Search Documents

By Erle C. Donaldson

The pendant drop interfacial tensiometer is being used to study interfacial phenomena that influence the production of crude oil. A description of the instrument showing the modification of the cell and cell holder is presented. The modified cell and cell holder allow formation of a precise and reproducible drop size, and the image of the drop is easily alined and focused. Interfacial tension measurements and observations of film formation can be conducted at various temperatures with the jacketed cell.

Jan 1, 1967

By Robert P. Vinson

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

By J. B. Newson

This is one of a series of circulars dealing with mining methods, practices, and costs. It describes the method of sinking a shaft 60 inches in diameter with a shot drill, as employed at the Idaho Maryland mine, Grass Valley, Calif. The operation involved a great deal of experimentation in applying the shot-drill method to large bore drilling, overcoming mechanical and other difficulties which developed during sinking, and developing operating technique. Under such circumstances, costs are obviously higher than they would be after the pioneer work has been done, but even so, these actually obtained compare favorably with costs of sinking by more conventional methods. ACKNOWLEDGMENTS The authors are indebted to Mr. Errol McBoyle, president of the Idaho Maryland Mining Co., not only for his cooperation and advice during the sinking of this experimental shaft, but for permission to prepare this article for publication with the inclusion of cost data.

Jan 1, 1936

By T. C. Phalen

"Necessary Qualities There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, also, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the ele¬ments, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of ad-hearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco."

Dec 1, 1919

By E. F. Ferrell

Gold was recovered from scrap electronic 60-40 (tin-lead) solders by drossing with aluminum or zinc at elevated temperatures. The gold, together with other metallic impurities, collected in the dross phase which could then be separated from the molten solder by skimming or filtering. Drossing upgraded the gold concentration by a factor of 10. Further upgrading was achieved by a combination of steps including an oxidation roast and either a combined cyanidation-amalgamation treatment or an aqua regia leach. The gold was then recovered in highly concentrated form from the aqua regia or cyanide solutions by cementation and from the amalgam by volatilization or dissolution of the mercury. The solder was purified by reaction with NaOH to remove dissolved aluminum or with SnCl2 to remove dissolved zinc.

Jan 1, 1976

By Frank E. Chase

Kettlebottoms are columnar masses of rock--the preserved casts of ancient tree stumps--embedded in coal mine roof strata (of which they are a part). Because unsupported kettlebottoms can detach from a mine roof without warning, they are a hazard to miners. The primary objectives of this investigation were (1) to better define and describe kettlebottoms and (2) to evaluate kettlebottom support techniques in terms of safety and effectiveness. A telephone survey of mine operators, interviews with Mine Safety and Health Administration (MSHA) personnel, and underground mine visits were conducted in Pennsylvania, West Virginia, and Kentucky. Information gathered during this investigation indicates that the size and frequency of kettlebottoms in mine roof are dependent upon past geologic events and biological processes active during the deposition of roof sediments. To ensure the safety of mine personnel, all undermined kettlebottoms should be supported. The roof should be bolted next to kettlebottoms less than 3 ft in diameter, close enough to allow a portion of a wood or steel header to be extended beneath each kettlebottom for support. Two bolts and a wood plank or steel strap should be employed to support kettlebottoms over 3 ft in diameter.

Jan 1, 1983

By H. Kim, R. W. Plummer, T. J. Stobbe

"The probability of developing coal workers' pneumoconiosis (CWP) varies among miners in different geographic areas, coal seams, and jobs. Many studies have revealed the correlation between mineral content and the frequency and severity of CWP development still remains controversial. Furthermore, the mineral content and its variability in different areas is unknown.Since mineral content is expected to vary from location to location within a mine, between mines, between coal seams, and over time, this information will be valuable in understanding the variations in CWP incidence, as well as in establishing the appropriate kinds of dust to use in toxicological research programs studying CWP.Size-selective airborne dust samples were collected using 4-stage cassette impactors at 9 different locations in each of five coal seams. These coal seams were the Upper Freeport, Pittsburgh, Kittaning, Coal Burg, and Pocahontas. Mineralogical analyses were done by a x-ray powder diffraction photographic technique.Common minerals found in coal mine dust were illite, calcite, kaolinite, quartz, siderite, dolomite, gypsum, anhydrite, and pyrite. The distribution of minerals in interand intra location samples will be reported. Early results on the mineral content show wide variations between locations.in a mine and between coal seams, and small, but significant, variations between particle sizes.INTRODUCTIONIn spite of its long history of incidence, and the large amount of research conducted on it, coal workers' pneumoconiosis (CWP) is still prevalent among coal miners and needs further research to develop effective preventive and remedial measures. Although the dose-response relationship between simple CWP and coal mine dust has been established (1), the causal agent(s) and the mechanism(s) involved in the progression of simple to complicated CWP are not yet defined. Many plausible hypotheses have been made to explain the mechanisms involved in the disease progression however none of them is satisfactory. In addition, the source of variation in occurrence of CWP among miners in different geographic areas (2), rank of coal seam (3,4), and job (5) remain unsolved."

Jan 1, 1988

By Raja V. Rarnani, Robert L. Frantz

"The Generic Mineral Technology Center for Respirable Dust (GTCRD) was created at The Pennsylvania State University and West Virginia University by a congressional initiative in 1983 responding to recommendations in the 1980 National Academy of Sciences study on the Measurement and Control of Dust in Mines. Many of these recommendations dealt with the need to initiate focused fundamental research for further professional progress in dust control. Long-term, sustained support was emphasized to develop expertise in respirable dust research. In creating this Center, Penn State and West Virginia University were specifically recognized for their expertise in and facilities for research on coal mining and medicine. Today, the Center includes the Massachusetts Institute of Technology, the University of Minnesota, and the Michigan Technology University. The Respirable Dust Center is the only organization that coordinates and integrates the medical, scientific, and engineering aspects of respirable dust disease. The Center works with the U.S. Bureau of Mines (USBM), Mine Safety and Health Administration (MSHA), the National Institute for Occupational Safety and Health (NIOSH), the United Mine Workers of America (UMWA), and the U.S. coal industry in defining the research priorities for the programs of the Center to enhance research synergism.The Center's mission is to enhance the health, safety and productivity of miners by advancing the fundamental understanding of all aspects of respirable dust associated with mining and milling and the interaction of dust and lungs to reduce the incidence and severity of respirable dust disease.All Dust Center activities are focused to be responsive to this mission, which is shared by the several federal agencies closely associated with the GTCRD. While significant progress has made mine atmospheres cleaner and healthier, respirable dust-related disease remains the nation's most pernicious industrial hazard.The goals of the GTCRD were formulated with recognition of the diverse scientific, engineering, and medical aspects of respirable dust, in addition to a need to enhance researcher interaction, as well as education and technology transfer efforts, in the respirable dust area. These goals reflect the needs of the mining industry as determined by the National Academy of Sciences Committee on Measurement and Control of Respirable Dust study done in 1980. The report of this committee encouraged the Bureau of Mines to redirect its research efforts ""...toward obtaining fundamental understanding of the origin, transport and characteristics of respirable coal mine dust."" The GTCRD's goals, detailed in chapter three of this document, were formulated to mesh with NAS recommendations."

Jan 1, 1995

"There mines are located in out of the way places, where timber is scarce and its price high, the problem of protecting it from fire risk is of considerable practical importance. Scarcity of timber for mining purposes is commonly met with in the more arid parts of the country, where, so, mine timbers are most likely to become dry, and inflammable, and where, therefore, the risk from fire is accentuated. Any effective and cheap method of securing adequate protection of such timber at the lowest possible cost is worthy of careful investigation. The use of magnesite cement has been suggested in this connection.The necessary qualities for any substance for the use suggested above may be summarized as follows: It should be resistant to abrasion, and to impact and structural stresses. It should be durable when subjected to the action of the elements, and stable to any minor derangements of the base on which it is placed. It must be relatively unaffected by changes in temperature, by the action of water, and should adhere to the material on which it is placed, and it should also be free from shrinkage cracks due to setting up the material, Magnesite cement appears to fulfill the various conditions outlined above.The elasticity of such cement is the outstanding quality which makes it desirable for exterior work. It also possesses the ability to adhere to all materials in a marked degree. Its freedom from expansion and contraction after setting is one of the principal reasons for its adhesive quality. It may be applied to old brick or stone walls, even tho they have been repeatedly covered with paint, and the quality of adhearing to wood makes it possible to secure a weather-proof protection to the wooden casings and trim of exterior openings. The quality of adhesion and elasticity is easily proved by applying a 1/2"" layer to a 1"" board which has been first covered with metal lath. Such a board, about 8 feet long, may be repeatedly deflected about 3"" in the center without breaking the bond to the board, or causing any cracks to appear in the magnesia cement. The ability to resist fire as well as the possession of insulating qualities are also desirable characteristics of magnesia cement stucco.Magnesite cement stucco should be applied in two coats, each 1/4"" thick on various surfaces such as wood lath, metal lath, sheathing board, brick, hollow tile, or stone; care being taken as regards the presence of lime, unless the same has been rendered, or become inert as with very old, walls. The first coat made up to a consistency that works easily under the trowel is applied in the usual manner. No water should be added to the liquid chloride as it would alter its density, and injure the work. The second or finishing coat is then applied. The aggregates are different in each, and no other dry material should be added to them as they come to the trade. The cement may be applied in zero weather without damage. Setting is quite slow under such conditions, but the cement ultimately becomes hard. It should always be applied to a dry surface excepting that under certain conditions it is desirable to apply a solution of magnesium chloride before using the stucco."

Dec 1, 1919

To provide accurate navigation and control of continuous mining systems.

Jan 1, 1996

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By I. AITKENS

Tourmalines are among the most beautiful of all the semiprecious stones, and are unsurpassed even by corundum in variety of hue. The stones most suited to jewelry purposes are those comparatively free from iron. One reason for the fact that the tourmaline has advanced rapidly in public favor in this country is that it is found in California in great profusion and of extraordinary quality. The superb green and especially the pink crystals found at Pala and Mesa Grande in San Diego County, Calif., are deemed superior to tourmalines from all other localities.

Nov 1, 1931

By Webster S. Anderson

The design, development, and testing of hydraulic props to provide a lightweight, high strength, recoverable unit is described. Modifications in design incorporating threaded components resulted in the development of a lightweight hydraulic prop fabricated from aluminum alloy tubing. This new design facilitates interchange and replacement of component parts, and the physical properties of the material are not changed as they are when welding is required. The new prop is 65,000 pounds and has a maximum load capacity of a lower weight-to-load capacity ratio than the hydraulic props now available.

Jan 1, 1967

By L. C. IlsLey, R. A. Kearns

As the use of electricity becomes more and more general in mining opera- tions, interest in regulations governing its application becomes greater. During the past year the electrical section of the Bureau of Mines has made a study of State regulations now in force relating to the use of electricity in coal mines. Technical Paper 271, entitled "State Mining Laws on the Use of Electricity in and about Coal Mines", has been published as a result of this study. The present paper represents a compilation of all laws relating to accident prevention with respect to electrical circuits. This group of regulations is perhaps the most important of any that relate to safety in coal mines. Its importance is shown by reference to accident statistics in Bulletin 115, (Fay, A.H., Coal-Mine Fatalities in United States, 1870-1914, Bureau of Mines, 1916), which show that about 77 per cent of the fatalities due to electricity in and about coal mines were caused by direct or indirect contact with trolley or other power circuits. In actual number this means that of 710 men killed by electricity, 546 were killed by contact with electric wires. Undoubtedly, a large percentage of these accidents might have been prevented had the wires been properly guarded. The compilation follows:

Mar 1, 1921

By Oliver Bowles

Slate possesses many admirable qualities, not only as a roofing material, but for blackboards, electrical switch boards, and for various structural uses such as stair trends, floor tile, baseboards, and sanitary enclosures. The American slate industry was established manor years ago, and has made remarkable progress, particularly during the past five years. One of the chief drawbacks to more rapid expansion is the high percentage of waste which reaches 75 to 94 per cent of gross production. Much of this waste is duo to rock imperfections over which man has no control, but a careful study of tae industry by the Bureau of Mines over a period of years indicates that an undesirably large percentage of the marketable slate is wasted in the processes of quarrying and manufacture. The initial step in quarrying slate is to separate from the solid ledge masses of a size that ray be conveniently removed from the quarry. This first step entails a greater waste of material than any subsequent process, and, therefore, invites the most earnest effort toward waste reduction. Attention has consequently been directed toward possible improvements in methods of making primary cuts in the quarry floor. A study of European practice with the wire saw, together with theoretical consideration of its advantages, convinced the writer that it possessed sufficient merit to justify its use as a primary slate cutter in American quarries. No practical conclusion in this matter could be reached except by experiment. Therefore, the desirability of obtaining equipment and trying it out under actual conditions of operation was urged upon operators. While no doubt the equipment could be readily manufactured in America, it had already been developed to the point of practical use in Europe; therefore the writer urged the desirability of purchasing one completely equipped wire saw in Europe, and determining through tests whether it gave sufficient promise of success to warrant its manufacture in America.

Jan 1, 1927

By J. A. Rowland

Manganese-copper alloys containing 60 percent or more electrolytic manganese exhibit an unusual combination of high vibration damping capacity with good strength properties. Properties of the pure alloys were first studied in the laboratories of the Federal Bureau of Mines and have been described in a series of technical papers1/ published from 1941-49. The unusual characteristics of these manganese-copper alloys attracted the attention of research metallurgists and several additional investigations have also been reported in the literature.2/ The engineer, also, was attracted by the combination of high strength and high vibrational damping capacity possessed by these alloys. A wide field of application in structural and machine design was obvious. However, serious difficulties encountered in commercial fabrication of structural or machine components from the alloys retarded attempts at their practical utilization. For this reason the Federal Bureau of Mines, in cooperation with the United States Navy, Bureau of Ships, undertook a program designed to develop practical methods for fabricating a selected group of the high-damping alloys. It is the purpose of this paper to summarize a part of that investigation in a form suitable for use by the metallurgist interested in commercial fabrication of the alloys.

Jan 1, 1955

By Noel N. Moebs

The Bureau of Mines conducted five reconnaissance magnetometer traverses across a small abandoned chromite mine in the State Line district of Pennsylvania and Maryland to determine the geophysical response of the area. The results indicate that more extensive geophysical surveys of the region might establish some worthwhile guidelines for chromite exploration. While chromite only rarely can be detected directly by magnetic methods, there is a possibility that geophysical signatures in the adjacent host rock could provide some guidelines for further exploration. Prior to 1875, all the chromite produced in the United States came from the State Line district, and the potential for discovering additional podiform deposits could be significant. Virtually no state-of-the-art geuphysical or geochemical studies have been conducted in this district since World War II and sizable areas remain undeveloped and suitable for exploration. While the results reported in this paper are not supported by drilling, it may encourage others to investigate the area more fully for improved methods of detecting subsurface podiform chromite deposits. New theories on the emplacement of ophiolites also could contribute to an assessment of the chromite potential of the serpentinite belt.

Jan 1, 1991

By G. W. Reimers

Metastable pyrophoric wüstite (FexO, with x between 0.89 and 0.95) was found to be much easier to grind to colloidal state than were its stable disproportion products magnetite or iron. The grinding of polycrystalline magnetite appears to be complicated by the magnetic flocculation arising from interparticle attraction. This is superimposed on the attraction of a fluctuating electric dipole for a neighboring induced dipole. More than 85 pct of the tumbling time was saved by grinding antiferromagnetic wüstite instead of the ferrimagnetic oxide of iron (Fe304). Disproportionation of colloidal wüstite to the stable ferromagnetic and ferrimagnetic colloidal particles of alpha-iron and magnetite, respectively, was accomplished rapidly at temperatures above 250° C but below 570° C, the eutectoidal stability point of the wüstite phase.

Jan 1, 1972

By W. D. Bensema, J. W. Adams

A portable, multichannel battery-operated mine-permissible measurement system was developed to measure the rms magnetic-field noise spectrum in the frequency range from 100 Hz to 375 kHz. During each measurement, the entire spectrum is measured simultaneously through the use of time-domain recordings which are later analyzed by Fast Fourier Transform processing. Dynamic ranges of 60 dB in a 125 Hz bandwidth are obtained for spectra covering the range from 100 Hz to 100 kHz. The method also allows a three-dimensional display of the way spectrum occupancy changes with time. Calibration and correction procedures allow absolute field strength measurement with an uncertainty of not more than 3 dB. We feel that further analysis of the system errors will allow this uncertainty to be reduced to less than 1 dB. Ambient magnetic field noise spectra covering frequencies from 100 Hz to 100 kHz are given for several underground coal mine locations. Examples are also given of magnetic field noise on the surface above the mine, noise in the mine face area, noise radiated by specific equipment, the voltage spectrum found on a 600 V dc trolley wire, and noise picked up simultaneously on loops and on roof support bolts.

Jan 1, 1973

By John A. Davis, John Gross

This paper is one of a series giving the results of metallurgical tests conducted by: the Alaska station of the Federal Bureau of Iſines, on the recovery of gold from the black sands of placer clean-ups. The data given in this report were obtained from tests on a lot of black sand from a property located on St. Patrick Creek, Fairbanks mining district, Territory of Alaska. This property comprises the Sagan Fraction and adjoining bench claims, and is being operated by J. A. Lillie. The sand ad already been treated at the mine by amalgamation. A sample taken by Mr. Lillie and assayed at the station showed that the gold still remain ing amounted to ll cents per pound. As this gold content was sufficiently high to justify further treatment of the same, 770 pounds were shipped to the station for testing. The reader will note that the gold content is given in cents per pouni, rather than per ton. This is in conformity with practice in the district in valuing black sands, as the quantity obtained at any one time is small, much less than one ton. . The sand consisted principally of schist and quartz, with very little ilmenite and garnet; and no magnetite or sulphides. Most of the gold present as contaminated with quartz, as the free particles of gold had been removed by amalgamation at the mine.

Sep 1, 1920