Search Documents

By L. W. Brandt

Studies of liquid-vapor equilibria of gas mixtures at the Bureau of Mines Amarillo Helium Plant Laboratory require that the equilibrium cell be maintained uniformly at any desired temperature from approximately room temperature to -320° F. The temperature-control system must also tolerate a substantial heat input, in the form of warm gas flowing into the cell, without loss of control. Temperatures between the sublimation temperature of carbon dioxide (-109° F.) and the boiling point of liquid nitrogen (320° F.) are usually obtained by methods utilizing a hydrocarbon liquid bath cooled by liquid nitrogen.4/5/6/7/ Owing to the fire hazard attending such baths, a safer method of temperature control was desirable.

Jan 1, 1955

By L. H. Wullstein

Bureau of Mines research on methods for reclaiming land disturbed by the minerals sector of the economy has produced a specific procedure for effectively germinating seed of Indian ricegrass, a drought-tolerant plant valuable for reclaiming arid and semiarid sites. This report describes the procedure which consists of acid-treating the seed followed by temperature and light cycling treatments. Use of the procedure resulted in an average germination rate of 29 percent, ranging from 18 to 56 percent. Seed subjected to long cold treatment but with acid treatment yielded an average germination rate of 9.2 percent, ranging from 6.6 to 14.7 percent. Untreated seeds (controls) gave germination rates less than 0.1 percent.

Jan 1, 1979

By E. G. King

This paper reports measurements of low-temperature heat capacities and entropies at 298.15° K. of two copper ferrites (CUFe204 and CU0.75Fe2.2504). These substances, which occur in copper-smelting slags, have not been sujected to any previous direct thermodynamic investigation. The two copper ferrites are spinel minerals of the variate class. In previous investigations similar data were obtained for 13 other spinel minerals -7 of the normal class and 6 of the variate class. The entropies at 298.15° K. of these minerals have been compiled and revised as necessary in the light of present knowledge regarding structural randomness; entropy values, recommended for use in thermodynamic calculations, are listed.

Jan 1, 1959

By L. H. Adami

Heats of formation were obtained for four anhydrous crystalline sodium borates by hydrochloric acid solution calorimetry. The heats of formation at 298.15° K from the elements are NAB02, -233.2 ±0.6 kcal/mole; Na2B07, -786.4 ±1.0 kcal/mole; NaB305, -549.9 ±0.8 kcal/mole; and Na2B6013, -1,412.5 ±2.0 kcal/mole, The heats of formation from the constituent oxides are NaB02, -31.5 ±0.8 kcal/mole; Na2B407, -78.8 ±1.3 kcal/mole; NaB305, -44.1 ±0.8 kcal/mole; and Na2B8013, -96.7 ±1.5 kcal/mole.

Jan 1, 1968

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 11 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY, PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2, 1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AFCUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11, 1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS OF THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

1 9 THIS IS A DIGITAL COMPUTER SIMULATION OF THE VENTILATION SYSTEM OF A MINE LOCATED IN WASHINGTON COUNTY; PENNSYLVANIA. THE VENTILATION SURVEY ON WHICH THIS SIMULATION IS BASED WAS RUN FROM OCT. 27-30 AND ON NOV. 2;1976 IN THE ACTIVE PORTION OF THE MINE INBY COMBS SHAFT AND THE INACTIVE PORTION AROUND AND INBY DONAHOO SHAFT. FOLLOW-UP SURVEYS WERE THEN RUN ON FEB. 18 AND FROM MARCH 7-11;1977 TO INCLUDE THE MAIN HAULAGE SYSTEM OUTBY THE ACTIVE AREAS 0F THE MINE. ALL SURVEY DATA WAS NORMALIZED TO A STANDARD DENSITY OF 0.075 POUNDS/CU.FT. PRIOR TO THE CALCULATION OF INPUT PARAMETERS FOR THIS SIMULATION.

Jan 1, 1977

By Terry S. Cory

This report is a comprehensive summary of the results of the propagation measurements program conducted for the US Bureau of Mines under Contract H0366028. Data was gathered in the MF frequency range from a cross sample of six mines representative of the industry having typical wireless requirements. From the raw data which was gathered, a logical method of data reduction is presented which culminates in a set of average attenuation characteristics for all mines visited. These characteristics define a typical MF wireless system when the communication range requirements are known. Direct through-the-earth propagation and the range enhancement mechanism due to coupling on and off conductors are evaluated and related to the planning of a typical wireless MF communications system.

Jan 8, 1977

By C. P. Lazzara, Y. Miron, A. C. Smith

This report presents a U.S. Bureau of Mines study to identify the causes of self-heating events beneath the floor of a deep underground coal mine. Mine samples from both heated and unheated areas were examined by various techniques, including visual, microscopic, thermal, chemical, and instrumental tests. The combined results led to the conclusion that pyrite (FeS2) oxidation was the prime cause of the beatings. However, adiabatic oven tests of selected samples did not indicate the effect of the pyrite on the self-heating process, probably because of the experimental conditions. A fast, simple procedure to assess the concentration of pyrite in the mine samples was developed, utilizing the reactivity of the sample with an aqueous solution of hydrogen peroxide (H2O2)

Jan 1, 1992

By Ann G. Kim

Gas samples containing 02, N2, H2, He, CO2, CO, CH4, and trace amounts of C 2 to C6 hydrocarbons are analyzed by a gas chromatographic method that utilizes both thermal conductivity and flame ionization detectors. A porous polymer support and molecular sieve columns are used with argon as the carrier gas. A column selector valve makes it possible to perform a complete analysis either on one 1-ml sample in 40 minutes or on two samples in 20 minutes, one sample for each detector. Samples are introduced either by on-column injection or through a gas sampling valve. By varying operational parameters, the speed, sensitivity, and accuracy of analysis may be modified to suit a particular situation.

Jan 1, 1974

By Charles Anema

The Mancarried and Helicopter Receivers were developed under the contract I for trapped miner location. This program was a five phase program with 15 mancarried and 5 helicopter production receivers delivered under Phase IV and equipment documentation required under Phase V.

Jan 11, 1976

To determine the effectiveness of multiple types of fire sensors for early and reliable mine fire detection. Background The National Institute for Occupational Safety and Health (NIOSH) has evaluated the effectiveness of multiple types of fire sensors for early mine fire detection and nuisance signal discrimination. Reliable early fire detection in underground mine can be hindered by false fire alarms produced by carbon monoxide (CO) and smoke particulate emissions from diesel equipment, welding, and metal-burning activities. Another false fire alarm source is the cross-interference of hydrogen (H2) produced by battery-charging operations with a CO sensor's chemical cell. Workers can learn to ignore repetitious "false" alarms associated with these emissions. This jeopardizes their safety in the event of a mine fire.

Sep 1, 2002

By John Nagy, Austin R. Cooper

Information is presented on the pressure and rate of pressure development during a dust explosion . The data were obtained in laboratory studies in a 75- cubic inch vessel with mineral , agricultural and chemical dusts . The factors investigated include dust concentration , oxygen concentration of the atmosphere , admixed inert powder , and admixed moisture . Information is given also on the effects of these factors on the composition of the atmosphere after the explosion .

Jan 1, 1964

By R. H. Fernald

In investigating general problems that relate to the fuel resources of this country, and in testing fuels belonging to or for the use of the Government, the Bureau of Mines has given considerable attention to the efficiency and economic value of producer-gas power plants. Government inquiries during the past eight years not only have shown a very low fuel consumption per horsepower-hour for these plants but have demonstrated conclusively the possibility of utilizing commer- cially low grades of bituminous coal, lignite, and peat in plants prop- erly designed for the use of these fuels. The anthracite plant has been recognized as a commercial possibility for several years, although the cost of the fuel used has in general restricted these plants to com- paratively small units. The commercial development of the producer-gas power plant in the United States has been largely within the past six or eight years. In 1909 the United States Geological Survey published in a bulletin entitled "Recent Development of the Producer-Gas Power Plant in the United States" a list of producer-gas power-plant installations. The data presented in that bulletin showed a strong development in this field and led to much conjecture as to the future of this type of power. Owing to the extensive introduction of the steam turbine, however, many persons predicted the almost immediate doom of the producer-gas plant. In addition to the inroads made by this formida- ble rival, the interest of the gas-engine enthusiasts became centered to such an extent in the oil engine that the gas producer was relegated to second place by many and absolutely abandoned by some. During the past three years the belief of many who were formerly firm be- lievers in the gas producer has been that this type of power has reached its height of development in this country and that from a commercial standpoint it can no longer be regarded as a complete success. This feeling of commercial decadence has become so general

Jan 1, 1913

By R. V. Ramani, P. M. T. White, D. Sutton

1.1 General The examination and evaluation of a mineral deposit to determine whether or not it can be profitably exploited entails many factors unrelated to the physical nature and intrinsic worth of that deposit. Nevertheless, geology and geologically related factors have great bearing on the economic potential of the deposit. This is only natural because the deposit owes its existence to these factors. This is even more so in underground mines where the whole system is a geologically enclosed one. Geology plays a major role in at least four phases of a mineral venture. Firstly, it acts as an indicator of the existence of parti¬cular minerals. For example, it is inconceivable that a sedimentary coal deposit would exist in a granitic batholith or stock, or that a sandstone would host primary copper or nickel sulphides. Further, the positional relationship of different rock types may be significant in locating deposits such as replacement zinc and copper sulphides in limestones which have been intruded by igneous rocks. Thus, geology is important in the exploration phase of a mineral deposit. Secondly, once potentially valuable minerals have been discovered, knowledge of geology plays a significant role in determining the dis¬tribution, grade and extent of the mineralization. Controls on mineralization include one or all of those related to structure, rock type, sedimentary features, post-depositional redistribution, etc. Con¬sequently, in order to effectively evaluate a deposit in terms of

Jan 1, 1974

By C. A. Allen

"The problem of signaling to the hoisting engineer from a moving cage in the shaft has been considered by many mine operators for a number of years. There are several methods in use in different mining districts, and so far as the writer is aware they have been further developed in Utah than in any other state. The latest installations are of interest because they use a very low-voltage circuit for the shaft wires and also because the wiring can be so arranged that the hoist can be stopped from the cage, if so desired.The first installation in Utah was in the shaft of the Centennial-Eureka mine under the management of C. E. Allen. It was placed in operation in the summer of 1899, end has been in continuous and satisfactory operation for 21 years. The arrangement consists or two bare wires down the shaft carrying a current at 60 volts potential, with a device on the cage for making connection between the two wires. This device is simply a short piece of wire which is thoroughly insulated from the cage and is operated by a short lever. Whenever the cage rider wishes to signal the engineer he pulls down the lever, forcing the short wire out against the two bare wires, thus making a circuit which rings the bell in the hoist-room. A similar device was planned in the Grand Central shaft at Mammoth, Utah, but was later abandoned. The cause of failure was reported to be that the shaft was very wet."

Jun 1, 1920

By Edward Thimons, William A. Hertbrink

The effect of wind speed upon aerosol penetration into an idealized enclosure was studied The idealized enclosure was a painted plywood box that was 1 2X1 2 XI meters in volume Two fans supplied 1 7 m3 /min of filtered air to this enclosure at a static pressure of 2 8 mm of water The enclosure had a 7 5 cm diameter vent port which was isolated from the air flow around the enclosure To simulate holes in real enclosures, three 16-cm diameter holes were drilled on the front and back sides of the enclosure This simulated enclosure was placed in a tunnel-like structure The air flow from an ultra-light air craft was directed at the front of the enclosure The air speeds were varied between 14 and 36 km/hr as measured by rotating vane anemometer Static pressure in the enclosure was measured with an electronic manometer Two optical particle counters measured the particle number concentration of particles between the 0 35 to 0 5 µm inside and outside of the enclosure Aerosol penetration into the enclosure was computed as the ratio of the aerosol concentration inside the enclosure to the concentration outside of the enclosure The enclosure static pressures measured increase from 2 8 to 3 4 mm of water (P=00001) Aerosol penetration into the enclosure increased linearly with air velocity above 20 km/hr Theoretically estimated penetrations were correlated with observed penetration into the simulated enclosure When simple linear regression was used to model the observed penetration as a function of the estimated penetration, the value of the slope was 0 69±0 12 and the P value for the regression model was less than 0 0001 These results indicate that enclosure static pressure needs to be higher than the wind's velocity pressure in order to minimize aerosol penetration into these enclosures

Jan 1, 1999

By Jeffery L. Kohler, Eric R. Bauer

Prolonged exposure to noise over a period of years generally causes permanent damage to the auditory nerve and/or its sensory components. This irreversible damage, known as noise-induced hearing loss (NIHL), is the most common occupational disease in the United States today. Workers suffering from NIHL have difficulty understanding human speech and hearing other workplace cues. Despite the use of regulations and efforts by government and industry to reduce NIHL, the problem today is as prevalent as it was more - than two decades ago. Recently, the Mine Safety and Health Administration (MSHA) promulgated a new regulation that is designed to reduce NIHL in the mining industry. One of the more significant provisions is the elimination of MSHA's past practice of giving "credit" for the use of personal hearing protection, thereby reestablishing the primacy of engineering and administrative controls. However, there is a knowledge gap that is impeding the development and implementation of engineering and administrative controls. Although significant data exist on the exposure to noise by occupational code, little is known about the noise sources that contribute the most to the worker's dose. This is problematic in a workplace with multiple noise sources and workers who travel among noise sources. Yet without this knowledge, it is difficult to focus control efforts in any practical manner. Thus, it is important to characterize noise sources sufficiently well so that the sources most hazardous to hearing are identified and those conditions of exposure that are most amenable to engineering controls are pinpointed as well. The Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of noise sources and worker noise exposures in the mining industry to address this deficiency. The initial effort, conducted at a coal preparation plant and results are described in this paper. Preliminary analyses indicate that the noise levels on all floors exceeds 90 dBA in most areas, and that levels as high as 115 dBA were recorded. In addition, the one worker whose responsibility is to monitor the equipment and "house clean" the plant is slightly overexposed, even though he spends only half the shift in the plant. General information on the hearing loss problem in mining, a review of hearing protection use and noise regulations in mining, and other background materials are also presented.

By J. G. Schoning

The Holmes Safety Association is an offspring of the Joseph A. Holmes Safety Association which was organized in Washington, D. C., in 1916 at a meeting of representatives of twenty-four leading mining associations connected with every branch of the United States mineral industries. The purpose of the meeting was to do honor to the memory of Joseph A. Holmes, one of the founders of the United States Bureau of Mines and its first director, whose death had occurred the year before on July 12, 1915. In deference to what was believed would have been the expressed wish of this great humanitarian and benefactor of the mineral industries, it was decided to establish a national safety organization to cover the mineral indus¬tries exclusively; out of respect for his memory and service, the organization was named the Joseph A. Holmes Safety Association. On receiving requests from several mining districts, in 1922 a number of chapters ware established in several mining States.

Jan 1, 1929

By Jos. R. Guiteras

The present discussion first presents data to justify the fireproofing of mine shafts. This is followed by a brief outline of fireproofing methods with examples from practice. A summary of authoritative recommendations on fire prevention concludes the discussion. Acknowledgment is made to D. J. Parker, district engineer, Mine Safety Station, Salt Lake City, Utah, for his valuable criticism of the paper. Fireproofing a mine shaft implies lining the shaft with fireproof material or rendering fireproof the material already composing the shaft lining. A brief study of the part mine shafts and shaft stations have played in disastrous end tragic underground fires furnishes convincing evidence that every possible effort to make all mine shafts fireproof is amply justified. The fire hazard in coal minus obviously is much greater than in metal mines. In this discussion the point of views is mainly that of the metal miner; it is tine opinion of the writer that all fires in metal mines are preventable.

Jan 1, 1939

By J. R. Wait, D. A. Hill

A survey of the literature on ELF and VLF atmospheric noise has been made. Most measurements have concentrated on the vertical electric field and the horizontal magnetic field rather than the vertical magnetic field which is of interest in transmission between horizontal loops. The limited vertical magnetic field data indicates that the vertical component is generally 10 to 20 dB below the horizontal component. Three laterally inhomogeneous earth models have been analyzed for conversion of horizontal to vertical magnetic field. The rough surface model examines surface effects, the inhomogeneous thin sheet model treats volume effects, and the buried cylinder model treats localized man-made effects. All three models predict the possibility of significant conversion from horizontal to vertical magnetic field. A thin sheet model has also been used to examine transmission from a buried magnetic dipole source. It is found that the pre- dicted fields more nearly model the measured data than does the homogeneous half-space model.