Search Documents

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite having length to diameter ratios of 3:1, 2:1, 1:1, and 0.5:1 were broken in axial compression to determine whether lateral end constraint affected the breaking strength. Steel rings bonded to the ends of the model pillars with epoxy provided, during the loading cycle, a lateral end constraint of about 17 to 30 percent of the average axial stress. The effect of this constraint was to increase the breaking strength of the rock as compared to cylindrical pillars without constraint. The percentage increase in breaking strength varied with rock type and increased as the length to diameter ratio decreased. The maximum increase in breaking strength was 35 percent for marble pillars having a length to diameter ratio of 0.5:1. A theory was developed which relates the expected constraint to the physical properties of the ring and rock.

Jan 1, 1968

By Foster Fraas

Calculations based on data related to the electrostatic precipitator illustrate the variation in the electric forces on a particle with change in position in the ionized field. The feeble forces in some separators are explained by the low field intensity at midpoint locations between the electrodes. When the particles are in contact with the exterior surface of a rotating cylindrical electrode, a high field intensity at the electrode surface combined with the image charge results in large electric forces. The permissible feed velocity increases as the square root of the electrode diameter, providing high values in efficiency and feed rate capacity, particularly in surface-to-mass ratio separations such as are encountered in secondary materials recycling operations.

Jan 1, 1971

By K. A. Johnson

Marshall and Bird have published the results of a cooperative investigation by the Bureau of Mines in which they developed a procedure for measuring the agglutinating value of coal.4 As stated in their paper, the procedure outlined was suggested by the early worn of Richters5 and Campredon,6 whose procedures were hurriedly modified to meet the need of an investigation then in progress. Since the publicatien of that paper, further work has been done in an attempt to show how the variables involved affect the concordance of the results, in order that such results may be obtained in different laboratories. Briefly, Marshall and Bird's method for determining the agglutinating value of coal consists in carbonizing an intimate mixture of 10 parts by weight of sand and 1 part by weight of coal in a porcelain crucible at a uniform temperature of 950° C. in a, vertical, cylindrical, electrically-heated furnace. After carbonization, the resultant buttons are crushed in a testing machine and the breaking strengths recorded in grams. The agglutinating value reported is the average breaking strength of 10 buttons. The coal for the test is prepared by crushing to pass a 100-mesh screen. The sand used as a diluent is sized between 40 and 50 mesh sieves with openings of 0.381 icon and 0.279 millimeters, respectively.

Jan 1, 1930

By Mackenzie Burnett

A high efficiency ejector has been developed which solves the abrasion problem associated with remote pneumatic stowing. The system can also produce cemented fills. The ejector is capable of moving the fill material over 70 ft from the injection point and filling the mine opening to the roof level for a distance of about 30 ft in all directions from the borehole. This system operates by the transfer of momentum from a supersonic air stream to the fill material. The momentum transfer results in a horizontal stream of fill material and air at a velocity of about 100 fps. The ejector fits on the bottom end of a 3 in diameter vertical pipe. Fill material is fed into the ejector at a controlled rate through a hopper mounted over the borehole. High pressure air used to operate the ejector is fed through a second 3 in diameter pipe. This system has the additional feature of mixing water in the air stream which increases the potential momentum of the air stream. Where necessary, cement can be added to the gravel to create a cemented fill. The design parameters and test results for four versions of the ejector are presented in this report.

Jan 1, 1991

By J. B. Gayle

The removal of coal particles from a slurry by flotation is made possible by the formation of stable aggregates with air bubbles of suitable sizes. The formation of such aggregates is theoretically possible only for certain favorable combinations of the solid-liquid-gas interfacial tensions. Because interfacial tensions involving solid phases are not conveniently measurable, a related variable, the contact angle, frequently is used as a measure of the floatability of various materials. Zero angles indicate nonfloatable substances, and large angles indicate substances having a high degree of floatability. During a study of contact angles for coal and substances related to coal in their similarity of response to various physical and chemical treatments, particularly flotation, carbonization, and oxidation, the reproducibility of replicate determinations taken within a 4-hour period was found to be much better than that for comparable results taken over a longer period of time. Consideration of possible causes for these differences led to an investigation of the effects of temperature variations on contact angles. References to literature revealed only a small amount of information, some of it apparently conflicting. Specifically, Sutherland and Wark4/ found that temperature variations "within limits" did not appreciably influence the angles measured for galena conditioned with potassium ethyl xanthate. On the other hand, McGlashan and McLeod5/ presented preliminary data showing that for sphalerite conditioned with potassium ethyl xanthate the angle is maximum at 25° to 35° C., depending on the pH of the system.

Jan 1, 1960

By A. B. Coates, J. E. Crawshaw

"The use of such methods and apparatus as the Dautriche method and the Mettegang recorder for the determination of the rate of burning of black blasting powder and other strictly burning explosives has been found to give such erratic results that no reliance can be placed on the data thus obtained. Consequently, investigators of those factors which may affect the burning rate, such as size of grain, absolute density, chemical composition, and means of ignition have had to rely mainly on observations made during practical use for determination of the part played by each. Such tests are very difficult of interpretation.The purpose of this paper is to describe a method used by the explosives division of the Bureau of Mines for the investigation of such explosives and to present the results of an investigation using that method.The investigation was concerned with the effect of grain size, initial pressure, and means of ignition on the rate of burning or rate of pressure development of black blasting powder as compared with pellet powder.The Bichel pressure gauge was used for these tests, with the slight modification to the apparatus and method described in U. S. Bureau of Mines Bulletin 15.4 These modifications consisted of reducing the speed of the revolving drum on which the time-pressure record is taken, measuring the speed of the drum by a belt-driven tachometer, and introducing an induction coil in series with the electric squib or electric detonator to mark on the time pressure record the instant at which the squib or detonator was fired."

May 1, 1929

By R. V. Ramani, R. A. Jankowski, R. Bhaskar

"The spatial distribution of airborne dusts, deposition of dust in the airway, as well as the effect of airflow velocity and particle density on dust behavior in mine airways were studied in a set of experiments performed in a mine airway under controlled conditions. Considerable deposition of dust near the source was indicated. Pronounced effects due to velocity were observed in ambient dust concentration and deposition along the mine airway, both in the respirable and the total size ranges. Cross-sectional concentration measurements indicate an increase in concentration from the roof to the floor. The average cross-sectional concentration is about 75% of the concentration in the center of the airway.IntroductionA number of studies have been performed since the early 1950s on the behavior of dust in mine air (Bradshaw and Godbert, 1954; Dawes and Slack, 1954; Bradshaw et al., 1954; Hall, 1955-56; Reinhardt, 1971; Ford, 1971; Courtney et al., 1982). While the experimental data available from these studies are indeed useful in understanding dust cloud behavior in a specific situation, no generalized conclusions can be drawn because of the lack of data on parameters such as flow velocity, size distribution of the source dust, and particle density. These change from mine to mine or even within the same mine. The present study is aimed at providing a better understanding of the temporal and spatial behavior of dust particles in underground' mine airways (National Academy of Sciences, 1980). The characteristics studied encompassed airborne concentrations and floor depositions over the entire size range as well as the respirable size range. The experimental results in this paper are intended to complement a mathematical model developed to predict ambient concentration and deposition of airborne dust in mine airways (Bhaskar and Ramani, 1986)."

Aug 31, 1989

By N. E. Hanna

Experience with the current version of gallery test 4, in use since 1913 to evaluate the incendivity of permissible explosives in the presence of coal dust, has shown the procedure to have inadequate discrimination. Consequently the Bureau of Mines used the up-and-down method of statistical design to investigate the incendivity of permissible explosives in the presence of coal dust and gas. A suitable device was developed to measure coal dust concentrations in the air-gas mixtures and to disperse the dust in the gallery atmosphere. A proposed testing method which uses suspended shots in a predispersed coal dust-gas-air mixture was evaluated. The new method can discriminate between different explosives with respect to their incendivity. Maximum ignitibility of the coal dust cloud by permissible explosives occurred in the vicinity of 0.3 oz/cu ft. About 10% sodium chloride in permissible explosive formulations had a very significant effect in reducing the probability of igniting coal dust. Bundled charges were more incendive than column charges.

Jan 1, 1966

In the United States water pollution resulting from mining activities has long been recognized as a major environmental problem Mine drainage pollution results from many types of mining activities and includes both physical (i e , sedimentation) and chemical (i e , acidification, metal contamination, etc ) pollutants Active and abandoned surface and underground mines, mineral processing plants, mine and processing plant waste disposal areas, haulage roads, and tailing ponds are typical sources of mine related water pollution (130) One of the most serious pollution problems arising from mining activities is acid mine drainage resulting from the chemical reaction of sulfide minerals (commonly iron sulfides) and air in the presence of water Acid mine drainage is commonly associated with coal and hard rock mining areas in the United States In general the more serious and extensive acid mine drainage problems exist in the more humid coal regions east of the Mississippi River (11) In 1964 the U S Department of the Interior, Fish and Wildlife Service, reported that acid mine drainage adversely affected fish and wildlife habitat in 9,477 kilometers (5,890 miles) of streams and 6,062 hectares (14,967 acres) of impoundments in 20 states in the United States (64) Of the total affected waters, coal mining operations accounted for 97 percent of the acid mine drainage pollution reported for streams and 93 percent of that reported for impoundments In 1970 more than 19,308 kilometers (12,000 miles) of streams in the United States were reportedly significantly degraded by mining related pollution (130) Of the total affected kilometers, 16,920 kilometers (10,516 miles) or approximately 88 percent were located in the Appalachian coal region (Pennsylvania, West Virginia, Ohio, eastern Kentucky, Tennessee, Maryland, and Alabama) In addition, more than 965 kilometers (600 miles) of streams reportedly were degraded by coal mining in states in the Illinois, Western Interior, and Rocky Mountain coal regions The remaining portion of the stream pollution resulted from the mining of (1) copper (california, Montana, Nevada, New Hampshire, Tennessee, Virginia, and Wyoming), (2) lead and zinc (Colorado, Idaho, Kansas, Missouri, Montana, Oklahoma, and Tennessee), (3) uranium (Rocky Mountain States), (4) iron (Lake Superior iron region), (5) sand and gravel (all states), (6) phosphate (Florida and other states), (7) gold (Alaska), (8) bauxite and barite (Arkansas), and (9) molybdenum, gold, and other metals (Colorado) Abandoned mines and abandoned mine waste disposal areas contribute a large portion of the total pollution resulting from mining activities Numerous abandoned underground mines are located throughout the United States and many are discharging mine drainage pollutants In 1966 the U S Bureau of Mines estimated that more than 88,000 inactive and abandoned underground mines were in existance (126) A listing of these mines by state is presented in Table 1 0-1 More recent estimates indicate that this list is incomplete In Colorado alone there is

Jan 1, 1975

By Arthur J. Hudson, Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion- proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures, a multicompartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 1992

By Richard V. Ageton

Compressed- air blowers are frequently used both in large and small metal ines , not only as an aid to ventilation , but in some mines as a substitute for an dequate ventilation system . As a temporary fixture , blowers have their uses , but hey should never be used in lieu of a permanent ventilation system. A number Probably the most common error made in placing dependence on compressed- air lowers as an aid to underground ventilation is the tendency to over- rate their cooling efficiency . It is a very common but natural error to assume that compressed air which issues freely from a blower is of the same temperature as the compressed air which issues freely from the exhaust port of a rock-drilling machine . of readings were taken in different mines of the temperature of the rock- drill exhaust , of the compressed air flowing from the blowers , and of the surrounding air In both cases . In general , the temperature of the rock- drill exhaust was from 10 to 30 degrees below that of the surrounding air , in many instances being slightly below freezing , 32° F . The average temperature for a number of compressed-air lowers and for the mine air surrounding them is shown in Table I.

Jan 1, 1922

By T. F. Dumm, O. Trass, V. R. Koka, L. G. Austin

"The size distributions of carefully screened 2 size fractions of ground materials were determined using a Microtrac laser dif-fractometer. The size distributions were fitted to the empirical function P(x) = 1/[1 + (x50/x)1] where P(x) is cumulative mass fraction less than Microtrac size, x. The standard deviation of A for a 50 second test time was approximately 0.5, so that seventeen test times give a mean with an estimated error within t 0.25 (95% confidence level). Values of were 5.44, 4.82, 4.40 for a coal ground under different conditions, indicating statistically different shape distributions; the average value for mica was 2.91 owing to the high aspect ratio of the particles. The ratio of x50 to the geometric mean sieve size was 1.2 for the coal and 0.70 for mica.1 IntroductionKoka and Trass have presented evidence [1,2] that materials ground in the Szego mill [3] give different shapes depending on the milling conditions. The variations in shape were deduced qualitatively by viewing SEM photomicrographs of selected 1/2 screen fractions. This paper quantifies their observed differences in shape by using measurements of the size distributions of screen fractions examined in a laser diffractometer [4] (Microtrac, Model 7991). The basic concept is that particles of 'a given ""screen"" size will give a wider distribution of ""Microtrac"" size when the particles are flaky with high aspect ratios, and a narrower distribution when the particles approach the cubical and spherical geometries.2 TheoryAustin and Shah [5] have shown that coal screened within a 1. 1/2 upper-to-lower sieve size range will give rise to a much wider distribution of Microtrac size. They found that the screen interval of irregular fragments of comminuted coals or quartz gave Microtrac size distributions which could be described by the simple function"

Jan 1, 1988

By A. Wahib Khair

"This article first describes the impact of respirable dust on the health of miners in underground coal mines in the United States of America. Second, it identifies the major sources of dust generation, namely cutting tools in the road headings. Two surveys associated with cutting tools were made to determine the useful life of these cutting tools, and to determine the effect of cutting tool wear on productivity of the continuous miners. Third, this article presents the results of a series of experiments carried out in the Rock Mechanics Laboratories at West Virginia University in order to study: 3.1 the effect of cutting tool rate of wear on respirable dust generation, 3.1.1 the effects of rock materials on tool wear and respirable dust generation, 3.1.2 the effect of cutting tool geometric parameters on respirable dust generation, and 3.1.3 the effect of tip materials used in the cutting tool on respirable dust generation. Recommendations in regard to cutting tool design are also presented in this paper.Silica and coal dust are the two major elements affecting the health of underground miners. According to Lemen [1] approximately 1,500 men died due to breathing in silica dust in 1936 while tunneling through a mountain of mostly silica, near the town of Gauley Bridge, West Virginia. Coal dust resulting in lung diseases in one of the major health hazards in underground coal mines. The impact of black lung on miners, coal workers' pneumoconioisis (CWP), has ranged from 16,000 to 23,000 each year since 1982 [1].The trend for conventional mining to continuous machine cutting of coal, using more productive machinery, is inexorable. Intolerable level of dust generated at the face is an indication of inefficient coal/rock cutting by these machines. The federal goverment of the United States paid about 11.7 billion dollars in workmen's compensation to more than 470,000 miners with CWP [2]. Bieniawski and Zipf [3] reported that annual benefit payments were about 2 billion dollars. The enactment of the Health and Safety Act in 1969 in the United States triggered the initial investigation into coal cutting mechanisms and cutting tool designs.The surveys concerning the utilization of cutting bits and performance of continuous miners in underground coal mines were made in order to have first hand information about bit consumption and coal produ¬ction.Three types of used bits, commonly utilized cutting tools on continuous miners, were collected from different coal mines. The used bits were grouped into symmetrically and asymmetrically worn bits. Distribution analysis for weight loss and conical height loss was done. Details of the results are presented elsewhere [4], here the results are summarized briefly. The analysis shows that approximately 50% of the collected bits have worn asymmetrically, which shows that many bits do not rotate properly during cutting. Analysis of the distribution of bit wear showed that the degree of bit wear varied from one type to another and with mining conditions. On average, the weight loss of the used bits was 4% to 7% with a maximum of 31%. Correspondingly, the loss of the conical height was observed to vary between 11% and 23% with a maximum of 71%. Figure 1 shows typical data associated with some of the used bits."

Jan 1, 1998

By Charles W. Huggins

Electron diffraction and electron microscopy were used to determine the unit cell parameters of garnierite [(Ni,Mg)3 Si2O5 (OH)4] and to examine its crystal habit. Bundles of ribbons, many less than 200 A. in cross section, make up the bulk specimen of the garnierite Electron diffraction revealed the unit cell to be monoclinic. Unit cell parameters were: a, 5.33 A,; b, 9.23 A.; c, 14.96 A.; and ß, 94°441.

Jan 1, 1961

By H. Kenworthy

The investigations described in this report were undertaken to demonstrate, on a laboratory scale, the possibility of recovering several million pounds of tin plus tungsten contained in stockpiled and currently rejected slags from the Longhorn tin smelter at Texas City, Tex. At the same time, it was anticipated that the treatment procedures developed might be applicable to slags from other tin-smelting operations. Results of the laboratory work show that it is possible, by pyrometallurgical means, to separate the tin and tungsten into products of intermediate grade that may be returned to the smelter circuits for further upgrading. Several methods of treatment were investigated. The methods that proved effective were: Fusion reduction, chloride volatilization, sulfide volatilization, and carbide formation. Over 90 percent of the tin and tungsten could be removed from the slat by any of these methods. Each type of treatment has advantages and disadvantages, and it could not be determined from the small-scale work which method was the more meritorious. Tungsten and (in some types of treatment) tin-bearing products were diluted by iron, the separation of which will require additional studies. Prevention of a portion of the iron from reporting with the tin or tungsten is a distinct advantage and possibility that will require inure laboratory work to develop the needed techniques for its accomplishment. Tin products from single treatments of stag ranged up to 75 percent in tin content but were more generally under 35 percent. Tungsten products were usually under 15 percent; but segregated portions could be selected, at a sacrifice in recovery, that contained up to 50 percent tungstic oxide equivalent.

Jan 1, 1957

By A. C. Johnson

This report is one of a series being prepared by the Bureau of Mines on exploration, development, mining methods, and costs at various mines in the United States. It describes operations at the Black Rock mine, Wah Chang Mining Corp., Mono County, Calif. The purpose of these reports is to promote development and conservation of our mineral resources by disseminating technologic information on mining methods, practices, and costs. The Black Rock tungsten mine of the Wah Chang Mining Corp. is 33 miles north of Bishop, Calif., in the Benton Range, Mono County, Calif. The property was acquired in August 1950 and a well-planned program of exploration, development, and exploitation resulted in a good production record with low costs. Operations were halted in July 1957, about 6 months after suspension of the tungsten purchase program by the Federal Government.

Jan 1, 1960

By J. C. Franklin

The Spokane Mining Research Center of the Federal Bureau of Mines is placing major emphasis on chemical stabilization as part of the ground support program. Development of polymeric material suitable for bonding rock fractures around the mine opening is one phase of the program. Some of the problems that must be considered are viscosity, applicability, adhesion, cure times, strength, toxicity, and flammability. Epoxies and polyesters were investigated, but shrinkage in polyesters caused redirected effort toward epoxies. Test results with the latter showed that bonded fractures in mine-roof strata were stronger than the virgin rock. Further tests showed that polymeric materials have good potential for bonding, and in conjunction with polymer roof bolts, are expected to result in an economic and useful new support concept.

Jan 1, 1974

By C. J. Johnson, C. J. Bise

"IntroductionCoal extraction by continuous miners (CM) is currently the most common underground method in the US industry and accounts for slightly more than two-thirds of the nation· s deep mining production (National Coal Association, 1987). Even if longwall mining should become more commonplace, it can proceed only af1er ventilation and access entries have been driven by CMs. Since an area of concern continues to be the effects of the dust generated on the health of mineworkers, this paper discusses the relationship between the elemental composition of mining-generated airborne dust sampled from the immediate ventilation return of a CM and laboratory-generated dust derived from channel samples taken from the mines.There are several potential contributions of this type of study to the coal mining industry. First after more fundamental knowledge of the causes of Coal Worker's Pneumoconiosis (CWP) is learned, the laboratory-generated respirable dust could be used to identify a potentially hazardous coal seam. Also, this study could possibly aid in understanding the fundamental causes of CWP by producing mining-simulated samples of coal dust that could be used in epidemiological studies.Further, assuming that there is no difference in the elemental composition of a drill-core sample and a channel sample from the same location a mining company could predict anew mine's respirable dust elemental composition In the immediate ventilation return by using exploratory drill core samples of the roof ,coal, and floor rock to prepare the laboratory dust. Ventilation engineers could then use engineering design and control measures during premine planning to reduce the incidence and severity of CWP by better ventilating the potentially hazardous coal seam. If this proper planning prevented any future changes to the ventilation equipment and mine design, much time and money could be saved.Scope of workTo investigate the variability of the chemical characteristics of respirable dust, airborne dust samples from eight underground coal mines located in the eastern and mid western United States were collected with eight-stage Sierra Model 298 Marple cascade impactors, as well as 25 channel samples of mined material. Each channel sample was removed from the middle of the coal face before mining occurred. Sampling of the mining-generated dust was conducted by Lee ( 1986) by sampling the entire working sections, primarily for characterization purposes, to obtain information on the locational variability of dust characteristics. Research performed for this study used the elemental analyses of the mining-generated dusts he sampled in the immediate ventilation returns of CMs."

Jan 1, 1989

By Miles B. Royer

The experimental blast furnace has attracted increasing interest during the past decade as a practical means for investigating a broad range of blast-furnace smelting problems. Under experimental-furnace conditions, information can be obtained with less expenditure of time and raw materials and, therefore, at lower cost than comparable information could be obtained under industrial operating conditions. Furthermore, the experimental furnace may be operated beyond the range of smooth operation, even to failure, to delineate the limits of operability. Such deviation from normal operating practice would be economically intolerable in industrial operations where production and operating stability might be disrupted. The Federal Bureau of Mines experimental blast furnace at Bruceton, Pa., near Pittsburgh, has been operated and under development since 1951. However, the usefulness of this experimental data to industrial practice was somewhat nebulous in early experiments, and the correlation of the experimental blast furnace with the industrial blast furnace was not known.

Jan 1, 1961