Search Documents

By Seymour Wasserman

To develop noise control designs for secondary crushers in Taconite plants. Taken into consideration: 1. Acoustical criteria 2. Day-to-day operational considerations and maintenance accessibility 3. Materials of construction 4. Adaptability of design to other Taconite plants having crushers 5. Cost of noise control treatment.

Jan 1, 1977

By T. T. Campbell

This report describes the development of new electroplating baths from which tin-nickel alloy plate was deposited. Although tin-nickel plate can be deposited from an aqueous ammonium bifluoride bath, the corrosive nature of this bath has served as a deterrent to its use. The Bureau of Mines felt that more general acceptance of this new alloy plate would follow if neutral or alkaline baths could be developed. Promising results were obtained from electrolytes containing both tin and nickel chlorides dissolved in triethanolamine-hydrochloric acid or in ethylene glycol hydrochloric acid baths. Current efficiencies close to 100 percent were obtained with these baths. Research revealed that tin-nickel plate could be produced from organic solvents or from mixed aqueous-organic electrolytes. The composition of the alloy deposit - 65 percent tin and 35 percent nickel - was found to exhibit the same single-phase structure that is obtained from the commercially accepted fluoride-type bath.

Jan 1, 1959

By R. D. Leitch

The pollution of streams by acid mine drainage has become of great importance in the past few years in certain regions of the United States. Large quantities of acids are used in a discharged from other industries than mining, notably in tube, sheet, tin-plate and era hell inn works. These are usually less important then coal mines as a source of acid drainage, because of their more limited distribution throughout the States most affected by acid waters and their relatively smaller numbers. Streams are naturally alkaline and are, therefore, able to take care of rather large quantities of acid wastes, but when such enormous quantities as are often found in mining districts enter the streams, the natural alkalinity is quickly overcome. When a neutral or almost neutral condition has been reached, the further addition of a relatively slight quantity of acids will cause a great difference in the quality of the water.

Jan 1, 1926

By A. Gene Collins

The Bureau of Mines conducted a research study of the geochemistry of the Smackover Formation to determine what geochemical relationships are useful in exploration for and production of oil and gas. Samples of oil, gas, brine, and rock were collected and analyzed. The oilfied brines were analyzed by methods recommended by the American Petroleum Institute and by tentative methods of the American Society for Testing and Materials. The crude oils were analyzed by Bureau of Mines methods; the gas, by Bureau of Mines methods; and the rocks, by wet-chemical, atomic absorption, and neutron activation methods. The results were correlated and interpreted, and several geochemical relationships useful in exploration and production were found. These include the type and class of brine, organic constituents in the brine, redox potential, in situ temperature and pressure of brine, degree of sulfate and carbonate saturation of brine, and halide concentrations in the brine.

Jan 1, 1974

By J. B. Littlefield

This study is one of a number conducted to determine the concentration of dust in the air during the complete cycle of operation in wet drilling information as to various factors connected with drilling in mining operations is considered to be of definite value in the control and prevention of air dustiness, and it is particularly desirable to ascertain What features of present-day wet-drilling operations in mine work contribute to dust disease and to remedy deficiencies when they are found. ACKNOWLEDGMENTS A testing alit through rock strata is being developed by the Mining Division of the United States bureau of Mines at Mount Weather, Va., and the tests discussed in this report were conducted there. This experimental alit in rock, constitutes a typo of laboratory where mine conditions can be closely simulated and where many of the variables likely to occur in an actual mine can be eliminated or at least controlled with reasonable effort, thus affording maximum opportunities to secure fundamental data uncomplicated by extraneous conditions. The authors wish to acknowledge the valuable assistance and cooperation of several members of the Mining Division, particularly C. F. Jackson, chief engineer, McHenry Mosier, associate mining engineer, and G. E. McElroy, supervising engineer, mine ventilation.

Jan 1, 1938

By Charles L. Kimbell

The estimated value of world crude mineral production in 1990 exceeded $1,501.5 billion in terms of current (1990) dollars, or almost $1,160 billion in terms of constant 1983 dollars. This latter figure was 0.3% below the 1989 level and about 3.9% below the record high to date of $1,207.1 billion 1983 dollars set in 1980. Table 1 provides the latest available revised time series of the estimated value of world crude mineral production both in terms of 1983 constant dollars and in terms of current dollars. It also provides one of the two statistical bases for this estimation, this being the data on the value of production of a group of key commodities that was compiled for and published in the authoritative French language mineral industry periodical, Annales des Mines, for selected years up to 1983.1 It should be stressed that the values just discussed and those presented in the tabulation are for crude minerals only, and by no means reflect adequately the role of the entire mineral industry in the world economy. These figures represent only the value of mineral materials as they are mined or otherwise extracted from the earth. They do not reflect the value added to these materials through downstream processing within the facilities commonly accepted as mineral industry plants. That is, value added through beneficiation of ores, smelting, refining, and similar processing is not included in these figures. Comprehensive world data on the value added by such processing are not available; however, a conservative estimate of the total value of pro-cessed output from mineral industry plants derived wholly from primary (newly mined) materials would be on the order of about $2,780 billion constant 1983 dollars or $3,600 billion in terms of 1990 dollars.

Jan 1, 1993

By Paul M. Tyler

Graphite is chemically identical with diamond, both being crystallized allotropic forms of carbon. Graphite obviously differs greatly from diamond in physical properties and is easily recognized by its blackness, its softness (1 to 2 on Mohs' scale), and its slick feel when rubbed between the fingers. Strictly speaking, all graphite is crystalline, but grades in which the individual grains cannot be distinguished with the naked eye are commercially classed as amorphous. Natural mixtures of the two varieties occur in all proportions, and the classification of a given sample as "amorphous" or "crystalline" graphite is based largely upon trade practice. Until recently different varieties of vegetable or animal charcoal, lamp black, soot, gas carbon, and coal ware considered strictly amorphous, but modern examination by X-ray methods indicates that even these materials possess the same internal crystalline structure as graphite, differences in physical properties being perhaps explained by porosity or presence of combined hydrogen or other impurities.

Jan 1, 1941

By E. Morrice

High-purity lanthanum metal was prepared by electrolysis of La003 in a LaF3-LiF-BaF2 bath at 950° C. The requisite bath temperature for the deposition of molten metal was maintained by supplying the heat as current directly to the electrodes. A current efficiency of about 60 percent was obtained. The lanthanum nodules contained carbon and oxygen as major impurities. The total impurity content was from about 0.1 to 0.2 percent.

Jan 1, 1962

By Samuel P. Harteis, Eric S. Weiss

The National Mining Association and the Mine Safety and Health Administration requested that the National Institute for Occupational Safety and Health (NIOSH) conduct full-scale evaluations of a recently developed carbon fiber-reinforced polymer (CFRP) reinforcement technique for upgrading existing mine ventilation seals to withstand an explosion pressure of 50 psi or greater. The evaluation was conducted in the NIOSH Pittsburgh Research Laboratory’s Lake Lynn Experimental Mine (LLEM) near Fairchance, PA. The purpose of the evaluation was to determine the blast resistance of the CFRP reinforcement technique, designed to increase the strength of two types of existing 20-psi-rated in situ mine ventilation seals. Two candidate ventilation seals were selected to represent the 20-psi alternative seal designs typical of those used in mines prior to July 2006. Installed within the LLEM were (1) a 4-ft-thick pumpable cementitious foam seal using material with a designed 150- to 200-psi average compressive strength at 28 days and (2) a 24-in-thick, low-density cementitious block seal with a center pilaster and keyed to the floor and ribs. The materials necessary for the CFRP reinforcement technique were then installed on the outby (active) side of each seal, and the seals were subjected to explosion overpressures. Both seals with the CFRP reinforcement retrofit successfully withstood explosion pressures of 60 psi or greater during the full-scale evaluations in the LLEM.

Jan 1, 2008

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

Flexible hoses with rated working pressures up to 40,000 psi are used when high-pressure water jets are employed to cut rock or improve the performance of mining machines. Hose failures at such high pressures can result in serious injuries to workers. The Bureau of Mines used fatigue and burst tests to investigate the failure modes of high-pressure hoses at their rated working and burst pressures. Fatigue failure, at rated working pressures, occurred when the inner liner of the high-pressure hose broke, allowing water to seep through the wire wrapping, although the reinforcement wires did not break. At the burst pressure, all hoses failed catastrophically when the reinforcement wires broke. Low-pressure hoses placed over the high- pressure hoses for safety failed to contain water released by catastrophic failure.

Jan 1, 1987

By Edward L. McHugh, Jami M. Girard

While less than 1% of reported accidents are associated with slope stability problems, slope failures were responsible for about 15% of all U.S. surface mine fatalities between 1995 and 2001. Small rockfalls, which may involve hand-sized rocks weighing only a few kilograms, can cause fatal injuries to workers away from the protection of large machinery. Massive highwall failures containing a million cubic meters of material or more can be fatal even for heavy equipment operators. As part of an ongoing study at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health, several remote-sensing technologies are being evaluated as tools to monitor slopes for hazards and to assess slope stability. Field tests of a hyper spectral imager were conducted to assess its value for improving geologic maps of potentially unstable alteration zones on mine slopes. An interferometric radar device capable of detecting very small displacements on slopes awaits final assembly and field testing. Computerized monitoring methods using images from digital and video cameras are being assessed for application to mine slope surveillance. These and other techniques will eventually provide new tools to augment current methods for monitoring ground control hazards in mines.

By M. Kanda, W. D. Bensema, J. W. Adams

Two different techniques were used to make measurements of the absolute value of electromagnetic noise in an operating coal mine, Itmann No. 3 Mine, located near Mullens, West Virginia. The electromagnetic environment created by 250-volt-dc and 550- and 950-volt-ac machinery in two longwall panels was measured and is reported. One technique measures noise over the entire electromagnetic spectrum of interest for brief time periods. It is recorded using broadband analog magnetic tape, and the noise data is later transformed to give spectral plots. The other technique records noise amplitudes at several discrete frequencies for a sufficient amount of time to provide amplitude probability distributions. The specific, measured results are given in a number of spectral plots and amplitude probability distribution plots.

Jan 6, 1974

By H. E. Powell

The selective recovery of nickel and zinc from a waste phosphate solution by solvent extraction was investigated by the Bureau of Mines as part of a broad program to recover valuable metals and compounds from industrial wastes, and to reduce the associated land and water pollution caused by dumping these wastes. The waste, which resulted from the phosphation of automboile bodies, yielded 99 percent of both the nickel and the zinc by extraction with dinonyl naphthalene sulfonic acid (DNSA) and di-2-ethylhexyl phosphoric acid (EHPA), respectively. Dilute sulfuric acid was used to recover the metals and regenerate the solvents.

Jan 1, 1970

By A. J. Kraemer

The Bureau of Mines for a number of years has been carrying on an investigation of properties of crude petroleum from producing, fields in the United States and the Western Hemisphere, and has published a series of reports on these fields, including oil fields of Oklahoma2. Acknowledgements Thanks are due to R. R. Brandenthaler and Peter Grandone, of the Petroleum Experiment Station of the Bureau of Mines, at Bartlesville, Oklahoma, who reviewed the manuscript and contributed valuable suggestions. The samples were analyzed under the direction of E. C. Lane at the Bartlesville station of the Bureau of Mines.

Jan 1, 1927

By Hewitt Wilson

[ ]

Jan 1, 1927

By A. L. Engel

Many western ores containing ;old, silver, and copper can be mined and concentrated at a profit only when the recovery of those metals is high and treatment costs are low. Usually, ores containing easily dissolved copper minerals, or copper minerals that become soluble to some extent through oxidation during treatment, present a real problem in cyanidation. Copper cyanide compounds are formed that tend to 'precipitate and that cannot yield regenerated cyanide and metallic copper on contact with zinc. This results not only in some loss of copper through solution in cyanide, but in excessive consumption of cyanide above the amount required for the extraction of Gold and silver. Any moans, therefore, of minimizing the: loss of cyanide while at the same time effecting high recoveries of the several values contained in the ore is of wide interest. A sample of typical low-grade ore of gold, silver, and copper, containing copper-sulfide minerals, was obtained from the MacLaren Gold Mines Co., Cooke, Park County, Mont., for laboratory investigation by flotation and cyanidation.

Jan 1, 1950

By John C. Hartley

Three systems that monitor ventilating fans are described. These electronic monitoring systems automatically perform most of the operations required to conform with the provisions of the Federal Mine Safety Code in the event of fan failure or slowdown.

Jan 1, 1964

By D. R. Tesarik, R. W. McKibbin

Material properties affecting slope stability were measured in a large 50-year-old, partially consolidated rockdump located in an active open-pit mine. Field tests included single-ring infiltration and density. In addition, a nuclear depth-moisture gauge was used to measure water content in six stainless-steel-cased drill holes on the crest and an upper bench of the rock dump. Precipitation, evaporation, wind speed and direction, and temperature data were collected at a weather station installed on the dump’s crest. Laboratory tests included particle-size distribution, specific gravity, Atterberg limits, and water content. By measuring material properties of a rock dump presumed to be stable, the safety of miners working on or at the toe of old rock dumps constructed of similar material and located in a similar climate can be assessed.

Jan 1, 1999

By Lisa Steiner, Robin Burgess-Limerick

Working with or near underground coal mining equipment is hazardous because of the multiple sources of energy and adverse environmental conditions. Of the 4169 injuries reported to Coal Services during the three years to June 2005,447 were associated with continuous miners, 232 with LHD (load-haul- dump) vehicles, 140 with shuttle cars, and 140 with personnel transport - a total of 959, or 23% of all injuries reported during the period. An analysis of the injury narratives accompanying these injury claims highlights a number of opportunities for controlling injury risks. Using the frequency of reported injuries for the prioritisation of risk control strategies has limitations because of the tendency to underestimate the importance of relatively uncommon but potentially high consequence events. Injury reports also underestimate the contribution of risk factors such as whole body vibration, which have a long-term cumulative contribution to an elevated risk of injury. However, taking these limitations into consideration, the results of the injury narrative analysis suggests the following hazards as the highest priority for elimination or control: • handling continuous miner cable • strain while bolting • slipping off continuous miner platform • inadvertent or incorrect operation of bolting controls, and operation of controls while a person is in a position of danger • hitting potholes or other roadway abnormality • collisions while driving underground vehicles