Search Documents

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Arkansas has been given in Report of Investigations 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251 of which this is the tenth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of which deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated. and a table for each half township is given with the discussion covering that area.

Jan 1, 1948

By H. C. Fowler

Hydrogen sulphide associated with the gasps and vapors from certain crude oils now produced in the United States has forced a serious health and safety problem upon the petroleum industry. Although the presence of hydrogen sulphide in or occurring with Mexican crudes has been known for some time, it was not until recently that crude oils which give off poisonous amounts of hydrogen sulphide have been produced to any extent in the United State. The injurious effects of this poisonous gas were first recognized by the refiners along; the Atlantic and Gulf Coasts upon receiving shipments of crude petroleum from Mexico. The problem of combating the hazards of the gases and vapors given off by this petroleum become more important as the use of Mexican crude increased. In 1925, the Bureau of Mines and Public Health Service under cooperative agreement with the American Petroleum Institute, studied the causes rend effects of hydrogen sulphide poisoning. Bureau of Mines Bulletin 2312 is report of this investigation, and although written with special reference to refineries, it nevertheless contains much information that is of value to the producer of petroleum.

Jan 1, 1927

By Thomas J. Peters

The Snowbank study area, which had been proposed as Wilderness, lies about 5 air mi southwest of Cascade, Idaho, and about 60 air mi north of Boise. The eastern boundary of the north-south-elongate study area lies 1-to 2-mi east of Cascade Reservoir; the western boundary is contiguous, in part, with the western boundary of Valley county. The 8,200-acre study area is underlain by Cretaceous granitoid rocks of the Idaho batholith. Three prospects were found in or near the study area during a library and field search. Gold occurs at one 30-ft adit, but the gold-bearing structure appeared too narrow to contain resources. Two other prospects appeared essentially unmineralized. No evidence of geothermal activity was observed. Rock in the area is not potentially useful as dimension stone because it does not split into flat slabs. To be used as aggregate, the rock would require crushing and hauling to distant markets. One of 18 alluvium concentrate (placer) samples contained free gold, worth $1.07 per cubic yard of gravel (at a $350 per oz gold price). No alluvial bars were seen; deposits were too small to contain gold resources or be considered gravel resources.

Jan 1, 1993

By G. W. Birge

Carbonizing properties of the principal coal beds of Butler County, Pa., are described in this report by the Bureau of Mines. Eight samples, representing the Upper Freeport, Lower Freeport, Upper Kittanning, Middle Kittanning, Lower Kittanning, Clarion, and Brookville beds, were carbonized at 900° C. by the Bureau of Mines-American Gas Association (BM-AGA) method. Butler County coals rank as high-volatile A bituminous and are generally characterized by high sulfur content compared with Appalachian coals used for industrial coking. If cleaned, the Brookville and one sample of Upper Freeport coal would be acceptable as the major component of metallurgical coking blends. The other Butler County coals tested would be unsuitable for this purpose because of either excessive sulfur or poor coking properties.

Jan 1, 1962

By E. P. Youngman

The mining law of Chosen, which was made effective April 1, 1916, was promulgated as ordinance 8, December 24, 1915, in accordance with the provisions of articles 1 and 2 of law No. 30 of 1911. The new le repealed the mining law, Fo. 3 of 1906, and the placer mining law, No. of 1906, and in effect annulled all prior mining legislation. An amendment to the mining law of 1916 (by virtue of law No. 30 of 1911) vas. passed December 16, 1918, as ordinence o. 17. The detailed regulations, which were to supplement the law proper, and rich in all probability follow closely the regulations in force in the Empire, were not available. Unless otherwise indicated, references in this paper are to the mining law of 1916.

Mar 1, 1933

By Lloyd Williams

1. The investigation shows that the bed identified as Wilder in this report is the only bed in Overton County that has produced commercial coal and is the only bed in which coal reserves were estimated for this report. Three other coal horizons were recognized but lacked enough data for reserve estimates. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated to be 19 million short tons, as of January 1, 1953. Of this total, 10 million tons represents coal 28 inches and more thick. Areas of the Wilder bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By Alfred R. Powell

In another paper the writer has described an investigation in which the forms of sulphur in coke were determined and described. Coke was found to contain four characteristic forms of sulphur- namely, ferrous sulphide, sulphates, ad- sorbed free sulphur, and sulphur held in solid solution in the carbon. While the coke is still in the oven, only two forms of sulphur are present namely, the ferrous sulphide and the sulphur in solid solution in the carbon. During the quenching, however, the sulphur of the coke is subjected to considerable oxidation, a portion of the ferrous sulphide being oxidized to free sulphur and sulphates, while the solid solution form remains unchanged. The coke, however, loses no sulphur during this process, since the free sulphur which is formed ie retained by the coke in an adsorbed form. Since this oxidation of the ferrous sulphide took place so easily, an inves- tigation was undertaken to determine whether this property could not be taken ad- vantage of in some industrial process for the desulphurization of coke. Although it is true that such a roasting process would not touch the solid-solution form of sul- phur, still the removal of the ferrous sulphide sulphur would undoubtedly benefit the coke from the standpoint of the metallurgist. This improvement in the coke would result not only from the decrease in total sulphur, but also from the large decrease in the ferrous sulphide, which is responsible for the contamination of the iron in the upper part of the blast-furnace. The de sulphurization of coke by roasting in air it a new idea, but dates back to the earliest days of coke manufacture. In 1871, Philipparts published the results of some work done by him on the de sulphurization of coke by air, as well as a review of the results of earlier investigators. In the se earlier experiments, nothing was known of the forms in which the sulphur existed in the coke, while the temperature measurements were only approximate, so that altogether the results were not very conclusive nor complete. The de sulphurisation figures given by the se early investigators generally showed a low efficiency for the process, but some extraordinary results were claimed by certain inventors. In the light of our new knowledge concerning the coke sulphur, it seemed to be important enough to warrant investigation.

Apr 1, 1923

By Erik Bengtsson

Phenol was discovered in coal tar by Runge (1)1/ in 1834 and was isolated (2) in 1841 as pure phenol by distilling the tar, extracting with caustic soda, acidifying the extract, and fractionating the tar acids. Later, o-cresol was isolated (3) through careful fractional distillation of the tar-acid mixture. The m-and p-cresols distilled within a boiling range of about 1.50 c. and had to be separated by other means. Raschig (4) fractionated the tar-acid mixture to obtain pure o-cresol, sulfonated the mixture of m-and p-cresols, and treated the cresol-sulfonic acids with superheated steam at 1200 to 1300 c. to hydrolyze the m-cresol sulfonic acid, the p-isomer was not affected at that temperature. He also attempted to make use of the different crystallizabilities of the m-and p-cresol sulfonic acids (5). When treated with sodium bisulfate and sodium pyro-sulfate at 100° to 110° C. or with sulfuric acid (90/0) at 20° C., only the m-cresol was sulfonated (6). Hoffman-La Roche (7) treated the meta-para mixture with concentrated sulfuric acid at 40° to 100° C., when m-cresol and part of the p-cresol was sulfonated, and precipitated the m-cresol sulfonic add by diluting with water. The same sort of separation may be carried out by means of 80 percent sulfuric acid at 35° C. and 35 mm pressure (8).

Jan 1, 1950

By J. K. Whyatt

Assuring ground control safety in many mining and tunneling projects depends, at least in part, on an understanding of in situ stress conditions that will be encountered. Yet it is rarely practical to conduct more than a very limited number of stress measurements. Stresses along the route of a proposed excavation are typically interpolated from available measurements, often assuming a linear variation of stress with depth (or elevation). However, projects where multiple stress measurements are conducted often report more complex variations of in situ stress, usually in apparent relationship to geologic structures. These structures often include lithologies of contrasting elastic properties. A method is proposed for estimating stresses in these cases by first back-calculating regional loads from available stress measurements and then modeling the distribution of stress throughout the rock mass. The method has been successfully applied to a set of in situ stress measurements from the Coeur d’Alene Mining District of northern Idaho, USA. Results provided new insights into district stress conditions and the distribution of rockburst hazards along mine drifts and between various mines. This success should transfer readily to suitable deep tunneling projects.

By W. N. Marchant

The Bureau of Mines performed chemical research to elaborate details of sulfur chemistry pertaining to the citrate flue gas desulfurization process in which sulfur dioxide (SO2), absorbed (as bisulfite ion) in a buffered sodium citrate solution, is reduced by hydrogen sulfide (H2S) according to the overall reaction 2H2S + HSO3 + H+ ? 3S + 3H20. The rate-limiting step in the process was shown to be the reduction by H2S of thiosulfate (S2031-) that is formed as an intermediate. Pseudo first-order kinetic measurements were made at room temperature to retard the reaction sufficiently that adequate analysis was possible. These measurements showed the rates of the following net processes to be -d [S02]/dt (pH 4.5) = (0.409±0.050)min-1 [S02]; d [S2032-]/dt (pH 4.5) = (0.199±0.017)min-1 [S02]; -d [S2032-]/dt (pH 4.0) = (0.0437±0.0265)min-1 [S2032-]~1; -dH2S/dt (pH 3.9) = (21.6±3.0) mmoles/min-atm [H2S]g1.4, where [H2S]g is the partial pressure of H2S in the gas phase, in atmospheres, and the rate describes the consumption of H2S, in millimoles per minute; d[S]/dt (pH 4.0) = (38.0±3.4)min-1 [H2S]1, where [H2S] is the concentration of H2S in solution. Hydrogen ion consumption during the slow phase of regeneration was shown to occur at (2.1±0.5) times he rate of thiosulfate consumption, which is interpreted as evidence for the following as the rate-limiting reaction: 2H2S + S2032- + 2H+ ? 4S + 3H20 A scheme consisting of five sequential general reactions is proposed to account for sulfur formation.

Jan 1, 1981

By Henry E. Blake

The Bureau of Mines has been engaged in a continuing research effort to develop processes for increasing the recovery and utilization of fluorine from low-grade resources. This current research has shown that over 98 percent of the fluorine in phosphate rock is extracted when the ore is treated with excess phosphoric acid in the presence of water vapor at 150° to 180° C. More than 80 percent of the fluorine can be recovered as fluosilicic acid, which can then be converted to commercially useful hydrogen fluoride or fluorspar by previously developed Bureau processes. Extraction of P205 from the ore was about 98 percent in batch tests and 90 percent in semicyclic tests.

Jan 1, 1974

"U.S. Bureau of Mines Publications and Articles, 1994 with Subject and Author Index Compiled by Office of Public Information U.S. Bureau of Mines (USBM) Department of the InteriorINTRODUCTIONThe U.S. Bureau of Mines (USBM) was established in 1910 to conduct inquiries and scientific and technological investigations on mining and the preparation, treatment, and use of mineral substances; to promote health and safety in the mineral industries; to conserve material resources; to promote economic development; to increase efficiency in the mining, metallurgical, quarrying, and other mineral industries; and to inquire into the economic conditions affecting those industries. The organic act of the Bureau, as amended by Congress and approved February 25, 1913, made it the province and duty of the Bureau of Mines to ""disseminate information concerning these subjects in such manner as will best carry out the purpose of this Act.""In accordance with this directive, USBM reports the findings of its research and investigations in its own series of publications and also in articles that appear in scientific, technical, and trade journals; in proceedings of conventions and seminars; in reference books; and in other non-USBM publications. This edition describes reports and articles published during calendar year 1994. It supplements the 50-year list of Bureau publications issued from July 1, 1910, to January 1, 1960; 1 the 50-year list of articles by Bureau authors published outside the Bureau from July 1, 1910, to January 1, 1960; 2 andthe 5-year lists of publications and articlesfrom January 1, 1960, to December 31, 1964,3from January 1, 1965, to December 31, 1969,4from January 1,1970, to December 31,1974,5from January 1,1975, to December 31,1979,6from January 1,1980, to December 31,1984/and from January 1, 1985, to December 31,1989.8"

May 1, 1995

By Laxman S. Sundae

The Bureau of Mines designed, fabricated, and is using an in-seam tester (1ST) for in situ determination of coal cutting forces. This re-port describes the results of field tests conducted in the Pocahontas No. 3 and Upper Freeport seams to obtain peak and mean cutting forces during coal cutting with several bit geometries, including radial and point attack bits currently used on drum-type machines. Comparisons were also made between new and worn bits, and using data obtained from a Bureau-modified chisel bit. The test results show that longwall plough cutting (horizontal cuts) in bony coal bands (shale) requires >3 times the cutting force for the same cuts in a vertical direction. When no bony coal is present, the cutting forces required to make horizontal and vertical cuts are equal. Worn bits require 4 to 5 times more cutting and normal force than new or undamaged bits. Normal force increased drastically for the worn chisel bit. Peak force encountered in making independent cuts was found to be ~3 times higher than that required to make interactive cuts using a spacing-to-depth-of-cut ratio of 2. Both rake and clearance angles were found to have a significant effect on normal and cutting force.

Jan 1, 1986

By R. C. Diehl

Coal, fly ash, and flue gas samples were analyzed for mercury (Hg) by double gold amalgamation-flameless atomic absorption spectrophotometry. The purpose of the study was to elucidate the fate of the trace mercury in the coal when the coal is burned. Samples were collected from a bench-scale 100-g/hr combustor, a 500-lb/hr combustor, and three coal-burning powerplants. In all cases mercury was found in the fly ash. The amounts ranged from about 9 to about 70 percent of the mercury in the coal that was burned.

Jan 1, 1972

By A. W. Deurbrouck

The Bureau of Mines analyzed 13 samples collected from three Randolph County coalbeds. The Peerless and Sewell bed samples were generally of metallurgical quality as received from the mines or could be easily upgraded. How-ever, the Lower Kittanning coa1bed samples proved to be quite inimical to upgrading to metallurgical quality.

Jan 1, 1966

By G. A. Smyres

The Bureau of Mines conducted laboratory studies to determine the feasibility of chlorine-oxygen leaching for treating low-grade zinc sul-fide flotation concentrates. Recovery of zinc sulfides by flotation from complex fine-grained sulfide ores is substantially higher in low-grade bulk sulfide concentrates than in the high-grade cleaned concen-trates required for smelter feed. However, there is no commercial process in the United States for the treatment of low-grade bulk zinc sul-fide concentrates. Leaching experiments using reactors of 500-mL and I-gal capacity were conducted on a bulk concentrate containing 19.3 pct Zn, 35.6 pct Fe, and 39.4 pct S. The effects of pressure, temperature, and percent solids on extraction were investigated. The chlorine-oxygen leaching procedure showed promise for treating the concentrates. Zinc extractions of 95 pct or more were obtained by leaching at 50 pct solids in the temperature range of 1000 to 1200 C. Zinc extractions by leaching with chlorine followed by oxygen at reactor pressures of 50 to 100 psig were independent of pressure.

Jan 1, 1985

By E. D. Eastman

The basic character of the free energy r data relating to water and the oxides of carbon makes it desirable that the most representative values that can be obtained should be constantly available. The calculations of Lewis and Randall3 retain much of their of original value, but appear to require some modification in the light of more recent work. This paper has been written to incorporate the newer information and to present some estimate of the reliability of the resulting figures. The data upon which the calculations are mainly based are, for these substances, the equilibrium constants of the various reactions involved. The original work relating to these equilibria has, been reviewed and, where possible, weighted to correspond with its probable reliability. The differences in the results of the present from the earlier calculations are partly the consequence of this appraisal and partly of the inclusion of more extensive data, as will be indicated in detail in the succeeding sections.

Jan 1, 1929

By John P. Hager

This study investigated the formation of vapor complexes between aluminum chloride and the chlorides of iron, titanium, and silicon. For the A1-Fe-C1 system the proposed gaseous complex species is Al2Fe2C112(g), which is formed according to the reaction 2A1C13(s) + 2FeCl3(s) = Al2Fe2C112(g) The corresponding free energy expression was determined to be ?G° = 38091.49 - 71.45 ? T 400 < T < 600°K The vapor composition above AlC13 melts contaminated with FeC13 was calculated. In the Al-Ti-CI and Al-Si-Cl systems the proposed vapor complex species are Al2Ti2Cl14(g) and Al2Si2Cl14(g) respectively. Free energy expressions were estimated for the formation of the two complex species. Again, the vapor composition above AlCl3 melts contaiminated with TiCl4 or SiCl4 was determined. The results of this study were compared with previous studies on the three systems.

Jan 1, 1980

By A. L. Engel

This report describes results of laboratory-scale experimental treatment of nine ores containing gold and silver, including samples of products of previous plant treatment, from ore deposits in California and Nevada. The samples treated were taken by engineers of the Bureau of Mines during investigations of these ore deposits. The information reported is of interest for development of the mining districts represented or in future Investigations of similar ores from other sources. The treatment methods were as simple as possible. More complicated treatments were tried when required, The applicability of the methods and their limitations in treating the ores are shown by the data in this report. The following treatment methods were employed in the experiments described: Screen analyses were made to determine distribution of values in various screened-sized portions of crushed ore, or to determine optimum size to which a particular ore should be crushed or ground to liberate values, and some-times to determine residual values in various-sized portions of treated material.

Jan 1, 1961

By Carl R. Peterson

The Rapidex continuous spiral blast tunneling concept uses a spiral blast pattern that provides efficient slabbing action, continuous progression, and partial self-shielding. A lightly shielded tunneling machine using this concept stays at the face to provide continuous drill, load, shoot, and muck functions. Previous phases proved the effectiveness of the blast pattern in the White Pine Shale tested the design features of the shield and developed a remote loading and shooting capability using inductively initiated blasting caps and a pumpable slurry explosive. Phase IV assembled previously used front-end elements (drill, loading components, shield) on a used Joy loader chassis and added a mucking system television monitoring and remote control elements. Remote television monitored loading shooting and mucking were investigated. Difficulty was experienced in locating previously drilled blastholes near the bottom of the heading and even on the face. These holes often had to be considered as lost. Because of hydraulic system deficiencies and overall congestion of machine elements at the face mucking rates obtainable with remote television monitoring were low (on the order of 16 tons per hour). Performance was good enough to indicate improved rates if more space were available and if extreme thoroughness were not required. Because of the serious nature of the lost hole problem, a new explosive loading scheme was given a preliminary evaluation. The new scheme would require the explosive and the detonating charge to be loaded through the drill steel. If the necessary equipment modifications could he made and if safe, efficient operation were assured, the new scheme would alleviate some of the crowding at the face and would eliminate the lost hole problem.

Jan 1, 1978