Search Documents

By Charles L. Harness

Magnesia (MgO) has a variety of uses, and it has become increasingly important as a war material because of the imperative demand for refractories to line metallurgical furnaces, and because magnesia is used to make the in aircraft and other implements of warfare. Magnesia occurs as an integral part of nearly 60 minerals, but it is extracted commercially from only a .smaller number, of them. The present commercial sources are magnesite, brucite, dolomite, raw sea water, sea water bitterns, and well brines. Magnesia Raw Materials Magnesite magnesium, carbonate MgCO3, theoretically contains 47.8 percent MgO and 52.2 percent CO2. There are two varieties of magnesite, crystalline and cryptocrystalline (dense or amorphous). The latter type, though, not so plentiful as the former, is generally purer. It resembles unglazed write pottery in texture, whereas the crystalline variety is generally dark and granular, though the color may vary. The principal domestic deposits, of crystalline magnesite are near Chewelah, Stevens County, Wash. (which has supplied most of the magnesite mined in the United States), in the Gabbs Valley area of Nevada (near Luning); and in Llano County, Tex. Crypto-crystalline magnesite occurs principally in California. Magnesite occurrences have also been reported in several other States, including New Mexico, New York, New Jersey, Pennsylvania, Massachusetts, Vermont, and Maryland, but these deposits have not been developed commercially.

Jan 1, 1943

By R. M. Becker

As part of the Bureau of Mines program for examining the Nation's iron and titanium resources, magnetic, gravity, and geologic surveys were made to permit an estimate of the extent and magnitude of the Iron Mountain, Colorado, titaniferous magnetite deposit. Gabbro is the dominant rock type of the area. Within the gabbro are lenses of titaniferous magnetite, 5 to 25 feet wide and as much as several hundred feet long. These lenses comprise a zone which has scattered occurrences of magnetite for 2,200 feet. To the west, the gabbro grades into a strip of pyroxenite that in turn borders a large monzonite mass. A wedgelike broadening of the pyroxenite with depth accompanied by little or no increase in the titaniferous magnetite is considered a reasonable interpretation of the field data. The iron deposits appear to be limited and discontinuous.

Jan 1, 1961

By F. W. Lane

Some months ago the Bureau of Mines began research of a fundamental character on sulphur in petroleum. In the course of this work, the usual qualitative test for sulphur in organic compounds1 was applied to certain oils that were believed to contain approximately 0.5 percent sulphur. No sulphur was found, and, as a check on the qualitative test, the oils were subjected to quantitative determination of this element by the oxygen-bomb method.2 The sulphur content of the oils ranged from 0.10 per cent to 0.50 per cent. This experience led to further trial of the qualitative test for organic sulphur, both on the oils mentioned above, and on common sulphur-containing organic substances. No difficulty was experienced in detecting the element in the latter, but with the petroleum oils the test, as usually performed, could not be relied upon to detect less than 0.60 per cent of sulphur consistently. The use of mechanically polished pure sheet copper for the detection of free sulphur, hydrogen sulphide, and perhaps other sulphur compounds has been recommended.3

Jan 1, 1927

By Mark Sheppard

This paper is the second of a series recording the results of tests made at various quarries throughout the United States to determine, (1) the relation between the size gradation of feed to, and product from, primary crushers; (2) the particle shape of crushed product; (3) the differences in gradation and particle shape produced by different tries of primary crushers; and ( 4) the differences in gradation and particle shape caused by crushing different kinds of stone. Primary crushing has received comparatively little attention in the technical literature in spite of tine fact that the design of the whole crushing plant should be correlated to the performance of the primary crusher.

Jan 1, 1938

By R. O. Dannenberg

A metallic displacement process, utilizing easily available steel wool or steel window screen, was devised and successfully used for the recovery of silver from waste photographic fixing solutions. Laboratory and prolonged commercial-scale testing established that the iron filament type unit will efficiently precipitate silver, as a high-grade sludge, from acidic waste photographic fixing solutions ranging in grade from less than 1 to over 10 grams of silver per liter. Data and design information are presented to facilitate the construction and operation of a practical unit of any desired size. A smelting process for recovering pure silver from precipitated sludge containing 27 to 80 percent silver was devised.

Jan 1, 1968

By K. K. Kelley, W. W. Weller

Heat capacity measurements of akermanite ( Ca,MgSiO ) , cordierite (Mg2A14 Sig018 ) , gehlenite ( Ca₂Al₂ SiO ) , and merwinite ( Ca ,MgSiO ) were conducted over the temperature range from 50 ° to 298.15 ° K. The entropies at 298.15 K ( expressed in cal / deg mole ) were evaluated as follows : Akermanite , 50.0 ± 0.5 ; cordierite , 97.3 ± 0.9 ; gehlenite , 47.4 ± 0.4 ; and merwinite , 60.5 ± 0.5 . All four compounds have positive entropies of formation from their constituent oxides at 298.15 ° K ; the values range from 4.6 cal /deg mole for akermanite to 10.1 cal / deg mole for cordierite .

Jan 1, 1963

By E. G. Davis

The Bureau of Mines studied tailings samples from 11 large-scale western copper operations to determine the potential for recovery of rutile and other critical and strategic minerals. Up to 15 pounds per short ton (lb/st) Ti02 was found ion these samples; however, only 9 to 44 pct of the Ti02 was liberated rutile. For one sample, gravity preconcentra-tion, grinding, and flotation recovered 34 pct of the Ti02 in a 54.8-pct-Ti02 concentrate. Over 0.38 Ib/st W was found in some of the tailings sampleso Scheelite was identified as the major W mineral. Nine of the eleven samples contained about 0.02 to 0.18 Ib/st Co. Pyrite was the principal Co-bearing sulfide mineral, with Co contained in about one-fifth of the pyrite grains. Up to 30 pct of the Co was concentrated in a bulk sulfide flotation concentrate.

Jan 1, 1988

By James W. Ballard

The facts are generally accepted that an atmosphere containing large quantities of any dust is objectionable to breathe and that some dusts are more dangerous than others. Therefore, knowledge of the composition of dusts is important in evaluating the hazard entailed on exposure. At present, free silica, of which quartz is the most abundant form, is considered one of the most significant dusts, from the standpoint of pneumoconiosis, and one State5/ has established permissible limits of air dustiness on the basis of the free-silica content of rock. The amount of free silica in materials used for rock dusting also has been limited.6/ Determination of free silica or quartz, therefore, is important.

Jan 1, 1940

By O. C. Blade

The southeastern region of the United States is becoming more important as a petroleum-producing area, and it is receiving increasing attention from oil operators. In 1948 total production of crude oil from six southeastern States - Alabama, Florida, Kentucky, Mississippi, Tennessee, and Virginia - was 55,244,000 barrels, which represents 2.7 percent of the Nation's output during that year. Kentucky and Tennessee have produced crude oil since the early days of the industry, but the remaining four States have had production only few years. Data on annual production of crude petroleum in the six States are given in table 1.

Jan 1, 1950

By A. J. Kraemer

This report on the physical and chemical properties of crude oils of California is one of a series on the producing districts of the United States. It includes a short discussion of results, tabulated data, and individual analyses of California crudes. Analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, and Ventura Counties have been published in Serials 25952 and 26083. The analyses reported in this paper corer samples that were obtained subsequent to the publication of Serials 2535 and 2608. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of samples was facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1927

By R. W. Dougherty

From time to time interest has been evidenced in transporting coal with water in pipe lines. About the year 1895, United States patents broadly covering a method of pumping coal with water through pipelines were granted to W. C. Andrews. His process was used to some extent in pumping anthracite culm and waste back into the worked-out portions of the mines. About 1905, W. T. Donnely was granted patents relating to pumping anthracite silt away from the breakers. From about 1913 until 1924, a British engineer, Gilbert G. Bell, used a short pipeline to convey coal with water from barges on the Thames River to the Hammersmith Electricity Generating Station, London. Minus 5-inch coal was transferred 660 yards through an 8-inch pipe. Some trouble was experienced with fine coal, which tended to plug the line. Bell made several proposals to transport coal by pipeline overland from the Midlands to London, a distance of about 100 miles, but these were never adopted. This survey is concerned mainly with the problems presented by actual pipeline transportation of coal with water. It is assumed that the coal will have been processed to remove most of the abrasive impurities by conventional methods prior to introduction into the line, and that it has been crushed to the required top size. Dewatering at the discharge end of the line is considered part of the conventional cleaning process. There still remain many pump-performance and behavior of water-coal mixture problems that can be solved only by actual performance tests. It is recognized that the distribution of coal to other than very large users is not changed. Large storage areas would be required to supply seasonal markets. Large users, such as power plants and heavy industries, could be supplied by branch lines directly to the point of use, It is also recognized that pipe lines might not be able to carry a full range of sized coal to meet market demands in many areas.

Jan 1, 1951

By S. M. Shelton, F. D. DeVaney, M. M. Fine

Ferrograde manganese ore or its equivalent is essential to the manufacture of every ton of steel produced ; although it is well -known that there are large deposits of low - grade ore in the United States , the production of substantial amounts of ferrograde material from domestic sources presents a problem that becomes more and more critical as the stockpiled ore is depleted through inability to obtain adequate supplies from foreign sources . Consequently, a program of laboratory and pilot - plant investigations designed to solve the problem of obtaining a domestic supply of manganese has been undertaken by the Metallurgical Division, Bureau of Mines . This paper is one of a new series that will include reports of results obtained in the various investigations conducted under the manganese program . The scope of the program and the organization that was set up to direct and supervise the work were discussed in the foreword of the first paper of this series , Report of Investigations 3606 , Manganese Investigations 1. Concentration of Manganese Ores from the Drum Mountain District, Utah, by S. R. Zimmerley, J. D. Vincent , and C. H. Schack . Other reports will be published as the work progresses .

Feb 1, 1942

By L. L. Oden

The purpose of this research was to develop a method to remove copper and tin from the magnetic fraction of incinerated municipal refuse, as recovered by the Bureau of Mines pilot plant in College Park, Md. Copper, present in the scrap in a metallic form bonded to ferrous objects, was amenable to leaching in cupric ammonium carbonate solution. Copper levels in small 5-to 10-lb lots of treated scrap were reduced from the initial level, 0.5 to 0.6 pct, to 0.1 to 0.2 pct. Larger lots of scrap (100 lb) were treated less effectively because of poor contact of solution and scrap. Oxidation in the air or in aerated aqueous solution was applied to liberate tin from the dilute solid solution present on the surface of incinerated tinplate. Shredding of air-oxidized scrap or caustic leaching of scrap oxidized in solution reduced tin levels from the initial 0.25-pct level to about 0.1 pct.

Jan 1, 1973

By S. M. Shelton, R. B. Fisher, M. M. Fine

"INTRODUCTION The Batesville manganese district lies in the southern part of the Ozark region, mostly in Independence County but partly in Sharp, Izard, and Stone Counties of north central Arkansas.Oxides, carbonates, and silicates of manganese are found in the district. 4/ Carbonate ores have been mined from time to time, but the reserves of potentially commercial ore are chiefly black manganese oxide minerals.The district has produced manganese ore for many years. lip to and including 1933, 160,804 long tons of ferruginous manganese ore (10 to 35 percent manganese) and 140,277 long tons of metallurgical ore (35 percent or more manganese) were shipped;./ most of it was wad orThe term ""wad ore,"" used locally to designate the soft, clayey de¬posits of oxide ore, is a partial misnomer. The ores contain a soft, low-specific-gravity mineral of indefinite composition, which can be designated as wad, but coarse and fine particles of psilomelane and hausmannite, with a smaller proportion of braunite, pyrolusite, and indefinite manganese silicates, are also present. Large and small lumps of high-grade, hard manganese oxide minerals are found, frequently embedded in a soft, black matrix of fine particles of manganese oxides mixed with gangue."

Jul 1, 1942

By C. A. Herbert

This paper sets forth the hazards of accumulations of explosive mixtures of methane and air due to inadequate ventilation, the causes of which are discussed as follows: 1. Lack of well-maintained air courses. 2. Air losses due to leaky stoppings, trap doors, and overcasts. 3. Faulty mining methods. 4. Poor supervision. A modified plan of room-and-pillar panel mine development is suggested, which, it is believed, will eliminate many off the hazards of gas accumulations inherent in the present method of mine development. It is also suggested that some water-proofing agent be used on the roof of permanent air-course entries in conjunction with roof bolting to eliminate the detrimental effect of the moisture-laden atmosphere during summer and thus prevent serious roof falls.

Jan 1, 1953

By F. D. Stevenson

A metal diaphragm pressure relay system was constructed to measure vapor pressures of the metal halides, oxyhalides, and other substances at temperatures up to 700° or 800° C. The vapor pressure of arsenic (III) oxide (As2O3) was determined to verify the reliability of the apparatus for such measurements. The data for the liquid AS2 Os (2820 to 4830 C) are represented by the equation, log Pmm = 6.875 - 2,929/T, from which the normal boiling point was calculated to be 461° C. The heat of vaporization calculated from this equation was 13.40 ±0.09 kcal/g mole As4OS and is essentially constant over the interval studied. The melting point of the octahedral arsenic (III) oxide was determined to be 278° C from the inter-section of the solid and liquid vapor pressure curves, A thermal analysis apparatus is also described by which melting and transition temperatures could be checked by a method independent of vapor pressure data. The melting points of the monoclinic and octahedral forms were determined to be 314.4 ±1.4° C and 278 ±5° C, respectively.

Jan 1, 1963

By Joseph D. Davis

The term "fusain" was first adopted from the French by the American geologist J. J. Stevenson in 1911, according to Wheeler, (1),3 who applies it to that portion of coal resembling charcoal, which he treats as one of the four ingredients of banded bituminous coal. The term has since been adopted by American writers. The Germans use it with slightly different spelling - namely, fusit. It is the equivalent of "mother-of-coal" and "mineral charcoal" of the earlier British writers. The English word fusain is also applied to "a crayon of fine charcoal" and is derived from the Latin root fusus. OCCURRENCE OF FUSAIN IN COAL AND ITS RECOGNITION Fusain is fairly widely distributed in coals of all ranks in varying amounts. It is almost always present in very thin sheets between the bedding planes of the banded coal constituents and presents a jet-black silky appearance who n the coal is split away. As fusain has little cohesive power the coal splits readily along the planes where it occurs. Such fusain bands often attain appreciable thickness -- frequently 1/4 to 3/4 inch. -Beet (2) has reported a maximum thickness of 2 inches for fusain partings, and Sinnatt (3) has found it in the form of plates and lumps; one lump taken by him from the Peacock mine weighed 3-3/4 pounds. Bore (4) has found it in coal balls. Sinnatt (3) states that fusain occurs in two forms, "the first a hard compact variety occurring rather rarely, which can not be pulverized by pressure of the fingers the second type is the common substance" -- that is, a very friable, easily pulverized material. The writer has also found the two types of fusain in the same coal bed and has observed that the hard variety contained considerable calcium carbonate, which probably entered the material in situ by infiltration. Sinnatt further remarks that the layers of fusain (soft type) usually contain less moisture than the coal (or lose it more readily on exposure), and when exposed they quickly change to flocculent powder so that the fines of the coal as mined are likely to contain a major proportion of this substance.

Jan 1, 1929

By A. W. Deurbrouck

This Bureau of Mines report describes the preparation characteristics of the significant coalbeds from which samples could be obtained in Upshur County, W. Va. One of the 14 samples collected was of metallurgical quality as received, 6 could be sufficiently upgraded to provide acceptable products, and 7 could not be upgraded to metallurgical quality because of their high sulfur contents.

Jan 1, 1967

By R. V. Ramani, R. L. Grayson, R. L. Frantz, V. A. Marple, W. R. Myers, K. L. Rubow, Mutmansky. J. M., T. J. Stobbe

"An investigation of protocols for research performed from 1953 to 1988 on pneumoconioses (with emphasis on diseases related to coal and silica) was conducted in the Generic Mineral Technology Center for Respirable Dust. In addition, interviews were conducted with prominent U.S. medical researchers, aerosol scientists and engineers in government, industry, and universities to determine dust sources, dust preparation methods, laboratory protocols, and determinant variables related to in vitro and in vivo research and assess the comparability of results.Since the original report on the protocol project, additional research regarding free radical existence in freshly produced dust particles and the shape and contamination of particles generated for research purposes has further heightened scientists' concerns. As indicated by current research, fresher dust particles and those with more angular shapes may have a different level of reactivity in biological systems than do older or more rounded particles. Therefore, research on dust preparation methods for biomedical studies was undertaken and will be outlined here.Results of protocol review and interviews are summarized. Research on size reduction methods and their particle characteristics plus some recommendations concerning dust preparation methods and reporting in biomedical publications are also presented. Recent evidence indicates that these recommendations may be of importance in comparing and interpreting research results."

Nov 1, 1995

By R. Hogg, S. Chander

"INTRODUCTION The behavior of particulate systems in general is determined by the properties of the solid and fluid phases and of the interfaces between them. As particle size is reduced, the inter facial effects become increasingly important until, in colloidal systems, they become completely dominant. Interfacial phenomena are especially important in coal processing for a variety of reasons. Because coal is naturally hydrophobic and its density is low, surface forces begin to dominate over gravity at relatively coarse sizes. Coal is thermodynamically unstable in the presence of air, so that surface oxidation occurs readily leading to important variations in surface properties with time and environment. These effects are further compounded by the inherent heterogeneity of the material.Surface characteristics and properties play a significant role in most aspects of coal processing. Comminution, for example, is a process of creating new surface, while agglomeration involves the reduction of surface area and is usually controlled by surface forces. Both solid-solid and solid-liquid separations are influenced by interracial phenomena, Gravity separations are usually performed in a liquid phase and are affected by the wetting characteristics of the various solids present and by the need to ensure proper dispersion of the individual particles. Froth notation, of course, separates particles on the basis of differences in surface characteristics. Chemical processes such as leaching generally involve interfacial reactions whose rates depend on surface area and may be influenced by electrochemical effects in the electrical double layer at the solid-liquid interface, or by adsorption of reactant and/or product species from solution. Solid-liquid separations and associated processes such as flocculation are strongly dependent on the nature and properties of the solid-liquid interface.In characterizing solid surfaces, it is important to consider first the surface area, since this determines the relative importance of the interfacial effects. The structure and chemical composition of the surface may depend on the distribution of different petrographic constituents and impurities such as finely disseminated mineral matter, on the extent of surface oxidation, and on adsorption from the environment. These, in turn, will generally determine the surface properties which define particle behavior. Since the relationships between structure etc. , and properties are not generally known, it is usually necessary to measure properties such as wettability and electrical charge directly."

Jan 1, 1989