Search Documents

By Almon F. Robertson

The floor of Shady Valley, Johnson County, Tenn., is underlain by the Shady dolomite formation. In places the residual clay derived from this formation contains considerable manganese oxides. Nine properties in Shady Valley and two in Doe Valley were prospected by the Bureau of Mines from January 1943 to April 1943. The results obtained indicate that the ore bodies are small and spotty and, that the ore is not well-adapted to gravity concentration. The work of the Bureau was confined to the open end of the valley. One mile northeast of the Ham Greer property, Beaverdam Creek enters a rocky gorge, and it was believed that the few prospects in this area were of secondary impor-tance and, owing to the steep slope and general roughness of the terrain, that exploration with the rite', bucket-drill would be impracticable. A total of 4,398.5 feet was drilled in 131 holes. In addition, 235 lineal feet of bulldozer trenches were cut and 4.5 feet of test pits were sunk. The following nine properties were explored in Shady Valley: Bentley, Walker, Blevins, Scott, North Ham Greer, South Ham Greer, Lipford, Blackburn, and Steagall In Doe Valley, the Gerd Shoun and Brookshire properties were explored.

Jan 1, 1949

By Joseph E. Matta

The Bureau of Mines conducted a field study to investigate thin suppression of respirable dust by water sprays on a continuous-mining machine. Determining the importance of the top and bottom sprays for two types of spray nozzles was emphasized. Results showed, at a 90-pct confidence level, that (1) at least 70 pct of the dust was generated during the sump cut, even though nearly half of the coal was mined during the downshear operation, (2) the water sprays on the top of the boom had little effect in suppressing respirable dust, and (3) B.D. 5 spray nozzles mounted beneath the boom reduced dust at least 33 pet more than B.D. 5 sprays mounted on top of the boom. A single-cut technique was developed that gave good reproducibility for replicate cuts (coefficient of variation of 20 pct).

Jan 1, 1976

By H. P. Hermance

The Ely mine, which at one time was the largest producer of copper in the United States, has been idle for the past 30 years. A remarkably continuous ore shoot probably averaging 100 feet wide and 19 feet thick was mined on about a 25° slope for 3,400 feet on the incline. The ore was massive sulfides containing chalcopyrite, pyrrhotite, pyrite, and sphalerite. The estimated production of the Ely mine is 400,000 tons of ore averaging 3.3 percent copper. Because of the critical position of copper during the recent war, a search for extensions and recurrences of parallel ore shoots at the Ely deposit seemed warranted. The Bureau of Mines surveyed selected areas by geophysical methods, diamond-drilled nine holes, and sampled mine dumps during its investigations, which began in 1942 and terminated in 1946. The diamond drilling totaled 5,229 feet. The logs of the holes include chemical analyses of mineralized sections.

Jan 1, 1949

By Thomas C. Denton

The fluorite, deposit discussed herein occurs on a property known as the Snowball and comprises five contiguous mining claims in Maricopa County, Ariz. Attention of the Bureau was first directed to this property early in 1944 through .a request by D. B. Powell, original locator; to investigate his property as a possible source of fluorite and one that might 'Warrant exploration by the Bureau. The property was examined by two Bureau engineers, Thomas C. Denton and Geo. W. Huseman. It was decided to investigate the occurrence further by trenching, sampling, and diamond drilling. Work began on May 15, 194. Preparatory work, trenching and surface sampling, was supervised by Geo. W. Huseman. Drilling was in charge of R. M. Grantham. The project was completed August 8, 1944.

Jan 1, 1949

By Raymond L. Lowrie

For many years it has been considered that an average of 50 percent of the coal in the deposits exploited has been recovered. Owing to many changes in mining methods during the past two decades, this study was initiated to obtain an up-to-date measurement of recovery percentage and thus establish part of the basis from which presently recoverable reserves may be estimated. Recovery percentages were determined within mined areas of 200 underground coal mines. These comprised a statistical sample selected to be representative of operating mines in relation to their significance to depletion of reserves. The results ranged from 29 to 91 percent and averaged 57.0 ± 1.7 percent (95-percent confidence limit). Six factors were identified mathematically as significantly affecting recovery percentages: (1) Pillaring system, (2) top rock and conditions, (3) bottom rock and conditions, (4) marketability, (5) coalbed thickness, and (6) productivity. Skill and attitude of mine operators toward recovery, although not measured, were probable factors. Five other variables that were tested did not show any significant relationship with recovery percentages. Also, five mining equipment features were identified, through discussions with mine officials, as affecting adversely recovery percentage at some mines.

Jan 1, 1968

By Jalna R. Zatko

Coal-clay waste slurries were dewatered in laboratory-and small-scale continuous tests by the Bureau of Mines using polyethylene oxide (PEO) as a flocculant. Dewatering from a nominal 7-wt-pct solids to over 50-wt-pct solids was accomplished using 0.5 lb of PEO per ton of feed in small-scale continuous tests. Parameters such as pH, initial solids content, and PEO concentrations were investigated. Water recovered from dewatering was reused as dilutant for PEO solutions.

Jan 1, 1982

By C. N. Rosenecker

The power required to circulate a gas-solids suspension was determined using a centrifugal compressor and a closed system. The suspension consisted of 18- to 40-micron glass beads in a mixture of 89 percent N2 and 11 percent CO2 at 20 psig. Solids-to-gas (S/G) ratios w re O to 2.2 lb/lb; gas flow rates were l.2 to 2.5 lb/min. Power requirement was found to follow the relationship hp t = hp(. + l), where hp t = the total power, and hpg = the power required for pure gas.

Jan 1, 1967

By G. M. Molinda

The U.S. Bureau of Mines conducted an investigation to determine the nature and frequency of coal mine roof failure beneath valleys. A mechanism for this failure and suggestions for controlling this problem are presented. Hazardous roof conditions identified in some mines were positively correlated with mining activities beneath stream valleys. Mine maps with overlays of unstable roof and locations of stream valleys show that 52 pct of the instances of all unstable roof in the surveyed mines occurred directly beneath the bottom-most part of the valley. The survey also showed that broad, flat-bottomed valleys were more likely to be sites of hazardous roof than narrow-bottomed valleys. Evidence of valley stress relief was found beneath several valleys in the form of bedding plane faults and low-angle thrust faults. This type of failure, previously believed to be only a shallow phenomena, was found at mining depths as great as 300 ft. In situ, horizontal stress measurements beneath a valley and the adjacent hillsides, confirmed valley stress relief. Numerical analysis of 13 valleys overlying one mine property showed the effect of the valley excavation on horizontal and vertical stress.

Jan 1, 2010

By A. B. Hooker

Many attempts have been made to develop methane detectors that will be safer and more accurate than the flame safety lamps used to detect methane in mines. The development has taken two general forms, namely: (1) Methane detectors, in which the evidence of methane depends entirely upon changes in the appearance of the detecting element, such as a flame or filament; (2) indicating methane detectors or those equipped with scales upon which the approximate percentage is definitely indicated. As an aid in the development of suitable detectors, the United States Bureau of Mines has assembled and published in its Schedule 8B a set of minimum requirements which tests and experience have shown desirable for methane detectors. Any manufacturer may submit his detector for inspection and tests leading to approval under this schedule.

Jan 1, 1930

By Paul S. Goodman

This report examines the effectiveness of bonus plans in the coal industry. The analysis uses theoretical, literature review and empirical approaches to determine the impact of bonus plans on safety and productivity in underground coal mines. The basic finding is that the modal bonus plan in underground coal mining does not have a major impact on productivity and safety indicators. The design of the plan, or organizational factors, and the process of introducing the plan all contribute to its relative ineffectiveness. Strategies and options for designing effective plans are presented.

Jan 1, 1987

This section of Minerals and Materials analyzes the following three factors affecting the recent performance of the U.S. and world mineral industries: 1) the health of the U.S. and world economies, 2) the level of interest rates and 3) the performance of productivity in both the U.S. mineral industry and the general economy. While these indicators do not exhaust the possible critical factors, they represent an initial attempt to probe some of the considerations underlying the performance of the U.S. minerals and materials industry. The U.S. and World Economies It is essential to analyze the state of the U.S. and world economy because the demand for minerals and materials is a derived demand; that is, since minerals and materials are used in the productive process, the demand for them is a direct function of the demand for the finished products of which they are a basic input. Thus, the demand for minerals and materials is directly affected by changes in present and planned consumption and investment expenditures. The past two issues of this publication have highlighted the generally discouraging performance of the national and inter-national economies. Briefly, the world economy is in the third year of the first long recession in recent history where inflation rates have remained above 5 percent. With many countries either unable or unwilling to support domestic spending while inflation continues, there has been a growing tendency to institute trade-restrictive policies to support domestic demand. The resulting weakened demand conditions in exporting nations have had a direct effect on the mineral industry.

Jan 1, 1982

By Winthrop F. Watts

The U.S. Bureau of Mines evaluated the performance of a catalyzed diesel particulate filter (CDPF) and a CDPF combined with a diesel oxidation catalyst (DOC) at two metal mines. This report describes the results from the two field evaluations. The CDPF-DOC was installed on a load-haul-dump (LHD) powered by a 175-kW, prechambered, turbocharged engine. This system reduced diesel particulate matter (DPM) concentrations by 71±28 pet, as determined by size-selective sampling with gravimetric analysis, and by 71±29 pet, as determined by respirable combustible dust (RCD) analysis at the vehicle operator's location. The CDPF was installed on a diesel-hydraulic, roof-bolting jumbo, powered by a 172-kW engine. The CDPF reduced DPM concentrations by 72±21 pet, as determined by size-selective sampling with gravimetric analysis, and by 62±25 pet, as determined by RCD analysis at the vehicle operator's location. Underground evaluation was more difficult because of frequent movement by the roof-bolting jumbo, variation in daily workload, tremendous fluctuation in ventilation airflow rates, and use of a high sulfur diesel fuel, which promotes the formation of sulfate particles, decreases filtration efficiency, and hastens the deterioration of the catalyst.

Jan 1, 2010

By F. M. Goodwin, Campbell. John, W. J. Hiffs, G. W. Jones

"INTRODUCTION In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., and the Boston Consolidated Gas Co. a survey has been conducted continuously since 1929 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes of the Edison Electric Illuminating Co. The New England Telephone & Telegraph Co. also has cooperated in the investigation, and tests have been made in its manholes since May 1, 1933.Yearly reports 6 giving the results obtained since the start of the survey have been published.The method and procedure of conductin, the survey in 1935 were the same as heretofore.ACKNOWLEDGMENTSThe cooperative investigation was arranged through the interest and effort of F. D. Comerford, president of the Edison Electric Illuminating Co. of Boston; E. N. Farnesworth, Jr., vice president and general manager of the Boston Consolidated Gas Co.; and A. C. Fieldner chief engineer, Experiment Stations Division, U. S. Bureau of Mines. Thomas H. Haines, superintendent, Distribution Department, of the Edison Electric Illuminating Co., cooperated in furnishing men and information for the work,"

Oct 1, 1936

By Slavoljub D. Maksimovic

At some coal mines, methane gas is released during raise drilling. At the request of the Mine Safety and Health Administration (MSHA), U.S. Department of Labor, the Bureau of Mines conducted ventilation surveys at different raise drill sites to assess various methods of reducing methane concentration. The resulting data indicate that raise drill shaft cavities are ventilated by air compressors, vacuum pumps, auxiliary blower fans, and free intake air from the surface. The compressors, pumps, and fans operate simultaneously or separately. At the bottom of the shaft cavities, ventilation is controlled by regulators and airlocks. Methane is monitored, measured, and periodically sampled on the surface, at the bottom, and at different levels in the shaft cavities. Maximum concentration of 3.5 percent was measured in one shaft in West Virginia. Air velocity down the raise drill shafts is always very low, Maximum recorded air down the drill stem was 3,000 cfm, which can be increased by adding air compressors. The best way to ventilate shaft cavities is through the simultaneous use of air compressors and vacuum pumps. If the methane concentration cannot be reduced with additional compressors, then the inside diameter of the drill rod should be increased, or larger pilot hole drill bits should be used.

Jan 1, 1981

By Oliver Bowles

A conviction is growing that depressions and other adverse conditions are not entirely unavoidable if a knowledge of past achievements and shortcomings is intelligently, applied in shaping the course of industry. Mineral producers have available a source of such knowledge concerning; their industry in the statistical records of the United States Bureau of Mines, and by scanning, this increasingly exact history can obtain information on which to found a more stable future. This paper contains a brief history, covering more than 50 years, of the activities of the nonmetallic mineral industries as a group, followed by short histories of each of the more important commodities in which are noted the circumstances that lave influenced their development.

Jan 1, 1933

By Thomas W. Thompson

The Zebulon manganese deposit has been known for a number of years. It is situated about 3 miles east of Zebulon, Wake County, N. C., on the Avon, Privett property (fig. 1). The deposit outcrops as a vein, or dike averaging-16 to 20 feet in width. Drilling by the Bureau of Mines has shown that this outcrop results from consolidation of a number of small stringers near the surface. The surface width and the Percentage of manganese oxides (resulting from. weathering) diminish with depth. Below 50 to 80 feet, the vein material is mainly quartz and spessartite garnet. The deposit was first examined by W. T. Benson, a Bureau of Mines engineer, in 1941. The Bureau conducted a diamond-drilling exploratory program an the property from November 7, 1944, to January 25, 1945. A. total of 2,508.5 feet was drilled in 14 holes along the strike of the deposit.

Jan 1, 1950

By E. G. King

In continuation of the study of thermodynamic properties of the common interoxidic compounds of ferroalloy elements, this report gives the results of low-termperature heat-capacity measurements and entropy evaluations of the monotungstates of sodium, magnesium, and calcium. Previous reports4 5/ of this laboratory dealt with low-temperature heat capacities, entropies, and heats of formation of the sodium vanadates. Heat-capacity measurements of the monotungstates of sodium, magnesium, and calcium (Na2W04, MgW04, and CaW04) were conducted throughout the temperature range 51° to 298° K. The entropies at 298° K. were evaluated and then combined with entropy data for the elements and oxides to obtain entropies of formation. This information is an essential part of the data needed for thermodynamic appraisals of chemical reactions of these substances. No similar data for any tungstate are to be found in the literature.

Jan 1, 1961

By Frank B. Fulkerson

Three of the five primary aluminum producers in the Pacific Northwest have facilities in the region to make aluminum mill products. Only one of the three, however, produces a variety of shapes and forms. The principal reason for the lag in development of an aluminum mill products industry was found to be transportation cost. The long range outlook is for expansion, based mainly on growth of the western market for aluminum used in construction, containers and packaging, electrical applications, diesel trucks, mobile homes, and irregation pipe. Consumption of western aluminum mill products in 1985 is projected at 1.1 million tons, compared with estimated consumption of 250,000 tons in 1961.

Jan 1, 1965

By George W. Heim

Before and during World War II, the Bureau of Mines investigated a large number of ore deposits in the United States and Alaska in a search for domestic sources of strategic minerals. Deposits chosen for development included those expected to contain metals of importance in the successful prosecution of the war. This report describes the work performed and results obtained in developing the Daggett Chief manganese deposit near Manila, Daggett County, Utah (fig. 1), during 1941. The work comprised mapping and a study of the geology by the Federal Geological Survey, and bulldozer and hand trenching, sinking of two shafts, and sampling by the Bureau of Mines. Work was started April 17, 1941, and was completed June 28, 1941. Two bulk samples for metallurgical testing were taken.

Jan 1, 1950

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992