Search Documents

By R. R. Sayers

The added hazards to mining incident to oil and gas wells penetrating the coal measures in proximity to mine workings , have long been recognized in those fields where the extraction of oil , gas , and coal , has been in progress for a number of years . The history of these fields is replete with stories of serious mine fires , explosions , and miraculous escapes from both fires and explosions due to either oil or gas finding its way into the mine workings through the strata , or by mining into an unknown or uncharted and abandoned oil or gas well that had not been properly plugged . The Director of the Bureau of Mines , in response to numerous requests from coal operators and oil and gas operators , called a meeting in 1913 to discuss necessary precationary measures to take when drilling oil or gas wells through workable coal beds and to try , if possible . to formulate a set of regulations that might serve as a guide to those persons preparing regulations covering the drilling of oil and gas wells in the various coal producing States . This meeting was attended by representatives of the coal , oil , and gas industries , State geologists , State mine inspectors , and representatives of the Bureau of Mines . A committee was appointed to prepare a set of regulations , which was later published as U.S.Bureau of Mines Technical Paper 53 ; the discussions and results of the meeting werepublished as U. S. Bureau of Mines Bulletin 65 . Later , the American Institute of Mining and Metallurgical Engineers appointed a committee to draft a model law for the use of the legislature of any State concerned . This committee made its report on April 27 , 1928 . Several of the coal mining States now have more or less comprehensive regulations governing the drilling of oil or gas wells through workable coal beds , others have regulations that are inadequate , while some have no regulations . The State of West Virginia recently enacted a law containing reg lations which are the result of a comprehensive and careful study of the problem .

Nov 1, 1929

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which type of plant utilizes more than the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which credo oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining.

Jan 1, 1935

By Jr. Driscoll

The thermoelectric properties of yttrium monoarsenide, yttrium monoanti-monide) and ternary materials from the Y-As-Se and Y-Sb-Te systems were investigated by the Bureau of Mines from room temperature to 1,000° C. The maximum calculated figure of merit for yttrium monoarsenide and yttrium monoantimonide was 2 x 10-5 ° C-1. YAs and YSb were semimetallic conductors with low Seebeck coefficients and electrical resistivities. The values of the Seebeck coefficient and electrical resistivity of the Y-As-Se and Y-Sb-Te materials were between those of the yttrium selenides and tellurides and of YAs and YSb, respectively. The maximum power factor calculated for the Y-As-Se materials was 2 X 10-5 watt/cm ° C2 which yielded an estimated figure of merit of 6 X 10-4 0 C-1. Most of the Y-As-Se compounds had high Seebeck coefficients and moderately low electrical resistivities. The Y-Sb-Te materials were degenerate semiconductors with power factors of 6 X 10-8 watt/cm ° C2.

Jan 1, 1967

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By Howard E. Parkinson

In 1969, new coal mine health and safety legislation was enacted in the United States. As a result of this legislation, the Department of Interior, Bureau of Mines has carried out communications research aimed at developing whole mine communications for increased safety and efficient operation. The research has advanced and many promising results are now being demonstrated to the mining industry. However, there remains a challenge to further improve wireless communications within the mine workings, and through the overburden above the workings. The objectives for future research and development will be discussed, together with the physical and operational constraints that new mine communication systems must face.

Jan 1, 1973

By W. K. Overbey

Surface fracture trace density, changes in roof rock type, and topographic unloading due to drainage were mapped for the mining areas located in the Blacksville-Osage, W. Va., quadrangles to investigate their influence on mine roof falls. Using these factors, a technique was developed to predict probable roof fall areas ahead of projected mining operations. As a feasibility test of this proposed technique, areas were delineated where one, two, and all three of these factors were operating to formulate a "potential hazard map" for comparison with roof fall observations that were made. The limited evidence suggests that in combination these factors are reliable predictors of where roof falls are likely to occur. This technique promises to be a useful tool in planning mining operations.

Jan 1, 1973

By A. R. T. Dennues

"INTRODUCTION There are presented in this report the results of limited studies by the Bureau of Mines of the firedamp safety of some powder-powered tools proposed for use underground in coal mines. This study was made to obtain general information and specific technical data for a cable splicer and some rail punches now commercially available, the aim being to keep abreast of developments and to anticipate hazards.ACKNOWLEDGMENTSAcknowledgments are made to the Mine Safety Appliances Co., Pittsburgh, Pa., for supplying equipment for these tests, and to the Pittsburgh Coal Co. for making possible observations of the use of these tools in coal mines.The assistance of other members of the Explosives Division is acknowledged: J. E. Crawshaw, for examination of ammunition and, propellant powders; H. L. Wilson, for analyses of the natural gas used in the gallery and Jerome C. P. Weinheimer and Martin Bashel, for conducting the gallery tests.GENERALDescriptions of the DevicesPowder-powered tools of the type tested utilize the energy of charge of,propellant powder accomplish tasks. They are essentially small guns adapted to special work. Of the family of such tools now commercially available from one manufacturer, two have been proposed for use underground in coal mines, namely a cable splicer known as model TI and two models of rail punch known as R40 and R60. These tools employ blank-cartridge ammunition and special projectiles to accomplish the work indicated by these descriptive names."

Jul 1, 1947

By Adam K. Smith

Over-exposure to noise remains a widespread, serious health hazard in the U.S. mining industry despite 25 years of regulation. Most other categories of illnesses and injuries associated with mining have improved, with the exception of hearing loss. In order to reduce cases of Noise Induced Hearing Loss (NIHL) in the mining industry, retrofit acoustic treatments and controls are being developed to subdue noise at the source. The Mine Safety and Health Administration (MSHA) coal noise sample data collected from 2000 to 2005 has determined that continuous mining machines rank first among all mining equipment whose operators exceed 100% noise dosage. The continuous mining machine conveyor, used to move coal from the cutting face to the rear of the machine, has been identified as a dominant noise source. A dual sprocket conveyor chain was tested as a potential solution. Sound power level measurements conducted at the Pittsburgh Research Laboratory (PRL) accredited reverberation chamber showed a 3 dB reduction in the A-weighted sound power level when the dual sprocket chain was implemented. Underground results show an 8-hour Time Weighted Average (TWA8 hrs) reduction a 3 dB for continuous mining machine operators. Utilizing this newly developed noise control, along with previously proven controls, provides continuous mining machine operators an opportunity to be within the MSHA-Permissible Exposure Limit (MSHA-PEL).

Jan 1, 2009

By J. D. Zetterstrom

This report supplements an earlier publication on lightweight aggregates of North and South Dakota.3/ The purpose of the investigation was (1) to study the expansion characteristics of large samples of Dakota clays and shales in a 12-inch by 15-foot rotary kiln; and (2) to improve the laboratory bloating test as a tool for predicting the suitability of samples for the rotary-kiln process. This was done by comparing results of the laboratory and kiln tests.

Jan 1, 1956

By Geo. Adams Roalfe

THIS PAPER is one of a series being pre¬pared for and published by the United States Bureau of Mines describing, methods of mining and crushing and the costs of operation at commercial crushed-stone plants throughout the country. These papers are designed to disseminate technical information regarding the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators, as well as to the industry as a whole. On the other hand, operating, costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. Acknowledgments The author wishes to acknowledge the [ ]

Jan 1, 1932

By C. L. Klingman

In extracting helium from natural gas at Bureau of Mines helium plants, a continuous analysis of the helium content of inlet and outlet gas streams is required to determine extraction efficiency. An analyzer, using established principles of gas chromatography to effect the analysis, has been developed by the Bureau of Mines to meet this need. It will record the helium content of inlet or discharge gases from helium-extraction plants every five minutes, continuously, without the attendance of an operator. A 25-inch column of activated charcoal is used as a partitioning agent; nitrogen is the carrier gas; and a hot-wire, thermal-conductivity cell is the detector. A 1.0 mv, strip chart indicates the unbalance of the detector cell, Sample size is 0.37 cc, and carrier gas flow rate is 75 cc, per minute. Significant improvements in helium extraction have been demonstrated by using the chromatograph in three helium-extraction plants.

Jan 1, 1961

By D. G. Kesterke

The electrolytic reduction of uranium dioxide to molten uranium in fluoride baths at approximately 1,200° C was demonstrated. Electrolyte constituents were BaF2, UF4, and either MgF2 or LiF. Preliminary laboratory-scale experiments were made in which the uranium oxide was added continuously for 3 to 5 hours to the cell during electrolysis. Over 1,000 grams of metal of 99-8 percent purity was made in some tests, Major impurities were aluminum, barium, iron, silicon, carbon, and oxygen. The effects of cell design, geometry, and bath composition were investigated. Electrode arrangement was the most important factor in cell performance.

Jan 1, 1963

By R. R. Schehl

The Bureau of Mines has developed a quantitative Analysis for pyrite in coal by X-ray diffraction that can be accomplished in little more than 1 hour. To minimize the sample analysis time, data processing has been completely computerized with pertinent output information displayed on a VR12 cathode-ray tube display. Use of this computerized system is not only advantageous during the experimental stages of the pyrite analysis project but would also be essential if the X-ray diffraction procedure is accepted as a standard method of analysis.

Jan 1, 1973

By Bruce D. Sartwell

A program was written which utilizes a remote teletype input to a time- sharing computer to plot charged particle or X-ray energy spectra which are stored in the memory of multichannel analyzers. The program, written in FORTRAN V, accepts the data printed out by the pulse height analyzer on paper tape and then, after reading these data tapes into the computer, plots on the teletype the desired energy spectra on a scale automatically adjusted for the maximum number occurring in the data. The program is flexible enough so that the researcher can subsequently expand or contract the vertical (intensity) or horizontal (energy) scales. With a slight modification, the program will accept data printouts from scalers or analog to digital converters. The program also includes a feature for integrating the energy peaks obtained by pulse height analysis.

Jan 1, 1970

By G. R. Hopkins

The average quantity of heat needed to refine a barrel of crude oil in 1934 was 638,000 B.t.u., or about as much heat energy as contained in 5 gallons of fuel.oil. Although the total heat utilized in 1934 was slightly above 1933, crude runs to stills increased 4 percent, hence the average requirement per barrel declined from 660,000 B.t.u. in 1933 to 638,000 B.t.u. in 1934 (see fig. 1). The average for 1934 constitutes a new record for firing efficiency, being just under the previous low of 1929. Heat consumption at refineries depends on many factors, of which the trends in yields of gasoline and lubricating oils are probably most important. The yield of gasoline is indicative of activity at cracking plants, which typo of plant utilizes more thou the average amount of heat per gallon of product. The yield of lubricating oils is indicative of the extent to which crude oil is refined; that is, it takes considerably more heat to refine a barrel of crude through lubricating oils than it does to separate only gasoline and kerosene. The yield of gasoline decreased from 43.7 percent in 1933 to 43.4 percent in 1934; on the other hand, the yield of gas oil and fuel oil increased. Although the yield of lubricating oils increased slightly in 1934 the theoretical increase in fuel requirements probably was offset by technical improvements, such as solvent refining. Although no outstanding technical developments of a fuel-saving nature were made in 1934, some progress undoubtedly was recorded. Heat exchangers, an effective fuel-saving device, wore enlarged, and some refiners now take off several cuts before the crude reaches the pipe stills. The total capacity of pipe stills increased 2.5 percent in 1934, and many of the less efficient shell stills were torn out.

Jan 1, 1935

By J. B. Littlefield

The Greenburg-Smith impinger was developed at the Bureau of Mines in cooperation with the United States Public Health Service in 1922 in the course of an investigation of dust-sampling instruments available at that time. Although it is not used extensively outside of the United States, it is now soused in this country to collect samples for the determination of any dustiness, and most of the information correlating degree of dustiness with physiological effect has been obtained by the impinger method. The chief disadvantages in the use of the regular impinger, especially in mines and other places accessible with difficulty, are its bulk, weight, and power requirements. It requires a source either of electricity or of compressed air, which necessitates connections and extension of existing supply lines to each sampling point; the only alternative is the use of a relatively large pump hand-operated with considerable effort.

Jan 1, 1937

By R. R. Sayars

"Carbon monoxide is a gas slightly lighter than air, with which it diffuses readily to make a homogeneous mixture. It will burn and has a wide explosive range, that is, an explosion is possible when the air contains from 15 to 73 per cent of the gas3. This explosive range is about the same as that for hydrogen and over nine times As Tide as that for marsh gas (methane). Like air, it has neither color nor taste and has no odor in concentrations usually encountered, therefore it cannot be detected by the ordinary senses with which men are endowed. It is produced by burning carbon containing fuels, no coal, wood, gasoline, etc., whenever not enough air or oxygen is supplied to burn and oxidize the fuel completely.The human race has probably been exposed to this gas since men first began using fires in confined or sheltered places. The poisoning as usually encountered is an acute condition resulting from breathing atmospheres con¬taining this gas. A number of eases described in the ancient literature Indicate that carbon monoxide was a frequent cause of death by accident, suicide and is a means of punishment or torture. A quotation by Lewin from Aristotle who lived in 384-322 B.C., states that ""animals collapse from harmful odors as men gets a severe headache and often dies through charcoal vapors"". The Roman knew that smoke was poisonous, and used the greenest most smoke-producing wood to put persons to death. The occurrence of carbon monoxide increased in frequency through the years until at the present time it is found in the home as well as in many industries. The following table gives the approximate percentage of carbon monoxide found in gases from various sources of poisoning.4"

Apr 1, 1924

By John C. Ferm

This report contains a summary of Phase I and complete results of Phase II portions of a study of geologic factors associated with roof falls in mines on the Pocahontas #3 coal seam in southern West Virginia and southwestern Virginia. Principal objectives of Phase I was the selection of five mines that best portrayed the spectrum of roof and mining conditions and Phase II consisted of a measurement and documentation program for each of the five mines. The documentation measurement program included reconnaissance mapping, detailed mapping, joint measurements and coring roof rock. 1.2 PHASE I RESULTS The results of Phase I consisted of the selection of the following five mines for detailed study: Virginia Pocahontas #3 (Island Creek Coal Company), Bishop (Consolidation Coal Company), Shannon Branch (Allied Chemical Company), Keystone II (Eastern Associated Coal Company) and Macalpine-East Gulf (Westmorelenad Coal Company). In addition, Phase I results, which were based on questionnaire data, indicated that the kind of rock in the roof --gray sandstone, crystallized sandstone, laminated sandstone and shale, grey shale, slickensided shale, and rider seams could be associated with good and bad top areas. Also presence of vertical separations, bolt length, entry and cross-cut width, length and torque on bolts and depth of overburden seemed to be related factors. These data provided a focus for the Phase II measurement program.

Jan 1, 1975

By Charles E. Munroe

On March 14, 1921, an explosion occurred at about 6:15 A.~. on the premises of an iron-mining concern throug:1 which two magazines, one containing upwards of 9,000 pounds ot a high explosive of the dynamite class, and a second, 60 feet distant, containing upwards of 10,000 No. 6 detonators, were completely destroyed, and a ncratertt,? f3et deep by 30 feet in diameter, was excavated in the gro~ at ~he place whare the mag~iine containing the high explosive had been lo~ated. As a rule any eye wit~esses to the circumstances im.~ediataly preceding and d(irectly concurrent with a.c.ci.:lental ex;losions ar.e victims of s11ch explosions, and, therefore, the conclusions reached as to the cauoa. of such explosions must, perf'orce, be based aln:ost completely on circumstantial evidetJ.ce. In this iii.stance, b:ecause both the explosive and detonators were of -orov{:;d: character; because of the time of the day and the state of operations iit the·· time of the e:.q,losion; because the rerroteness of the location of the n:-1agazi::1es 1 0::1 the side of a ravine, easily admittfi of unobserved approach; beca:iise differencas existed, and because no obvious cause was at once apparent, there arose suspicfon that the explosion was not accidental.

Sep 1, 1921

By Brian White, Hamid Maleki

Sudden, violent failures of rock around mine openings influence access, ventilation, and safety in both hard-rock and coal mines. To develop predictive tools for assessing the potential for violent failure, the authors initiated a comprehensive study using (1) multiple linear regression and numerical modeling analyses of geological and mining conditions at 25 sites to identify the most significant factors contributing to stress bumps in coal mines and (2) investigations of the geological and mining factors contributing to rock bursts in the Coeur d'Alene Mining District of northern Idaho, particularly the influence of preexisting structures on rock bursts. Twenty-five factors were initially considered in the study of coal bumps. The most important variables were identified as (1) mechanical properties of strata, (2) gate road geometry and/or gate pillar factors of safety, (3) roof beam thickness, joint spacing, and stiffness characteristics, and (4) stress gradients associated with previous mining and anomalous geologic conditions. In the Coeur d'Alene district, burst damage related to preexisting structures results primarily from (1) sudden buckling and crushing of rock layers where surfaces of development and production openings lie at low angles to bedding, faults, or other planar structures and (2) disturbance of loose ground caused by seismic fault-slip on preexisting faults or previously sheared bedding planes that intersect veins near pillar-stope margins.