Search Documents

By M. C. Chapman, E. C. Westman, A. T. Iannacchione

Examination of seismic records during the time interval of the Sago Mine disaster in 2006 revealed a small amplitude signal possibly associated with an event in the mine. More needs to be understood about the seismicity from mine explosions in order to properly interpret critical seismic information. A seismic monitoring system located at NIOSH’s Lake Lynn Experimental Mine has monitored experimental gas and dust based explosions and impact tests. The seismic signatures from these different events were analyzed using standard waveform analysis procedures. The magnitude of seismic energy during a gas and dust explosion was found to be more dependent on mine entry geometry and seal behavior rather than on the amount of explosive fuel present. The results suggest a large explosion that’s not restricted can generate potentially the same magnitude as a small explosion that is restricted.

By J. J. Forbes

The Act of Congress authorizing the establishment of the United States Bureau of Mines became effective July 1, 1910. One of the most important duties Congress delegated to the Bureau in this Act was the study of health and safety conditions in the mineral industries. Early investigations of these conditions revealed the need of prompt Care of injured employees, as, under the difficulties inherent in their occupation, seemingly unimportant wounds if not treated promptly might become infected and cause permanent disability or even death. Many seriously injured persons brought out of mines and plants by fellow workers ignorant of approved methods of giving first aid or of safe means of transportation have been caused suffering and have had injuries accentuated to such a degree as to bring about permanent disability or death. The need of general instruction in first aid thus became apparent. BRIEF HISTORY OF FIRST-AID WORK The education of miners in the United States in first aid probably was conducted systematically first by the anthracite industry in Pennsylvania. Subsequently, first-aid training was carried on actively in Alabama and Indiana. Meanwhile, a general training campaign was carried on among industrial workers by the American Red Cross Society; when the Bureau of Mines began its nation-wide campaign of instructing employees of the mineral industries, the Red Cross turned over that part of its industrial training work to the Bureau but continued to cooperate by furnishing surgeons as judges in important first-aid contests and demonstr tions and assisted for a number of years in determining training methods.

Jan 1, 1937

To facilitate compliance with title 30 CFR 75.1001-1(b), which requires testing and calibrating of trolley line automatic circuit interrupting devices at intervals not to exceed six months. Approach Calibration of a circuit breaker ideally implies the passage of the expected fault current through the sensing circuit, and observing a successful circuit interruption at the preset level within a specified time. On trolley lines, the required current may be a few thousand amperes, with maximum duration well exceeding one-tenth of a second. Any method of obtaining this calibration current Involving the trolley wire can contribute to wire sagging and other permanent damage to the haul-age system due to the high energy dissipated during the test. Also, control to assure that exactly the required level and duration of current flow is obtained implies the use of equipment which is simply not available In the ordinary mine. Under a Bureau of Mines contract, a circuit to achieve the necessary calibration pulse was conceived and built. How It Works Two prototype units were fabricated and have been field tested by MSHA technical support engineers in under-ground mines. The equipment consists of an electronics Package 20 x 24 x 8 inches and weighing 93 pounds, including a side-mounted circuit breaker, with a set of 8 foot long detachable, AWG #4/0 leads with plier-type clamps. The total lead assembly weighs 21 pounds.

Jan 1, 1981

By Jerry W. Ramsey

The Bureau of Mines studied two Pennsylvania anthracites using low-temperature carbon dioxide adsorption. A modified form of the Brunauer-Emmett-Teller equation was used to calculate specific surface areas. Two mesh sizes of each anthracite were used to determine how gamma irradiation at 106 and 108 rads, both in vacuum and in the presence of air, affected the carbon dioxide surface areas. Results show that anthracites have a system of pores that are essentially all interconnected rather than isolated; that anthracites differ from one another in specific surface, which may correlate with density; and that irradiation in vacuum has no discernible effect on specific surface of anthracite, but irradiation in air does produce changes in specific surface.

Jan 1, 1966

By Jennifer A. Slatnick

The U.S. Bureau of Mines estimated the potential availability of titanium from 39 mines and deposits in 12 market economy countries. The evaluated properties account for 76 pet of the market economy country demonstrated resources, which total 603 Mt of contained titanium dioxide (Ti02) in the minerals rutile, ilmenite, leucoxene, and anatase, and represent 95 pct of current production. Approximately 250 Mt of contained Ti02 could be economically recovered from evaluated titanium operations at January 1992 market prices. In terms of mineral concentrates, this equals approximately 19 Mt of rutile concentrate, 110 Mt of ilmenite concentrate, 47 Mt of synthetic rutile concentrate (in addition to the ilmenite), and 160 Mt of titanium slag that could be recovered. Over the past decade, the titanium minerals industry has adapted to the changing market. In the 1980's, titanium producers expanded production because of the rising demand for titanium products. Today, the titanium industry is in a state of overcapacity, and byproduct revenues, such as that from zircon, have become essential in keeping operations profitable. The industry has also witnessed a greater dependence on upgraded ilmenite products, such as titanium slag and synthetic rutile, because of the expense of rutile and the lower wastes emitted from these upgraded products. As a result of this dependence on upgraded ilmenite products, South Africa has become a leading titanium producing country and has displaced Australian production.

Jan 1, 1994

By I. AITKENS

It is a common misconception that all yellow stones are topazes and that all topazes are yellow; but neither statement is true. The real topaz is a rather rare mineral, and a large number of yellow stones that masquerade as topaz are nothing more than yellow quartz, known as citrine, but almost universally called topaz. The true topaz is often called "Brazilian" topaz by the jeweler to distinguish it from yellow quartz; nevertheless, both terms are freely applied in trade to other yellow stones. Topaz is considered the most popular yellow stone for jewelry and is often used as the principal stone in brooches or pendants, especially in old-fashioned ornaments. However, many other species yield pretty yellow stones, some of which are far more numerous and less costly than the topaz.

Sep 1, 1931

By Jalna R. Zatko

The Bureau of Mines, U.S. Department of the Interior, has developed a novel method of flocculation dewatering of phosphatic clay wastes using polyethylene oxide as the flocculant. Research was conducted to determine whether ethylene oxide gas was present in the air in the vicinity of disposed waste materials which had been flocculated with polyethylene oxide. Samples of clay waste materials containing polyethylene oxide were prepared in stoppered glass bottles in simulated disposal environments. Gaseous samples, removed over a 75-day period using an airtight syringe, were injected into a gas chromatograph that was capable of separating ethylene oxide from air. The presence of ethylene oxide gas was not detected in any sample. To determine possible degradation products of polyethylene oxide, the properties and reactions of ethylene oxide and its polymers were reviewed. Based upon the literature survey and experimental study, it was concluded that adverse environmental effects were not likely to result from the use of polyethylene oxide for flocculating phosphatic clay waste products.

Jan 1, 1980

By A. W. Khair, S. J. Jung

"A fundamental study of fragment size distribution and characteristics of fracture pattern is presented for the dynamic penetration of a conical bit into coal block. In this paper, damaged zones during crater formation and fragment size distribution were studied. Bit with a sharper tip angle and a smooth body configuration performed better penetration. Results suggest that in coal cutting the trend should be toward the face cleat direction using a sharper angled tip bits which consumes less energy for an optimum range of penetration depths, thus attaining maximum cutting efficiency and reducing fine fragments.1. INTRODUCTIONMuch research in the past has been done on energy requirements and mechanism of energy dissipation for ideal rock fragmentation in cutting process. However the mechanisms of energy dissipation or failure criteria for rocks in cutting process in order to evaluate the efficiency of energy requirements in specific rock fragmentation is not well understood. The formation of a crater in rock under the impact blow of a bit has been observed experimentally (Hartman, 1959). It is known that directly beneath the edge of the bit the rock is crushed into fine powder, toward the sides of the crater it chips out into relatively large fragments. (Sikarskie & Cheatham, 1973). Singh et al. (1967) investigated the cratering process under the two different conditions of static and dynamic loading. They found that the amount of energy consumed per unit volume of crater is unequal for the two different loading conditions. A complex network of fractures often extends downward and laterally into the rock below the bit. The surface of the specimens showed that the dynamic loading damaged larger area then the static loading."

Jan 1, 1989

By Richard E. Dawes

Physical variables, a principal factor in the economies of mineral production, affect both capital and direct operating costs. By using a revenue-cost system for the framework, the analyses of revenue and cost categories demonstrate the relative importance of groups of physical variables, whether explicitly defined or not, to a lead-zinc mining operation. Physical variables affecting the producer represent about 60 percent of the total system influence as expressed by cost ranking. Other physical variables affect the remaining costs as controlled by the smelter, the transporter, and the landowner. Such resource conservation aspects as mineral losses due to mining method and mineral processing constitute a portion of the total revenue effects of physical variables. The physical variable revenue-cost system presented in this report offers a framework for cost-benefit analysis of mineral related research.

Jan 1, 1969

By Bruce I. Thomas

In 1943, the Bureau of Mines investigated the occurrence of cassiterite in the gravels of Morelock Creek which flows into the Yukon River 32 miles east of the confluence of the Yukon and Tanana Rivers in central Alaska. Samples of the gravels were obtained by churn drilling test pitting, shaft sinking, and open-cut mining. The gravels along Morelock Creek are about 6 feet in depth and covered with about 2-1/2 feet of overburden. The overburden is frozen, but the underlying gravels are not. Cassiterite, with gold and other heavy minerals, is usually concentrated in the first 2 feet of' gravel above bedrock and in some places penetrates into joint planes in the bedrock. The various methods of obtaining samples are discussed, and drill logs and analyses are tabulated in this report.

Jan 1, 1948

By J. W. Walkiewicz

One of the objectives of the Bureau of Mines is to develop substitution technology for scarce materials. In accordance with this goal, alloys containing lanthanum, cobalt, copper, and magnesium were investigated for fabrication of rare-earth-cobalt (RE-Co) permanent magnets. A complete substitution of lanthanum for samarium and a partial substitution of copper for cobalt was accomplished. Magnets of La-Co and La-Co-Cu-Mg alloys were fabricated by powder metallurgy techniques and evaluated. A maximum intrinsic coercivity of 23.2 kOe was obtained with a La-Co-Cu-Mg alloy. In comparison, maximum values of 9.3 kOe and 11.6 kOe were obtained with La-Co and La-Co-Cu alloys, respectively. The substitution of copper and magnesium for part of the cobalt resulted in a large increase of intrinsic coercivity, similar to the results of Bureau research with mischmetal-Co-Cu-Mg alloys. Unlike the mischmetal-Co-Cu-Mg magnets, the La-Co-Cu-Mg magnets showed signs of physical deterioration on exposure to air. The effects of fabrication parameters on the magnetic properties of the La-Co-Cu-Mg alloys were also determined.

Jan 1, 1982

By Isaac A. Zlochower, Kenneth L. Cashdollar

The Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health conducted a study of the explosibility of various metals and other elemental dusts dispersed in air, with a focus on the experimental explosion temperatures. The data are useful for understanding the basics of dust cloud combustion, as well as for evaluating the explosion hazards in the minerals and metals processing industries. The dusts studied included boron, carbon, magnesium, aluminum, silicon, sulfur, titanium, chromium, iron, nickel, copper, zinc, niobium, molybdenum, tin, hafhium, tantalum, tungsten, and lead. The dusts were chosen to cover a wide range of physical properties - from the more volatile materials such as magnesium, aluminum, sulfur, and zinc to the highly "refractory" (very low volatility) elements such as carbon, niobium, molybdenum, tantalum, and tungsten. These flammability studies were conducted in a 20-L chamber, using strong pyrotechc ignitors. The experimental data obtained included the minimum explosible concentrations, maximum explosion pressures, and maximum explosion temperatures. A unique multiwavelength infrared pyrometer was used to measure the temperatures. For the elemental dusts studied, all ignited and burned as air-dispersed dust clouds except for nickel, copper, molybdenum, and lead. The measured maximum explosion temperatures ranged from -1 550 K for tin and tungsten powders to -2800 K for aluminum, magnesium, and titanium powders. The measured temperatures are compared to the calculated, adiabatic flame temperatures. In general, the dusts whose experimental temperatures were closer to the adiabatic values were those with the finer particle sizes, those that were more easily vaporized, and/or those that were intrinsically more reactive.

By Allen L. Frank

A portable radon diffusion chamber has been tested with electrical collection of the radon daughter nuclei for enhancement of sensitivity. The detector size was small enough to be worn suspended from the belt. With a battery-supplied high voltage the sensitivity was found to be 1.43 tracks/cm2 per pCi-hr/l of ambient radon at Sot relative humidity. The track densities on the surfaces of the CR-39 plastic nuclear track detectors were found to be non-uniform, making difficult the determination of average densities with high accuracy. The fabrication of electrets for use in the detector was investigated in accordance with published techniques with negative results.

Jan 1, 1983

By Robert C. Gabler

The extraction of metals from coal ash was investigated by the Bureau of Mines in an effort to produce a more environmentally acceptable waste and offset waste disposal costs with recovered metal values. The research was conducted in two steps: determination of the parameters that affect extraction of metals from coal ash and development of extraction-recovery procedures. Data obtained indicate that the major parameter affecting the extraction of metals from coal ash is the calcium content of the ash. Other parameters such as furnace type and operating temperature had much smaller effects on metal extraction. Two procedures were studied for metal extraction: an acid leach procedure for high-calcium ashes and a lime sinter-acid leach procedure for low-calcium ashes. An alumina product was recovered that, with sufficient washing, meets Hall cell specifications. The leach residues pass the EPA EP Toxicity Test and are thus nonhazardous wastes available for a variety of uses.

Jan 1, 1983

By George S. Koch

A statistical analysis of silver assay data from rotary-drill-hole cut-tings and diamond-drill-hole cores from the Round Mountain prospect, Custer County, Colo., demonstrates several useful methods for estimating grades and tonnages of ore from the drilling of wide-spaced holes in disseminated deposits of precious metals. A new method of are appraisal is introduced which estimates grade and tonnage of are by calculating convex hulls (smallest convex polygons) for sample points with assay values above specified cutoff grades. Analyses of variance compare the consistency of data from rotary-and diamond-drill holes, from rotary-drill holes sampled at 2-and 4-foot intervals, from two methods of sample preparation, and from atomic-absorption and fire assaying. Evidently, data from the two types of drill holes, from holes sampled at the two intervals, and from different methods of preparation are in agreement. Atomic-absorption silver values are consistently lower than fire-assay silver values.

Jan 1, 1971

By Clarence O. Babcock

This Bureau of Mines report presents the initial development of a two-dimensional method of analysis for inclusions in plates in which the deformed shape of an open hole and the separate structural behavior of inclusion and plate with hole are used to obtain the stresses and strains in the inclusion only. In this report the solution for a circular inclusion is presented because a direct verification of the results with previous solutions was possible. The numerical results were in exact agreement with those obtained with the equations of Sezawa and Donnell. The equations developed are less complex than those of Sezawa and more general, for a circular inclusion, than those of Donnell. Stresses and strains in the inclusion are in terms of the elastic constants of the inclusion and the plate and the biaxial stress field applied far away. The elastic constants can be all different. An important conclusion from this work is that a difference in Poisson's ratios between inclusion and plate may be as important as a difference in Young's moduli between inclusion and plate in producing the inclusion effect. Many problems in mining and rock mechanics can be treated as inclusion problems. The understanding of inclusion behavior on a physical basis should provide the solutions to some of these problems.

Jan 1, 1974

By Charles L. Kimbell

Annual global steel industry investment is partly mirrored in the data for selected market economy countries that appear in table 13 for 1988-90. No reasonably comprehensive 1991 data were available for inclusion in this study, and the partial reporting available was so incomplete that it was impossible to demonstrate whether the level advanced or declined from the 1990 level of nearly $15.5 billion. Moreover, with the radical changes that are now being effected in the steel industries of the states that were the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available. Updated information on market economy country petroleum industry capital and exploration expenditures by geographic area has been included in table 14, and it is evident that there was a substantial upturn in investment in 1991. The level of almost $74.5 billion was 14.5 % above the 1990 level and included gains in every topical category and geographic area. The source of information for this table has been changed to the Oil and Gas Journal Database from the previously used Chase-Manhattan Bank study of Capital Investments of the World Petroleum Industry, which has been discontinued. Because of this source change, it has been necessary to modify the structure of the table somewhat, but its total scope of coverage is regarded as basically unchanged. It should be noted that the grand total, as well as some of the detail appearing for 1987, corresponds precisely with those in the previous source.

Jan 1, 1993

By W. K. Sawyer

In this Bureau of Mines investigation, one-and two-dimensional gas reservoir simulators were combined in such a manner that pressure distributions both in an induced vertical fracture and in the surrounding formation, could be determined as a function of time for any specified well production rate. The technique used consisted basically of the alternate ust of one-and two-dimensional algorithms for obtaining new pressure distributions in the fracture and in the reservoir, respectively. The pressures at adjacent reservoir and fracture nodes were used to calculate flow rates from the formation into the fracture, which provided source terms for both algorithms. The combination model developed provides the only known means of simultaneously simulating transient gas flow in a vertical fracture and the surrounding formation. Thus, the technique developed would be useful in locating wells in a gas storage field in that the effects of both fracture length and conductivity could be considered prior to drilling and fracturing operations. In addition, it will be helpful in analyzing pressure drawdown tests in a vertically fractured gas well since the entire test can be readily simulated for a wide range of reservoir and fracture properties.

Jan 1, 1974

By R. V. Ramani, K. V. K. Prasad

"Solution of most engineering problems requires, in addition to vast ·numerical calculations, substantial use of practical judgement and expertise. With advances in applied mathematics and computer technology, the numerical aspects of problem solution have reached a considerable level of maturity; However; it is only .recently that approaches like the expert systems methodology have been developed to ·incorporate the Judgemental aspects as well. For rapid development and prototying of expert systems, expert system building tools or ""shells"" have become widely available. For the expert system developer, identification of the key characteristics of the problem domain and selection of the right expert system tool are of crucial importance. In this paper, the important attributes required in an expert system shell for use in the development or a mine ventilation planning expert system are discussed. These attributes are general in that most engineering problems in mining would have these requirements. Also, the results of an exercise undertaken to evaluate commercially available shells for application to mining engineering problems are presented.INRODUCTIONExpert systems (ES) are interactive computer programs which use high quality specialized knowledge in some narrow problem domain to solve complex problems in that domain. These complex problems lack structured and/or standard ways of solution and involve substantial use of subjective and experience based knowledge. One of the first expert systems was MYCIN, developed in 1974, in which subjective and heuristic knowledge of expert physicians was used to diagnose infectious diseases and provide antimicrobial therapy (Buchanan arid Shortliffe, 1984). Since MYCIN, expert systems applications have appeared in other areas such as mineral prospecting (Gaschnig, 1982), configuration of computers (McDermott, 1982) and structural engineering (Bennett and Englemore, 1979)."

Jan 1, 1989

By B. Dimitriades

Experimental work has been done to refine and to confirm an analytical procedure by which gas-liquid chromatographic (GLC) spectra are interpreted from retention time data alone. The rationale of this spectra interpretation technique involves whether or not a given peak invariably represents the same component or component mixture; if not, what factors influence changes in peak identifications. To answer these questions, peak-identification procedures, based mainly on the use of subtractive columns, were developed and applied to interpret GLC spectra of several exhaust (and fuel) samples.

Jan 1, 1972