Search Documents

By H. William Zeller

The Bureau of Mines performed laboratory research into the effects of a barium-based fuel additive (the "postflame" type) on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of types certifiable for use in underground mines. Test parameters consisted of additive concentration and engine loads, speed, and air intake restriction. DPM emissions, including condensed volatiles, were measured gravimetrically. Also measured were gaseous emissions including carbon monoxide, nitrogen oxides, and hydrocarbons. The fuel additive was effective, reducing DPM up to 75 pct, when used at a concentration of 0.09 wt pct (one-fourth of the concentration recommended by the manufacturer). The additive was most effective at the highest fuel-air ratios, reducing DPM from 400 mg/m3 for untreated fuel to 120 mg/m3. At light loads, 25 pct of full rated, no DPM reductions were measured. Based on these results, the additive is recommended for use in diesel fuel, at a concentration of 0.09 wt pct, to power underground mining equipment as long as certain conditions are met: that a beneficial DPM reduction is verified, that the minimum required quantity of additive is used, and that potential adverse effects such as increased nitrogen oxides are checked.

Jan 1, 1990

By Lloyd A. Morley

This report details the continuation of mine power systems transient research under USBM Grant G0155003. The purpose of the work, which commenced under Grant G0133077, is the elimination of safety hazards created by transients" and the objective is to provide knowledge about transients existing in a-c and d-c coal mine power systems. The report chapters cover theoretical background, instrumentation, and experimental investigations. The instrumentation discussion scans measurement problems and considerations plus the development of a low-cast peak-detector. Transient data from in-mine measurements are presented and include high-voltage distribution and d-c trolley systems. Extremely unique field exercises are described involving actual power equipment connected on the surface to duplicate typical underground coal mine system arrangements. Here, transients on high-voltage distribution resulting from vacuum circuit breaker operations could be observed under controlled conditions, and work centered around how surge capacitors effect transients. Using the in-mine and staged transient data, specific conclusions and recommendations are made with emphasis on high-voltage distribution.

Jan 1, 1977

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By J. J. Jakosky, D. H. Zellers

"IntroductionThe Bureau of Mines has been conducting experiments in underground communication during a period of several years, and a brief summary of what has been done is as follows:During 1919-1920, investigations were conducted with the geophone. This instrument was used extensively during the World War for detecting enemy digging and mining operations, by means of the vibrations transmitted through the earth strata.A preliminary investigation using short wave-length (200 to 300 meters) radio equipment carried out jointly with engineers of the Westinghouse Electric & Mfg, Co. during 1922.The step was to investigate ground conduction signaling, (called T.P.S. in Signal Corps parlance)."

Nov 1, 1924

By Ann G. Kim

Samples of gas were obtained directly from the coalbed during drilling of horizontal and vertical boreholes in six different formations. The samples were analyzed by gas chromatography for C1 to C5 hydrocarbons and for 02, H2, H2, He, and C02. Methane in the gas varied from 63 to 99 percent; carbon dioxide from 0.1 to 15 percent. The CH4 /CO2 ratio varied and showed no apparent correlation with age, rank, or bed. The majority of samples contained ethane, propane, and butane; hydrogen and helium were found in some samples. Oxygen and nitrogen were usually present, possibly as a result of air contamination. A more extensive sampling program would be necessary to establish relationship between the amount and composition of the gas in the coalbed and other factors.

Jan 1, 1973

By Frank J. Susko

The U.S. Bureau of Mines is developing a process for removing metals from mining and mineral processing waste streams by precipitation. The precipitation process is accelerated by flocculation when a high molecular weight polymer is added. Infrared (IR) studies were performed on zinc hydroxide [Zn(OH);J, copper hydroxide [Cu(OH);J, and zinc sulfide (ZnS) flocculated with both non ionic and anionic polyacrylamide (PAM) and polyethylene oxide (PEO). The IR data were compared with general trends in the performance of the polymers observed during flocculation. These studies will help to understand the bonding between the precipitate and polymer and indicate the effectiveness of a flocculant for dewatering. Two types of bands showed up on the IR spectra; one type described the interlayer water of the flocs, the other described the organic bonds of the polymers. A general decrease in the areas of the three water bands, hydroxyl (O-H) stretching (3,200-3,500 cm-1), water bending (1,610-1,630 cm-1), and torsional oscillations (600-700 cm-1), indicate interlayer water being driven off, which is a favorable condition in flocculation. Shifts in the O-H stretching band indicate water bridging between the precipitate and polymer. Shifts in the amine (N-H) deformation, carbon-nitrogen (C-N) stretch band (1,600-1,610 cm-1) indicate the amine group of the PAM is involved in the bonding. Evidence suggests that ether oxygen of PEO is also involved in the bonding process.

Jan 1, 1990

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers' equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer's manual and making the appropriate cable valve adjustments.

Jan 1, 1976

By Timothy J. Rohrbacher

This report presents a U.S. Bureau of Mines study that incorporates coal mining factors, coal recovery factors, and economic factors into the definition of an economically recoverable coal resource. The relationship between these factors to the Energy Information Administration's estimate of U.S. coal resources-the "Demonstrated Reserve Base"-is discussed. The Matewan 7-1/2 minute quadrangle in eastern Kentucky was selected as the initial study area. Results indicate that of the original 1,193 million tons of resource in the quadrangle, only 89 million tons (7.5%) are economically recoverable at a cost of $25 per ton or less. At the current production rate of 5.3 million tons per year, this represents only 16.8 years of remaining reserves.

Jan 1, 1993

By H. H. Hill

"The wide publicity that is given to the discover; of new oil fields has led many people to believe that our supply of crude petroleum is practically in- exhaustible and that in order to keep pace with the demand for petroleum products, it is only necessary to drill a few more wells in some of the south-western states. It is not generally realized that, although many famous fields have been developed in Oklahoma, Kansas, Texas and Louisiana during the past few years, the production of crude oil in 1919 was not sufficient to meet the demand and it was necessary to import approximately 53,000,000 barrels from Mexico.Continued efforts are being made to recover a larger percentage of the oil underground by improvements in methods of drilling and in handling producing properties. Improvements are also being made in methods for handling the oil after it has reached the surface which will result in reducing losses through leakage and through evaporation. These methods for cutting down waste in production and storage, if universally adopted, will no doubt result in appreciable increases in our supply of crude oil."

Nov 1, 1920

By Henry M. Harris

The Bureau of Mines investigated a glass containing approximately 17 percent lithia and 83 percent silica to establish a method of devitrifying cast and rolled shapes. Glass shapes with high strength were made by melting, forming, and rapid cooling of the composition, and the shapes subsequently were converted to a crystalline condition by heat treatment. The best devitrification schedule included rapid cooling of the glass to below 300° C, followed by reheating at a rate of 50° to 400° C per hour, depending on the size of the shape, followed by a of 60 to 70 hours at 500° C and another period of 15 hours at 800° C. attempts to use faster heating rates or slow cooling to accomplish devitrification in deformation of the shapes. The crystalline shapes had flexural strengths that averaged over 33,000 psi, achieved with an annealing time of 60 to 70 hours at 500° C.

Jan 1, 1965

By David W. Wisecarver

This report describes a tool to engage and/or place a Bureau of Mines type gage to measure borehole deformation in a horizontal , 1½ - inch - diameter , stress relief borehole . The tool was successfully used at a borehole depth of 105 feet . Practical usage up to borehole depths of 200 feet might be realized . The tool was designed to work inside EX- size ( 1½ - inch ID ) diamond - drill drive casing used as drill rod and through which the deformation gage is guided into an EX- size stress relief borehole . Through laboratory experiments it was found that by exercising a reasonable amount of care the deformation gage could be placed at a point within a ± .01 foot distance of a predetermined depth in a horizontal EX- size hole and that the deformation measuring piston or plunger of the gage could be oriented in the borehole within 0.5 ° of a preselected angle of orientation in a vertical plane .

Jan 1, 1964

The faculty, graduate students, and post-doctoral researchers are an integral part of the Generic Mineral Technology Center for Respirable Dust. More than fifty (50) scientists, engineers, and medical personnel are engaged in respirable dust research at five universities, The Pennsylvania State University, West Virginia University, Massachusetts Institute of Technology, University of Minnesota, and Michigan Technological University. The expertise, effort and contribution of these individuals has proven to be invaluable in the attack on respirable disease. Nationally and internationally recognized researchers in the areas of particle characterization, interaction of dust and lungs, dilution and dispersion, rock mechanics and continuing education lend their laboratory facilities, equipment and human resources to benefit the mining industry. The expertise and resources of the National Institute for Occupational Safety and Health--Division of Respirable Disease Studies is available through their relationship with West Virginia University.

Aug 31, 1989

Provide the technology to remotely reset circuit breakers on continuous mining machines used in extended cuts.

Jan 1, 1994

By W. M. Myers

"The continued expansion of modern industry broadens the markets for minerals and their product. With these increasing demands new uses are being found for minerals that heretofore were considered as possessing no commercial possibilities. This tendency is reflected in the nonmetallic field in a constantly increasing demand for minerals formerly considered to be of scientific interest only, Furthermore, nonmetallic minerals of established commercial importance are used in new ways in various products, and this tends to expand the markets for these minerals. Some recent outstanding developments in applications of minerals are given in the following pages.The Andalusite GroupAmong the minerals that until recently were considered of scientific interest only, may be listed those of the andalusite group. This group is composed of the three minerals, andalusite, cyanite (or kyunite), and sillmanite, which are all forms of the compound Al2SiO5 (A1203, S1O2), and are therefore identical in chemical composition, but differ in physical properties,"

Mar 1, 1924

By H. V. Makar

An aluminizing dross which is accumulating as a waste material in substantial quantities was tested for possible use as a steel deoxidizer. This material, consisting mainly of aluminum, silicon, and iron, was used to deoxidize laboratory-scale melts ranging from 7 to 100 pounds. Oxygen analysis showed that the aluminizing dross was effective in reducing oxygen levels in steel. A direct comparison with aluminum wire showed the dross material to be at least as effective. Under similar test conditions with 7-pound melts, 3 grams of aluminum reduced the oxygen concentration from 210 to 175 ppm, while 4 grams of aluminizing dross (equivalent to approximately 2 grams aluminum) reduced the oxygen concentration from 250 to 170 ppm. An additional 4 grams of aluminizing dross produced a final oxygen concentration of 140 ppm.

Jan 1, 1972

By Richard J. Kline

The underground mining industry is presently using the fluid network analyzer and digital computer to analyze ventilation systems. The availability of the digital computer and ventilation programs to mining companies has escalated its use, permitting the design and modification of new or existing mine ventilation systems to be projected completely and thoroughly with consistent precision. Because the analog computer has been analyzing ventilation systems accurately for many years, a comparison of the analog and digital methods was warranted. This report summarizes a detailed comparison for one mine, based on parallel analyses by the two computer systems.

Jan 1, 1972

By E. M. SEELEY, F. S. LOTT

Expansion in total capacity of the natural-gasoline industry.to produce light products continued in 1944 and 1945. The average rate of gain, however, was reduced to about 6 percent annually from over 9 percent in the preceding 4-year period. New facilities at cycle plants again accounted for most of the increase in productive capacity. Between January 1, 1944, and January 1, 1946, the number of cycle plants increased from 32 to 37 and their total capacity from 3,278 thousand gallons daily to 4,848 thousand (48 percent). Capacity of all other plants in the industry increased in the same period from 12,735 thousand gallons daily to 13,080 thousand, or only 3 percent. The capacity of the average plant increased to 28,600 gallons a day from 24,400 gallons on January 1, 1944, continuing the established trend. The average capacity of cycle plants increased to 131,000 gallons a day from 102,400 gallons, and the average capacity of all other natural-gasoline plants increased to 22,200 gallons a day from 20,400 gallons. Although the number of plants increased in only three States in the 2-year period (Texas, Okla- homa, and Arkansas), the total capacity of plants increased in eight States. A further decline of 29 reduced the total number of plants to 626 on January 1, 1946. Compared with 10 years earlier, gasoline plants were more numerous in only 4 States: Texas (48 more), New Mexico (7 more), Arkansas (2 more), and Louisiana (1 more). The largest declines, in order, were in Oklahoma, Illinois, Pennsylvania, West Virginia, and California. The number of plants with fractionating equipment for separating the liquefied gases from heavier fractions was 202 on January 1, 1946 and 182 2 years earlier. The principal changes in number and capacity of shut-down plants were an increase in Texas and a decrease in California. Shut-down natural-gaso- line plants are usually among the smallest units in their vicinity.

Apr 1, 1947

"When a metal-mining company takes out a workmen's compensation insurance policy, it does so to relieve itself of its uncertain and variable financial liability under laps requiring payment to employees for lost-time accidents, there-by passing the liability or to the insuring agency. For this service, or rather for the assumption of the risk, the insuring agency charges the mining company a price, or in insurance parlance, ""a premium"".The insuring agency depends upon a volume and variety of business to average the losses incurred by its individual policy holders, and determines its price to cover losses that are suffered and its cost of doing business.It is generally known that all types of insurance are founded on the theory of probability applied to large groups of risks, Workmen's compensation insurance is no exception, and the average price paid therefor must be based on the frequency and severity of accidents in the particular industry or branch of industry under consideration. The frequency and severity rates are determined by statistics, which, of course, unless standardized, kept carefully and consistently, and analyzed properly, are liable to be inaccurate and misleadingThe importance of large groups in arriving at an average price for insurance service can not be overestimated, For example the writer knows of one small group of some twenty metal-mining companies whose losses during the past two years exceeded their premium charge by 54%. Not a single individual company during the two years kept its losses below the premium rate. For several years the group as a whole has persistently exceeded its premium rate, Such risks are not profitable to the insuring agencies and can only be carried where a large volume of good risks will balance the poor risks, but in order to conform to good insurance ethics the premium rate must be based on averages for the industry as a whole, and kept sufficiently low to induce operators to sell their risks."

May 1, 1924

By T. A. Henrie, D. C. Fleck, D. G. Kesterke

Uranium metal was electrowon from uranium dioxide dissolved in fluoride melts . The UO₂ was fed directly to the cell in a continuous manner . Electrolysis was performed at 1 , 200 ° to 1,300 ° C in electrolytes composed of UF4 , LiF , and BaFa . A single regulus of metal was collected in a confined area of the crucible . Product purity of 99.8 percent was attained . Carbon was the major contaminant . Compartmented cells were studied as a means of confining the oxide feed to the vicinity of the anodes .

Jan 1, 1964

By R. V. Higgins, H. C. Miller

"INTRODUCTION The development of methods for determining the total quantity of crude oil that a given pool could be expected to produce in the future and the well-spacing and drilling programs most likely to result in the recovery of the maximum quantity of oil at the minimum cost became problems of acute concern to American oil producers and petroleum engineers during the second decade of the twentieth century, The United States faced what seemed at that time to be a serious shortage of petroleum, and it appeared that the constantly increasing demand for petroleum and its products could not be adequately supplied. Undrilled prospective acreage, which until then had been plentiful, seemed to be getting scarcer, competition was increasing, the margin of profit to the producer was shrinking, and the need for developing constructive policies of conservation appeared paramount. As a result of physical and economic changes then taking place within the petroleum industry prompted by the seemingly uncertain future, accurate knowledge pertaining to the probable future production of oil wells and of oil lands especially was needed and greatly desired. Furthermore, the need for obtaining the maximum quantity of oil from known fields caused technical information - which up to that time had not been deemed essential to the successful and profitable operation of oil lands - to be sought eagerly. The need for technical information, such as methods for determining future reserves of oil and the rate at which the oil could be obtained under a specific program of drilling, was emphasized further with the passage of the Revenue Act of 1918, and oil producers with enough income to place them in the taxable class were compelled, for the first time, to report their taxable income 4/ to the Treasury Department."

Nov 1, 1939