Search Documents

By John M. Gomes

A two-phase molten halide-silicate technique for extracting tungstic oxide (WO3) from scheelite (CaW04) and wolframite [(Fe, Mn)W04] was investigated. The halide phase extracted over 99 percent of the was, whereas the lower silicate phase retained about 90 percent of the calcium, iron, or manganese oxides. The most efficient extraction and separation of tungsten from scheelite was accomplished at 1,080° C in a molten system containing, in mole-percent, 9 calcium tungstate (CaW04), 42 sodium chloride (NaCl), 28 sodium fluoride (NaF), 17 sodium metasilicate (Na2SiO3), and 4 alumina (Al2O3). Wolframite was also treated at 1,0800°C; the molten system contained, in mole-percent, 11 (Fe, Mn)W04, 74 NaCl, and 15 Na2 SiO3.

Jan 1, 1968

By John R. Dudo

The Bureau of Mines Morgantown Petroleum Research Laboratory, with the cooperation of the Penn York Oil Company, cored the Dewdrop, Bradford Third, Lewis Run, and Sartwell sands in the Sartwell oilfield, McKean County, Pa. This report contains a review of the geology and depositional history of the field and an evaluation of the feasibility of secondary recovery of oil from the Bradford Third and Sartwell sands by waterflood or gas drive. Core analysis, geologic data, and electrical and radioactivity logs were used to evaluate the reservoir characteristics. Reservoir geometry, rock properties, fluid characteristics and saturations, and relative permeability-saturation relationships were used to assess the floodability of these two sands. The results of this study indicate that between 53,000 and 61,000 barrels of oil can be recovered by water or gas injection. The success of a waterflood or gas drive will depend on the field injection rates of the reservoirs comprising this oilfield. Following an economic evaluation, additional field work is recommended to further test the floodability of the reservoir.

Jan 1, 1967

By Frank J. Wiebelt, Spangler Hicker

The Iron Mountain investigations were part of a comprehensive program for making a national inventory of raw materials used in the production of steel. A tentative program of core drilling by the Bureau of Mines was set up for exploration of more promising iron deposits. Iron Mountain was selected as worthy of investigation because it could serve as a potential source of ore for the war-created steel plant at Fontana, Calif. The deposits were reported on by an engineer in October 1943. The purpose of the project was to determine the lateral and vertical extent of ore bodies and to obtain accurate material data on them.

Apr 1, 1948

By Joel N. Van Sant

The rapidly expanding economy of the West, with its growth of heavy industry, and increased steel production, is primarily responsible for the refractory clay industry's concern over the adequacy of the clay supply in States of the Great Plains and Rocky Mountains. Hence, the investigation by the Federal Bureau of Mines of the occurrence and use of refractory clays in North Dakota, South Dakota, Nebraska, Wyoming, Colorado, Utah, New Mexico, and Arizona has been encouraged by the major consumers and producers of this commodity. The Wyoming investigation is a part of the national program devised to close gaps in the domestic supply of specific types of clays to determine their characteristics and properties and to provide information that will assist the refractory-clay industry. Forty-two locations of clay-bearing rock in 17 areas in Wyoming were examined (fig. 1). Location 3 was not examined during this survey. Its description was taken from an earlier report. Locations 20, 21, and 22 were previously reported but were, also, examined by the Bureau. No samples were collected from these locations because field examination indicated that the shales were not refractory grade. The Hulett, Aladdin, and Newcastle areas are discussed in the section on the Black Hills district; the other 14 areas are described separately.

Jan 1, 1961

By C. W. Van Noy

The procedure suggested in this report is intended for the use of engineers, esters, accountants, etc., in estimating the cost of chemical-type operations. It is intended to over operating costs, not investment costs, as the latter have been covered numerous other publications. However, as capital investment costs are reflected to a high degree in operating costs, it is important to point out that accuracy of investment costs is highly essential. Therefore, all factors that might be included under plant -capital costs should be considered, such as requirements of shops, employees' housing, etc. The procedure is designed primarily for use in types of chemical oper¬ations, such as the production of synthetic liquid fuels, anhydrous ammonia, and others of like or similar nature. Yet, no attempt has been made to cover the entire chemical industry.

Jan 1, 1949

By James Spiers

This paper describing the mining practice at the Central-Eureka mine is one of a series of similar papers being prepared by the United Staten Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The mining practices described in this paper are illustrative of the methods employed in the exploitation of comparatively low-grade gold ores under the extremely heavy and swelling ground conditions which occur in the Mother Lode belt of California. The Central-Eureka Mining Co. comprises a group of adjoining mines in Amador County near Sutter Creek. The principal mines of the consolidated group are the Central-Eureka, formerly known as the Summit mine, and the Old Eureka mine, which is also known as the Hayward Quartz mine. The group is situated in the most productive part of tae main Mother Lode belt, the 10-mile portion which lies between the towns of Plymouth and Jackson. The three largest producing mines of the entire belt at the present time are the Argonaut, Kennedy, and the Central-Eureka; these lie within a radius of less than 1-1/2 miles.

Jan 1, 1931

By W. E. Cooper

The International Intercalibration and Intercomparison Program (HIP), consisting of several selected laboratories from four countries, held a radon progeny intercomparison measurement at the U.S. Bureau of Mines experimental Twilight Mine on September 12-14, 1988. Grab samples were taken at four different conditions of low and high radon progeny and condensation nuclei concentrations, respectively. The results showed good agreement among all seven participants. The coefficient of variation of all measurements was 4.7%; after minor corrections for flows and some systematic biases, it was reduced to 3.2%.

Jan 1, 1990

By P. M. Ambrose

This report describes an accident, which took place in the Chemical Corrosion Laboratory at the College Park, Md., Station of the Federal Bureau of Mines. The accident occurred while Walter L. Acherman, chemist, was performing a routine manipulation during a corrosion experiment involving commercially pure titanium and red-fuming nitric acid. There was a sudden and very violent reaction, and a large quantity of acid was thrown in the face and over the body of Acherman, causing serious injury. L. B. Golden, chief of the Chemical Corrosion Section, was exposed to nitric acid fumes during the ensuing rescue and first-aid operations and died on January 25, 1954. According to the medical report, the direct cause of Mr. Golden's death was pulmonary edema and confluent bronchopneumonia; the contributary cause, was inhalation of fumes from red fuming nitric acid. The following employees of the College Park Station contributed to this report by supplying information on the accident and assisted in the rescue operation: L. B. Golden, chief, Chemical Corrosion Section; T. E. Green, chemist; Robert Warf field, chemist; L. A. DeVivo, laboratory mechanic; D. W. Chalkley, laboratory mechanic; E. H. Neagle, laboratory welder; and R. L. Heath, laboratory general mechanic.

Jan 1, 1955

By G. M. Potter

During investigation of the occurrence of manganese deposits in the western United States, the Bureau of Mines collected 2-ton samples of 4 ores from 3 properties in northeastern Nevada. Laboratory tests were made to determine the amenability of these ores to ore-dressing methods of concentration. The Caviglia-Vietti property is situated 11 miles southeast of Ely, White Pine County, Nev. The ore deposits are lenticular veins and irregular masses found in limestone fracture zones and along the contact of limestone and underlying shale. Two samples, of the ore were tested: Lot A, from the Vietti shaft, and lot B, from the. Caviglia shaft.

Jan 1, 1954

By J. F. Papp

The microstructures of a CF2Br2-inhibited methane flame and its uninhibited analog have been determined using molecular beam-mass spectrometry. The slightly lean flames were stabilized on a cooled porous plug burner at reduced pressure. Composition profiles of stable, intermediate, and radical species and temperature profiles were obtained. Comparisons of the uninhibited and inhibited flame profiles revealed the following inhibition effects; a shift of the primary reaction zone to higher temperatures, a higher maximum flame temperature, an increase in the CH3 concentration, and a reduction in the H2CO, H, 0, and OH concentrations. Kinetic analyses of the data yielded rate coefficients at flame temperatures for the reactions H + CH4 ? CH3 + H2, H + O2 ? OH + O, CO + OH ? CO2 + H, and CH3 + O ? H2CO + H. CF2Br2 is judged to decay by thermal decomposition and abstraction reactions.

Jan 1, 1981

By Charles M. Mason

The Bureau of Mines evaluated equipment and procedures for drop-weight testing of explosive liquids as prescribed by Test 4) a widely used method. It was demonstrated that partial ignitions, originally designated as negative results, should be designated positives; it was also shown that wear or erosion of the sample cups and the type of mount used for the apparatus had important effects on the results. Relative sensitivity as measured by Test 4 was found to vary slightly with temperature. The Bureau also designed a fixed 2-kg weight and associated electromagnetic release, which subsequently were incorporated as standard in a revision of Test 4. The original concept that the test involves only adiabatic compression was found to be an oversimplification; an alternate mechanism for the initiation process is proposed in which due consideration is given to the effects of cavitation and microjets.

Jan 1, 1966

By A. Sainato, S. J. Schatzel, D. M. Hyman, J. C. LaScola

The Bureau of Mines determined the gas contents of 135 oil shale samples obtained from approximately 630 ft of core drilling. Drilling was done within a projected mining zone of the Cathedral Sluffs Mine, located in the Piceance Basin of western Colorado. Methane contents were determined by the modified direct method, which can measure the volumes of several gases released from or reacted with mine rock without destructive sample treatment. Over the duration of the test, nitrogen was largely unreactive, CO2 increased slightly, oxygen decreased markedly, and methane increased more than the total increase of all contained gases. The gas volumes were normalized per unit sample mass and are given in cubic centimeters per gram. Common time irzdices for test duration of 3, 40, and 125 days were used to compare methane desorption among samples. The means of the sample populations for these indices were 0.0316, 0.114, and 0.195 cm3/g, respectively. These quantities are lower than those reported in a Bureau emissions study at the Horse Draw Mine in the Piceance Basin. Oil shale samples that were gas enriched beyond the mean methane contents frequently contained bitumens and pyrite.

Jan 1, 1987

By J. M. Singer

The Bureau of Mines investigated the threshold of dispersal of monolayers and piles of rock dust, anthracite, and Pittsburgh seam coal dust in a small wind tunnel that simulated a coal mine gallery, with the objective of preventing or limiting the formation of flammable dust clouds. The effect of selected variables on entrainment velocity was examined. Mode of entrainment and flow processes in the wake region of dust configurations were investigated by means of high-speed motion pictures. Significant results were as follows: 1. Local minimum air velocities required for dispersal were only slightly higher for shallow dust ridges than for dust particles. 2. Minimum velocities for entrainment of dust particles from smooth glass and coal surfaces increased in the order rock dust, anthracite, Pittsburgh seam coal. 3. The mechanism for dispersal of dust poles depended significantly on dust pile geometry, cohesiveness of dust, bulk density and compaction of dust, adhesive surface, and vibrations perturbing the supporting surface.

Jan 1, 1969

By R. H. Fewkes

New information on possible resource value of sea floor manganese nodule deposits in the eastern North Pacific has been obtained by study of records and collections of the 1972 Sea Scope Expedition. Nodule abundance (percent of sea floor covered) varies greatly, to judge from bottom photographs from 8 stations and data from other sources. All estimates considered reliable are plotted on a map of the region. Similar maps show the average content of Ni, Cu, Mn, and Co at 89 stations from which 3 or more nodules were analyzed. Variations in nodule metal content at each station are shown graphically in an appendix, where data on nodule sizes are also given. Results of new analyses of 420 nodules from 93 stations, for Mn, Fe, Ni, Cu, Co, and Zn, are listed in another appendix. Relatively high Ni+Cu content is restricted chiefly to four groups of stations in the equatorial region, where group averages are 1.86, 1.99, 2.47, and 2255 weight percent. These and a few other areas may warrant more exploration. It is hoped that this report will stimulate new interest in North Pacific nodule deposits and that the maps and quantitative data will aid future exploration.

Jan 1, 1981

By D. S. Burgess

An investigation of the hazard of spillage of liquefied natural gas (LNG) onto water is described. About 2,000 gallons of LNG were consumed in various tests. The initial vaporization rate of LNG following spillage was found to be 0.037 lb/ft2 sec; when the spill was confined, this vaporization rate was moderated after about 20 seconds by the growth of an ice layer on the water surface; when the spill was unconfined, a coherent ice floe was not observed and the vaporization rate was essentially time independent. The maximum diameter (in feet) of the spreading LNG pool was found to be given by 6.25 Wo 1/3, where Wo is the weight of LNG in pounds, Downwind of a natural gas source, time-averaged methane concentrations were given in good approximation by standard air pollution equations. However, peak concentrations were as much as twentyfold higher than average, adding an additional factor to the assessment of hazard. The effect of layering by the cold vaporized natural gas was similar to the effect of a temperature inversion on normal gases in the atmosphere. Small-scale explosions were observed on pouring LNG onto a water surface; no single explanation seems pertinent to all of the incidents observed.

Jan 1, 1970

By H. P. Hamlin, W. A. Grosh

Samples of clays , shales , and argillites from 21 locations were subjected to preliminary bench- scale tests for bloating properties , and several samples were tested for ceramic properties . Samples showing favorable bloating properties were further tested in a pilot - plant - scale rotary kiln . Physical characteristics and concrete -making properties of the bloated products were determined . The Decorah shale from one area made a suitable material for a lightweight aggregate ; however , the limestone layers in the formation must be eliminated or the resulting activated lime must be controlled by quenching .

Jan 1, 1963

By J. R. Thoenen

During 1928 questionnaires covering the calendar year 1927 were sent to over 1700 quarries: producing stone for purposes other thaw cutting to dimension. These inclined producers of stone for limn burning; cement manufacture, rip rag, and crushed stone. The various rinds of stone represented were limestone, trap rock, sandstone, granite, and marble. Replies received from limestone producers prior to November, 1928, were compiled into tables and published in February, 1925, as a preliminary report (Bureau of Mines Report of Investigation 2911).

Jan 1, 1930

By A. W. Deurbrouck

Five preparation plants employing concentrating tables for washing 3/8- inch to 0 raw coal were tested. Two of the plants were washing Pittsburgh-bed coal, two were washing Pocahontas-bed coal, and one was washing Elkhorn-bed coal. Samples of the feed to and products from the tables were collected over the normal operating shift. These samples were analyzed, and complete performance criteria were determined. The results of this study show that the concentrating table is an effective fine-coal cleaner even when operating at 40 percent over the recommended 10 tons per hour feed rate. Recovery efficiencies for the 3/8-inch to 200- mesh size fraction ranged from 97.3 to 99.3 percent; maximum yield errors and ash errors were 2.4 and 1.0 percent, respectively; probable errors ranged from 0.074 to 0.115 specific gravity units and error areas from 52 to 73 square centimeters. The amount of minus 200-mesh material in the water used for feed water and dressing water to the table had no significant effect on the sharpness of the separation achieved but did have an effect on the ash content of the clean- coal product. In the one plant studied, the substitution of fresh water for plant circulating water reduced the ash content of the clean coal by about 6 percentage points.

Jan 1, 1963

By Geoffrey G. Huggins

Discussions are presented of the three phases of the noise reduction program on flight-type coal conveyors. The three phases are identification of noise sources, evaluation of potential noise reduction concepts, and implementation of noise reduction which is intended to reduce conveyor noise to less than 90 dB(A) in the underground mining environment. The major noise sources are impacts of the chain on the tail roller and on the top and bottom decks. A total noise reduction of 11 dB(A) was achieved by using techniques which are applicable to retrofit. These are a vibration isolated tail roller and an isolated wear strip on the return deck. A theoretical model of isolation provided by the isolated tail roller is developed. Appendices are presented which contain information on other potential concepts and additional data generated.

Jan 1, 1976

By F. G. Miller

[Petroleum tscknologists nnd progressive operatorr. constantly are striving to increase the percentage of oil thnt may be recorered from reservoir rocks through wells. The exhaustive studies that hve boen made of the function of natural gas in the production of oil, for example, havo aided operators greatly in increasing tho quantity of oil recovered from reservoirs. Natural gas dissolv.3d in and otheraiso asnociatod under pressuro with oil in rsservoir rocks, howovor, is not tho only source of energy available for rnovi~~ oil through sands to wells. In becomine Veservoi~enorgy conscious^^ encineera havo lonrned that in nnny petroleum resorroirs the edgewater flanking the oil accurrulation constitutos a potantinl source of enorgy cnpnblo, through pro1,sr control, of increasing oil-recovory officioncies materially. ?To longer is tho oncronchmont of mter into the oil- and gas-fillod uart of tho reservoir conridsred as evil to be combatted by dovious mothods but rnthar a nrtturrtl consequence, incident to the withdraval of oil nna gas from tho rolls, thnt mP.y be used nd~~mtngeoualy in lengthening the flowing life of wells ,md incre~sing the oconornic recovery nf oil and gns. Little is knom a3out tho nac'n-~nisrn by mhich wnter qor-rtos in driving nil through reservoir rocks, nnd thjro is n scnrcity of published informa- tion on rates of rnovzrnant of ~ntcr +,hat will result in naxilnm oil recoveries. Bureau of Xine s er.gir.ess nr r'reciate the ~aucity of scientific knowledge on the best methods of lying the natural rater drive to in- crease oil-recovery efficiencies arid ar9 initiating stildies that rill, they hope, contributo to tho procont small fund of information now available on the subject. This rh~.ort is s syr,o_nsis or brief c03pilation of published dAta and thought nccumulntod 30 far, groliminary to la-uorgtory ox~eriment+ tion NI& further resaarch on the principlgs und~rlying the nnturnl wnter drive RS it nffocts oil rocovory. The vrritors hopo th2t the omosition of available information prosentod in tho rey~ort rill stindate constructive thought and efforts loading torard moro comrlote extraction of oil and gas from resorvoirs.]

Jan 1, 1938