Search Documents

Provide d comprehensive source of up-to-date information about technology for revegetating coal mined lands. Approach A great deal of activity and research in the field of coal mine revegetation has been reported in technical literature, both before and after the passage of Public Law 95-87, the Surface Mining Control and Ruclamation Act of 1977 (SMCRA). This information is widely scattered throughout books, scientific journals, periodicals, Government reports, and other sources, and there has been a need to develop a method of accessing it quickly and efficiently. At the request of the Office of Surface Mining Reclamation and Enforcement which promulgates and enforces regulations implementing the act, the Bureau of Mines has prepared a document that identifies literature relevant to coal mine revegetation. Most of the literature available on this subject has been published during the past 15 years. To tap this reservoir of information, 14 data bases were accessed from DIALOG SDI (Selective Dissemination of Information) Service using three keyword combinations (surface mining and reclamation, strip mining and reclamation, and revegetation). This procedure generated over 7,000 listings. The U.S. Department of Energy's ENERGY data base was selected from the 14 DIALOG bases, both for its large number of listings and for its broad coverage of literature. This data base contains all the unclassified information that passes through the Technical Information Center of the Department of Energy, including reports, journal articles, conferences, patents, books, monographs, theses, and engineering materials relating to energy development.

Jan 1, 1986

By R. H. Nafziger

As part of its program to help decrease the dependency of the United States on foreign imports of nonfuel minerals and to devise technology for the efficient and economic use of domestic resources, the Bureau of Mines smelted and sulfation-leached an ilmenite from northern Minnesota. The objective was to assess the feasibility of preparing chlorination-grade titanium feedstock. The concentrate was smelted with woodchips, coke, and soda ash in 91-kg-and 1-metric ton (mt)-capacity electric arc furnaces to form Ti-rich slag and commercial-grade pig iron. The slag contained from 67 to 77 wt pct titanium oxides and from 1.8 to 7.2 wt pct iron. Sulfation occurred in a 4.5-kg/h moving-bed reactor using S02-air mixtures at temperatures of 8000 to 8500 C to form soluble salts of the Ca, Mg, Mn,and Na impurities, which cause plugging of fluidized-bed chlorinators. Subsequently, the sulfated slag was leached in acid to remove the soluble sulfates. The final product from small-scale testing contained up to 95.5 wt pct Ti02, a minimum of 0.6 wt pct Fe, and a minimum total of 0.3 wt pct of the four impurities of interest. The final product meets charge specifications for chlorination. However, more large-scale testing is necessary.

Jan 1, 1987

By W. E. Lamont

The Federal Bureau of Mines conducted research to develop methods of removing phosphorus from the earthy, calcareous hematite ores of the Birmingham, Ala., iron district while simultaneously improving the grade and recovery of the iron values prior to furnacing. An attempt was also made to identify the phosphorus minerals present in the ores. The ores contained about 36 percent iron, 12 to 16 percent CaO, 15 to 20 percent hydrochloric acid insolubles, and 0.30 to 0.36 percent phosphorus. Fractions containing 5 to 15 percent phosphorus were isolated from the ores. Collophanite, Ca3P2O3?nH2O, a member of the apatite group, was the only phosphate mineral identified. Beneficiation methods using flotation and reduction roasting with magnetic separation yielded good grade iron concentrates, but were not as effective for reducing the phosphorus content of concentrates. Reduction roasting followed by fine grinding, magnetic separation, and acid leaching gave iron concentrates containing 62.5 percent iron and 0.04 percent phosphorus with an iron recovery of 82.9 percent and a phosphorus rejection of 93.7 percent. Reoxidation of reduced magnetic concentrates followed by acid treatment gave iron concentrates containing 58.1 percent iron and 0.02 percent phosphorus with 89.6 percent recovery of the iron and 96.5 percent rejection of the phosphorus.

Jan 1, 1973

By H. H. Dewing

The Bureau of Mines conducted a laboratory-scale investigation of a technique that produces zinc sulfate and elemental sulfur from sphalerite concentrates by reaction with sulfuric acid at 175° to 200° C and ambient pressure. The objective of the investigation was to develop a hydrometallurgical method of producing zinc from sulfide concentrates that does not generate sulfur dioxide pollutants. Reaction with 80-to 85-pct sulfuric acid produced 4 moles of sulfur for every 3 moles of sphalerite reacted, with minimal production of sulfur gases under optimum conditions. More than 98 pct of the zinc was recovered as zinc sulfate after 3 hours at 175° C. The reaction mixture was leached with simulated spent zinc electrolyte containing 13-pct sulfuric acid to recover zinc sulfate from the insoluble, high-sulfur residue. Neutral zinc sulfate, which is required for electrolysis, was separated from the sulfuric acid solution by crystallization as ZnS04?7H20 at -10° C. Up to 80 pct of the water in the recycled electrolysis solution was removed by the crystallization process; evaporation was used to further concentrate the sulfuric acid for reuse in leaching sphalerite. Advantages of the proposed method over conven-tional roasting and leaching include virtual elimination of sulfur dioxide, production of a solid sulfur byproduct, and higher zinc recoveries due to elimination of zinc ferrite losses.

Jan 1, 1978

By M. G. Pelipetz

High-pressure, high-temperature hydrogenation of coal has been known and practiced for many years. A full' understanding of the mechanism in this process by which coal is converted to oil and gas must rest on a critical interpretation of the manner in which external variables influence the rate and the course of the coal-hydrogenation reactions. Same Bureau of Mines studies on the effect of temperature, catalyst, and rank of coal on these reactions have been published. The effect of pressure was not studied in this earlier work, and the effect of reaction time was complicated by the interruption of long reaction periods in order to refill the autoclave with hydrogen. It is the purpose of this paper to present data from more recent autoclave experiments that extend the results of Storch, et al, on the kinetics of coal hydrogenation. These data must be explained by any comprehensive theory of coal hydrogenation; their detailed evaluation, however, will be deferred until a later publication.

Jan 1, 1949

By D. B. Dow

The presence of sulphur compounds in petroleum and its products is, generally speaking, undesirable, and the problems involved in removing such compounds are of great importance to the petroleum refiner and to the manufacturer of gasoline. There are several types of these compounds which are dissimilar in physical and chemical characteristics, as evidenced by different objectionable features which they exhibit, and special treatments have been developed to meet conditions existing in various products. This paper deals with the treatment of natural-gas gasoline for the removal of certain sulphur compounds which, if not removed, impart on objectionable odor and in addition badly discolor the product. The presence of this particular type of sulphur compounds is detected by the "doctor" test.* In some instances natural-gas gasoline is purchased on "doctor" test specifications, and the ordinary purchaser, while not buying on "doctor" specifications, is insistent in his demand for a water white product. Gasoline which fails to meet the "doctor" test, if not received by the buyer within a few weeks after time Of manufacture, may be "off color" enough to warrant a deduction from the market price.

Jan 1, 1923

By Thomas Varley

Data on the consumption of reagents used in .flotation during the year 1925, in metallurgical plants in the United States, are presented in this paper. Previous reports have covered the same subject for the years 1916, 1919, 1923 and 1924. The data contained herein show departures most radical from even the 1924 practice. Flotation has developed rapidly and on a more scientific basis than ever before. Perhaps more fundamental and useful data have been uncovered during the past two years than in all the years the art has been practiced.

Jan 1, 1926

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface coal mines by state during 1990-1999. Table 19 also shows by state the risk rates, employees' working hours, lost workdays, and coal production. For surface coal mines, 215 fires occurred in 21 states during 1990-1999. Ninety-four of those fires caused 93 injuries and I fatality (the yearly average was 21.5 fires and 9.3 fire injuries). Fourteen fires and seven injuries involved contractors. The Ewhr value was 729 x 10° hr (In = 0.026), the CP value was 6,355 x 10° st (Fn = 0.034), and the LWD value was 8,141. Kentucky had the most fires and fire injuries (45 fires and 23 injuries), followed by Pennsylvania (33 fires and 14 injuries), West Virginia (25 fires and 14 injuries), and Indiana (20 fires and 8 injuries). Among these states, Pennsylvania had the highest fire risk rate value (Frr=0.145), while Kentucky had the highest injury risk rate value (In 0.041).

Jan 1, 2004

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating, costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently cast only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting; and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

By R. D. Leitch

Beside many other damaging effects of acid mine drainage, corrosion of pipe lines and pumps frequently adds much to mine operating costs. Not only is it often necessary to install special and relatively costly acid-resistant materials, but even these may require frequent replacements. It is not unusual for ordinary steel pipe to last only a few days in some highly acid waters, while other common materials, though more resistant, frequently last only a few weeks. In the spring of 1935, local PWA authorities offered to assign a number of persons to various problems under the direction of regular employees of the Bureau of Mines. It was believed that at least some simple tests on as many different kinds of acid-resistant pipes as could readily be obtained might produce interesting and valuable information for the mining industry. This paper describes the tests and some results that have since been noted.

Jan 1, 1938

By D. Harrington

Correct ventilation of underground workings whether in coal or in metal mines consists in establishing such control of air currents that the miners may work in safety, with maximum comfort and efficiency, and without impairment of health; also in controlling the air flow so that the mine workings may at ordinary times be kept reasonably free of harmful gases or dusts, and so that in time of emergency, as when a fire or an explosion occurs, there may with minimum delay be maintained as much or as little air flow as is desired throughout the mine in its entirety or in certain parts of the mine. Control of air flow is the essential point of any mine ventilating system, and is obtained only by the installation of mechanically operated fans, and other ventilating devices such as doors; overcasts, regulators, etc. Every mine, large or small, coal or metal, should from the outset be equipped with a fan. Much has been written about natural ventilation, and many claims have been made that in specific mines or parts of mines there is sufficient natural air flow. As a matter of fact, there are actually very few if any mines, coal or metal, where natural ventilation creates atmospheres anything like adequately safe or healthful for underground workers even at ordinary times or under ordinary. conditions; and at the time of a fire or an explosion mines depending upon natural ventilation are practically helpless, and are decidedly dangerous for the unfortunates forced to be in them either at the time of the disaster or afterwards when trying to handle conditions arising from the emergency.

Jan 1, 1929

By T. D. Moore

The use of a partially slotted 6.5-inch-inside-diameter vertical pipe to remove methane from a longwall gob area at a depth of 2,260 feet in the Pocahontas No. 3 coalbed was investigated. The value of gas removed by such a pipe under free-flow conditions was found to equal the cost of the installation in this case. Approximately 25 percent of the available methane passed through the pipe without the use of an exhauster; an additional 10 percent was removed when an exhauster was employed. The diversion of methane through a vertical slotted pipe to the surface permitted the use of increased mining rates and decreased the ventilation air requirements.

Jan 1, 1972

By E. G. King

Cerium and thorium sulfides have found use as crucible materials for melting certain radioactive metals. However, thermodynamic treatment of these sulfides has been hampered by lack of experimentally derived entropy values. This Bureau of Mines report describes heat-capacity measurements between 51° and 298° K, and entropy evaluations at 298.15° K, for cerium monosulfide (CeS), cerium sesquisulfide (Ce2S3), and thorium disulfide (THS2). The entropy values, with Literature results for the heats of formation, are used to obtain free energies of formation at 298.15°K. MATERIALS The samples used in this work were supplied by Prof, Leo Brewer of the Department of Chemistry, University of California. The methods of preparation and some of the physical and chemical properties of these sulfides were given by Eastman and coworkers.3 4/ Chemical analyses, conducted in our laboratory, gave the following results:

Jan 1, 1959

By D. H. Baker

These investigations were conducted to determine the feasibility of molten salt electrorefining of zirconium scrap, offgrade sponge, and alloys under contract number AT(11-1)-475 between the Atomic Energy Commission and the Federal Bureau of Mines. Offgrade zirconium sponge having a Brinell hardness of 169 can be refined by this technique to produce metal having, consistently, a Brinell hardness of less than 90. Also, zirconium alloy scrap, approximating zircaloy-2 in composition, can be refined to recover zirconium metal with a Brinell hardness of less than 100 that is essentially free of the major alloying elements. Analysis showed that the quantities of these elements were decreased as follows: iron from 0.27 to 0.002, tin from 1.36 to 0.001, nickel from 0.02 to 0.001, and chromium from 0.12 to 0.002 percent.

Jan 1, 1961

By A. L. Engel

As a part of the program of the Rare and. Precious Metals Experiment Station, Reno, Nev., in connection with investigations of treatment methods for precious and precious-base metal ores, to further conservation and recovery of precious and base metals, tests Were made on samples from the Buzzard Mine, located in the vicinity of Placerville, Calif. These samples represented ore exposed during previous development work, in tunnels and a shaft on the property, including highly oxidized material from the surface zone and sulfide ores from depths of 150 to 300 feet. The surface samples contained little base metal and only enough gold 80 that economic exploitation of them would depend on development of a large tonnage of ore, low-cost mining methods, and satisfactory treatment methods. The sulfide samples were valuable enough to warrant further exploration and development and, if present in suitable tonnage, the installation of a treatment plant for recovery of both precious and base metals. The oxidized surface-zone samples carried 0.11 to 0.14 ounce gold per ton. Standard amalgamation and flotation tests of these samples gave low recoveries. Standard cyanidation tests indicated high consumption of lime and cyanide and gold extraction of 79.4 and 82.7 percent. Water-leaching the ore after crushing to minus 10-mesh improved cyanidation considerably. Ex-tractions of 82.7 to 85.8 percent were obtainec1 with lime consumption of 6 to 7 pounds per ton of ore and cyanide consumptions of 1 to 4 pounds. Grinding the samples to minus 200-mesh followed by water-leaching and cyanidation gave improved extractions of 91-92 percent of the gold, but with slightly increased consumptions of lime and cyanide.

Jan 1, 1949

By M. W. Von Bernewitz

Corduroy is used for saving gold in small Land large milling plants throughout the world. Investigations by the Metallurgical Division of the Bureau of Mine indicate that corduroy blankets, used with or without a trap or jig in the mill classifier circuit, often are effective in concentrating gold and sulfides, especially if the gold does not amalgamate readily and if not enough sulfides are present to warrant the use of a shaking table, flotation cells, or cyanide plant. Most cold-mining countries include several or many small miner, that produce siliceous ores low in sulfides and gold, which can easily be amalgamated or caught in traps or jigs or on corduroy and shaking tables. At these mines the ore is crushed by stamps or bill mills, and the flow sheets include plates, flotation cells, and cyanide treatment, yet probably nearly as much of the pair minerals may be recovered by the less expensive plant. A well-known western maker of mine and mill equipment asserts, as the result of considerable observation of installed plants, that old and other valuable minerals should be caught as soon as they have been released by a mill, end recommends jigs to do this. A supplier of corduroy has informed us that at some mines this material is being replaced by jigs that catch gold as fine as 400-mesh. But for the small operator, inexpensive equipment such as a corduroy table may be better adapted and give a good recovery of gold and associated minerals.

Jan 1, 1939

By B. R. Mohal, F. F. Aplan, S. Chander

"Dust abatement by water sprays involves the subprocesses of 1) collision between dust particles and water droplets, 2) adhesion of particles to droplets, and 3) engulfment of particles by the droplets. A review of the fundamental aspects of these subprocesses shows that collisions between particles and droplets are determined by aerodynamics and the size and surface charge of the particles and of the droplets. However, the adhesion and engulfment subprocesses depend upon the wetting characteristics of the particles. Although wetting agents (also known as surfactants) have been used as dust suppressants in several investigations, conflicting results are available regarding their effectiveness. In this paper, we show that these results can be explained if the effects of coal rank on surfactant adsorption and wetting characteristics are taken into account.The influence of several nonionic surfactants containing polyethoxy adducts on the wetting behavior of coal is presented. The wetting was determined by a modified Walker Test method, and contact angle measurements. The results show that the wettability of coal depends upon coal rank, structure of the hydrocarbon chain of the surfactant, and the number of ethoxy groups in the molecule.IntroductionDue to the inherent nature of the mining process, a large number of particles are generated, a portion of which becomes airborne to create dust. Dust can be aesthetically and environmentally unacceptable and it can also be explosive. Fine particles in the respirable size range ( < 5 urn) are con-sidered to cause lung diseases, namely, silicosis, pneumoconiosis, etc.(1) Several approaches to reduce dust in mine environments are practiced throughout the mining industry. These include decrease in generation of dust through improvements in mine machinery, ventilation (in which lower dust levels are achieved by dilution of contaminated air with clean air), and dust removal methods. Water sprays are most commonly used to remove dust par-ticles. Recently, scrubbers are reported to have been installed on mining machines to remove dust,(2,3) which also make use of water sprays to reduce dust."

Mar 1, 1989

By Ronald S. Conti

This paper describes technology and training that has been identified for underground emergency responders. Historically, underground mine rescue teams have only received training in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fie drills every 90 days in a smoke-free environment, this does not fully prepare them for the conditions that will be encountered in real escape situations. Therefore, it is extremely important that miners are provided with adequate technology and that training simulations are conducted in a realistic manner. A series of mine rescue training and mine emergency response development (MERD) exercises, and in-mine smoke training was developed, conducted, and evaluated by state and company teams, and by National Institute For Occupational Safety and Health (NIOSH) personnel. The training exercises were held at NIOSH&apos;s Lake Lynn Laboratory (LLL) and operating mines during the past several years. This training resulted in improved technology and training for mine rescue teams, fire brigades, first responders, and miners in general. For example, existing technologies were identified to help responders during exploration and recovery operations. These included various chemical light shapes, strobe lights, light vests, and laser pointers to identify team members. Most of these devices may be used to mark underground areas and certain mine materials. Strobe lights were used for mapping out escapeways and lasers were used to negotiate travel through smoke. Thermal imaging systems allow rescue personnel to see in darkness and through dense smoke, and allows the user to easily locate missing or trapped personnel and heated areas. A hands-free communication system showed potential for enhanced communications between team members, the fresh air base, and command center. A new team lighted-lifeline allows for flexibility in movements of team members during routine tasks and allows them to easily find their fixed position on the lifeline. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. A positive-pressure inflatable escape device (IED)/airlock, was used to isolate the "hazardous" environment from fresh air and allow rescue team members to traverse through. An inflatable feed- tube partition that can rapidly block large openings such as underground passageways or tunnels and simultaneously provide a feed-tube for high-expansion foam generators was also deployed during the simulations. These technological advancements have improved the state of readiness for rescue personnel and have increased the chances of survival for all personnel escaping from underground emergencies.

By W. D. Walker

This information circular is offered to the coal-mining industry for use as a guide in selecting, placing, and caring for fire-fighting equipment in coal mines. Its purpose is to suggest minimum requirements for fire protection underground, and it is presented with the hope that it will aid in establishing adequate standards that will provide reasonable protection against underground fires in coal mines. Potentially, a coal mine is a hazardous fire area. Coal itself is a combustible substance, easily ignited. In addition, large quantities of other combustible materials must be present in the area of operations; these include materials for roof support, track ties, doors, ventilation stoppings, lubricants, etc.

Jan 1, 1953

By W. M. Weigel

"Sand is one of the most useful and, fortunately, one of the most common mineral commodities. By far the largest proportion of the production is used in construction, including all forms of building, concrete and paving, sand for this purpose is produced in every State in appreciable amounts. Excluding send used for railroad ballast, molding sand stands not in tonnage produced, followed by glass sand.Special sands. In addition to the above, many grades of sands, with special characteristics, are used in industrial processes, and may be classed in a group as ""special sends"". This includes filter sand, sand blast sand, engine sand, abrasive send, fire or furnace send, special flooring sand, roofing sand used as a finish for prepared roofings and pottery placing sand sand blast and filter sand have been discussed in previous reports.Very few send companies depend upon the production of any one of these grades, as their source of revenue. They are generally especially prepared from the bank run of sand by different methods of screening or washing, or may, in some instances, be by-products from the production of ether grades. Many companies not now producing them might be able to supply local demands by a slight addition to their plant. In nearly all cases, they command a better price than the usual grades of building sand.Definitions and Properties.Engine sand, or traction sand, as it is sometimes called, is used to prevent the slipping of the driving wheels of locomotives, or other self-propelled vehicles, on wet or slippery rails. Its greatest use is, of course, for railroad locomotives, but street cars use considerable amounts and mine locomotives require its use. As the send must be very dry when used, most consumers have their can drying equipment, so it is often shipped damp, with its natural water content on what resulting from washing by the producer."

Oct 1, 1924