Search Documents

By Henry P. Wheeler

Natural gas was first stored underground in Welland, County, Ontario Province, Canada, in 1915.3/ The following year natural gas in the United States was first stored underground successfully in the Zoar field near Buffalo, N, Y. Only three additional storage fields were in use in the United States in 1930, but by 1940 the number had increased to over 30, and since that time growth has been more rapid. At least 80 fields, with a combined storage capacity of 440,828 MM c. f ., were being utilized by 1949.4 / In May 1952, 142 storage projects having a capacity of 915,000 MM c.f. were in operation .5/ These fields are distributed from New York to California--from Michigan to Texas. In the Appalachian region alone, there are 101 storage fields with a combined capacity exceeding 526,000 MM cu. ft. Why Natural Gas is Stored Natural gas is stored in order to be readily available to meet the needs of consumers.

Jan 1, 1952

By Earl W. Waay

"Since the beginning of the petroleum industry in 1839, up to within two or three years ago, these has been a dearch of engineers who have had the fundamental technical training also sufficient practical experience so that they could compete with practical men. Need for Technical Investigations in Industry: As in the early stages of the mining industry, the petroleum industry has been rather slow in realizing the need for technical assistance and investigators in the development and production of oil lands. The rapid increase in consumption, however, during the past few years has accentuated this need more than anything else could have done. When it is realized that our production cannot longer keep pace with the demand, it is easily understood why it is imperative that be instituted which will tend to conserve and prolong the supply of oil from the fields now known. It is interesting to note from preliminary production figure given cut by the U. S. Geological Survey, for the year 1919, that the United States produced about 430,000,000 barrels, an increase of 22,000,000 or 6 per cent over 1918 production and also there was imported, chiefly from Mexico, a little over 52,000,000 barrels, making a total of 430,000,000 barrels, to satisfy the trade demand in the United States of which almost 6,000,000 barrels was exported. Stocks were not materially increased.Other significant facts regarding our petroleum industry, are that just recently the U. S. Shipping Board in soliciting bids for 24,000,000 barrels of fad oil to meet prospective needs, received bids for only 1,500,000 barrels at prizes ranging from 75 to 90 per cent higher than was paid last year. One large company on the Pacific Coast has stopped its export trade, and has notified consumers,of gas-engine distillate that they will no longer make deliveries of this product. This will materially affect the farmer, in many instances, through his use of the truck and tractor."

Apr 1, 1920

By George C. Price

The Bureau of Mines conducted this study in the Roslyn No.5 coalbed in the State of Washington to determine the feasibility of mining hydraulically the portion of the coalbed that was steeply pitching. All of the experimental mining was done while advancing raises and rooms. A Bureau-developed hydraulic mining machine was used successfully in the pitching coalbed. It consisted of a remotely controlled monitor mounted on a self-advancing roof support unit of the type commonly used for roof support in longwall mining systems. The coal cutting rates averaged 0.73 and 0.54 ton per minute in raise and room mining, respectively, while using water volumes up to 230 gpm at a pressure of 4,000 psig. Productivity averaged 4.7 and 5.2 tons per man-shift for raise and room mining, respectively, compared with 7.5 and 8.5 tons per man-shift, respectively, by conventional hand mining methods.

Jan 1, 1965

By K. E. Stanfield

Asphalts from. Wyoming "black oils" are being studied at the Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming. These black oils are characterized by their high-asphalt, high-sulphur, and low-gasoline content and are difficult to refine by present methods into high-octane motor fuels, burning oils, and lubricants. Accordingly, their principal use, at present, is for the manufacture of road oil and asphalt. The present production of black oil could be increased to meet a greater demand. During 1937 the daily production of these crude oils in Wyoming was slightly over 13,000 barrels, while the estimated potential production from existing wells was 56,000 barrels.

Jan 1, 1939

By R. H. King

A very simple cold-bend test was devised and tested for evaluating thermoplastic jackets used on mine-power-feeder cables. A test sample is bent into a semi-circle whose radius is equal to the minimum bend radius recommended by IPCEA and then cooled to the, desired test temperature (-35°C). While at temperature, the sample is straightened by pulling the cable ends with a winch arrangement. The results show that of the jackets tested, those which cannot withstand the test literally burst when the sample is straightened.

Jan 1, 1978

By W. W. Simpson

The Bureau of Mines conducted research to determine the effects of potassium trithiocarbonate (KTTC), a degradation product of potassium ethylxanthate (KEX), on flotation of chalcopyrite and molybdenite. Small amounts of KTTC were identified in fresh and aged solutions of KEX using thin-layer chromotography. Hallimond tube flotation tests on pure minerals showed that KTTC acts as a weak collector for chalcopyrite. Both KEX and KTTC tend to depress molybdenite, but the depression effect is easily overcome by addition of a small quantity of fuel oil. The results of the Hallimond tube tests were confirmed in batch flotation tests using a porphyry copper ore.

Jan 1, 1983

By John E. Rourke, O&apos

A survey of existing and developing field permeability test methods was conducted in order to identify and specify capable methods to be used in feasibility investigations or performance monitoring for in situ leaching of ore deposits. Geologic settings of leachable deposits are discussed, as well as representative techniques used for the in situ leaching operation. Subsurface investigation techniques including drilling, core recovery, and down-hole inspection methods relevant to field permeability investigations are discussed. Field experience is examined and capable field permeability test methods are identified. Specifications for test borehole preparation, test performance. and methods of analysis are given. The test methods are comparatively rated in a matrix with respect to costs ease of use, and data effectiveness' for a broad range of conditions. Well Pump and Packer test methods receive high ratings. Recommendations are made for needed developments in field permeability test methods and a comprehensive bibliography is given.

Jan 1, 1977

By Ronald S. Conti

Historically, underground mine rescue teams have received training only in the course of actual emergencies, or in simulated mine environments, usually on the surface, with placards to identify objects and hazards. Also, while U.S. Federal Regulations require all underground miners to walk escapeways and conduct fire drills every 90 days, this does not fully prepare them for the conditions that may be encountered in real escape situations, such as smoke filled entries. This paper describes technology and realistic training simulations that have been identified for the general workforce and mine emergency responders. Of all the technology evaluated by underground personnel, laser lights and lifelines were most beneficial in leading personnel to safety and out of the mine in smoke-filled passageways. These technological advancements can improve the state of readiness for rescue personnel and increase the chances of survival for personnel escaping from underground emergencies.

Occupational illnesses are more difficult to identify than on-the-job injuries. Many illnesses related to occupational exposures may not be diagnosed until years after exposure; by that time, exposed workers may have changed jobs or left the workforce. Other approaches to identifying occupationally related illness are analysis of death certificate data (see chapter 2) and medical examination studies of workers known to have high exposures to hazardous agents. Figures 5-1, 5-3, 5-4, 5-6, 5-8, and 5-10 show, for each commodity, the percent of illness conditions reported to MSHA by nature of condition. Heart attacks that occurred on the job are reported without regard to work-relatedness. Figures 5-2, 5-5, 5-7, 5-9, and 5-11 show rates by year during 1986-1995 for selected conditions. Since there are many limitations on the accuracy of illness reporting, the frequencies and rates shown here should not be considered directly comparable across commodities. Figure 5-12 shows estimates for hearing loss by age among coal miners compared to a nonoccupationally noise-exposed population. These data come from a study by Franks [1996] of a group of audiograms obtained on coal miners by a commercial company. Using the NIOSH definition of hearing impairment, i.e., an average hearing threshold level for both ears that exceeds 25 dB at frequencies of 1,000, 2,000, 3,000 and 4,000 Hz, the figure shows that by age 30, more than 10% of miners suffer hearing impairment; by age 50, 90% of miners have hearing impairment. In contrast, only 10% of the nonoccupationally noise-exposed population suffer hearing impairment at age 51, and 50% of the nonoccupationally exposed population have hearing impairment at age 69. Figure 5-13 shows a similar analysis of commercial audiograms on male metal/nonmetal miners [Franks 1997]. At age 20, approximately 2% have hearing impairment using the NIOSH definition of hearing impairment described above. This increases to 7% at age 30, 25% at age 40, and 49% at age 50. In contrast, only 9% of the nonoccupationally noise-exposed comparison population have hearing impairment at age 50. Franks' analysis showed a different pattern for female metal/nonmetal miners; they developed hearing loss at the same rate as would be expected for a non-noise-exposed female population.

Jan 5, 2000

By F. W. Hoertel

The Bureau of Mines investigated the use of depleted uranium as a sacrificial anode for the cathodic protection of submerged and underground structures of iron , steel , and copper . Uranium-metal couples were tested in simulated marine environments of varying oxygen contents at pH values between 5.5 and 8.5 and under simulated boiler service condition in Rolla , Mo. , city water . Similar couples were tested in samples of Missouri soils to simulate underground service . Uranium remained anodic to iron , steel , and copper in the simulated marine environments and under simulated boiler service if the electrolyte was oxygen- free city water . Uranium appeared to offer limited protection to iron , low- carbon steel , stainless steel , copper , and zinc in the simulated underground tests . Uranium anodes offer a space advantage because 1 cubic inch of uranium gives approximately the same protection as 2 cubic inches of magnesium or 1-1 /2 cubic inches of zinc .

Jan 1, 1963

By K. E. Stanfield

Asphalts from. Wyoming "black oils" are being studied at the Petroleum Experiment Station of the Bureau of Mines at Laramie, Wyo., in cooperation with the University of Wyoming. These black oils are characterized by their high-asphalt, high-sulphur, and low-gasoline content and are difficult to refine by present methods into high-octane motor fuels, burning oils, and lubricants. Accordingly, their principal use, at present, is for the manufacture of road oil and asphalt. The present production of black oil could be increased to meet a greater demand. During 1937 the daily production of these crude oils in Wyoming was slightly over 13,000 barrels, while, the estimated potential production from existing wells was 56,000 barrels.

Jan 1, 1939

By G. R. Hopkins

"The average heat requirement per barrel of crude refined in the United States rose from 579,000 B. t. u. in 1940 to 584,000 B. t. u. in 1941. This marked the second successive year in which there was an apparent loss in fuel efficiency at refineries. This ""loss"" took place despite an increase in crude runs, which used to be an invariable indicator of a lower average.Probably the chief factor in the increased heat requirement in 1941 was the gain in the over-all gasoline yield from 43.1 percent in 1940 to 44.2 percent in 1941. Possibly another important factor was the further use of obsolete equipment to increase throughput.The refiners used more of all kinds of fuel excapt coke in 1941 than in 1940. However, the only fuels which increased materially in relative importance were refinery gas, which contributed 51.6 percent of the total heat units in 1941 compared with 50.7 percent in 1940, and natural gas, the share of which rose from 17.1 percent in 1940 to 18.0 percent in 1941. The changes in the percentages for the other fuels were as follows: Oil decreased from 25.7 to 24.1 percent; acid sludge fell from 2.7 to 2.5; coal remained at 3.4 percent; and coke (including steam) fell from 0.5 to 0.4 percent.New records for fuel efficiency were set in all three of the districts east of the Mississippi, namely, East Coast, Appalachian, and Indiana, Illi¬nois, etc. All the ether districts reported higher average fuel requirements in 1941, except the Louisiana Gulf and Arkansas-Louisiana inland.Since the year of the first statistics, the refiners have steadily increased their purchases of electricity. In 1941 total purchases were 1,862,996,000 kilowatt-hours, or 11 percent more than in 1940."

Apr 1, 1943

By Timothy M. Barton

The U.S. Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. A particular concern is ground control for deep-cover 1ongwalls located at depths in excess of 1,000 ft. The study described in this report was performed in two experimental sections in one longwall headgate section which contained three different pillar designs. Two of the designs used conventional abutment pillars, while the third was a total-yielding pillar system. Both of the test areas were located under 1,800 ft of cover. The purpose of this study was to evaluate the effectiveness of these three pillar designs for gate road stability. As the longwall mined passed the test areas, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The study indicated that the all-yield system performed nearly as well as the better of the two abutment pillar systems; but all of the three designs would have failed to provide acceptable stability for second panel mining without considerable artificial support.

Jan 1, 1989

By Alan R. Buehler

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 256,430-acre Alvord Desert and part of the 22,240-acre East Alvord Wilderness Study Area (OR-002-074 and OR-002-073A, respectively), in order to evaluate their identified mineral resources. The study areas are located in Harney and Malheur Counties, OR, about 25 mi northeast of the small village of Fields. There are no mines, prospects, or identified mineral resources inside the study areas. Basalt flows within the study areas contain chalcedony-lined vugs and banded agate which may be of interest to rock hounds. An ignimbrite flow contains perlitic material, but crystalline contaminants make it unsuitable for commercial uses. Lacustrine (lake) sediments contain diatomite and clays, and evaporite crusts contain boron too low grade to profitably mine. Small quantities of common opal and petrified wood occur which might be of possible interest to rock hounds. Some of the petrified wood is black, free of fractures, and polishes well; it may be suitable as backing material for soft, thin, and brittle gemstones, such as precious opal. The lacustrine sediments also contain black, fetid layers which have above background, but economically insignificant concentrations of zinc, cobalt, nickel, barium, iron, manganese, aluminum, and potassium. Large quantities of fine-grained dune sands within the study areas are too far from markets for economic consideration. Ephemeral streams in the study areas contain small amounts of placer gold of no economic interest. The western portions of both study areas are reported to have moderate favorability for occurrences of natural gas, and both study areas are reported to have high favorability for the occurrence of geothermal resources. As of December 1986, oil and gas leases covered 3,100 acres in the study areas.

Jan 1, 1987

Case studies from four western states are used to illustrate the impact of the environmental compliance process on the mining industry. The case studies were not chosen as a statistically significant sample of all mining operations in the western United States but were chosen as representative of operations on both public and private lands and in locations that exhibited varying degrees of involvement by governmental units, non-governmental organizations and the general public. Basically, each case study was chosen because some aspect of their environmental compliance process helped to illustrate an interesting point in the regulatory process. The criteria used to select the case studies were: mines located in different jurisdictional areas, mines located in varying geological areas~ mines located in areas having different historical relationships with mining: and operations that are in production as well as those seeking an operating permit. The variety of such projects should provide the necessary foundation to evaluate the impacts of the environmental compliance process in each location.

Jan 1, 1994

By L. B. Berger

This information circular is a revision of I.C. 7238, Danger from Carbon Monoxide in the Home, by L. B. Berger and H. H. Schrenk, issued in April 1943. Each winter brings its toll of deaths and serious accidents from the deadly gas, carbon monoxide. Newspapers carry warnings to the public of the, dangers of this gas, and frequent news items report the finding of persons dead at unconscious from the effects of carbon monoxide, yet these accidents continue. Either these warnings are not read, or they are unheeded by people who feel that, "It can't happen to me." It can happen to you carbon monoxide is no respecter of persons.

Jan 1, 1954

By J. C. LaScola

Development of methanometers and anemometers for underground use in coal mines is reviewed. The first semicontinuous recording methanometer was developed in 1961 in West Germany. The Bureau of Mines developed an instrument using; pellesters that was a continuous recording methanometer. Expansion of freon gas created a vacuum which pulled the methane-air mixture through a tube to an electrically heated, catalyst-impregnated pellester where the mixture was burned. The National Coal Board of England developed a continuous recording methanometer based on the principle of the Davy flame safety lamp. A thermo-pile was used to sense the hurt output of the flame. Finally the Bureau of Mines improved its methanometer by eliminating the freon gas and using a diffuser head to a monitor methane-air mixtures. Development of recording anemometers proceeded from the use of a photo¬cell and light source to sense rotation of the Biram-type anemometer blades to the use of a Hall detector to sense, rotation by measurement of electromagnetic pulses.

Jan 1, 1969

By K. C. Dean

During the investigation of the occurrence of manganese deposits in western United States, the Bureau of Mines collected 2-ton samples from three oxide manganese ores in the Columbia and Elberta Mining Districts, Tooelo and Juab Counties, Utah. To determine the amenability of these ores to standard ore-dressing methods: of concentration, extensive laboratory tests were made. The Wildcat property, one of those sampled, is 7 miles east of Fairfield, Tooele County, Utah. The ore is described as a replacement deposit and occurs along fracture and bedding planes of shale and limestone. Experimental work was done on a sample taken from a stockpile at the mouth of the shaft. The Wildcat manganese ore is intermediate in grade (25.7 percent manganese) and contains clay as the principal gangue constituent. A high-grade product was obtained with high recovery of Manganese by simple washing.

Jan 1, 1949

By A. B. Hooker, Iilsley. L. C.

"Flame safety lamps have been used for about one hundred years in coal mines where a dangerous accumulation of explosive mine gas (methane) might occur and thus render the use of ordinary unprotected flame lamps dangerous. Flame safety lamps are not only used for illumination, but also for detecting the presence of dangerous percentages of methane mixed in the air of the mine.The safety of the lamp depends chiefly upon the cooling qualities ofThe safety of the lamp depends chiefly upon the cooling qualities of the wire gauze used to permit free circulation of the air through the lamp. If one enters a part of the mine where methane is present in the air, the methane enters the lamp and coming in contact with the wick flame is ignited and continues to burn within the gauze without igniting the methane surrounding the lamp. If the air within the mine is traveling at a velocity of several hundred feet per minute the burning gases may be driven through the gauze by the air current. If the gauzes are properly designed and of the proper material, these burning gases will be so cooled as they pass through the gauze that they will not cause an ignition of the gas surrounding the lamp. In order to test the effectiveness of a given safety lamp, tests are made in moving explosive mixtures of gas and air arranged to simulate mine conditions.The Bureau of Mines investigated many features relative to the safety of flame lamps and in 1915 established an official schedule known as Schedule 7 whereby flame lamps having certain prescribed qualifications would be approved as permissible for use in gaseous mines."

May 1, 1920

By Brian L. Quick

Problem: The National Institute for Occupational Safety and Health's [NIOSH] National Occupational Research Agenda (DHHS Publication No. 96 115) reports that approximately 50% of miners will experience hearing loss by age 50, compared to only 9% of the general population. The present investigation examines three antecedents believed to be associated with miner's use of hearing protection. Method: A posttest delayed posttest control group field research design was employed to assess antecedents toward wearing hearing protection. Results: Following the initial posttest, miners' attitudes and subjective norms were antecedents to intentions to wear hearing protection devices. Also, intentions toward wearing hearing protection predicted hearing protection behaviors. Approximately six weeks later, miners' attitudes and perceived behavioral control were each significant predictors of intentions to wear hearing protection and again, intentions were positively associated with hearing protection behaviors. Impact on Industry: Our results indicate that appeals to normative influences may be the most effective antecedent to employ when persuading coal miners to wear hearing protection. However, messages designed to impact attitudes and perceived behavioral control were also effective.

Jan 1, 2008