showed that the amount of methane absorbed is proportional to pressure and oil yield, and can be much larger than would be predicted based solely on porosity. Oil shale cores collected in the field were also measured for their gas content using the Bureau of Mines direct method, Cores taken from deep locations and far from outcrops yielded more gas than cores from shallower locations or at outcrops, when taking into account variations in oil yield, and all data indicate that oil shale mines that are both deep and far from an out- crop will emit low levels of methane gas.

Jan 1, 1977

By Robert L. Chufo, H. Kenneth Sacks

Medium-frequency (MF) waves can propagate in a coal seam, bounded above and below by conducting rock, in an approximate transverse electro-magnetic (TEM) transmission-line mode with the electric field vertical and the magnetic field horizontal. The theory of this coal seam mode is applied to recent MF data for a number of mines in order to classify the propagation characteristic of the mines in a simple way. When conductors such as rails, trolleylines, or power cables are present in the vicinity of the measurement path, it is found that the magnetic field versus range plots have two distinct regions with very different slopes. This effect is attributed to coupling of the cylindrically spreading coal seam mode to a low-attenuation conductor guided mode. As a result, voice communications range between mobile transmitters can extend several thousand meters. The use of MF for mine communications is discussed.

By Robert A. Bruce

A motion transducer based on coherent mixing of laser light backscattered from rough surfaces is evaluated in terms of sensitivity, bandwidth and range. Tests made with a prototype composed of a 4-mw HeNe laser, a silicon avalanche photodiode, and a 15-cm aperture telescope demonstrate that remote measurements with reasonable bandwidth and accuracy are feasible at distances up to 100 meters.

Jan 1, 1977

By M. H. Stanczyk

Bench-scale laboratory tests were made by the Bureau of Mines of a segregation-flotation concentrate, assaying 20.43 percent copper, to investigate the influence of various ratios and concentrations of ammonia and carbon dioxide on copper extraction. Leaching the concentrate with a solution containing 900 pounds of ammonia and 360 pounds of carbon dioxide per ton of feed, followed by washing the leach residue with 1.75 tons of a 10-percent solution of ammonium carbonate and about 1 ton of water (as steam) per ton of solids, resulted in a copper recovery of 96.3 percent. Resegregation and flotation tests of the washed residues revealed that 85 percent of the copper in the residue could be recovered. Steam distillation tests of a typical ammoniacal leach liquor, assaying 39 grams copper, 105 grams ammonia, and 77 grams carbon dioxide per liter, recovered over 99 percent of the copper as a mixed oxide-carbonate precipitate. The ammonia losses in leaching, filtering, washing, and distillation were 0.12 pound per pound of copper recovered in the precipitate. Calcination and subsequent hydrogen reduction of the precipitate yielded a metallic copper powder assaying 98 percent Cu, 0.87 percent Si02, 0.10 percent MgO, 0.54 percent CaO, and 0.41 percent R203.

Jan 1, 1961

By Donald O. Capstick

In 1481, U.S. Bureau of Mines personnel conducted a survey of mines, prospects, and mineral resources in the Table Mountain RARE II area. There are no mines or active prospects in the study area. One prospect in the study area, the Waterfall Prospect, is estimated to contain 480 tons (440 t) of indicated subeconomic tungsten resources averaging about 0.18 percent tungsten trioxide (W03). Other tungsten occurrences are at the Stevens Prospect, just northwest of the area. Stone and sand and gravel deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 4,400-acre Table Mountain study area is 13 mi (21 km) southwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir wilderness adjoins the study area on the southwest (fig. 1).

Jan 1, 1982