Search Documents

Treat contaminated coal mine drainage to meet EPA and State water quality requirements. Approach A model (fig. 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of abandoned mine lands (AML). The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions.

Jan 1, 1992

By Harry D. Jumper

This paper describing the methods of ruining a sand, gravel, and bowlder deposit 20 miles east of Los Angeles, and the classification and preparation of these materials for market, is one of a series being prepared for and published by the United States Bureau of Mines on methods and cost of mining sand and gravel. These papers are designed to disseminate technical information regarding, the methods used. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion anti study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations stall ensue. The description contained herein is typical of this industry in Southern California. ACKNOWLEDGMENT The author acknowledges tine assistance of L. L. Rogers, vice-president and manager of production and distribution for the Consolidated Rock Products Co., in the preparation of this paper.

Jan 1, 1933

By Allan M. Johnson

Case histories were used to document and evaluate deficiencies in underground mine closures which have resulted in post-operation problems such as subsidence shaft failures, acid or toxic water drainage and others. Three different underground mining districts in the United States were investigated; 1) an iron mining district in Michigan 2) coal mining districts in eastern Ohio and southern Illinois and 3) three metal mining districts in central Colorado. Previous work in the Michigan district on problems with subsidence and acid water drainage provided the background from which the concept for this project was developed Student investigators working towards their MS degrees in Mining Engineering did the work on the eastern coal and western metal districts. The combined studies show that problems from acid water drainage, subsidence and inadequately protected mine shafts are the most severe and widespread. Suggestions of a technical nature are presented as partial solutions to some of these problems. It was determined that pre-closure evaluations could result in the identification of some potential problems that may occur after the mine is closed. Early recognition of these problems would be an advantage for at this time more options are available to the mine operator to either prevent them or to plan for their occurrence. Mine closure and reclamation should be considered as a part of mining and be incorporated in the mining plan. This would result in reduced environmental impact and would be achieved at a lower overall cost to the mining companies and to society. The role of water in the occurrence of several types of subsidence during mine flooding was significant at some mines in the Michigan district. These mechanisms which involve, friction reduction, gravity loading, overburden transport and hydraulic forces in a flooded mine probably have a broader effect than is currently recognized. Control of these processes may offer some interesting options during mine closure. It is recognized that technical solutions alone cannot provide all of the answers to problems associated with underground mines. Education, modified attitudes on the part of regulators and operators, and a more realistic perception of the importance and value of mining by the general public are also needed.

Jan 1, 1983

By Jan M. Mutmansky

"When, in 1973, a limit was placed on the amount of dust in the coal mine atmosphere, restricting the average exposure of a coal miner to 2 milligrams of dust per cubic meter of air (mg/m'), skeptics in the United States and abroad Said the standard could never be achieved. They cited much more lenient standards already established in other countries and refused to believe that the United States could meet the world's most stringent requirements in mines where dust had never before been regulated. Yet 10 years later the goal had largely been achieved and miners were working underground in a cleaner atmosphere than ever before. It was a major achievement and a big stride in what had become a war on coal workers' pneumoconiosis (CWP), the black lung disease prevalent among miners in underground coal mines.Although the health hazards caused by working in a dust-filled mine atmosphere have long been recognized, the problem became particularly acute in this century with the mechanization and increased productivity of underground coal mining. The United States was much slower than some other countries to address the problem of respirable diseases among miners. While dust levels in South African gold mines were first regulated in 1912, in the United States it was only when 476 workers died of silicosis while blasting a tunnel through a mountain near Gauley Bridge, West Virginia in the 1930s that widespread public attention became focused on the plight of workers in dust-filled environments. Another 30 years passed before regulation of dust finally became law in the Coal Mine Health and Safety Act of 1969.With a stringent new standard imposed in all underground coal mines, the industry was faced With the daunting problem of reducing levels of airborne dust from perhaps 6.5 mg/m' to 2 mg/m', in an inherently dusty operation carried out in the close confines of underground passageways. Most of the coal dust is made by the cutting operation in which the continuous miner or longwall machine can produce several thousand milligrams of respirable dust for each ton of coal mined. Other dusty operations such as drilling holes for roofbolts, loading and unloading coal on shuttle cars, and the operation of conveyor belts contribute to the overall problem.Since the institution of the new dust control standards, a number of strategies have been adopted for reducing the coal dust in the mine atmosphere. These strategies involve engineering and design improvements that help lo prevent the generation of particles, keep particles of dust from becoming airborne, carry dust away from the working area, and isolate the dust from the workers in the mining operation. These procedures have been pursued vigorously by the Bureau of Mines, and many successful methods have been developed to reduce the mass concentration to which the workers are subjected. The mining companies were reluctant at first to confront the problems but after a period of trials and gradual improvement, they joined with others in the fight to reduce the dust concentrations in the working place."

Jan 1, 1990

By M. J. Sapko

The Bureau of Mines conducted laboratory-scale flammability experiments to investigate the possible use of water spray systems for inerting or quenching mine-gas ignitions, such as those encountered at the working face of a coal mine. The inerting results for premixed methane-air-water mixtures indicated that water droplets of less than 10 µm tend to be as effective as the vapor. Water requirements for inerting such mixtures were much smaller than those for quenching the sustained flame propagation by the application of water sprays. The minimum water mass concentration for quenching methane-air flames increased linearly with increasing droplet diameter (surface weighted mean) and decreased with increasing spray temperature, whereas the droplet surface area required per unit volume was essentially constant for a given gas mixture composition. Data extrapolations indicated that a quenching system may be feasible for the longwall mining application.

Jan 1, 1977

By William C. Larson

This Bureau of Mines report discusses uranium in situ leach mining in the United States to acquaint the public with an overview of this emerging mining technology. This report is not intended to be a technical discussion of the subject matter, but rather should be used as a reference source for information on in situ leaching. A list of in situ leaching publications is included as well as engineering data tables for almost all of the active pilot-scale and commercial uranium in situ leaching operators. These tables represent a first attempt at consolidating operational data in one source, on a regional basis. Additional information is given that discusses the current Bureau of Mines uranium in situ leaching research program. Also included is a listing of various State and Federal permitting agencies, and a summary of the current uranium in situ leaching operators. Finally, a glossary of terms has been added, listing some of the more common terms used in uranium in situ leach mining.

Jan 1, 1978

By August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 2010

By D. J. Parker

Owing to its flexibility, convenience, economy, ands availability, electric power is peculiarly adapted to the needs of the coal -mining industry. Because of such obvious advantages, the application of electricity has in recent years become more and more extensive and is now a most important factor in the Nation's coal prediction. With the introduction of this type of power into coal mines certain new, specific, and well-recognized hazards resulted. The question arises, therefore: Has the industry met these hazards squarely and. effectively? With respect to some individual companies, the answer happily is in the affirmative; with respect to the industry as a whole, there is much room for improvement.

Jan 1, 1933

By E. J. Gleim

A list of permissible mine equipment, tested and approved previous to January 1, 1942, was published In Bureau of Mines Information Circular 7207.3/ The present list covers additional equipment approved during the calendar year 1942. The items have been numbered to indicate the order in which each type of machine or device was approved in its particular classification. Thus, Information Circular 7207 gives four air compressors on the Bureau's active list, and the present circular gives the fifth to be approved. Items 90 and 94 under Loading; Machines land Conveyors also appear in Information Circular 7207. These numbers are repeated hero to show that approval was granted during 1942 for additional voltages on machines previously listed one voltage only. Equipment listed in these circulars is approved by the Bureau of Mines only when found upon inspection and test to comply with minimum standards of safety as outlined in schedules prepared on the basis of many years of experience in dealing with safety problems of the coal-mining industry. The use of such equipment in mines known to be gassy, as well as in those which may become so, is earnestly recommended in the interests of safety. This circular is published so that the industry may be kept informed as to the many types of machines, devices, and lamps that arc available for reducing explosion and other hazards incidental to coal mining. The present paper and Information Circular 7207 together give the complete list of all available permissible .Mine equipment.

Jan 1, 1943

By H. H. Schrenk

There are several well-recognized procedures for controlling exposure to hazardous atmospheres in industry. They include (a) substitution of less toxic material, (b) enclosure of processes, (c) wet methods, (d) local exhaust, (e) general ventilation, and (f) use of respiratory protective devices. In addition to their employment as a control measure in occupational exposures, respiratory protective devices also are essential in emergencies that may arise from failure or improper use of other control equipment. Respiratory protective devices usually are employed to supplement other methods of control, as temporary expedients, or when other methods are not readily applicable or practicable. It seems reasonable to assume, however, that where respirators are used consideration has been given to the factors involved and that the devices can provide satisfactory protection if used properly. Their use should not be arrived at simply by a process of elimination of other methods that are more difficult to apply.

Jan 1, 1943

By R. L. Hopkins

The work described was performed to determine whether sulfur compounds of the thienothiophene class occur in crude oil. The presence or absence of various classes of sulfur compounds in crude oils is of interest and value to petroleum science. The Bureau of Mines, for the first time, identified hydro-carbon products of desulfurization that point directly to the identity of two individual thienothiophenes, namely 3-methylthieno[2,3-b]thiophene and 2-meth-ylthieno[3,2-b]thiophene, in Wasson, Texas, crude oil. These identifications, described in detail, were accomplished using microdesulfurization, mass spectrometry, and gas-liquid chromatography.

Jan 1, 1966

By Earl R. McMillan

"Coal washing commands the thoughtful attention of a steadily incre in number of people. Clean coal is not merely a luxury but is rapidly becoming a necessity in some industrial operations.Coal seams in the Northeast are rarely free from ""bone"" and shale or clay partings which vary from a fraction of an inch to several feet in thickness. Nearly all of the coal measures are folded and faulted, the coal seams dip at various angles, and in some cases are badly broken. In mining these seams fragments of the roof and floor, as well as partings of impur-ities within the seams, unavoidably become mixed with the coal, so that the raw coal as it comes to the surface often contains as much as 50 per cent, by weight of waste.At the Bureau of Mines experiment station at Seattle, the washing of this coal in order to improve it for commercial use has been studied. Since the process of coal-washing depends upon differences in specific gravity between the clean coal and, its associated impurities, the first problem undertaken was that of determining the specific gravity of the clean coal and of each parting of impurity contained in a large number of representative seams.It was found that the freshly-mined coal is practically saturated with water, this being observed in determining the effect of moisture content upon the specific gravity of the coal particles, selected from samples of coal varying from low-grade subbituminous up to semianthracite, all of which are found in the State of Washington. The specific gravity values determined for the cleanest particles varied from 1.28 to 1.35; in general, the higher the rank of the coal the hither the specific gravity."

Nov 1, 1920

By George S. Rice, J. W. Paul, E. H. Denny

Data assembled by the Bureau of Mines , coupled with requests from coal companies , have emphasized the desirability of establishing standardized specifications for brattice cloth with particular respect to durability and fireproofing . Brattice cloth is a canvas or other material , often covered with some fireproofing composition , which is used extensively in coal mining for temporarily deflecting air into pillar workings and maintaining ventilation at the working faces . These specifications will be established , it is planned , through a cooperative program in which the U. S. Bureau of Standards will make a series of tests of various brattice cloths treated with respect to fire- resisting qualities and the U. S. Bureau of Mines will continue to assemble field data on the use of brattice cloth . Plans now are being made for this cooperative work. Without attempting to make a complete survey , the Bureau of Mines has made preliminary studies and investigations , and verious representative coal - mining companies have furnished detailed information . The information thus gained will be used as the basis for the cooperative investigation , but the Bureau of Mines would welcome additional information from mine operators on the character and weight of brattice cloth , conditions of use , durability , quantity employed and price . Such information should be sent to the Director , Bureau of Mines , Washington , D. C. The mine operator is interested in procuring at reasonable cost a brattice cloth with lasting fireproofing quality and of as great durability and strength as possible . There has been a lack of assembled data and knowledge regarding the subject , but the Bureau of Mines feels that this lack of knowledge may be overcome if the coal -mining companies will lend their hearty support to the cooperative investigation and submit information relative to the use of brattice cloth in their own properties . Information contained in this report is based on data obtained from coal operators in bituminous districts of Pennsylvania , Alabama , Utah , Indiana , Illinois , Colorado and Nova Scotia .

Feb 1, 1923

By V. Castranova, K. Van Dyke

"I. INTRODUCTIONA mechanism which is present in leukocytes and capable of releasing histamine from rabbit platelets was first described by Barbaro and Zvaitler in I966. A soluble mediator between rabbit leukocytes and platelets was also detected by Siraganian and Osier in 1971. This factor was isolated and characterized in 1971 by Benveniste et al. and named platelet activating factor i PAF). It was shown to be released from rabbit basophils through an antigen - IgE-dependent mechanism. The presence of PAF in human leukocytes' and its aggregation and releasing effects on human platelets were also demonstrated. Chemical analysis has shown that PAF is a glycerophospholipid with a choline polar head group. an ester-linked acyl chain at the second carbon and a nonester link at the first carbon.' The structure of the mediator was found to be 1-O-alky1-2-acetyl-sn-glyceryl-3-phosphoryl choline and it has been chemically synthesized.""' A variable portion exists in the alkyl group attached to the first carbon which can have a variety of molecular sizes such as C and C (where Cu is more abundant). Recent work by Pinckard et al."" has shown that there are at least five variations of the alkyl group.PAF has been shown to have a broad range of biological effects. Release of PAF from alveolar macrophages may be important in asthma, allergy, and shock states. In a rabbit model of antigen IgE anaphylaxsis. PAF can induce all of the effects of antigen challenge and. therefore is presumed to be a key mediator in production of anaphylaxsis. In addition to aggregating and degranulating platelets it is a potent chemoattractant."" and causes contraction of guinea pig ileum contraction of lung tissue and enhanced capillary permeability PAF has important effects in the kidney and is also known as the renal hypotensive factor proposed by Blank et al. who found the structure of PAF independently of Benveniste et al.' In producing these responses. PAF acts by a receptor-like mechanism. In platelets. PAF selectively desensitizes itself but not thrombin or collagen. In smooth muscle tissues a similar phenomenon occurs with anaphylatoxin or other stimuli.In vivo. PAF probably acts in concert with other agents in producing its various biological effects. It causes platelets to release histamine serotonin and RCS (rabbit-contractile substance formed from prostaglandins PPG2, PGH2 and TXA2) which contracts rabbit aorta. PAF can cause cells to release SRS-A and leukotriene B."

Jan 1, 1989

By E. H. Denny

"IntroductionOn May 27, 1927, a coal-dust explosion occurred at the Palagua No. 5 mine of the Victor American Fuel Company, Delagua, Colorado, resulting in the loss of even lives and in and in considerable damage to the main slope and to several overcasts the explosion did not extend into the mine working where 125 additional men were employed but escaped uninjured. It is believed that the saving of these 125 men and the evidence of large property loss were due in a large measure to coal-dusting and of other sanity measures taken by the coal company management. A number of features connected with the explosion and mine safety practice seem worth the attention of the mining public and grateful acknowledgment is made to the Victor American Fuel Company for its aid in assembling the data herein contained."

Nov 1, 1927

By L. H. Kalenowski

The metal lithium, its alloys, and its salts are becoming Increasingly important as industrial materials. Lithium metal, because of its great affinity for elements, such as nitrogen, hydrogen, oxygen, sulfur, phosphorus, carbon, and silicon, has become important for a wide variety of uses, ranging from purifying helium gas by removing the nitrogen to scavenging molten metals of undesirable impurities. The excellent fluxing properties of lithium salts have found increasing use in such applications as fluxes for welding aluminum and in lower melting ceramic glazes and coatings. Lithium chloride is one of the most hygroscopic salts known and is widely used as a dehumidifying agent. .About 17 lithium minerals are known. Four of these have commercial importance: Amblygonite, lepidolite, zinnwaldite, and spodumene. Spodumene is the most important source of lithium and lithium salts at present, but sizable deposits of amblygonite occur in the pegmatite area of the Black Hills of South Dakota. The size and nature of these deposits preclude the, possibility of, any assurance of an adequate supply of amblygonite for an operation processing only this mineral. Frequently spodumene and amblygonite occur associated in pegmatite minerals. Preliminary investigations indicate that a simultaneous recovery of spodumene and amblygonite can be made by froth flotation. A single process for treating spodumene and amblygonite or mixtures of thorn, would make possible more use of amblygonite as a source of lithium and obviate the separation of spodumene and amblygonite when they occur together.

Jan 1, 1952

By Steven J. Page, John A. Organiscak

Prolonged exposure to airborne respirable coal mine dust is responsible for coal workers' pneumoconi¬osis (CWP): Furthermore, miners who show evidence of higher radiographic categories of simple CWP are at increased risk of developing progressive massive fibro¬sis (PMF). As of 1990, there were nearly 130,000 coal miners in the United States. "' This excludes mines that produce less than 10,000 tons annually and the anthracite coal mines. Estimates indicate that at age 58, an average of 7/1000 U.S. workers and 89/1000 U.K workers will have developed PMF(2-1) Health research studies have iden¬tified that the risk of developing and the severity of CWP arc directly related to (1) the amount of respirable dust exposure and (2) the coal rank.,'- The rank of coal is its stage of formation in the series peat, lignite, sub-bituminous, bituminous, and anthra¬cite (in order of increasing rank). The rank of coal can also be represented by the com¬mercially important characteristics specified by its proximate analysis: fixed carbon, vol¬atile matter, mineral matter, and moisture content.

By John H. Soule

"Although known since 1902, the Capitan iron deposits have not been mined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-45, visited the property; as a result, preliminary sampling of the property was done in 1943.3/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944.4/ Equipment available at that time was limited in the depths that could be reached; and, as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.The following sections note the location and accessibility of the deposits and mention the physical features, climate, labor and living conditions. Property and ownership are outlined, the history and production of the property stated briefly, and the ore deposits are described. The work done by the Bureau of Mines is explained and supported with maps, sections, and assay logs.From March 1, 1944, to June 1, 1944, 179 wagon-drill holes totaling 3,490 feet and 4 test pits totaling 75 feet were completed, and from November 1947 to February 1948 seven churn-drill holes totaling 2,488 feet were drilled and sampled. Metallurgical tests are summarized and referenced.With respect to this report, special acknowledgment is due to J. H. Hedges, chief, Tuscon, Ariz., Branch, Mining Division, and to W. R. Storms, engineer in-charge of the Silver City, N. Mex., field office. Acknowledgment also is due to J. Bruce Clemmer, chief, Tuscon Branch, Metallurgical Division, for analyses done in the last phase of this project, and to Dr. Vincent Kelley of the Federal Geological Survey for his cooperation during this work.The Capitan iron deposits are in secs. 10, 11, 13, 14, and 15, T. 8 S., R. 14 E., central Lincoln County, N. Mex., as shown on figures 1 and 2. The only known large deposit upon which the Bureau did development work lies around the common corner of secs. 10, 11, 14, and 15, as shown in figures 2 and 3, and just southwest of and in the foothills of the Capitan Mountains. This range of mountains trends east and west. The elevation of the highest peak is 10,205 feet.The deposits are reached by traveling on State Highway 48 from Capitan north for 4 miles, to a point just inside the Lincoln National Forest fence and thence due east over a poor dirt road for 1.2 miles. Just over a small wooden bridge, the left-fork is taken, and the poor road is followed to the deposits, a further distance of 1.1 miles (see fig. 1). This road follows the fence to and through the Davis ranch. All the roads from Capitan to the deposits are dirt roads but are impassable only for short periods during and after heavy rain or snow."

Aug 1, 1949

By F. N. Kissell, C. H. Elder, C. M. McCulloch

The applicability of the "direct method" for determining the methane content of virgin coalbeds was tested. Preliminary results indicate that the direct method, when applied to exploration cores, can be successfully used to estimate coalbed gas content and also approximately predict the total gas emission from a prospective mine located in the coalbed at the exploration site.

Jan 1, 1973

By John C. Machisak

Statistical data on injuries in the metal and nonmetal industry of the United States first became available to the Bureau of Mines by collecting reports from the operators for the calendar year 1911. Since then reports have been collected annually. The present bulletin, covering the calendar year 1954, is the 31st publication (1933-34 was published as Bulletin 398) containing statistical data on injuries at metal and nonmetal mines and related plants, and it 1s the first such bulletin to be published since 1942. The last publication was Bulletin 461, Metal and Nonmetal-Mine Accidents in the United States, 1942. The unpublished statistics for 1943-53 may be found in the Appendix of this bulletin. The Bureau of Mines is authorized to collect data on injuries and related employment at metal and nonmetal mines, but there is no Federal law that compels operators to submit such information. Therefore, all materials submitted are voluntary responses to the Bureau's requests for information. The figures presented herein may not be complete for the entire industry, nevertheless, every effort has been made to make them so, and the data given are believed to be representative of the hazards to which metal and nonmetal workers are exposed. Moreover, the figures are comparable as between States-which is significant in view of the lack of uniformity among the States as regards classes of plants covered by State laws, classes of injuries covered by State reports, and other factors that tend to make it impracticable or impossible to compare the injury experience of one State with that of another or comprehend the relative importance of the various causes of injuries in the industry as a whole.

Jan 1, 1957