Search Documents

By Avery H. Reed

[The Bureau of rides is making a general study of the occurrence of the Clinton red iron ores of Alabama. In the course of this study, it developed that the iron-ore seams of the Woodstock and Bucksville areas were virtually unexplored., and the nature and extent of the ore deposits were undetermined. As a part of the work of the project, the Bureau investigated the occurrence of red iron ore in the .areas. Eighty-four channel samples, representing 317.6 linear feet, were taken from l2 locations along the outcrop of the red iron-ore seams, Ten diamond-drill holes, amounting to 3915.5 linear feet, were drilled. In these areas, commercial- and marginal-grade ores of minable thickness have been shown. It is estimated that 4,500,000 tons of indicated ore and 6,700,000 tens of inferred commercial-grade ore averaging 5.1 feet thick, 47.6 percent Fe, 26.1 percent insoluble, 0.1 percent CaO, and 0.04 percent P; 7,200,000 tins of inferred marginal grade ore averaging 6.1 feet thick, 36.2 percent Fe, .35.0 percent insoluble, 3.9 percent CaO, and 0.14 percent P; and 18,500,000 tons of ferruginous sandstone averaging 12.2 feet thick, 19.2 percent re, 50.1 percent insoluble, 9.6 percent CaO, and 0.14 percent P are present in the areas.. All tonnages are estimated as gross tons of recoverable ore in place, based' on 65-percent mining recovery. In accordance with established policy of the Bureau of Mines of publishing factual data as soon as possible after completion of field work, this description of the Woodstock and Bucksville areas is presented. As soon as work is completed in other areas additional reports will be prepared.]

Jan 1, 1953

By Walter Murphy

For a number of years the Bureau of Mines has been studying the properties of crude petroleums produced in the United States and the Western Hemisphere. A number of reports have been published giving the analyses of crudes from the different field and regions as made by the Bureau of Mines Hempel method of analysis.4/ Several of these reports include analyses off crude oils from the Rocky Mountain region.5/ The search for new fields and new producing horizons in old fields in the Rocky Mountain region has been quite intensive during the last few years, and a number of discoveries have been made.

Jan 1, 1937

By A. W. Frolli

This paper, describing the open-cut mining milling, and cyaniding methods and costs at the Yellow Aster gold mine, is one of a series being prepared by the Bureau of Mines on similar practices in the United States. It is presented primarily to show methods and costs of mining and treating low-grade gold ore on a large scale.

Jan 1, 1940

By Ad. Breyre

Internal-combustion engines have been used in Belgian mines for a long time. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they wore replaced later by electric or compressed air motors. However, the number of gasoline locomotives continued to increase. Regulations governing; the use of these locomotives seen were formulated and as early as 1920, when a new set of regulations was promulgated, these of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have been incorporated in the regulations.

Jan 1, 1940

By Ad. Breyre

[Internal-combustion engines have been used in Belgian mines for a long tine. As early as 1899, the use of these engines underground was considered, but the general policy was to prohibit such an application unless ministorial permission was granted' in special instances. At that time only gasoline engines were available, and a few of these were installed as stationary engines, although in general they were replaced later by electric or compressed-air motors. However, the number of gasoline locomotives continued to increase. Regulations governing the use of these locomotives soon were formulated and as early as 1920, when a now set of regulations was promulgated, the use of gasoline locomotives in mines could be authorized by the Provincial Inspection Department and no longer depended on obtaining a ministerial decision. Since 1931 this authorization may be given by the Chief Inspector of Mines, Director of the Mining District. Since 1920, safe practices have boon incorporated in the regulations.]

Jan 1, 1940

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1955 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 116 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers' 1955 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1956

By J. F. Barkley

"The fly-ash problem of the smoke-abatement engineer - who now might well be titled, ""Smoke and Fly-Ash Abatement Engineer"" - starts with the necessity for him to know what fly ash really is, what plants really create it, and how much is being created. Fly ash in this connection may be defined as all solid particles emitted to the atmosphere as a result of the combustion of fuel.COMPOSITION OF FLY ASHMuch can be learned about fly ash by studying samples with a strong magnifying glass or, preferably, a high-power microscope. As an example, figure 1 is a photomicrograph of an underfeed-stoker fly ash weighing 23.7 pounds per cubic foot, which passed a baffle-type cinder catcher and was caught by a Cottrell precipitator. Figure 2 shows a similar fly ash made at a higher stoker rating and weighing 36.2 pounds per cubic foot. The lighter ash contains more light, unconsolidated ash than the heavier. In both instances some of the ash has been fused to a glass, as is indicated by the spherical particles resembling marbles; however, the heavier dust contains more and larger spheres. With the faster burning and higher air pressures occurring at the higher burning rates, more of the larger fused spheres reached the precipitator.Such studies of fly ash frequently make possible correct determination of its source. For example, the Supreme Court Building, one of the finest of the Federal buildings in Washington, was having considerable difficulty with fly ash from some outside plant. It was thought to come from a nearby apartment house. A fly-ash trap was installed there, and care was taken in the operation of their underfeed stokers. The fly-ash nuisance continued. Microscopic examination of the fly ash found about the building compared with samples taken from the stack of the apartment house showed to the surprise of the accusing building superintendent that the present source was elsewhere. By the same means, the source was found to be a plant about ore-half mile away."

Sep 1, 1939

By Dennis J. Callaghan

This report is the result of information obtained from a review of related literature, personal inquiry and on-site examination of active surface coal mining operations. Four improved surface coal mine systems are described in detail and evaluated for feasibility, implementation requirements, environmental benefit and costs. Engineering feasibility emphasizes equipment availability, compliance to design requirements, practicality and industry rating. Implementation potential emphasizes immediacy, ease, acceptability and constraints. Special attention was given to environmental responsiveness, both with regard to the solutions to mined-land reclamation problems and to the concurrency of reclamation. Each system description includes a hypothetical model mine with a depreciation schedule, capital summary, estimated annual production costs, sales price computation, production and operating cost summary, and a sensitivity analysis of mine price to stripping ratio. A program plan and time schedule for demonstrating a selected mining system covers site selection criteria, mine data collection, criteria for controlling and budgeting costs and reporting findings. Ten additional mining methods and techniques are briefly described and evaluated. Common reclamation problems are listed and described. Sixteen state reclamation laws and regulations are abstracted. Sixty-nine references are listed in the bibliography.

Jan 1, 1976

There has been a substantial increase in the use of rubber-tired front-end loaders in the mining industry in recent years. Concurrent with this increased usage, in the period of 1966 to 1970, there were at least 74 mining industry fatalities involving front-end loaders, or (on the average) in excess of one fatality per month. When the usage of front-end loaders by the construction industry and other industries, organizations, and agencies, such as the Government (i.e., Department of Defense), along with the uncounted numbers of serious, but non-fatal accidents, are included in the picture, the safety record for front-end loaders, of necessity, becomes a serious subject for study. There is an urgent need for attempts to be made to eliminate or reduce the number of safety hazards; to decrease the confusing diversity of controls designs found on present front-end loaders; to improve the maintenance and operating procedures; to formulate better personnel policies; to increase management and official awareness of the extent of the problem, in both industry and the Government; etc.; in order to decrease the number of accidents. Part of the problem may be traced to the fact that the operator of a front-end loader is frequently designated a "heavy equipment operator." This implies that he is automatically qualified to operate any model, of any manufacturer's, wheeled or tracked, front-end loader as well as many other types and classes of heavy equipment. Contrary to automotive practice, the complement of primary operating and emergency controls varies widely from model to model, as well as from manufacturer to manufacturer. Not only are certain controls present on one front-end loader model and absent on others, but there are significant differences in the modes of control operation, in the functions performed by superficially similar controls, in the location of the various controls, etc.

Jan 1, 1973

By Fremont F. Clarke

"INTRODUCTION Clay beds of southwestern North Dakota were investigated to determine (1) the average alumina content of the clays in four principal areas of occurrence, (2.) which, if any, would be the most feasible method of extracting alumina from the clays, and (3) whether the clays had any other commercial uses.During the investigation exposed sedimentary beds were examined for clay and the thickness and areal extent of outcropping clay beds in the more promising areas were measured. Four-principal areas of bentonitic clays, comprising 6,967 acres in Stark, Slope; and Billings Counties, N. Dak., were mapped and sampled.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our natural resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chiefs analyzes samples and makes beneficiation tests.Acknowledgment is duo John P. Gries, professor of geology, South Dakota School of Mines and Technology, for his studies of and advice on geological phases of the work. His data were drawn on freely in preparing this report; also E. D. Gardner, regional engineer, Rolla, Mo., and E. Y. Dougherty, district engineer, Rapid City, S. Dak., for assistance and advice in supervising the program."

Mar 1, 1948

By Edward Keller

The work covered by this report was undertaken at the request of Dr. J. A. Holmes, late Director of the Bureau of Mines, to whom the writer had been recommended by C. W. Goodale and E. P. Mathewson, of Butte and Anaconda, Mont. The director's offer was accepted for the honor it conferred and for the useful results that might be promulgated by the work in the technical field covered. The investigation was facilitated by permission to visit various works and sometimes by contributions of important definite information on a given subject. It is therefore with pleasure that acknowledgment of courtesies is made to the following corporations and gentlemen: Anaconda Copper Mining Co., Raritan Copper Works, Baltimore Copper Smelting & Rolling Co., United States Refining Co., American Smelting &, Refining Co., B. B. Thayer, A. C. Clark, A. L. Walker, William H. Peirce, E. A. Cappelen Smith, H. H. Alexander, F. C. Newton, S. Rolle, R. W. Deacon, N. W. Pierce, O. C. Martin, C. N. Sappington, James K. Thomson, W. G. Derby, and the assistants of the writer, K. W. McComas and W. L. Raup. In this report considerable space has been devoted to general and theoretical principles on the ground that under modern conditions the best results in any field of activity can be attained only with the a. id of an adequate knowledge of the best theories underlying the practice. The diffusion of such knowledge in the field of sampling metallic metallurgical materials appears to have been quite insufficient, and it is felt that when the principles involved are once thoroughly comprehended their universal application will be appreciated, so that it will make no difference whether pig iron or gold bullion is offered for test. It may further be noted that a discussion of the theories underlying practical methods is placed under the caption "Practical Sampling," with the idea that no one can be a practical sampler unless he is capable of analyzing his methods. No attempt has been made to advocate any one method, but it is hoped that the analyses of all of the methods in use will show where each may be correctly and safely applied. The fact that it is possible to demonstrate the theoretical correctness of several methods indicates the invalidity of the claim that any single one of them is the standard.

Jan 1, 1916

By Sabri Ergun

Cost estimates and technical feasibility are compared for six chemical coal cleaning technologies. The comparison is based on conceptual application of the chemical cleaning methods for removal of pyritic and organic sulfur from a utility grade bituminous coal. The process layout includes receipt of 8,000 tpd ROM coal, fine coal pulverizing, desulfurization, and preparation of a compacted clean coal suitable for storage and shipment. The methods are: the Magnex iron pentacarbonyl process, the KVB dry oxidation process, the Battelle hydrothermal caustic leaching precess, the TRW Meyers ferric ion leaching process, the Ledgemont oxygen/water leaching process, and the Bureau of Mines/Energy Research and Development Administration air/water leaching process. Capital costs estimated for the desulfurization operation alone, scaled to 8,000 tpd, range between $14 MM and $122 MM, while estimated operating costs for desulfurization alone on the same scale of operation range between $7 and $17 per ton clean coal produced. Relatively little is known about the chemical cleaning of coal, and present cost estimates indicate that the method might not be competitive at its present state of development when used alone to clean utility grade coals for sulfur removal. The principal attractiveness of chemical coal cleaning lies in its potential for combination with physical cleaning to produce cost competitive compliance coals in a combined process with high-Btu yields.

Jan 1, 1977

By M. J. Beus, B. Stewart, S. Iverson

Synopsis U.S. Mine Safety and Health Administration (MSHA) accidents statistics have identified ore-pass hazards as a significant safety problem in U.S. underground metal mines. The statistics show that nearly 75% of injuries are directly or indirectly related to pulling or freeing of ore-pass chutes, the use of hand tools in ore passes, fails of broken rock in ore passes and structural failures of chutes or gates and ore-pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines. Risk assessment methods, such as fault-tree analysis, have been employed to identify the most probable causes of orepass failures, define research priorities and analyse the factors that result in malfunctioning and unsafe ore passes. Static and dynamic loads are being measured in a laboratory setting with the use of a reduced-scale orepass mock-up. Field tests are being initiated in mine ore passes to determine static and dynamic loads. Data from the test ore passes are being compared with data from the mine to characterize true system behaviour. Computer modelling with the use of closed-form solutions, finite-element analyses and a newly developed particle flow code predicts static and dynamic leads from the flow and the impact of ore and waste in the ore pass. Preliminary results indicate that dynamic impacts from ore and waste rock might be considerably greater than expected. The total static load is substantially less than is typically used fur the structural design of chute and gate support members. It is suggested that damping factors, normal and shear stiffness and mass frictional characteristics have a significant effect on particle flow and resulting impact loads. This is being verified with the use of results from laboratory tests, field tests and particle flow analyses. Ore passes are vertical or steeply inclined openings in a rock mass through which ore and waste are transported and where they mar also be stored. A typical underground mining system is shown in Fig. 1. The arrows indicate the locations of ore passes and loading pockets and their relative configurations. The control of material flow is potentially one of the most hazardous operations in underground mining. According to MSHA data. most of the ore pass-related accidents in the U.S.A. are associated with the loading-unloading cycle and removal of blockages from ore passes. In particular, attempts to free ore hang-ups have resulted in multiple fatalities. The hazards are obvious; there is uncertainty as to when the ore will break loose and miners are unable to escape falling rock to a safe location. Although ore passes and chutes and gate systems for underground metal and non-metal mines roust meet the requirements specified in the U.S. Code of Federal Regulations (CFR). Parts 57 and 75, recent structural failures of ore-pass linings and gates have underlined the lack of adequate ore-pass design standards available to both MSHA enforcement staff and mine engineers. Because of the importance of an ore pass to the safe operation of a mine design criteria need to be assessed and new guidelines developed. Researchers at the Spokane Research Laboratory of the Nationals Institute for Occupational Safety and Health (NIOSH) are investigating hazards in and around ore passes in hard rock mines and studying design criteria for ore passes. The near-term goal is to conduct laboratory and field experiments and computer modelling to evaluate the ore-pass design criteria currently used. Literature searches, field site

By Michael J. Beus

This Bureau of Mines report describes a field experiment involving the sinking of two test shafts to directly compare the deformational behavior of circular and rectangular shapes. Results show that the circular shape is less sensitive to geologic discontinuities and applied stress field. Also, the rectangular shape is subject to a variety of behavioral modes, including beam bending and buckling. Geologic discontinuities around circular and rectangular shapes influence displacement significantly. Simple, two-dimensional elastic finite-element modeling, simulating circular and rectangular shapes in a biaxial stress field, shows that the structural response of a shaft is largely controlled by geologic structure. Consideration of anisotropy may be required for realistic analysis of a deep shaft.

Jan 1, 1985

By C. A. Geffen-Fowler

This report, sponsored by the Bureau of Mines, presents the results of an examination of the safety of the Blind Shaft Borer (BSB) shaft sinking system and an alternative modified BSB design concept in comparison to conventional shaft sinking technology. Detailed study of the two systems was also performed to identify and recommend design changes for optimum safety conditions. A comparison of the BSB systems with conventional shaft sinking was made on the basis of relative risk levels. Risk incorporates both the frequency and the potential consequence of accidents. A safety evaluation of the component operations of the two BSB systems was performed using a Failure Modes and Effects Analysis (FMEA) methodology. The results of this analysis show generally that both BSS systems are safer than conventional shaft sinking. The potential risk of conventional shaft sinking operations could be reduced by over 30%, on the average, with the use of the original BSB system, and by an average of about 10% with the modified BSB. Design change recommendations to further improve the safety of these systems include a better fire suppression system, improved man haulage systems and more compact hydraulics. An operational safety manual was also developed for the modified BSB system.

Jan 1, 1981

The request for proposal from the U.S. Bureau of Mines outlined the purpose of this study in the following terms. "High grade near surface deposits are largely a matter of history. Most of the current mineral production in the united States is from large low grade ore deposits mined by large scale methods. It appears likely that exhaustion of near surface deposits and public resistance to open pit mining will tend to reverse the present trend toward open pit mining and lead to increased reliance on large scale underground mining. In view of the long lead time needed to improve basic technology, an in-depth study of the major underground mining methods is needed. "This study is intended to provide a systematic review and analysis of large scale non-coal underground mining technology with particular emphasis on current practices and problems, needed technological improvements, existing or potential environmental conflicts, and possible modifications or innovations that will assist in the satisfaction of projected national mineral supply requirements."

Jan 1, 1974

By Wilson Blake

Rock preconditioning in advance of mining was shown to be an effective means of rock-burst control based on the results of a field demonstration carried out on the 7700 level of the Hecla Mining Company's Star mine. Mining through the preconditioned zone was characterized by greatly reduced rates of released seismic energy and no bumping or rock bursting occurred within the preconditioned zone. Mining above the preconditioned zone was characterized by greatly increased rates of released seismic energy and rock bursting, particularly where the vein became very narrow in waste zones. This increased incidence of rock bursting points out the need for stope preconditioning to be carried out on an entire stope block basis. The data obtained from the monitoring of the mining above the preconditioned zone on the 7700 level will be extremely useful in evaluating any future stope block preconditioning experiments on the lower levels or the Star mine.

Jan 1, 1980

By R. Karl Zipf, Z. T. Bieniawski

"Fracture mechanics plays an important role in studies of geologic materials such as rock and coal. Yet fracture data are scarce for rock and most limited or unreliable for coal. A testing system was developed which can apply mixed mode loads to a crack tip in many rocks and geologic materials. It is possible to subject the test specimen to pure mode I, various mixed modes and a nearly pure mode II fracture load. The system is currently used to study the mechanics of fine fragment formation in various coals. Experimental measurements include KI and KII' fracture velocity and acoustic emission.INTRODUCTIONA major research program at The Pennsylvania State University is directed to understanding the fundamental mechanics of fine fragment formation in various coals. The program represents an effort to reduce the incidence of coal workers pneumoconiosis (black lung) in coal miners. The principal source of the respirable coal fragments is the cutting operation which forms and liberates the particles by a fracture process. Present understanding of the mechanics of the events which form and liberate these particles is meager (Cook, 1982).Current knowledge of the fundamental mechanisms of coal dust generation and entrainment in terms of the underlying fracture mechanics is critically needed to improve and possibly control the processes involved. Whether the cutting operation is done with a 'continuous miner' cutting machine, a plow or a longwall shearer, it is fundamentally a problem of mixed-mode crack propagation. When a cutting tool interacts with coal, it causes numerous cracks to propagate through the intact material. Numerous larger fragments are broken free, but another quantity of undesirable fine fragments is also created. The formation of these respirable fragments may be a direct result of the crack propagation process; hence, a thorough understanding of the fracture mechanics of coal is required to minimize production of the unwanted fine fragments.In most rock engineering applications, the rock material properties are of secondary importance to the rock mass properties; however, for rock fragmentation and rock cutting problems, it is rock material properties such as fracture toughness which are of prime interest (Bieniawski, 1980). Several rock cutting and rock failure theories have been proposed, but it is only very recently that fracture mechanics concepts have been successfully applied to the study of rock cutting mechanics. All cutting models seek to predict the cutting forces and the cutter geometry necessary to cause rock breakage and chip formation given some fundamental mechanical properties ~f the rock. Such models have wide applications in drilling, tunnel boring and mining problems. Nelson et al., (1985, 1986) has provided a very useful correlation between the laboratory measured fracture mechanics properties of rock and the performance of the disk cutters on tunnel boring machines."

Jan 1, 1989

By W. A. Calhoun, M. M. Fine

"One of the most important wartime activities of the Bureau of Mines was the search for new sources of mineral necessary to the prosecution of the war. Part of that effort was in the form of metallurgical service extended to other government agencies engaged in purchasing and stock piling some of the more critical and strategic materials.Fluorite was one of the materials stock piled by the Metals Reserve Company. The fluorite was usually in the form of coarse metallurgical con¬centrate purchased in the United States and abroad. The material was stock¬piled to insure an adequate reserve of fluorite for the metallurgical industries. The domestic production of metallurgical fluorite containing a minimum effective calcium fluoride content of 55 percent,4/ however, gradually increased until production was at least equal to consumption. The stock-piled metallurgical fluorite, therefore, soon became a surplus commodity.On the other hand, the supply of acid-grade fluorite, containing a minimum of 97.5 percent calcium fluoride and n maximum of 1.5 percent silica,5/ was never entirely adequate. Increased consumption of acid-grade material in the aluminum, petroleum, and chemical industries kept that material on the critical list during the war.Under the circumstances, it was felt that a study of the possibility of producing acid-grade fluorite from the metallurgical stock piles would be of some benefit to the war effort. Consequently, samples of fluorite from several of the Metals Reserve Company stock piles were tested by the Bureau of Mines at the request of the War Production Board.Two groups of samples were submitted for testing. One consisted of metallurgical fluorite purchased from Mexico and stock-piled in the El Paso and Laredo, Texas, stock piles of the Metals Reserve Company. The second group of samples was from the stock piles at Gila, N. Mex.The sample submitted from the El Paso stock pile consisted of about 5,000 pounds of minus 4-inch material. Mineralogically, the sample consisted of fluorite contaminated by calcite, chert, quartz, and small amounts of iron and alumina. Although some of the fluorite was reasonably free from gangue at minus 1-inch, much of it remained locked in sizes as fine as 65-mesh.The Laredo sample was about 5,000 pounds of material from five different piles. The samples from each stock pile, A to E, inclusive, were analyzed separately to determine whether the grade of the material in the piles varied markedly. As there was little difference in the analyses, the samples were combined in proportion to the tonnage represented to make a composite sample for testing. The composite sample consisted of fluorite with small amounts of quartz, calcite, and barite. Most of the fluorite was the dark-colored, opaque variety. A small amount of iron-oxide staining was present, and traces of muscovite, clay, pyrite, and tourmaline were noted. The quartz was present as crystals in vugs, and as finely disseminated grains in the fluorite. The druzy quartz and the calcite were free at minus 10-mesh, but the disseminated grains, some of which were 1 to 15 microns in size, were not entirely free at minus 270-mesh. A petrographic estimate indicated that 65 percent of the silica was locked in the 150- to 200-mesh."

Jun 1, 1946

By Will H. Coghill

The scope of this paper is such that it was deemed advisable to group the contents into several main sections. They are: Section 1. Geography and Geology. Section II. Historical Review. (a) Mining and Smelting in Alabama. (b) Milling. (c) Summary of Milling Research. These two sections are primarily a bibliography and summary of the research on the Birmingham Red Mountain ores up to the middle 1040's. Section III. Status of the Birmingham Iron Industry. This sect ion points out the extent to which the findings of the iron-ore research have been applied on a commercial scale. Also, a very brief description of the dependent and allied industries is included. The value of the Birmingham iron ore is greatly enhanced by the proximity of coal and dolomite. Thus the coal and coke industry and the dolomite industry are closely allied with and to a large extent dependent upon the possibilities of economic utilization of the Red Mountain iron ores. Section IV. Beneficiation Investigations of the Red Mountain Iron Ores. This is a record of the most recent, hitherto unpublished work of the Southern Experiment Station of the Federal Bureau of Mines, Tuscaloosa, Ala., on the chemical and physical composition not only of the Big seam but of most of the iron-bearing rock strata of Red Mountain.

Jan 1, 1946