Search Documents

By W. H. Frederic, A. C. Fieldner, W. A. Selvig

"Low-rank coals have a pronounced tendency to disintegrate or ""slack” when alternately dried, and wetted by exposure to the weather. The more readily a coal slacks the greater is its tendency to ignite spontaneously and the more care must be used in its shipment and storage. Lignite slacks very readily when exposed to the weather. Slacking trouble is also experienced in shipping and storing subbituminous coal, but not to the same extent as with lignite. As a rule, bituminous coals are only slightly affected by weathering and in general may be classified as nonslacking coals. The slacking tendency of subbituminous coal is one of the characteristics that is used to distinguish it from bituminous coal. An accelerated laboratory method of test was developed to measure such slacking tendencies. This method was applied to a number of coals, principally from the State of Washington, and the method and the results obtained are given herein.Helpful information concerning slacking tendencies of coal was received from Marius R. Campbell, senior geologist U. S. Geological Survey.Coals that slack readily contain relatively large amounts of moisture. When exposed to the weather such coals lore moisture rapidly. As the coal loses moisture at the surface there is a gradual drift of moisture from the interior of the piece to the surface. If the loss of moisture at the surface proceeds at a faster rate than it is replaced by moisture from the interior of the coal piece, there undoubtedly in greater shrinkage of the coal at the surface as tom-pared to the interior of the piece and stressed are generated in the surface coal.These stresses in the surface coal cause it to crack and disintegrate.Likewise, when the air-dried coal is wetted by rain, the exposed surface of the coal pieces gain moisture more rapidly than the interior of the piece, causing greater expansion in the surface coal and the coal breaks down further. As this process of air drying and wetting is continued when the coal is exposed to the weather, the slacking proceeds and the exposed lumps of coal may disintegrate completely."

Nov 1, 1930

By M. Paczkowski

The use of inert gas systems to extinguish mine fires has been the subject of research for some time in the United States. In some European countries, it is an established practice. Tests were conducted with the CMI Inert Gas System (CMI), which is being used by the Polish mining industry. This system utilizes a modified jet aircraft engine and afterburner as a compact source of combustion products with a very low (less than one percent) oxygen content. Water injected into the combustion products stream provides evaporative cooling and forms a mist with a high cooling capacity. The CMI system was used under controlled conditions to extinguish coal pile fires at the U. S. Bureau of Mines Experimental Mine in Bruceton, Pennsylvania. The test results show that the CMI system can be used conveniently to extinguish fires quickly and to maintain an inert atmosphere in the fire zone to prevent re-ignition.

Jan 1, 1982

By ALICE V. Petar

Among the rarest of the rare metals are four that are linked together by a common historical background as well as by chemical relationship. With the excep- tion of indium, these metals are likewise characterized by the patriotic nature of the names given them by their discoverers. The existence of gallium, germanium, and scandium, was predicted by the Russian cherist, D. I. Mendeleeff some time prior to their discovery; and these elements might well have been overlooked, had not the search been stimulated by the urge to confirm the scientific hypothesis of their existence. Nowhare found in sufficient quantities to attract attention, these little known elemente are nevertheless widely distributed in the earth's crust. So far they are found commercially mostly in the sulphide ores of zinc and must be considered as being largely curiosities of the zinc smelter. Recent progress in electrolytic zinc refining, however, now gives promise that the way may be open for the recovery of these very rare metals in larger quantities-- possibly in quantities sufficient to permit of their finding commercial utilization.

Nov 1, 1930

By D. Harrington

Although it is impossible to give definite final figures at this time on Nation-wide accident occurrence in 1933 , enough data are at hand to indicate that the progress in safety in the mining industry, which first became apparent in 1930 and was accentuated in 1931 and 1932 , was continued and much improved in 1933. This improvement was of considerable magnitude in mining both bituminous coal and anthracite but was not so great in other branches of the mining industry . While the volume of work done in all phases of mining increased in 1933 over that in 1932 , the exact amount of the increase is not yet known . Usually increased activity in mining is accompanied by even greater increase in the rate of occurrence of accidents to the workers , but happily it appears that this " rule " was not operating in 1933 --at least in the coal -mining industry .

Oct 1, 1934

By R. M. GRANTHAM, J. H. SOULE

C. R. Keyes, F. C. Schrader , F. A. Jones ( the first director of the New Mexico School of Mines , whose name was given the deposits ) , and N. H. Darton all described the Jones iron deposits within a decade after their discovery in 1902 . The earliest locations now on record were made in 1927. Interest in iron ores was revived during the second World War . Paul E. Pesonen , of the Bureau of Mines , reported on the deposits in December 1941 and proposed an extensive exploratory program . In March 1942 , the deposit was reported upon by C. H. Johnson , also of the Bureau of Mines , and a definite program of exploration was outlined .

Feb 1, 1947

By T. T. Read

"Employee representation in the management of large mining enterprises was first introduced in organized form, by the Colorado Fuel and Iron Co. in 1915. Within the past few years a number of the larger mining enterprises have introduced similar systems and there is growing interest in the subject. This will be stimulated by the final report of the President's Second Industrial Conference, in which the following statement occurs:""The conference finds that joint organization of management and employees where undertaken with sincerity and good will has a record of success. The general principles governing such organizations are stated at length under the title 'Employee Representation. It is not a field for legislation, because the form which employee representation should take may vary in every plant. The conference, therefore, does not direct this recommendation to legislators but to managers and employees.""If the joint organization of management and employees in the plant or industry fails to reach a collective agreement, or if without such joint organization, disputes arise which are not settled by existing agencies, then the conference proposes a system of settlement close at hand and under Government encouragement, and a minimum of regulation. The entrance of the Government into these problems should be to stimulate further cooperation."""

Mar 1, 1920

By Carl Belser

This report is the first of a series dealing with the oil-shale reserves of the Green River formation in the Rocky Mountain Region. The known oil-shale reserves of northwestern Colorado at present considered to have economic value apparently are confined to the Piceanco Creek basin between the Colorado and White Rivers. The number of sampled sections is small, but there can be little doubt that the Piceance Creek basin is a potential source of enormous quantities of liquid fuels and the related byproducts obtained from oil-shale processing. The partly blocked and inferred oil-shale reserves of 25-gallon-a-ton shale are estimated to have an oil yield of 125 billion barrels and the reserves of 15-gallon-a-ton shale are estimated to have an oil yield of 494 billion barrels. The number of available sampled sections is inadequate for making firm estimates.

Jan 1, 1951

By C. E. Henning

The total number of petroleum refineries in the United States on January 1, 1958, was 318 and their total crude-oil throughput capacity was 9,407,707 barrels per day, according to the Bureau of Mines annual survey. During 1957, 3 new refineries began operating while 4 refineries were retired. Although there was 1 less refinery, the total crude-oil throughput capacity at the beginning of 1958 was 284,033 barrels per day, or 3 percent, more than the January 1, 1957, level. During 1957 all refinery districts showed increases in capacity. The largest increase, 27 percent, occurred in the West Coast district followed by the Indiana-Illinois-Kentucky district with 14-percent increase and the Texas Gulf Coast district with 13-percent increase. The national increase in capacity had the effect of raising the capacity of the average refinery from 28,601 to 29,584 barrels per day. New crude-oil capacity under construction on January 1, 1958, totaled 185,265 barrels, and an additional 297,885 barrels capacity was reported building as replacement for existing facilities. Included in total new construction were 2 new refineries, 1 in Washington and another in Texas, with planned processing capacities of 45,000 barrels and 8,550 barrels per day, respectively.

Jan 1, 1958

By Thomas O. Llewellyn

This U.S. Bureau of Mines (US8M) report presents a concise review on sources, processes, supply, and historical use patterns of domestic cadmium. It also covers a preliminary estimated cadmium material balance for the year 1989.

Jan 1, 1992

By William H. King

The Fannie Ryan deposit is situated about 9 miles northwest of Boulder City, Clark County, Nev. at an altitude of about 2,000 feet on the north side of the River Mountains. The deposit is covered by several unpatented claims owned by Fannie B. Gulick of Las Vegas, Nev. The Boulder City deposit is within the Hoover Dan National Recreational Area. It is situated about 3 miles southeast of Boulder City in sec. 23,T. 23 S., R. 64 E., Clark County, Nev. The Deposit was covered by several unpatented mining claims owned by S. R. Whitehead of Las Vegas. The deposits occur in sedimentary beds of the Muddy Creek formation that overlie older volcanic extrusive. The manganese minerals occur as soft oxides of the wad type. The exploration was conducted by the Bureau of Nines in cooperation with the Federal Geological Survey and comprised a study of the geology, mapping of the areas, and development by shaft sinking; diamond drilling, and sampling. On the Fannie Ryan Gulick property the work consisted of cleaning and sampling seven old trenches on the outcrop and diamond drilling seven holes totaling 1,482 foot. At the Boulder City deposit 188 feet of drilling was done in two holes. A 4- by 6-foot shaft was sunk to a depth of 44.5 feet, and the north and south sides of the shaft were sampled.

Jan 1, 1950

By W. L. O'Brien, E. A. Rowe

Electrorefined vanadium with additions of up to 5 percent by weight of yttrium, cerium , lanthanum , praseodymium, neodymium, and samarium was melted to ingots in a nonconsumable electrode arc in a helium atmosphere . The ingots were rolled into strips and evaluated for the effect of the alloying elements on hardness , tensile strength , ductility , recrystallization temperature , and microstructure . Except for samarium , average additions of alloying elements of 1 to 2 weight - percent resulted in the retention of 0.12 to 1.05 weight - percent in the alloys and reduced the ultimate tensile strength from about 48,000 to approximately 30,600 psi . The corresponding yield stress (0.2 percent offset ) was reduced from about 40,700 to approximately 20 , 200 psi . Diamond pyramid hardness (DPH) was reduced from 117 to an average of 62 kg /mm² . Increased malleability at room temperature resulted with yttrium and all rare - earth- metal additions , except samarium , particularly with more than 0.25 weight - percent additions . Decreasing oxygen contents corresponded with the changes noted in the mechanical properties of the alloys . The recrystallization temperature of electrorefined vanadium was reduced from approximately 950 ° to 800 ° C. Yttrium or a rare- earth metal content , except samarium , in excess of 0.1 weight - percent in vanadium produced a second phase suggestive of an eutectic which indicated a possible maximum solubility of less than 0.1 weight - percent for both room and elevated temperatures .

Jan 1, 1964

By W. T. Reid

A shortage of anthracite for home heating indicates the necessity of using other fuels for this purpose; low-volatile bituminous, or "soft" coal is the most feasible supplementary fuel, either burned alone or when mixed with anthracite. Comparison of Bituminous Coal and Anthracite Whereas anthracite is clean, burns without smoke, and requires little attention, bituminous coal is dusty, tends to burn with a smoky flame, and forms coke in the fire pot that must be broken up to maintain a continuous high output of heat. When properly fired, however, bituminous coal responds more quickly than anthracite to changes in damper settings and consequently can supply more heat in a short time. It is generally less expensive and usually contains less ash than anthracite.

Jan 1, 1943

By Eric R. Bauer

This Bureau of Mines publication describes and illustrates the physical signs of excessive loading on mine roof supports, installations, and openings. It is designed to assist mine personnel in recognizing potentially hazardous ground conditions, by emphasizing the preliminary effects of developing unstable ground. Increased worker awareness can be expected to reduce the injuries and fatalities resulting from falls of roof, rib, and face.

Jan 1, 1985

By Nicholas Kyriazi

A joint effort by the U.S. Bureau of Mines and the U.S. Mine Safety and Health Administration (MSHA) was undertaken to determine how well self-contained self-rescuers (SCSR's), deployed in accordance with Federal regulations (30 CFR 75.1714), survived the underground environment with regard to both impact damage and aging. This report presents findings regarding laboratory-tested SCSR's from 1982 through 1990. The SCSR's were tested on human subjects and on a breathing and metabolic simulator (BMS). These results indicate that most of the apparatus, if they pass their inspection criteria, perform as expected except for units with manufacturing defects or design deficiencies. However, when the apparatus are carried in and out of the mine daily and stored at the working section, they may suffer abuse. Physical signs of abuse, unless extremely obvious, are frequently not detected by the miners or mine operators. This poses a potential danger to a user in an emergency. Recommendations include improved training in inspection procedures.

Jan 1, 2010

By W. P. Huleatt, R. B. McCulloch

"The Big Four zinc-deposit, directly above the north bank of the Green Mountain Reservoir on the Blue River, Summit County, Cole., was discovered in 1937 by the present owner, Walter McDaniel, who lives on the property. Mr. McDaniel, together with members of his family, have worked the mine on a small scale since its beginning and have shipped quantities of sorted high-grade ore to the International Smelting Co. at Tooele, Utah, and the Combined Metals Corp. at Bauer, Utah. More recently, parts of the nine have been operated by lessees.The property had been examined previously by the Federal Geological Survey, and the geological report was made available' to the Bureau of Mines.The Big Four mining claim was located in 1937 by Walter McDaniel and his wife Frances,- who had been prospecting in the vicinity since 1933. The discovery of the high-grade zinc deposit caused considerable excitement, as it had not been regarded as a mineralized area.Mining was begun in 1937 and carried on until 1944 by Mr. and Mrs. McDaniel with the help of a few hired miners. During 1944, parts of the mine were leased: to various parties Who produced small quantities of ore but did no development work.Shipments during 1941 .totaled 752 tons; during 1942, 387 tons; and during 1943, 510 tons. From the beginning of 1944 to April of that year, 98 tons wore produced and shipped to Utah,Since the lessees began operations, a grade of 30 to 35 percent zinc has been maintained by careful sorting. No production has been recorded for 1945.The Big Four mine is situated on Colorado State- Highway 9 between Dillon and Kremmling on the south face of Green Mountain overlooking the Green Mountain Reservoir, a Federal irrigation project on the Hue River, Green Mountain rises 1,600 feet above the general level of the valley to an altitude of 9,408 feet and the surrounding terrain, i s correspondingly mountainous and rugged."

Apr 1, 1946

By Raymond B. Lucas

"Distinction between Tripoli and Diatomaceous EarthMuch confusion exists both in the literature and in the trade as to the proper use of the terms tripoli, tripolite diatomeceons or infusoriai earth, and kieseigunr. All of these terms are often used synonymously by the trade and even in mineralogists and other reference books. Actually, tripoli is a ma- is a material of definite and distinct physical and chemical properties and all of the other terms belong to a different material with just as definite and distinct properties.Originally the term tripolite (loosely called tripole) was given to a diatomaceous cart from Tripoli in Northern Africa. Dena (J.D. Dana, A System of Mineralogy 6th Ed.) calls this material tripolite and gives no authority for the use of the terms tripoli. Between 1880 and 1890 the deposits near Missouri, were opened and the material placed on the market as ""Tripoli"" no doubt due to its resemblance in some respect to the original tripolite or diatomaceous worth from Tripoli. Since that time the term tripoli has with increasing definitenesss been reserved for the Seneca material and other siliceous of similar origin and physical properties, while all siliceous material of organic origin, containing dilators, has been called diatomaceous earth (or its synonyms infusorial earth, kiselguhr, etc.). Rottenstone is sometimes classed with tripoli."

Nov 1, 1920

By V. A. Marple, K. L. Rubow, Y. Tao

"A personal diesel exhaust aerosol sampler has been designed and evaluated in both laboratory and field settings. The sampler uses size selective sampling for the determination of the respirable mass concentrations of mineral dust and diesel exhaust particulate matter found in underground coal mines. This design is based on the premise that diesel exhaust particulate matter is predominantly less than 0.8 um while mineral dust is greater than 0.8 gm. Operating at a flow rate of 2 L/min, the sampler consists of a 10 mm Dorr-Oliver respirable dust cyclone followed by an 0.8 gm cutpoint impactor and an afterfilter. Field evaluations consisted of sampling at 6 different locations in these underground coal mines. Measured aerosol concentration less than and greater than 0.8 um have been compared with a well characterized cascade impactor.Techniques must be developed for measuring the mass concentration of diesel exhaust particulate matter found in underground coal mines due to the health concerns associated with worker exposure to diesel exhaust particulate matter. Diesel exhaust particles are in the respirable size range and have been regarded as a potential occupational carcinogen by NIOSH (1988). Furthermore, a 1988 MSHA advisory committee directed MSHA to develop a sampling protocol for assessing worker exposure to diesel exhaust particles.The University of Minnesota and the Bureau of Mines, over the past 4 years have measured the size distribution of diesel exhaust particles and mineral dust, both in the laboratory and underground mines (Cantrell, 1987; Cantrell et al., 1987; Cantrell and Rubow. 1988; Marple et al, 1986; Rubow et al., 1988: and Watts et al., 1989). To date, measurements have been made in nine coal mines. Seven mines utilized diesel-powered equipment at the mine face while two used electric-powered equipment. The results of these field tests indicate that mineral dust and diesel exhaust particles can be differentiated on the basis of particle size. The measured particle size distributions have been found to be bimodal with a saddle point at 0.8 um. This has led to the hypothesis that one method for measuring worker exposure to diesel exhaust particles would be to collect size fractionated particle samples separated at 0.8 um with the diesel particles being less than 0.8 um and the mineral dust particles greater than 0.8 um.Aerosol size distribution measurements, using a micro-orifice uniform deposit impactor (MOUDI), have been conducted in the mine intake air portal, intake entry to the working section, haulageway, and section return entry. The MOUDI is a ten stage cascade impactor with particle cutpoints ranging from 0.1 to 15 um aerodynamic diameter (Marple and Rubow. 1984b; Marple et al., 1989). The sampling flow rate is 30 L/min."

Mar 1, 1992

By Juel H. Stears

Research was done to determine if a hydraulically operated penetrometer developed by the Bureau of Mines could be used to estimate the roof-bolt anchorage capacity of mine roof rock. Tests were conducted both in the laboratory using cement cylinders and underground in shale rock. Hardness readings were measured by the penetrometer around the periphery of the bolt holes at the anchorage horizon. Roof bolts Nere then installed and subjected to an anchorage test. The results showed that the penetrometer readings could be used to determine the optimum stratum for roof-bolt anchorage but could not be used to make an accurate estimate of the anchorage capacity.

Jan 1, 1965

By C. B. Manula

In this report, the application of the Open Pit Materials Handling Simulator (OPMHS) to a Southwestern surface mine using draglines and front-end loaders is described. The specific objective of the study is to demonstrate the application of the simulator to analyze mine planning and to analyze alternatives for increased production. The simulator was verified by comparing long term production figures to the simulated results from data collected on a mine visit. A short term and a long term alternative are studied with projected productivities and scheduling. No economic analysis of these proposals were performed.

Jan 1, 1977

By H. G. Iverson

The effects of adding boron and boron plus carbon to electrorefined vanadium were evaluated with respect to mechanical properties at low temperatures and response to heat treatment. Grain size was significantly decreased with the addition of 0.05 percent boron, the decreases ranging from 30 percent at 800° C to 75 percent at 1,100° C. Increasing the boron content resulted in only a small increase in strength at room temperature, but at 77° K, boron contents of 0.005 to 0.076 percent increased the yield strength of vanadium over 50 percent, from 70,000 psi to 110,000 psi. When boron and carbon were present together, the individual grain-refining effects obtained with either element were retained. Approximately a twofold increase in strength was obtained by age-hardening the alloys containing both boron and carbon. Alloys with only boron additions did not age-harden.

Jan 1, 1968