Search Documents

By John S. Berber

Olefin and paraffin mixtures (C10-C16 and C10-C22) were separated from low-temperature lignite tar by urea adduction and sulfated to yield secondary alkyl sulfate detergents. The C10 ?C16 secondary alkyl sulfate showed a 99.3 percent biodegradability, and the C10-C22 fraction showed a 96.8 percent biodegradability, exceeding the required standard of 80 percent for the biodegradability of anionic detergents in washing and cleaning compounds. Chlorination of paraffins yielded a detergent of 93.2 to 93.4 percent biodegradability.

Jan 1, 1968

By H. William Zeller

The Bureau of Mines is conducting research to determine whether the use of chemical surfactants improves respirable coal dust control and is evaluating laboratory test criteria for selecting effective surfactants. This publication presents the results from wetting effectiveness tests with emphasis on the capillary rise test. The test variables investigated included coal particle size, type of surfactant, surfactant concentration, test duration, and mineral con-tent of the water. In addition to the rise test, measurements of con-tact angle, zeta potential, and sink time for various coal and surfactant combinations were conducted. No significant correlations among the four wetting tests were observed, a surprising result which implies that each test type measures specific aspects of the wetting phenomenon and also that each test type should only be used to select surfactants for specific applications. For example, the rise test shows solution penetration into porous materials, and the sink test discriminates among surfactants for dispersing finely ground materials into suspension. Another important conclusion is that combinations of agents retain their individual wetting properties, allowing mixtures to be for-mulated to perform well in both rise and sink tests.

Jan 1, 1983

By E. P. Youngman

From a scientific point of view , the zircon is by far the most remarkable of the gem stones , and a satisfactory solution of the problems offered by its characters and constitution has not yet been made . 3 Three distinct forms have been recognized , differing in specific gravity , hardness , optical properties , behavior when heated , and color.4 ( See section of this paper entitled "Description and Properties . " ) Zircon as a gem stone has not been as well known as its properties warrant . It is one of the most brilliant of the precious stones (having a high refractive index) . The colorless zircon rivals the diamond in brilliance and fire play to such an extent that a judgment based entirely upon optical inspection might be erroneous . In the opinion of gem authorities , the colored stones likewise have much merit . The blue zircon ( " Starlite" ) was so named by Kunz because of its resemblance to a " star twinkling in the night . " Another gem authority describes the leaf- green stone as one possessing a restful beauty , the red stone as having a certain ( though somber) grandeur , and the golden-yellow stone as being unsurpassed in magnificence . The slowness with which the zircon , a stone frequently mentioned in ancient literature , has come into use in modern jewelery may be owing to the fact that authorities differ as to whether the colorless and the blue zircons are found as such in nature or are treated stones . Any treated stone , although the material of which it is composed may be essentially genuine , has been considered a deception . However , according to Kunz , " Starlite is now sold over the entire world ; never has anything been so well introduced. "7 Dr. Foshag, mineral curator of the United States National Museum, states that the first allotment of zircons to enter the United States was obtained in 1921 from Siam ( through France ) for scientific or museum purposes and that four or five years later the stones were adopted by the jewelers of this country . Retail jewelers are displaying the colorless type and the blue stones , especially , in finger rings , necklaces , and like ornaments . Fine crystals have been used somewhat extensively in jewelling watches and as supports for the edges of fine balances . At one time zircons were though to be appropriate in mourning jewelery .

Jul 1, 1931

By James R. Boyle

The mining methods and practices used at the Young zinc mine, American Zinc Co. of Tennessee, have resulted in a low-cost, high-yield operation. Zinc ore (sphalerite) occurs in limestone-dolomite beds of the Kingsport Formation and is mined by modified room and pillar method. Utilizing trackless mining equipment which incorporates a high degree of flexibility, this operation has had a steady increase in productivity.

Jan 1, 1965

By Frank G. Horino

A rock mechanics program (composed of laboratory and field tests) was initiated by the Bureau of Mines in an effort to determine the causes of pillar instability at the Fletcher mine, near Bunker, Mo. Compressive strength, Young's modulus, shear strength, and the angle and coefficient of internal friction were determined on drill cores obtained from 16 different locations in the mine. Results of the laboratory tests showed that highly mineralized zones and brecciated zones in pillars could significantly affect pillar strengths and stability in locations where extraction ratios exceeded the normal design ratio of approximately 78%. High-angle fractures that were present in Some locations also may have contributed to pillar deterioration. In the field tests, in situ stress determinations were made in one pillar to establish the pillar-loading conditions and to evaluate the stability of the pillar. Continued monitoring of stresses in the pillar showed a gradual decrease in compressive stress, indicating that the pillar was probably in the postfailure state. A second stress determination was made in a vertical hole in the underlying igneous rock that was exposed on one section of the mine. Horizontal stresses were compressive and larger than would be expected from gravity loading.

Jan 1, 1978

By E. J. Matson

The Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. The Rush Creek lead-zinc deposit, Mono County, Calif. (fig. 1), was examined by W. T. Benson in July 1944 and again in September 1945 by D. W. Butner, engineers of the Bureau of Mines. From the results of these preliminary examinations, a core-drilling program (fig. 2) was started in August 1946 and continued until November 1946, when work was stopped on account of inclement weather. Field work was again started in May 1947 and completed in June 1947. The drilling program was laid out to develop the horizontal .and vertical extensions of showings exposed in surface pits.

Jan 1, 1949

By C. W. Huggins

The objective of this Bureau of Mines research was to compare the size distribution of respirable quartz collected at coal mines with that of several reference standards used to quantify quartz in coal mine dust samples. Particle size measurements were made on 23 samples and 4 ref-erence standards using a scanning electron microscope in the backscatter electron mode of operation, interfaced with an image analysis system. The Mine Safety and Health Administration provided the 23 respirable coal mine dust samples, which were collected at surface and underground coal mines in 7 States. The accumulated particle size measurements in-dicate three of the reference standards, minus 5-um Min-U-Sil, minus 5-um Supersil, and NBS 1878, would be preferred over the fourth, Silver Bond B, for quantitative quartz determinations in coal mine dusts by X-ray diffraction and infrared spectrometry.

Jan 1, 1985

By Stephen Utter

Stresses induced by block-caving mining were estimated from in-place measurements of strain or deformation in rock and concrete around mine openings. The four types of gages used for measurements in the Climax Molybdenum mine during 1959-61 were Whittemore gage, Carlson strain meter,2 Valore strain cell, and Climax extensometer. Gage performance in the laboratory was evaluated by stressing instrumented rock and concrete specimens in a universal testing machine and by comparing measurements taken by the gages and a standard gage. Gage performance in the mine was evaluated by comparing measurements taken during an 18-month test. The Whittemore gage, Carlson strain meter, and the Climax extensometer proved suitable for the investigation; the Valore strain cell, effective in the laboratory tests, gave erratic measurements in the mine.

Jan 1, 1965

By H. M. Smith

In studying the chemistry of lubricating-oil fractions from so-called ?paraffin-base? crudes, one of the first requisites is a method for the separation and removal of waxy material. A method utilizing solvents for this purpose is described in this report, together with preliminary experiments with solvents that led to its development. The solvents actually used are secondary butyl alcohol, acetone, and mixtures of these.. Isopropyl alcohol was also studied. Preliminary Experiments In previous work on "intermediate-base" crude oil, following the work of Wyant and Marsh acetone had been used for laboratory separations of oil and wax. Then acetone was tried for the separation of the waxes and oils of "paraffin-base" crude, the volume of acetone required (80 parts to 1 part of oil) was found to be too great for large-scale work. For this reason the effectiveness of other solvents was studied; the separation by acetone, however, was used as a standard.

Jan 1, 1927

By Helen E. Edwards

The Bureau of Mines is engaged in a systematic evaluation of the thermodynamic properties of combustion gases. These studies are designed to provide basic thermodynamic information of high accuracy facilitating the theoretical study of flame and combustion phenomena. This report is the third of a series3/ presenting results of the study for particular fuel-oxidant systems. The equilibrium composition of the products of combustion and the adiabatic flame temperatures of specified oxyacetylene systems have been computed.

Jan 1, 1953

By James S. Browning

The Bureau of Mines conducted laboratory and small--scale continuous tests of weathered mica pegmatite ores from Hart County, Ga., to determine the technical feasibility of recovering commercial-grade mica concentrates by flotation. Two modifications of the Bureau-developed anionic-cationic method were used. In one method, sodium carbonate and calcium lignin sulfonate were used for pH control and quartz depression; this method yielded mica concentrates containing 98.5 percent mica with a recovery of 91.4 percent. In the other modification, lime and sodium silicate were used with the calcium lignin sulfonate; concentrates containing 98.9 percent mica with a recovery of 86 percent were obtained.

Jan 1, 1966

By T. M. Barczak

One of the primary goals of Bureau of Mines research is to reduce the cost of coal mining by improving the efficiency of longwall supports. One method of achieving this goal is the optimization of stress distribution within the support structure, resulting in a lower overall weight, more fully stressed shield. However, before stress optimization can be initiated, load conditions must be defined that cause maximum stress in the various support components. A finite-element model of a longwall shield was used to identify these critical load conditions. These load conditions were then evaluated in the Bureau's mine roof simulator (MRS) by instrumentation of a longwall shield and measurement of strains in each of the shield components. The critical (canopy-base contact) load conditions were identified that can cause structural failure at less than rated shield (hydraulic yield) capacity. Comparisons were made between full-contact and partial-contact load conditions. Other parameters investigated included the stiffness of the contact material, changes in shield geometry, rate of load application, and effects of horizontal constraint. Conclusions were drawn regarding the structural integrity of the major shield components and potential for stress optimization.

Jan 1, 1987

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

By Phillip N. Yasnowsky

This Bureau of Mines report summarizes State severance taxes imposed on minerals and mineral fuels, provides a hypothetical example of how a State severance tax affects selected components of a firm's income statement, and uses the Bureau's Minerals Availability System (MAS) to estimate the effect of assumed changes in State severance tax rates on copper recovery cost at given levels of potential copper availability. A reduction of the rates to zero or a doubling of them results in changes in costs that are of the same order of magnitude as the cost of transporting copper to the United States from major foreign producing countries.

Jan 1, 1982

By Norman] [Seldle

This report describes the development of a mine machinery training system from initial conception through a task and skill analysis, a training system analysis, implementation of a prototype system, and initial validation of the prototype system. The objectives of the training are to improve safety and productivity simultaneously via complete, thorough training. A task and skill analysts was executed for shuttle cars, continuous miners, cutters, loaders, face drills, tractors, and scoops. The prototype training system is for shuttle car operator training.

Jan 1, 1976

By G. R. Hopkins, E. M. SEELEY

According to reports received by the Bureau of Mines, Department of Commerce, as of Jamary 1, 1930, there were 1,035 natural-gasoline plants in the United States, with a total daily capacity of 10,516,000 gallons. (These data do not include one small plant in Alaska.) The last similar survey, that of Jamary 1, 1928, showed a total of 1,155 plants of 8,048,000 gallons daily capa- city. This in two years time the number of plants has decreased by 120, but the total capacity has increased 2,468,000 gallons or 31 per cent. This is roughly equivalent to the gain in production over the same periodi Over half of the increase in total capacity was registered in California, where the development of flush oil production having a comparatively high gas-oil ratio in such fields as Santa Fe Springs led to construction of some new plants and material enlargement of others. Of the total plants, 999 were operating on Jamary 1, 1930, and 36 were shut down. This compares with 1,060 operating and 95 shut down two years ago, which indicates a tendency to dismantle plants as soon as they become obsolete or umrofitable. The total daily capacity of the plants operating on Jamiary 1, 1930, amounted to 10,278,000 gallons, or 98 per cent of the total, leaving only 238,000 gallons, or 2 per cent, for the shut-down plants. This contrasts with the refining industry, which usually has 5 per cent of its total capacity idle; the difference is due to the relative ease with which a refiner can secure a crude supply as against the difficulty the natural gasoline manufacturer has in reestablishing his gas connections. During 1929 the average total daily capacity of the operating plants was 9,899,000 gallons, while the average daily production amounted to 6,015,000 gallons. This indicates that the plants operated during 1929 at 61 per cent of their capacity. Although over 60 plants were dismantled in Oklahoma during 1929 the State continued to rank first in total mumber. California was second in mumber of plants with 165, and was one of the few States that showed a gain since the

Jul 1, 1930

By W. E. Robinson

A laboratory study wan made to determine whether drying and preheating Colorado oil shale with waste retort gases has any appreciable effect on its oil yield. Samples of crushed oil shale were heated at subretorting temperatures in a specially constructed electric furnace by gases similar in composition to waste gases from oil-shale retorts. The results of this study showed that preheating oil shale with nitrogen or a reducing mixture had no effect upon the oil or water yield. However, oxygen in the preheating gas caused a decrease of oil and an increase of water. In general, the oil yield decreased with (1) increase in oxygen content of the heating gases, (2) increase in temperature of the heating gas, (3) increase in heating time, and (4) decrease in the particle size of tho shale. The decrease in oil and the increase in water resulting from preheating were due to oxidation of the benzene-insoluble organic material (kerogen) rather than to oxidation of the benzene-soluble organic material (natural bitumen) in the shale, A small amount of oil was volatilized during preheating, which would constitute an additional loss if prober precautions were not taken to recover it. The results obtained in this laboratory study indicate that oil shale can be preheated without appreciable decrease in oil yield by proper selection of preheating conditions.

Jan 1, 1951

By John M. Gomes

Two molten salt systems were evaluated as electrolytes for the repetitive recovery of tungsten from tungsten oxide (W03) made by calcining commercial-grade ammonium paratungstate. Using a sodium chloride-sodium fluoride-potassium aluminum tetrafluoride electrolyte at 800° C, 1 pound of 99.8 percent tungsten was recovered for each 2.7 kilowatt-hours of energy consumed. The metal contained 1,100 ppm carbon, was in dendritic masses of spherical grains, and had an apparent bulk density of 5.41 g/cm3. T ngsten of 99.9 percent purity was won from a sodium pyrophosphate-sodium tetraborate-sodium chloride electrolyte at 1,000° C; 6.0 kilowatt-hours of energy was consumed for each pound of metal recovered. The metal contained 120 ppm carbon, was in dendritic masses of hexagonal acicular crystals, and had an apparent bulk density of 7.25 g/cm . Each metallic impurity--aluminum, calcium, copper, iron, nickel, and silicon--in the two tungsten products was 16 ppm or less.

Jan 1, 1966

By Vernon C. Davis

"INTRODUCTION This report describes the work done and presents the data obtained from limited diamond drilling at the lead-zinc deposits cf the Belle Eldridge Gold Mines, Inc., in Lawrence County, S. Dak. during the summer and fall of 1943. The work was undertaken in an effort to increase reserves and step-up production of zinc and lead so vitally important to the war program.The geology, topography and existing mine workings were mapped and studied. Subsequently, six vertical core-drill holes were put down from surface sites.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our natural resources to the end that they make the greatest possible contribution to national security and economy. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, Oliver C. Ralston, chief, analyzes samples and makes beneficiation tests, if such are necessary.Special acknowledgment is made to John Paul Gries, geologist, South Dakota School of Mines, for mapping and interpretation of geology and topography, logging of cores obtained, and his assistance in guiding the drilling."

Mar 1, 1948

By J. C. Holtz

Since 1937 the Bureau of Mines has conducted investigations to provide the technical information necessary to guide the safe use of diesel engines underground in the United States. Coincident with the beginning of the technical study, a survey was made of State regulations pertaining to the use of internal-combustion engines underground.3/ At that time it was found that owing to the known hazards of gasoline locomotives, many States had enacted legislation or regulations limiting or prohibiting their use underground. Some of this legislation prohibited, or could be interpreted as prohibiting, the use of any type of internal-combustion engines in underground workings. After World War II diesel-powered equipment was introduced underground in many States, and pertinent questions are received frequently by the Bureau of Mines about the regulations that permit such applications. Because it was known that new and revised regulations had been made effective in some States in the nearly 20 years that have elapsed since the previous survey,3/ the Bureau decided that a review of the latest regulations in the leading mineral-producing States would be a valuable source of information for those engaged in the production of minerals as well as others. Accordingly, where feasible, this report includes abstracts of State laws and regulations as they affect the use of internal-combustion engines underground, particularly diesel engines. The substance of comments from State officials also are included when these appear to be helpful to interpretation of the regulations.

Jan 1, 1957