Search Documents

By Gerald A. Munson, E. P. Barrett

Rapid and accurate estimation of the proportions of mineral in rock mix- tures is essential in mineral-dressing research and industrial operation. Estimation of the proportions of potash and soda feldspars in ground pegmatite material by casual observation is almost impossible and may be tedious or even difficult by petrographic examination. Chemical analysis may not be an accurate measure, as pegmatite rock may contain the following minerals:

Jul 1, 1947

A major hazard to workers in underground mines is fire and the resulting contaminated air. Fire reaches miners thousands of yards away with carbon monoxide gas and other toxic fumes. The same ventilation system that furnishes fresh air to miners can also be the vehicle to carry contaminated air to remote locations. To reduce these problems, the U.S. Department of the Interior's Bureau of Mines entered into Contract H0242016, "Mine Shaft Fire and Smoke Protection System," with FMC Corporation, Santa Clara, California, to evaluate mine shaft fire and smoke hazards and to develop and demonstrate a low-cost, reliable mine shaft fire and smoke protection system that would be applicable to a majority of metal and nonmetal mine shafts, including raises and winzes, especially in deep mines.

Jan 1, 2011

By R. A. Beall

Consumable-electrode arc melting is now accepted throughout the industry as the best method for producing ingots of zirconium, titanium, molybdenum, and their alloys. In addition, the technique is widely used in laboratories for fusing samples of such metals as hafnium, chromium, tantalum, columbium, and thorium. The production of consumable electrodes from these metals presents some rather difficult problems, the accepted industrial solution being the use of heavy powder-metallurgy-type presses. This paper summarizes information on fabrication of consumable electrodes by this and alternative means, such as sintering, nippling, and welding lightly pressed compacts of scrap metal. A possible saving of considerable capital investment is shown in the case of sintered compacts. The electrical circuit components of a pilot sintering unit are analyzed. INTRODUCTION The consumable-electrode arc-melting process has been accepted by most of the industry as the best method at present for producing high-quality pure or alloy in-got from sponge titanium or zirconium. This technique is not particularly new, having been patented by Von Bolton (l)3/ in 1909 for melting tantalum. However, it has been applied to industrial-scale operation only in the last few years. Among the important contributions to this technique are the work of Kroll (2) and Parke and Ham (3) and the work reported by the Office of Naval Research (4). The Bureau of Mines-has added considerably to the knowledge of this process (5-9).

Jan 1, 1956

By Oliver Bowles

From the most remote periods of civilization stone has been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns), or single markers, to great obelisks and pyramids or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1650 at an estimated cost of $50,000,000 or more and is today an object of unusual interest for travelers. Other magnificent memorials both ancient and modern are to be found in many lands. No sharp line can be drawn between buildings and monuments, because the larger types of memorials such as the Bok Singing Tower, Lincoln and Jefferson Memorials, and mausoleums of various types have features in common with buildings. However, great care must be exercised in selecting a site for a quarry that will produce acceptable monumental stone because appearance as well as quality is of prime importance. The deposit must be of uniform texture and attractive color and must be notably free of knots, hairlines, impurities, incipient seams, or other defects. Many memorials are of polished stone, and spots or streaks that might be virtually Invisible on a natural rock face will appear distinctly on a polished surface. Hence, stone to be polished must be selected with unusual care. However, less flawless stone may be used for hammered surfaces.

Jan 1, 1955

By Alla D. Mah

The heat of combustion of TaC0.996 was determined by oxygen bomb calorimetry to be -302.8 ±0.4 kcal/mole. The corresponding heat of formation of TaC0.996 is -35.4 ±0.5 kcal/mole, and the calculated heat of formation of TaC1.00 is -35.5 ±0.5 kcal/mole.

Jan 1, 1965

By K. D. Luxbacher

Understanding methane emissions in underground coal mines is critical for a safe and productive mine. In addition to reasonable estimation of initial coalbed reservoir parameters, it is also crucial that changes in effective stress due to mining and pore pressure reduction are taken into account due to their effects on porosity and permeability. Primary parameters for estimation of emissions or modeling of the mining environment for this purpose are porosity and permeability which can change dramatically as a result of stress redistribution associated with mining and gas desorption from a large coal volume. These parameters affect the emission rates and ventilation requirements, as well as water inflow into the working environment. Stopping leakage, on the other hand, is a secondary stress dependent factor in estimation of emissions, as convergence of the roof and floor strata, compromising the integrity of the stopping, may result in leakage, making prediction of ventilation requirements difficult. This paper aims to examine the effects of porosity and permeability changes of the coal seam on methane emissions in an underground continuous miner section. The models were developed and executed in a dynamic fashion to simulate an advancing section. Through this process, the changes of effective stress in coal, particularly their change paths, on porosity and permeability were incorporated into the models and methane emissions, concentrations, air requirements, water inflow and possible leakage from the stoppings were investigated using a conventional coalbed methane reservoir model.

Jan 1, 2009

By E. J. Gleim

Contact with trolley wire in the mines of the United States has taken a considerable toll of life throughout the years that trolley locomotives have been employed as a means of' transportation. A study3/ of the records over a 15-year period for one State alone showed that, of 98 fatalities resulting from contacts with electrical circuits and equipment, 75 were caused by direct or indirect contact with unguarded trolley wire in coal mines. The law relating to guarding trolley wires in the mines of this particular State, as amended in 1935, reads in part as follows: "All trolley wires carrying 220 volts or more, and less than six feet six inches above top of rail, must be guarded at all points under which men and animals are required to pass***,'" The natural conclusion to be drawn from such records is that lack' of guards or shields must be held responsible for these fatalities. As a preventive measure, it has been advocated that every foot of trolley wire in mines should be guarded. Although some such drastic steps may appear to be amply justified, closer examination of the records nor this and other coal-mining States shows that absence of guards is not entirely responsible; but rather that other factors, such as carelessness and neglect it the observance of certain well-established simple rules concerning installation and location of trolley wires, also are responsible. In other words, if trolley wire is installed carelessly and its maintenance is neglected, it should not be expected that the mere installation of guards will overcome such carelessness and neglect. This publication discusses Various types of guards that have been used in Coal and metal mines of this country, together with related steps bearing upon the problem of 'preventing shock and fatalities from contacts with trolley wire. The material herein contained is taken largely from Information Circular 6577,4/ now out of print, and has been revised to include some types of guards that have been used in metal mines, together with a discussion of guard materials not covered in that publication.

Jan 1, 1945

By BUREAU OF MINES

Atentative Draft of a standard smoke abatement ordinance has been prepared by a joint committee made up of representatives of the American Society of Heating and Ventilating Engineers, the Stoler Mamufacturers Association, the American Civic association, and the Fuels Division of the American Society of Mechanical Engineers. The Committee is desirous of obtaining helpful criticism and suggestions about this ordinance, which should be mailed to the chairman, Dr. O. P. Hooi, Bureau of lines, ashington, D. C. Te personnel of the committee is as follows: Dr. O. P. Hood, chairman, and Henry Kreisinger, representing the Fuels Division of the American Society of Mechanical Engineers; P. J. Dougherty, representing the American Society of Heating and Ventilating Engineers; Lloyd R. Stowe, representing the Stoker Mam- facturers Association; Everett L. Hillard, representing the American Civic Ascociation; and Osborn Monnett and Harry 3. Meller, members at large.

Mar 1, 1930

By Maria I. De Rosa

Coal mine fires pose a constant danger to the safety of miners and to their livelihood. Underground mine fires pose an added hazard because of the confined environment with remote exits. Enactment of safety regulations [30 CFR2 75 and 771 for under- ground coal mines and surface coal operations has greatly improved the safety of miners. However, mine fires and fire injuries remain serious hazards for all coal mining operations. This report analyzes mine fires and fire injuries for all U.S. coal mining categories (underground coal mines, surface of underground coal mines, surface coal mines, and coal preparation plants) during 1990-1999. Fires involving contractors are also included in the analysis. Similar analyses (for underground coal mines only) by the former U.S. Bureau of Mines (USBM) were reported by McDonald and Pornroy [I9801 and Pornroy and Carigiet [I9951 for 1950-1977 and 1978-1992, respectively. For comparison purposes, data for 1978-1 992 are mentioned in the "Underground Coal Mine Fires" section of this report. Detailed analyses of mobile equipment fires for all underground and surface coal and metal/nonmetal mining categories during 1990-1999 have recently been reported by NIOSH [De Rosa 20041. Risk rate values (fire and injury risk rates) for the 10-year period (1990-1999) and for five successive 2-year periods within the 10-year period are derived. Risk rate values for individual states for the 10-year period are also derived. Other variables by state and time period include employees&apos; working hours, lost workdays, and coal production (underground and surface coal mines only). The number of fire fatalities is reported by time period. Variables such as ignition source, method of detection and suppression, equipment involved, location, and burning material are reported by five 2-year periods only. Furthermore, the number of fire injuries per number of fires causing injuries and total fires has been analyzed by year, ignition source, equipment involved, and location. For comparison purposes, the major fire and fire injury findings for all coal mining categories have been reported. The data in this report were derived from "Injury Experience in Coal Mining" [MSHA 1991a, 1992,1993,1994a, 1995a, 1996, 1997, 1998b, 1999c, 20001, "Fire Accident Reports" [MSHA 199 1 b,c; 1994b; 1995b,c; 1998a,c,d,e,f; 1999a,b,d,e], MSHA "Fire Accident Abstracts" internal publications, and verbal communications with mine personnel. Mining companies are required by 30 CFR 50 to report to MSHA all fires that result in injuries and fires that are not extinguished within 30 min of discovery. A small number of fires lasting <30 min without injuries reported in the "Fire Accident Abstracts" have been included in this report. The analysis in this report will provide the National Institute for Occupational Safety and Health (NIOSH), the Mine Safety and Health Administration (MSHA), and the mining industry with a better understanding of the causes and hazards of mine fires and fire injuries. It will also form a basis for developing future fire research programs.

Jan 1, 2004

The following are abstracts from papers presented at the 4th Symposium on Respirable Dust in the Mineral Industries and· were produced through research funding under the Generic Mineral Technology Center for Respirable Dust. Full articles appear in the proceedings published in July 1996 in Applied Occupational and Environmental Hygiene. (Volume 11, Number 7). The two addresses included in the proceedings point to the progress, prospects, problems, and perspectives on control of respirable dust and dust-related disease in the mineral industries. The symposium papers deal with respirable dust issues that are longstanding such as characterization, health effects, control of airborne coal dust, new and emerging issues such as iron toxicity, diesel particulates, and sampling. The papers were grouped into the following topics: continuous dust monitoring, encompassing the development of a fixed-site monitor that will provide continuous information on instantaneous and time-weighted respirable dust concentrations; mechanisms involved in the generation of dusts in mine environments, important for dust control at the source; characterization and control of diesel emissions (particularly diesel particulates) in mine atmospheres; mining systems effects and models; dust control in mine working faces and in milling environments; characterization of the physical, chemical mineralogical, and biological properties of the dust and their relevance to health effects and sampling; dust-lung interactions, encompassing results from several biomedical studies dealing with acute and chronic inhalation of airborne dusts and associated lung responses; the role of iron in causing lung injury; and therapeutic strategies for ·the control of pulmonary disease. All papers submitted to the organizers were peer-reviewed. In the proceedings, we have not differentiated among the platform and poster papers; rather, they have been grouped into the above topical areas. Taken together, these papers reveal significant progress in the control of dust generation, characterization of dust, understanding of dust-lung interaction, and mining and milling practices to reduce dust exposure - all essential for reducing dust-related occupational hazards at the workplace.

Jan 1, 1998

By R. V. Ramani

"In Part 1 of this paper, published in the August 1995 issue of Natural Resources Forum, a review of several mining disasters around the world established the complex nature of their causation and their catastrophic effects. The involvement of human beings, either through acts of commission or omission, was highlighted. In Part 2, a discussion of the various approaches to disaster control, mostly as practised in the USA, is presented. A systems approach to disaster prevention incorporating elements of hazard identification, mine design, emergency response and post-emergency audit is presented.In the USA the role of government in the affairs of its citizens is continually growing. This role is intended to ensure an unimpeded pursuit of happiness and prosperity by the population and to curtail actions which are restrictive or harmful to the citizenry. The passage of a legislation is an indication that it has been decided through the established process that the activities covered by the legislation should receive appropriate consideration. The enactment of the Coal Mine Health and Safety Act of 1969 (The 1969 Coal Act), the Mine Safety and Health Amendment Act of 1977 (The 1977 Mine Act) and the Surface Mining Control and Reclamation Act of 1977 (The 1977 Surface Mining Act), was specifically intended to further the role of government in the health, safety and environmental affairs of the mineral industry.Currently, the federal government's responsibilities for mine safety and health are divided among three agencies: the Mine Safety and Health Administration (MSHA) in the US Department of Labor, the Bureau of Mines (USBM) in the US Department of the Interior and the National Institute for Occupational Safety and Health (NIOSH) in the Department of Health and Human Services (National Research Council, 1981). MSHA is responsible for issuing and enforcing mine safety and health regulations, for training miners and for responding to mine emergencies. The Bureau of Mines is responsible for conducting research on mine safety and on the technological means for reducing health and safety hazards in mines. NIOSH conducts research relating to miner health, and together with MSHA, tests and certifies devices used to detect hazardous materials in mines and protective equipment used by miners. NIOSH also plays a public health role in that its activities in mining include health hazard evalua¬tions, general mining surveillance as mandated by law and medical surveillance including coal miner X-ray and autopsy programmes. MSHA shares with the Bureau of Mines the responsibility for integrating R&D results into operational practice. MSHA implements R&D results either by incorporating them into its own operations or by rule making that requires new practices or equipment to be adopted by the mining industry. In many instances, the Bureau's R&D results have been adopted by the mining industry without rule making."

Dec 1, 1996

By Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to melt residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-offgas handling system, and thermal oxidizer for final offgas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 lb/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kV?A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the offgas and serves as an acid gas scrubber. The clean offgas is heated to 1,800° F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 2010

By Kihong Park

A hygroscopicity tandem differential mobility analyzer (HTDMA) technique is used to determine size-effect of nanoparticles (NaCl, (NH4)2 SO4, KCl, NH4NO3, MgCl2,CaCl2) on their hygro­scopic properties (deliquescence relative humidity (DRH) and hygroscopic growth factor (GF)). The HTDMA system uses a combination of two nano DMAs and two regular DMAs to measure particle size change in a wide dynamic particle size range. Particles are subsequently analyzed with a transmission electron microscopy to investigate the potential effect of particle structure or morphology on the hygroscopic properties. We found that structural properties of NaCl and (NH4)2SO4 particles also play an important role in determination of the DRH and GF and are more pronounced at smaller diameters. Data show that the DRH of NaCl nanoparticles increased from *75% up to *83% RH at 8 nm and that their GF decreased with decreasing size. The extent to which the GF of NaCl nanoparticles decreased with decreasing size was greater than theoretically predicted with the Kelvin correction. The GF of furnace-generated NaCl nano­particles that have pores and aggregate shape was found to be smaller than that of atomizer-generated particles that are close to perfectly cubic. For the case of atomizer-generated (NH4)2SO4 nanoparticles, we observed no signi?cant size-effect on their DRH, and the measured GF agreed well with predicted values using the Kelvin correction. For furnace-generated (NH4)2SO4 nanoparticles, a gradual growth at moder­ate RH without noticeable deliquescence behavior occurred. Their TEM images showed that contrary to atomizer-generated (NH4)2SO4 nanoparticles the fur­nace-generated (NH4)2SO4 nanoparticles are not perfectly spherical and are often aggregates having pores and holes, which may favor holding residual water even in the dried condition. For atomizer-generated KCl, MgCl2, and CaCl2 nanoparticles, we observed no signi?cant size-effects on their DRH and GF for the mobility size as small as 20 nm.

Jan 1, 2008

By G. L. Oldright, Virgil Miller

"INTRODUCTION The first ten papers of the series on smelting in the lead blast furnace described the operation at the custom smelter of the International Smelting Co., Tooele, Utah, and at the plant of the Bunker Hill Smelting Co., Kellogg, Idaho, which handled a very rich lead concentrate. These previous papers may be considered a picture of the traditional lead smelter treating custom ores and of the smelter that will treat the type of product likely to be made in the future - lead concentrates of an increasingly rich grade.The great plant at Trail is of special interest to those smelting lead products containing much zinc and faced with the necessity of transforming all of their byproducts into commodities which may be sold profitably. The plant is equipped to produce electrolytic zinc, lead, copper, silver, bismuth, and cadmium. Part of the sulphur evolved from treating the ores is converted into sulphuric acid. Complete fertilizers for agricultural purposes are also produced.The smelter of lead ores has long considered that zinc is one of the most difficult ingredients that he has to handle. Even with the gretat improvement in flotation practice today, the residues from electrolytic zinc plants leaching zinc concentrates must still be smelted for their lead content. Of the total gangue material not separated from the lead concentrate sent to the smelter, zinc is still one of the most notable in percentage. The most successful way of coordinating the over-all operations of a concentrator, an electrolytic zinc plant, and a smelter provided with a plant for re-treating the blast-furnace slag for its lead and zinc content must be of interest to many treating complex ores.ACKNOWLEDGMENTThe data in this paper were collected in cooperation with the Consolidated Mining & Smelting Co. of Canada, Limited, and its entire technical staff. Detailed acknowledgments of assistance received are given in the papers from which this one is briefed."

Sep 1, 1934

By K. K. Kelley

"In an earlier consideration of the vapor pressure of iron 3/ it was found necessary to estimate the specific heat of gaseous iron to write satisfactory free-energy-of-vaporization equations for the several forms of iron. That the specific heat of gaseous iron will exceed greatly the classical value of Cp = 4.967 calories per gram-mole per degree is evident from even a cursory Lamination of its spectrum. The two lowest energy states are separated by only 416 cm-1, which is small enough so that the second state is effective, theoretically, at below room temperature. Such phenomena are by no means uncommon, but, while they have been recognized with substances that ordinarily are encountered as gases, classical gaseous specific--heat values still are used, often without question, for the vapors of metals and other elements that are solids under ordinary conditions. The following calculations for iron and copper gases are presented to illustrate the sort of deviations from classical values that are encountered with metal gases.The methods employed in calculating from spectroscopic data of thermodynamic quantities such as specific heat, entropy, and free energy have been described, in detail by Giauque 4/ and others. These will be briefly reviewed here. It is customary to separate the translational energy of a molecule from the rotational, vibrational, and electronic energies. In the case of monatomic gases, only translational and electronic Energies are involved. The classical expression for the specific heat of a mona¬tomic gas, Cp = 4.967, deals only with energy stored in the molecule as translational energy and consequently is valid only in temperature ranges in which no appreciable number of molecules undergoes a change in electronic state."

May 1, 1937

By Roy H. Grau

Increased awareness of a healthy work environment is common to all industries and the stone industry is no exception. The presence of operating diesel equipment, welding, stone production blasting, and silica dust in a working environment all contribute to air quality issues in underground stone mines. Particularly recognized is the exposure of workers to diesel particulate matter (DPM). Recent regulations call for a DPM standard of 160TC ug/m3 (TC = Total Carbon). The National Institute for Occupational Safety and Health (NIOSH) has conducted research to improve the ventilation of these mines and consequently reduce the exposure of workers to harmful airborne contaminants. The results have shown that the ventilation of underground stone mines can be significantly enhanced using improved ventilation controls and techniques. Large-opening stone mines present specialized ventilation challenges because their entries are much larger than in other types of mines. Most stone mines have entries about 40 feet wide and up to 30 feet high, with bench areas that may extend even higher. These large entries present the positive opportunity to move large air quantities at relatively low mine fan pressures resulting in lower fan horsepower and reduced operating costs. However, the difficulty in ventilating large-opening mines is that even with large air volumes, the air velocity is often less than 100 feet/minute. Higher ventilation velocities more quickly dilute and remove contaminants from the face areas. Higher ventilation airflow velocities can be achieved by effective ventilation planning and proper choice of ventilation fans.

Jan 1, 2009

By John A. Organiscak

Laboratory and underground studies were conducted by the Bureau of Mines to evaluate the effectiveness of a water-powered scrubber and a brattice partition to create a clean split of air for longwall workers at the tailgate. In simulated laboratory tests, the system was very effective in creating a clean split of air. Observed system efficiencies were 74 and 84 pct with induced airflows of approximately 2,000 and 2,500 cfm, respectively. Underground evaluations indicated that the system was capable of reducing respirable dust at the tailgate. The first underground evaluation resulted in protection efficiencies of 30.7 and 42.5 pct at scrubber water pressures of 150 and 450 psig, respectively. A 33.7-pct protection efficiency was observed in the second underground evaluation with a modified partition and the scrubber operating at 250-psig water pressure. To be most effective, the system should have the scrubber operating at a flowrate of 10 gpm at 500 psig to deliver a maximum quantity of cleaned air behind a well-sealed partition.

Jan 1, 1983

By John J. Sammarco

As part of a project to automate coal extraction, computer control of a continuous mining machine test bed has been developed and tested by the Bureau of Mines. A computer system and control software were developed for accurate positioning of the conveyor elevation and swing, stabilizer jack, gathering head, and shear elevation. Tramming actions are also controlled by the computer. The computer system was designed to access data from sensors installed on a continuous miner and to interface with the existing control circuits of the miner. Testing in free space was used to characterize the operation of the machine. From this information, control algorithms were written and stored in the computer. The ability to control each function of the continuous miner with a high degree of accuracy and stability was successfully demonstrated in a series of tests in free space and in mining a block of simulated coal. In the mining of simulated coal, the cutting drum was instructed to position the shearer at the top of the block and shear down to the bottom under closed loop control. The cutting drum came within 0.27 in of the top and within 0.49 in of the bottom of the block for this shearing test.

Jan 1, 1988

By Richard D. Miller

The helium resources base of the United States was estimated by the U.S. Bureau of Mines (Bureau) to be 894.6 Bcf as of January 1, 1989. These resources are divided into four categories in decreasing degree of assurance of their existence: (1) helium in storage and in proved natural gas reserves, 282.4 Bcf, (2) helium in probable natural gas resources, estimated at 237.7 Bcf, (3) helium in possible natural gas resources, estimated at 263.1 Bcf and (4) helium in speculative natural gas resources, estimated at 111.4 Bef. These helium resources are further divided into depleting and nondepleting, with the helium in storage being in a classification. The depleting resources are those associated with natural gasfields that are, or will be produced for the natural gas they contain. Almost all of the helium in potential (probable, possible and speculative) natural gas resources is included in this classification. These depleting resources are estimated to contain 775 Bcf of the total helium resource base. Helium resources contained in nondepleting natural gas resources, i.e., those in shut-in, abandoned, or otherwise nonproducing natural gas fields, are estimated to total 84 Bcf There is 35 Bcf of helium in storage in the Federal Government-owned Cliffside Gasfield near Amarillo, TX.

Jan 1, 1990

By S. H. Katz, J. J. Bloomfield

Fires in zinc dust have sometimes given particular trouble owing to their resistance to extinguishers and the liability of explosions . Similar problems , notably with aluminum dust* , have previously been subjects of investigation by the Bureau of Mines .

Mar 1, 1922