Search Documents

By Walter T. Ackley

[The geophone has occupied a prominent position as a mine signalling device since its first introduction. The Bureau has carried out tests at different times with a view to improving the early geophones. The following paper describes briefly the adaption of the vacuum-tube audio frequency Amplifier to a new form of geophone. It is not intended to convey the idea that the results described are sufficient to warrant the drawing of definite conclusions as to the practicability of the electrical geophone, but the data and tests liven herein are made public because of their possible use to the industry and as a result of inquiries received as to the feasibility of such adaptions and modifications of the early geophones. Because of the limited time available to the authors, only one geophone with its auxiliary amplifier was constructed. As is well known, two geophones are necessary in order to determine the direction of a sound. Although the principles upon which the electrical geophone operates appear to be fundamentally correct, it is not possible to state whether two such devices 'rill function as efficiently, (as regards determining direction of sound) as the present geophone. In order to operate efficiently as a direction finder, the amplifiers of the electrical geophone must each amplify with exactly the same degree of magnitude. By proper design and adjustment this can probably be accomplished without greatly complicating the design. inasmuch as audio frequency amplification is used, no tuning; is necessary as is the case with tuned radio-frequency circuits. The same filament and plate batteries can be used to operate the amplifiers and by the use of dry cell tubes, requiring shall filament and plate currents, it if believed that a compact, portable and practical instrument can be evolved. Further investigations of the electrical geophone should be conducted to determine the points outlined in this preliminary report.]

Jan 1, 1924

By G. K. Derby

The Bureau of Mines studied the problems caused by airborne contaminants from welding exhaust in surface mining operations and investigated equipment designed to reduce existing hazards. Four commercially available welding-fume exhaust units were tested to determine their effectiveness. Results indicated that the four units had the capability of controlling airborne particulate concentrations and bringing them to within allowable exposure limits.

Jan 1, 1981

By Je M. Oh

The Bureau of Mines is conducting research to determine the high temperature oxidation resistance of substitute stainless steels (SS) containing two less strategic elements, Al and Si, instead of Cr. Chromium is considered to be a critical and strategic metal. Although the Cr content was reduced to 8 wt pct, the alloys showed better oxidation resistance than did 304 SS containing 18 wt pct Cr. Specifically, the alloys that contained Fe-8Cr-16Ni with combinations of Al and Si showed excellent oxidation resistance even at temperatures up to 1,000° C. In this study, the effects of the alloying elements on oxidation kinetics and morphology of oxides were investigated using a Cahn Rg electrobalance, scanning electron microscopy, an energy-dispersive X-ray analyzer, X-ray diffraction, and an electron microprobe. Aluminum and silicon additions in combinatin were more effective in providing oxidation resistance than either element was alone.

Jan 1, 1986

By John Henderson

If you missed this year?s Texas State Holmes Safety Association meeting, you missed a great one. On January 23 & 24, 2009, we held the meeting that was rescheduled when Hurricane Ike threatened Corpus Christi in September 2008. Sixty-five persons from across the state attended the meeting held at the Holiday Inn Emerald Beach. The weather was 82 degrees, and the sky was clear and perfect for a safety meeting. Evaluations submitted by the attendees gave the presentations, the networking, and even the food top marks. There were eight councils represented; Big Country, Central Texas, Costal Bend, Heart of Texas, Hill Country, North Texas and North Central. Presentations included Workplace Examinations, Emergency Preparedness, Screen Safety, Contractor Responsibilities, Powered Haulage, Supervising for Safety, and Basic Inspections of Slings and Rigging. Mr. Edward Lopez, SC MSHA District Manager, gave the State of the District Address.

Jan 1, 2009

By D. S. Kingery

The practice of using doors to control main ventilating currents in bituminous-coal mines is common throughout the industry. When doors are erected in pairs to form air locks, they are usually accepted as satisfactory by both State and Federal coal-mine-inspection agencies. A review of the contributing factors in recent methane ignitions showed that interrupted ventilation (often caused by doors latched open, destroyed, or damaged) was the principal cause of methane accumulations that subsequently were ignited.

Jan 1, 1958

By J. Davitt McAteer

Dear Mine Operator, Training for new employees, refresher training for new employees, refresher training, and new task training can mean the difference between life and death for workers. Part 46 spells out how you can develop a training program to protect workers for on-the-job hazards. Together, labor, industry, and the U.S. Department of Labor reached a milestone with the development and publication of Part 46. We want to continue working together toward the next milestone, October 2000, when the regulations take effect. We want to make sure you have all the information you need about these new training requirements. Throughout the next 12 months, MSHA personnel will be holding regional meetings across the country, delivering information and sample training plans to your operation, and offering you help to develop your plan. If you are among the many operators who are already providing training to your workers, keep up the good work. The rule will tell you exactly what is expected. If you currently have no training program, we can help you develop one. A brochure is being distributed, which highlights the main provisions of the rule. It is designed to introduce the rule to you. More detailed materials will be delivered to you. If you want information right away, simply call us, or e-mail us. We also welcome your comments, suggestions, and success stories. Part 46 will be successful and beneficial to miners through our combined efforts. Together, we can make our mines safe and healthier for everyone. Sincerely, J. Davitt McAteer, Assistant Secretary of Labor Mine Safety and Health Administration

Jan 1, 1999

By T. O. Llewellyn

The Bureau of Mines, as part of its goal to develop technology that can conserve domestic mineral resources investigated beneficiation methods for recovering phosphate minerals from two Southern Florida deposits with high magnesium content. Chemical analyses of sized fractions indicated that no coarse pebble concentrate could be produced from either deposit. Conventional fatty acid-fuel oil batch flotation tests on two phosphate samples, analyzing 6.8 and 8.5 pct P205, yielded concentrates containing 28.97 to 29.80 pct P20S at recoveries ranging from 72.4 to 76.9 pct of the flotation feed. The MgO content ranged from 1.20 to 1.36 pct. Bubbling S02 gas through an aqueous concentrate slurry, further reduced the MgO content of these phosphate concentrates to 0.5 and 0.8 pct, but with a concomitant loss in the phosphate recovery. Settling characteristics of slimes from both phosphate samples showed a slow settling rate, which is a typical characteristic of other slimes in the region.

Jan 1, 1981

By David A. Benjamin

In 1989 and 1990, the Bureau of Mines conducted a mineral resource investigation of the 122,000-acre Trinities study area, located in the Trinity Mountains of south-central Idaho. No identified mineral resources were delineated during this study. There are 58 lode mining claims within the area. Five localities contained elevated metal concentrations which may indicate precious metal mineralization at four localities and molybdenum-precious metal mineralization at another. Four of the five localities appear to form a northwest trend through the center of the study area. Twenty-eight individual sites contain anomalous concentrations of gold, silver, bismuth, molybdenum, and beryllium.

Jan 1, 1991

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979

By D. J. Bauer

Solvent extraction techniques were used to determine the extraction sequence of yttrium and the rare-earth elements in an amine solvent extraction system. Single-stage extraction with Primene 81-R resulted in separation factors of 3.8 between yttrium and dysprosium and 25 between yttrium and cerium. Yttrium was concentrated in the aqueous phase. EDTA and DTPA, as aqueous phase counterextractants, enhance separation factors in mine-rare-earth sulfate systems. Yttrium separation from heavy rare-earth elements exhibits marked sensitivity to the position of yttrium in the selectivity scale of the rare-earth elements with the sequestrants. Yttrium-ytterbium separation is more effective with EDTA, whereas yttrium-dysprosium separation is more effectively increased with DTPA.

Jan 1, 1963

By H. H. Schrenk

The Bureau of Mines midget impinger dust-sampling apparatus was described first in 1937.4/ Two supplementary reports5/6 were published in 1938. These reports are now out of print. The material published previously is combined in this paper to make information on this device available for distribution. The impinger was developed by the Bureau of Mines in cooperation with the United States Public Health Service in 1922. The underlying principle of this instruments is based on impingement land wetting, of the dust particles by drawing air through a nozzle at high velocity onto a smooth surface under a bubbling column of liquid. The dust particles are retained in the liquid. The apparatus has been used widely and permissible limits of dustiness have teen established in the United States on the basis of results obtained with this device in correlation with medical studies. However, it has been criticized for its bulk, weight, and power requirements.

Jan 1, 1939

By James H. Scott

A technique of seismic refraction data analysis has been developed in which a digital computer is used to generate a two-dimensional model representing a layered-earth depth interpretation. Travel times are picked on seismic records by the human interpreter. These times, together with shot point and geophone locations and refraction layer control information, are submitted to the computer on punched cards. A first approximation delineation of each refraction horizon is obtained by a computer adaptation of the delay-time method. The approximation is then tested and improved by the computer through the use of a ray-tracing procedure in which ray travel times computed for the model are compared against field-measured travel times. The model is subsequently adjusted in an iterative manner so as to minimize the discrepancy between computed and measured travel times. The Fortran program is listed in the appendix of the report together with instructions for preparing data cards and examples of results.

Jan 1, 1972

By Christopher C. Jobes, Alan G. Mayton, Farid Amirouche

Based on prior mine vehicle studies of operators’ exposure to whole-body vibration, researchers from the National Institute for Occupational Safety and Health (NIOSH) evaluated four seat designs on mine haulage vehicles, with regard to roadway-induced jarring/jolting and operator comfort. Investigators collected objective and subjective data from vehicle operators on two existing and two NIOSH seat designs. This study included time and frequency response data using accelerometers and a data recorder, operator perceptions of jarring/jolting and discomfort levels using a linear visual analogue scale, and data from a questionnaire developed for this study. Results from the analysis of subjective data show that operators generally favoured the NIOSH-designed seats over the existing seats. The results of analyses from the absorbed power method and the threshold limit method, based on ISO 2631-1 (ISO, 1985), support the premise that NIOSH seat designs are superior to the existing vehicle seat designs on both models of mine shuttle cars used in the study. The NIOSH seat designs, featuring viscoelastic foam padding, were more effective in reducing vibration energy for operators exposed to vehicle jarring/jolting. In this paper, the performances of the NIOSH and existing seat designs are compared relative to the operator’s exposure to vehicle vibration (mainly jarring/jolting).

By H. V. Makar

A study was conducted by the Bureau of Mines to determine problems associated with the use of ferrous fractions from urban refuse as melting stock for steelmaking and to evaluate the resulting steel products. The study involved 50-pound ingots from laboratory melts and 50-pound ingots from 1-ton electric-arc-furnace melts. The 50 pound ingots from the laboratory melts and the arc-furnace melts were hot rolled to provide material for mechanical and corrosion testing. Results obtained in the study include the following: Most steels rolled successfully and exhibited acceptable surface and edge condition. Tensile strengths of the plain carbon steels were not significantly affected by copper up to concentrations of 0.65 pct and were not affected by tin content up to 0.16 pct. Yield strength increased with increasing copper and tin contents, and impact strength decreased with increasing tin content. Hardness increased slightly with increasing copper content. In general, properties of the steel produced were not measurably affected by charge composition (that is, melting stock), melting practice, or method of scrap preparation.

Jan 1, 1975

By John Durkin

Owing to the daily exposures of uranium mining personnel to 222Rn daughters, a device is needed that will continually monitor individual exposure. Such a device has been built and tested by the Bureau of Mines and is known as a radon daughter dosimeter. This is an electronic instrument using a solid-state detector and circuitry. The concept of the instrument, which is a personal device worn throughout the working shift, is to evaluate an individual's cumulative exposure to airborne radon progeny, expressed in units of working level hours. Since the instrument is in close proximity to the miner and measures continual exposure, it avoids the errors caused by the present technique of spot checking of the environment and provides a more accurate account of total cumulative exposure.

Jan 1, 1977

By Howard C. Turnage, Dana T. Updyke

An evaluation was made of one of several improved underground communication systems sponsored by the U.S. Bureau of Mines. The system evaluated was installed in a typical metal/non-metal room and pillar mine and utilized UHF repeaters connected to a unique distributed antenna and passive reflector system which provided mine-wide communications. A microprocessor controlled data collection system was assembled and installed for the evaluation. Data consisting principally of times and durations of messages and identities of the originating transceivers was collected between February and August of 1982 (6 mos.). Analysis of the data shows that the principal benefits are reduction in time required for unscheduled maintenance and repair, enhancement of safety, and better coordination of production activities. A cost benefit analysis shows a net benefit over cost, although it is also concluded that the capacity of the system is greater than can be justified by current activity in the mine.

Jan 2, 1983

By R. E. Collom

The spontaneous explosion of charges of nitroglycerin placed in deep wells situated in parts of the Ranger and Caddo fields of North Texas has aroused considerable inquiry among operators end others as to the probable agency, or combination of conditions, which causes the explosion.The method now followed, under certain physical conditions of a well, of setting a charge of nitroglycerin and allowing it to explode spontaneously was discovered locally by accident. In certain deep wells where formations, overlying productive strata, cave upon withdrawal of casing, it has been the practice to fire the shot electrically. In some of these operations the electric wires are broken or the firing system is otherwise deranged by pulling casing or the caving of hole prior to the time for firing. Sucn accidents make it necessary for the driller carefully to clean cavings out of the hole to a depth close to the top of the charge, after which in the normal practice, an attempt is made to fire the charge by dropping a ""jack-squib"", fitted with a fuse and detonator, down the well. Mr. R. L, Fowler, production manager for the Pierce Oil Corporation, reports that a delayed shot was thus successfully tired through four feet of caved material lying on top of the nitroglycerin shells.When a shot destined to be fired electrically fails, because of the above mentioned accidental conditions to the electric firing system, much time is required for the driller to run casing into the hole and clean out caved material. It was during the time of such uncompleted operations that the spontaneous explosions first noted took place. Having noted these spontaneous explosions the well shooters now intentionally place a charge in deep holes, which because of probable caves would otherwise have to be tired electrically, and wait for the charge to go off. No detonators are placed with the charge.

May 1, 1920

By John A. Breslin

Three scale models of coal mine entries and mining machines were constructed by the Bureau of Mines to study the effects of ventilation parameters on dust concentrations where mining personnel would be working. A one-fifth-scale model of a coal mine entry with a drum-type continuous-mining machine and a one-sixth-scale model of an entry with a twin-borer-type machine were used as well as a one-fifth-scale model of a longwall face with a double-drum shearer. Methane was used as a tracer gas to simulate respirable dust in the models. The distance of the end of the brattice or tubing from the face was found to be more important than the airflow rate for the drum-type machine. Dust reductions greater than 90 pct were shown to be possible with a secondary ventilation system used with the twin borer and a dust collector mounted on the longwall shearer. Cutting-head speed had a significant effect on concentrations at typical positions of miners with the drum-type machine and longwall shearer but not for the twin borer.

Jan 1, 1976

By B. H. Eccleston

Experimental work is reported showing the effects of gasoline characteristics on auto emissions. Fuel volatility is shown to influence evaporative losses, with the higher losses associated with higher volatility. Fuel front-end olefin is shown to contribute significantly to reactivity of emissions. Large vehicle-to-vehicle differences were found. The study was conducted by the Bureau of Mines at its Bartlesville Energy Research Center in cooperation with the Coordinating Research Council Air Pollution Research Advisory Committee. The work was done using 15 1968-70 model autos and eight fuels were tested at ambients ranging from 20° to 95° F. Data on emissions from each vehicle-fuel-temperature combination are presented. Also included are calculated photochemical reactivity data and the distribution of hydrocarbon and nitrogen oxides during the test cycle.

Jan 1, 1972

By G. W. Jones, R. E. Kennedy

"INTRODUCTION Information relative to the ignition temperatures of acetylene and acetylene-air mixtures has become of particular interest recently due to a number of explosions that have occurred in 500-pound, double-rated, medium-pressure acetylene generators in shipyards on the West coast. Various suggestions have been made as to the causes of these explosions prominent among which has been that air finds its way into the acetylene generators during abnormal operation or that air remains in the carbide hopper of the generator following the purging and charging operations.This raises the question as to how and to what extent the presence of small percentages of air in acetylene affects the ease of ignition of such mixtures at the various operating pressures of the acetylene generators. The range of operating pressures in the 500-pound, double-rated generators involved in the explosions may vary from below atmospheric to 15 pounds gage.The present report gives the results of an investigation made to determine the effects of pressure on the ignition temperature of pure acetylene and of acetylene containing varying percentages of air:EXPERIMENTAL Apparatus A preliminary investigation showed that a heated quartz surface gave lower ignition temperatures than other material tested.A ""hot-spot"" method of ignition was found desirable in the case of the acetylene mixtures since the violence of the explosions was reduced by keeping most of the test mixtures at room temperature. Explosive violence was reduced further by using an ignition tube 17 mm. or less in diameter."

Mar 1, 1945