Search Documents

By A. D. Marcy

The Midnite Mine is an inactive, hard-rock uranium mine in Stevens County, WA. Oxidation of sulfide-containing minerals, primarily pyrite, in the ore body produces large quantities of acidic water. An interception system installed by the mining company limits the discharge of contaminated water from the mine. The U.S. Bureau of Indian Affairs (BIA) and the U.S. Bureau of Land Management (BLM) have been actively involved in planning remediation of the disturbed areas. To assist in remediation, the U.S. Bureau of Mines (USBM) initiated research to determine water quality and to define ground water flow characteristics. USBM personnel designed a monitoring network, supervised installation of sampling wells, and collected and analyzed water samples. This Report of Investigations describes interpretation of data collected between December 1989 and April 1992. The computer program WATEQ4F was used to identify aqueous species distribution and to calculate potential solid phase controls of solubility. To assist in interpretation of changes in water quality between sampling locations and to develop models describing proposed flow paths, the computer program BALANCE was used. Using output from these programs and field observations, a description of the chemistry along proposed ground water flow paths at the mine is presented.

Jan 1, 2010

By Maureen M. Foss

Underground coal mining is hazardous due to changing geological conditions. One geophysical method showing promise for in-seam hazard detection is ground-penetrating radar (GPR). The Bureau of Mines recently completed preliminary studies to demonstrate the feasibility of using GPR for in-seam hazard detection. Investigations included air and coal tests for the purpose of checking equipment accuracy, coal penetration, and other factors such as the effects of receiver orientation. Further investigations involved using both a short pulse and a new prototype synthetic-pulse system to locate a clay vein in a coal seam using trans-illumination. Data were gathered on multiple travel paths, and a back projection processing technique was then used to create a tomographic image using the calculated velocities. A computer model of the same coal seam was subsequently processed using the same tomographic tech-nique, and the results were compared with those of the actual data. Analysis of the tomographic images shows the presence of the clay vein, although its boundaries are unclear due to the tomography method used. Results of these preliminary studies show that GPR is feasible for use in in-seam hazard detection and point the direction that future research should take. A need has been shown for research involving more sophisticated tomography techniques, transmission studies on thicker coal seams, and reflection studies using the synthetic-pulse system.

Jan 1, 1987

By John C. Edwards

Standard smoldering and flaming combustion tests using smaIl coal samples have been developed by the U.S. Bureau of Mines as a method to evaluate the response of a smoke detector. The tests are con-ducted using a standard smoke box designed and constructed according to Underwriters Laboratories. The tests provide a standard, easily reproducible smoke characteristic for smoldering and flaming coal combustion, based upon a comparison of the smoke optical density and the response of a standard ionization chamber to the smoke. With these standard tests, the range of threshold limits for the response of a smoke detector and the detector's reliability can be evaluated for nearly identical smoke visibility and smoke physical characteristics. The detector's threshold response limits and reliability need to be well defined prior to the instrument's use as part of a mine fire warning system for improved mine safety.

Jan 1, 2010

By Forrest T. Moyer

In 1969, the number of fatal injuries in the coal mining industry was lower than in any previous year and the number of nonfatal injuries was lower than in any preceding year except 1968. Fatal injuries in 1969 totaled 203 with frequency rates of 0.85 per million man-hours of worktime and 0.36 per million tons of coal These rates were new annual lows. Nonfatal injuries totaled 9,917 with frequency rates of 41.76 per million man-hours and 17.42 per million tons. The severity rate for fatal and nonfatal injuries combined was 7,359 days lost or charged per million man-hours. The average severity was 173 days lost or charged per injury. These statistics represent the injury experience of an average of 133,302 employees per day working an average of 225 days in 5,955 coal mines for a total of 237-5 million man-hours worked and a coal output of 565 2 million tons

Jan 1, 1973

[RESULTS OF THE PRIMARY CONVENTIONAL PERFORMANCE AND COST MODEL OF THE UNIT OPERATIONS OF UNDERGROUND PERCUSSIVE DRILLING AND BLASTING]

Jan 1, 1977

By F. E. Block, T. T. Campbell, D. Z. Hobbs

Several methods were investigated for the preparation of high- purity elemental boron in an attempt to develop a feasible process for producing boron on a large scale . In the work described in this report , the metal was prepared by metering boron trichloride gas into a crucible containing molten metal reductants . It was necessary to remove reaction byproducts by acid and aqueous leaching . Magnesium and sodium were tested as reductants , but best results were achieved using lithium or zinc as reductants . Contaminants originating from the materials of construction were the chief impurities in boron made by this method . Impurities ranged from 0.5 to 5.0 percent . Impure boron ( 85 to 90 percent ) was also prepared by the magnesium reduction of boron trioxide in a thermite - type reaction . This product contained magnesium as the chief contaminant . Impure boron made in this way could be upgraded by fusing with potassium fluoborate or potassium acid fluoride . After acid leaching the fusion cake , a product containing 95 to 97 percent boron was obtained . Analytical techniques for accurate determination of impurities in elemental boron are a major problem , requiring solution before a valid comparison can be made of the quality of boron prepared by these various methods .

Jan 1, 1964

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data oil motor gasolines sold during the minter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular- price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1968-69. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

This is the second of a series of reports on properties of commercial motor fuels made pursuant to a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the Department of the Interior. The first report gave data on motor gasolines sold during the winter of 1935-36.3/ These gasoline surveys report results of inspections, in oil-company laboratories, of samples of gasoline obtained by representatives of oil companies from service-station pumps in marketing areas throughout the country. In the present survey are presented inspection data on 239 samples of regular-price gasoline, 166 samples of premium-price gasoline, and 157 samples of third-grade gasoline, a total of 562 samples collected during the summer of 1936.

Jan 1, 1937

By E. O. Binyon

"INTRODUCTION The Gibellini manganese—zinc-nickel deposits, are in southeastern Eureka County, Nev, T. 15 N., R. 53 E. M.D.B.M. 27.5 miles south of Eureka, the county seat.The partly explored deposits, locally known as the Black Iron or Gibellini property, were examined in May 1944 by an engineer 3/ of the Bureau of Mines, who recommended that the deposits be explored further by means of core drilling. The proposed program called for drilling six diamond—drill holes, or eight if necessary, and for trenching at two places — 200 feet northeast and 280 feet west of the shaft on the main deposit.In 1946 the project was set up, and In July, of that year diamond drilling as started. Six holes were drilled for a total length of 1,198.5 feet. No trenching or other exploratory work as done. Work on the project was stooped. October 30, 1946.OWNERSHIPAccording to county records, the property comprises a group of 13 unpatented lode claims, and ownership is divided among Louis P. Gibellini,Louis P. Gibellini and wife (both of Eureka, Nev.), and the International Smelting & Refining Co., of Salt Lake City, Utah. Five claims of the group - the Black Iron No. 1, Black Hill No. 2, Manganese No. 3, Flat No. 1, and Flat No. 2 - are owned by Gibellini. Three claims - the Black Hill No. 1, Black Iron No. 3, and Manganese No. 4 are owned jointly by Mr. and Mrs. Gibellini, and the International Smelting & Refining Co. owns the remaining five - the Black Iron No. 4 and No. 5, and Black Hill Nos. 4, 7, and. 9."

Jan 1, 1948

By Jeffrey Y. Foley

The Bureau of Mines sampled surface exposures of podiform chromite in the Caribou Mountain-Melozitna ultramafic belt in the Kokrines-Hodzana Highlands, central Alaska. Fieldwork began in 1979 as part of an assessment of the mineral potential of lands adjacent to the trans-Alaska pipeline corridor, for the Bureau of Land Management, and continued through 1981 as a Bureau of Mines investigation. The belt comprises six complexes of which the three closest to the pipeline corridor were investigated. Concentrations of chromite disseminated in dunite host rock make up mineralized intervals ranging in thickness from less than an inch to 5 ft and in grade from 3 to 23 pct chromium. The largest occurrence has an exposed strike length of 80 ft. Bulk surface samples were collected from 10 of these exposures, and beneficiation tests on the samples produced concentrates of metallurgical, refractory, and subindustrial grades. Part I--this report--describes the fieldwork; part II--1C 8916--describes the beneficiation work.

Jan 1, 1983

By Wallace W. Roepke

The Bureau of Mines tested new designs of drag bit cutters with sintered diamond inserts instead of standard tungsten carbide tips. The bits were tested for orthogonal cutting forces, primary dust generation, and incendivity, with a standard plumb-bob type conical cutter (600 included tip angle) as the reference. Preliminary wear and impact-failure testing were also done. The results were mixed. Two new designs had forces similar to those of the reference bit, but one new design had about twice the normal force. This same design had almost twice the specific energy during shallow cutting but generated an equal or slightly lower amount of primary dust than did the reference bit. Incendivity was eliminated for two radial designs. One conical design had ignition only after more than 15 impacts, but the other conical design was incendive. Impact failure occurred, but not so quickly as anticipated. Over 7,500 impacts on a sandstone face, with a total cutting distance of more than 1,981.2 m, only scuffed the leading edge of the sintered diamond cutting face but put hairline cracks in the substrate mounting pad. Additional design and testing are needed to develop an optimum cutter, but prospects look good for this material.

Jan 1, 1983

By D. Harrington

The record of fatalities from mine explosions in the United States during the fiscal years 1934 to 1937 wars the best in the history of the mining industry; that for the fiscal year 1939, however, is not so favorable, since nearly as many men (170) were killed by explosions in 1938 as were killed during all of the previous 4 years (182). In spite of the large increase in fatalities from explosions during 1938, the average for the past 5 year period (70.4) is less than one-half the average (13) of the preceding 5 year period. The reasons for the large increase in the number of explosion fatalities during the 7 past year as compared with the previous 4 year are not entirely clear; it is: evident, however, that in some instances there has been laxity in the enforcement of State minim laws, and also that come of our coal-mining people, including workers and operating officials, have failed to carry out tine known precautionary measures to prevent explosions.

Jan 1, 1939

By M. E. Volin

The tungsten potentialities of the Combination mine were examined by a mining engineer of the Bureau of Mines in 1947. A report based upon his personal knowledge of the mine and the results of the examination contained recommendations for further investigation. This report presents factual data from Bureau of Mines field investigations begun in August 1947 and continued until December 1948, except for a 5-month recess during the first winter. The Combinat.ion mining property of 52 patented claims and 15 patented mill sites is in the Black Pine mining district, Granite County, Mont., 11 miles northwest of Philipsburg. The altitude in the mine vicinity is approximately 6,500 feet.

Jan 1, 1952

By Oliver Bowles

The National Granite Commission at its annual meeting in Norfolk, Va., in January, 1930, passed a resolution requesting the Bureau of Mines to conduct an economic study of the granite industry. In compliance with this request a preliminary review has been made of trends, in, the production and uses of block granite. Some unfavorable conditions, were, thus brought to light and certain suggestions regarding a. more orderly and consistent growth in the industry are herein discussed. The results of the study axe, presented in this report for the earnest consideration of the industry and comments are invited, not only on this report but as to future work that might be accomplished by the Bureau of Mines. The authors desire to acknowledge many helpful suggestions and comments from Paul M. Tyler of the Bureau of twines and from Harris F. Sherman, secretary of the National Building Granite Quarries Association. Miss A. T. Coons of the Bureau of Mines rendered valuable, assistance through her wide knowledge of granite statistics.

Jan 1, 1931

By L. A. Haas

S02 reduction with CO was studied in an integral flow reactor at a nominal flow of 0.5 liter per minute. Reactant gas contained 3 percent SO2, 6 percent CO, and the balance He. SO2 conversion was determined for three different types of catalysts. The first consisted of 16 commercial catalysts used for various chemical syntheses. Only the commercial catalysts which contained transition metals in alumina removed more than 30 percent 80a at temperatures below 510° C. Two other types of catalysts were prepared in the laboratory either by pelletizing equal amounts of powdered alumina and transition metal oxides or by impregnating commercial alumina tablets with transition metal ions. Regardless of preparation techniques, Cr and Fe in alumina were the two best catalysts. The observed results suggest that an intermediate (SCO) is formed by the interaction of surface metal sulfides and carbonyls. Alumina then catalyzes the interaction of SCO with S02 to form the end products (sulfur and carbon dioxide). Over 80 percent S02 was removed at 460° C with 2 grams alumina impregnated with 2.5 percent iron.

Jan 1, 1972

By John A. Ruppert

1. It has been proposed that the addition of enough limestone to an open -hearth s lag to give a CaO-3P2O5 ratio of approximately 2-followed by SiO2 firing in an oxidizing atmosphere under the proper conditions of time and temperature will result in a clinker having a magnetic phase containing a preponderance of Mn, Fe, Al, and Mg as oxides and a nonmagnetic phase consisting for the most part of a phosphorus-containing dicalcium silicate. It has been postulated further that the metal oxide phase can be recovered by fine grinding and magnetic separation. These broad principles have been substantiated by numerous clinkering operations made in an electrically fired studio-type kiln, a batch rotary kiln, and a continuous rotary kiln and by magnetic separations made in a Davis -tube separator and a laboratory-size Jeffrey-Steffensen three -roll continuous separator. 2. Quenching the clinker after firing seems to improve its grindability. Microscopic examination of the ground clinker indicates .that the oxide phase grinds down at a somewhat faster rate than the silicate phase. 3. Very fine grinding is necessary to approach liberation, of the oxide phase from the silicate phase. Grinding to ininus-325-mesh, followed by magnetic separation, gave only a rougher concentrate, which had to be reground before final separation. 4. Although the manganese content of the final concentrate was higher, there was some evidence that manganese recovery was lower from a clinker made from a flush s lag than one made from a mixture of tap and flush slags. A possible explanation is that a clinker made from a mixture of slags has a higher iron content and hence is more magnetic and more easily separated.

Jan 1, 1952

By Guenter F. Lehmann

This report summarizes the results of the development and testing of a prototype monorail suspended bridge conveyor (MBC) system as a method of continuous haulage In underground mining applications. Included are the results of full scale, surface and underground testing of the complete MBC system. Conclusions drawn from these results, together with recommended modifications, supports the viability of the MBC system.

Jan 1, 1988

By Erich K. Bender

This report summarizes work performed under Phase I of USBM Contract No. H0366024, Noise Reduction of Jumbo Mounted Percussive Drills. Four drills -Gardner-Denver D93LAR and DH123 and Ingersoll-Rand 0475 and VL120 models were measured at the two manufacturers? test sites; data are given in terms of characteristic noise and vibration levels. A survey of percussive rock drill users is reported. The rationale for the choice of a demonstration drill, the Gardner-Denver DH123, is given and a desired noise reduction goal is established.

Jan 1, 1976

By Jr. Koch

Statistical methods applied at the Bureau of Mines Denver Mining Research Center to data from metallic ore bodies were used to evaluate lignite reserves from core data and to predict the extent of lignite horizons in some Texas lignite beds. Six lignite seam units were studied using data from 361 drill holes. The data indicate a total of 214.2 million tons of lignite in the area examined, and probable reserves of 113 million tons in an area 2,000 feet beyond the limits established by the drill holes. It was demonstrated that lignite reserves present in lenticular beds could be reliably determined by statistical techniques, and that core drilling could be optimized to maximum information with minimum drill holes. The technique described is applicable to other coal beds.

Jan 1, 1966