Search Documents

Table 1.-Salient statistics of carbon black produced from natural gas and liquid hydrocarbons in the United States [ ]

Jan 1, 1967

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By R. G. Sandberg

The Bureau of Mines investigated a hydrometallurgical procedure to recover gold, silver, and byproduct lead from a complex lead-zinc sulfide ore. A ferric chloride (FeCI3) preleach, at 40° C in 6 h, extracted about 50 pct of the zinc and formed insoluble silver and lead chlorides. Subsequent acid thiourea leaching, for 1 to 3 h at 40° C, extracted about 85 pct of the gold and silver. Lead chloride was solubilized from the remaining residue with NaCI brine solution at 55° C in 1 h. Lead metal was recovered from the brine solution in an electrolytic cell with an anion perms elective membrane at a current efficiency of 95 pct and current density of 100 A/m2. Spent FeCl3 leach solution was reoxidized in the anode compartment at a current efficiency between 75 and 95 pct.

Jan 1, 1986

By Michael F. Dunn

Since crushing of rock to a smaller size is an integral part of almost any mining and quarrying operation, a study was carried out to identify and develop improved techniques for alleviating a major cause of accidents and work stoppages arising when an oversize luck or boulder lodges in the throat of the crusher. The configurations and operations of various crusher types is described, sources of boulders in the mining operation, and a detailed review is made of mining, quarrying, and construction regulations for all states, Canada, and the Federal Government for applicable provisions. Representative mines were visited and other operations contacted for their boulder handling techniques where it was found that blasting techniques used included mudcapping, bombs, and blockholing, often done very crudely and inefficiently with poor practices and various mechanical systems were used such is hooks of, overhead cranes, impact hammers, and grapplers. Safety analyses of all methods pointed out the hazards associated with blasting in the open and the dangers of entering a crusher. Boulder blasting can be done in a safer fashion if a planned step-by-step procedure is followed, and inherently safer blasting products such as exploding bridge wire blasting caps and improved blockholing techniques. In general, though, the installation of a suitable mechanical system such as an impact breaker will prove safer and cost effective even in a smaller mine or quarry.

Jan 1, 1981

By G. J. Hundman

Control of respirable dust produced by auger type continuous mining machines is normally attempted by water sprays from fixed nozzles mounted on the frame of the machine. In tests conducted under this contract, a 'wet auger' system was used, where the spray nozzles were mounted on the rotating auger itself. The tests were conducted at the Hunter mine of Smith and Stover Coal Company using a Jeffrey 1.00L auger miner. Operating the mining machine in the wet auger mode, it was found to produce 47 pct less respirable dust than when the fixed conventional sprays were used. On section dust levels were reduced too 3.5 mg/m3 which is equivalent to approximately 2.0 mg/m3 for a full shift portal to portal sample. The major difficulty that had to be overcome was the development of a simple reliable water transfer mechanism to get the water into the rotating augers. This was successfully achieved by the development of a water-through-the-shaft water system. This system can be retrofitted to existing machines and is available in kit form.

Jan 1, 1977

By Almon F. Robertson

"INTRODUCTION AND SUMMARYThis is one of a series of reports describing investigations within the Missouri River Basin in Montana conducted by mining engineers of the Bureau of Mines, Minerals Division, Region II. The primary purpose of these investigations is to provide basic information to agencies of the Department of Interior and others concerned with the planning of power and other water developments in the basin. This report contains only such factual data as have been authorized for public distribution. Special precautions have been taken not to reveal any information or data that are considered confidential.The field investigations for this report were made during the summer of 1949. Virtually all known metallic mineral deposits in the county and same nonmetallic (industrial) mineral deposits were investigated. Most of the mines and prospects have been inactive for many years. The old underground workings generally are only partly accessible; many are entirely inaccessible. Most of the mining claims were located many years ago, and a considerable number were patented. Many claims were abandoned; others were relocated. Nimes and ownerships often have changed. Because of such conditions, much of the information on most of the mines and prospects necessarily has been obtained from available Federal and State publications, private geologists' and engineers' reports, and from owners and local residents.Metal mining in Cascade County, Mont., has been confined mainly to the silver-lead-zinc deposits in the Montana (Neihart) and Barker districts in the southeastern part of the county. The Neihart district has yielded by far the greater part of the county's metal output. The mines generally have been operated intermittently, largely because of fluctuating or low silver and base metal prices."

Feb 1, 1951

By Scott W. Hazen

This report describes the design, analysis, and results of a special experimental mine-sampling project conducted as part of the Bureau of Mines continuing program on sample-methods research. The experimental project was conducted at the Bureau?s Denver Mining Research Center and at the Climax molybdenum mine within the framework of a cooperative research agreement between the Bureau and Climax Molybdenum Co., Division of American Metals-Climax, Inc. The primary objective of the project was to investigate the interrelation-ship between sample volume, number of samples, the standard deviation of an assay distribution, and the precision required for an estimate of grade of ore, and to develop this interrelationship into a relatively simple method of application for use in mine sampling.

Jan 1, 1962

By Homer J. Ballinger

During the fall of 1943 and spring of 1944, the Bureau of Mines investigated nine secondary limonite iron-ore deposits in the Williamsville district of Wayne, Butler, and Ripley counties, Mo., by rotary-bucket and power-auger drilling test pitting, and trenching. Studies on beneficiating the ores were made at Bureau laboratories. Iron ore has been mined in Missouri since 1825, and iron mining reached its greatest development between 1870 and 1890. During this period, production averaged about 250,000 tons annually.

Jan 1, 1948

By Martyn F. Roetter

The objectives of the work described in this report are to determine the communications requirements and need for communications, both for voice and control, on longwalls, and to make recommendations for longwall communications equipment and systems. These recommendations are designed to guide the future development of longwall communications. Information necessary for the accomplishment of this work has been gathered by a series of visits to longwall mines and discussions with longwall mine operators, as well as with suppliers of longwall communications and mining equipment and with Bureau of Mines personnel. In addition, it has proven possible, through personal interviews and literature evaluation, to gain an understanding of the experience and attitudes towards longwall communications in countries where longwall mining is far more widespread than in the U.S., namely the Federal Republic of Germany, the United Kingdom, France and Belgium.

Jan 1, 1976

By G. S. Scott, W. J. Huff, G. W. Jones, R. E. Kennedy

"INTRODUCTION This report gives preliminary results of field and laboratory investigations made at the request of the War Production Board relative to causes that have occurred during the last 8 months in acetylene-generat72,r plants in shipyards on the Pacific coast.Six acetylene-generator explosions have occurred in four shipyards. These explosions killed five operators, injured six others, and extensive damage to the plants involved and curtailmnent of vital defense Although the occurrence of acetyiene-generator explosions in other section of the United States is not known, it appears, at least, that if such have occurred, they have caused only minor damage and no loss of lives.The use of acetylene in shipyards on the west coast has expanded tremendously during the past 2 years. These shipbuilding, companies erected aletylene-generatcr equipment, which was soon found to be entirely inadequate to meet the needs of their expanding acetylene requirements for welding, cutting, shrinking, and other purposes, and instances found it necessary to operate their equipment at rates greater than deemed consistent with safe operating practice."

May 1, 1944

By Fieldner. A. C.

"In preparing this paper, an attempt was made to obtain results of plant-scale carbonization tests on washed and unwashed coal tram to same mine. A letter. in which the following questions were asked, was sent to some 50 coke-oven superintendents and others who might be interested:“What is the influence of washing coal on:(1) The chemical and physical properties of coke, as for example, the size, the amount of breeze, the fracture, strength, cell-structure, etc.(2) The quantity and quality of gas and by-products.(3) The capacity of the ovens.(4) The composition of the coal..""Your general opinion, as well as any specific data or results of testa, on this important subject will be greatly appreciated.""Of the 45 replies received, 24 stated that they had never used washed coal; 11 had used washed coal but had no comparative data on similar coals washed and unwashed; 7 answered some of the questions based on their general experience; and 3 gave some test data on Pittsburgh bed coal from western Pennsylvania. In none of the three tests did the washed coal come from the same mine as the unwashed. The washed coals in the three tests were from the same washery - one of modern construction in which the operations are under careful technical control in order to give a uniform product containing a minimum of surface moisture. The unwashed coals which were previously used in these plants were from different nearby mines in the same coal bed, and were supplied by the same company. Obviously, no sweeping or finale conclusions can be drawn from these few tests on coal from a single washery. Therefore, the writer vas obliged to consult the literature, coal-carbonization and coal-washing engineers, and other authorities to supplement the fragmentary information gleaned from the questionnaires in order to present a picture of chat gas engineers may expect from the use of washed coal in a carbonizing plant."

May 1, 1930

By Karl-Heinz Frohne

This report presents the findings of a study of a portion of the Clover-Rush Run oilfield located in Roane County, W. Va. The study was made to investigate the possibilities of secondary oil recovery in the Big Injun sandstone underlying the William Kaufman lease. Reservoir properties, original reserves, and primary oil recovery are also presented. The investigation is based on a core analysis and related laboratory tests, well records, field production data, and subsurface information from the Kaufman property. A theoretical primary oil recovery of 9.7 percent of original oil in place is predicted for the reservoir. A waterflood performance prediction of a hypothetical pilot area was made by use of a computer. The prediction showed that, based on laboratory oil water relative permeability curves, the water-injection time needed to initiate oil production is excessive and that the stabilized water-injection and corresponding oil-production rates are very low. This precludes waterflooding the reservoir on an economic basis. A prediction for secondary oil recovery by gas injection was attempted but could not be completed because essential reservoir data were not available. In July 1965, the lease operator initiated, and is currently conducting, a gas-injection program, but there had been no increase in oil production up to November 1966.

Jan 1, 1967

By Kenneth M. Smith

The kaolin deposits of Aiken County, South Carolina (fig. 1), have been worked continuously since 1852. It has been long known that the deposits contain a high percentage of' alumina and that large reserves exist. These facts led to the early selection of' this area for examination in the search by the Bureau of Mines for high-alumina clays. An exploratory program was started by the Bureau, and drilling was carried on from. June 27, 1942, to October 31, 1942. The kaolin-bearing district occupies an area approximately 25 miles long and 11 miles wide, running northeast, with its center at Aiken, S. C. (fig. 1). Within this district, a triangular area bounded by Horse Creek, Silver Bluff Road, and Hamburg Road was roughly prospected by boring 43 machine and 12 hand holes. As a result of the data obtained, a final smaller area was chosen for more systematic prospecting. This area is bounded by Pine Log, Tewkesbury, Silver Bluff, and Craig Sawmill Roads and covers about 4,000 acres. Mineral exploration agreements covering 11,272 acres were signed by 35 property owners, and 11,956 feet was drilled in 200 holes on these properties.

Jan 1, 1949

By D. R. Tweeton

The U.S. Bureau of Mines has developed tomographic computer programs for geophysical applications and is distributing them as part of a Bureau plan to facilitate the transfer of technology to potential users. These programs were developed for predicting and monitoring the flow pattern of leach solution during in situ mining. The Bureau has also applied them to assessing high-wall blast damage and examining the integrity of mine-related geological structures. This report describes the curved ray program BOMCMTR (Bureau of Mines curved ray tomographic reconstruction), tells how to run it, and gives examples with synthetic and field data. BOMCRATR provides optional mathematical constraints to counteract the nonuniqueness of tomographic reconstructions with crosshole data. These constraints include limiting the maximum and minimum velocities, fixing the velocity at any point to any value, and establishing layers in which velocity does not vary with horizontal position. The user can test for nonuniqueness by varying the initial velocity pattern, The program can perform either curved or straight ray analysis. Ray paths are calculated analytically in triangular pixels, which is faster than incremental numerical approximations,

Jan 1, 2010

By E. P. Carman

This: report gives data on the installation and operation of a packaged-unit heat-pump installation in a residence in McLean, Va., a suburb of Washington, D. C. The original equipment, installed in January 1947, was one of the first of 50 experimental Marvair units manufactured by the Muncie Gear Works, Inc., Muncie, Ind. The compressor unit of this installation was replaced by the company in September 1947, with a modified commercial model. The commercial unit and the original pump and fan accessories have been used as the sole means of heating (and cooling in summer! the. residence for the subsequent five winters and summers. The conclusions and data given herein, therefore, cover 6 winters sad 6 summers of heat pump operation, including 1 winter when temperatures averaged below normal for 2 months and the following summer when temperatures were above normal.

Jan 1, 1953

By H. M. Harris

The Bureau of Mines investigated chlorination of domestic ilmenites in a fluidized coke bed at temperatures of 950° to 1,150° C. Objectives were to develop an effective process for producing TiC14 suitable for TiO2 pigment and to reduce pollution by collecting and treating waste byproduct chlorides. The reactor for these tests was a 10.2-cm-diam quartz tube heated externally by electrical resistance heaters. It contained coke beds of from 35.6 to 82.5 cm in depth that were fluidized by 13 to 25 l/min of chlorine. Ilmenite concentrate powders were introduced at the bottom of the fluid-bed reactor, using the chlorine gas stream as a carrier. Test results showed that greater than 90 pct of the ilmenite reacted at optimum conditions and recovery of TiC14 ranged from 95 to 99 pct of stoichiometric. A temperature-controlled cyclone was used to remove high-boiling-point chlorides such as MnCl2, MgCl2, and FeCl2, and also collected fine unreacted ilmenite and coke dust. Impure TiC14 and FeC13 were separated by collecting the, iron chloride in a condenser con-trolled at 200° C. Titanium tetrachloride vapor was cleaned by passage-through a salt-column filter followed by condensation in water-cooled and refrigerated condensers. Liquid TiC14 was purified further by well-known industrial methods to meet specifications for pigment-grade chloride. Integrated tests were conducted in which chlorine, produced by dechlorination of FeC13 with oxygen, was recycled and used directly in a fluidized-bed chlorinator.

Jan 1, 1976

By J. S. Coffman

Wyoming is estimated to have more than 700 million tons and Utah more than 2.5 billion tons of +10 percent P2O6 phosphate rock considered to have some future economic potential. In Wyoming, the +24 and +18 percent P205 rock potential resources total nearly 250 and 450 million tons, respectively. In Utah, the +31, +24, and +18 percent rock total approximately 33 million, 222 million, and 2.2 billion tons, respectively. These resources are all located above the local drainage levels and do not include latent resources. All of the mining and beneficiation of phosphate rock in the two States is done by San Francisco Chemical Co. The facilities include open pit mines at Vernal, Utah, and Leefe, Wyo.; an underground mine in the Crawford Mountains, Utah, and beneficiation plants at Leefe and Vernal. One of the principal markets for the phosphate rock is Western Phosphates, Inc., fertilizer plant at Garfield, Utah. Recent exploration and development has been under-taken by different companies in the Southeastern Wind River Range, Sublette Range, and Crawford Mountains. The facilities at Leefe and Vernal are in the process of expansion. Some of the areas of western Wyoming contain vast quantities of phosphate rock in minable units, but, because of their remote location, are classed as latent areas. In these areas, there are estimated to be about 700 million, 2 billion, and 3 billion tons of phosphate rock in the +24, +18, and +10 percent P205 grade classes, respectively. The Snake River Range of Idaho and Wyoming is also estimated to contain roughly 21, 106, 177, and 214 million tons of potential resources in the +31, +24, +18, and +10 grade categories, respectively. This area also contains a large amount of latent rock in the more remote areas.

Jan 1, 1967

By Ernest A. Curth

Statistics For 1956-66 show that mine transportation accidents accounted for 19 percent of fatalities in bituminous coal mines, second only to roof deficiencies as a cause of death. Productivity per man-shift increased from 10.2 tons in 1956 to 18.4 tons in 1966, but the fatalities per million man- hours of exposure also increased from 0.19 to 0.21 during that same period, indicating that transportation hazards still persist. Consequently, the Bureau of Mines reviewed the transportation fatalities that occurred in bituminous coal mines during 1956-66. The data were processed by computer to find what constitute hazardous conditions and unsafe actions as well as to correlate occupation and age of victims, transportation type, and mine production. Environmental factors and equipment defects which create hazards, as well as unsafe actions of personnel, were determined for each type of mine transportation: Track haulage, mobile nonrail haulage, conveyors, hoists, automotive operations, and front -end loaders, and for transfer stations (loading points, slope and shaft bottoms, surface transfers) and railroad yards. Man-trip accidents, a group with a catastrophe potential, also were analyzed. The basic design and operational features of each transportation type were outlined and procedures considered safe in the light of accident experience were suggested. Findings show that unsafe actions of personnel and hazards created by environmental deficiencies or equipment malfunctions contribute equally in causing transportation accidents. Accordingly efforts should be directed toward improving working conditions, equipment maintenance, and education and training of employees. The trend is toward using safer modes of transportation, notably conveyors. More attention should be given to track haulage operation, railroad yards, and nondestructive field testing of materials.

Jan 1, 1971

By W. J. Fene, G. W. Grove

An important activity of the Safety Division of the Bureau of Mines , in its efforts to reduce accidents , is the safety inspection of mines . Inspections are made at the request of the operators and are not connected with the inspections by the various State departments of mines . The operating management is furnished with a confidential report of the results of the Bureau's inspections , with recommendations for elimination of the hazards found . These mine - safety inspections include a study of mining practices , conditions , and equipment and in some cases the sampling and analysis of mine air and coal dust . The Bureau of Mines has no regulatory powers , therefore the recommendations made in these reports are merely suggestions , and operators are not required to adopt them . Mine inspections are a check on safety standards , methods , and practices and are essential to any accident -prevention program . A foreman or superintendent may be sincere in his efforts to operate a mine safely and believe that he has done everything possible to attain this end . However , experience has shown that because of his familiarity with the mine and the consequent " nearness " of its various features many unsafe conditions may be , and in most cases are , overlooked ; an inspector , particularly an outsider who is trained to look for hazards , can point out the unsafe conditions overlooked by the foreman or superintendent . Some companies employ safety engineers who make regular inspections of their mines , report substandard conditions and hazards found , and make recommendations for correcting them . Unless these recommendations are carried out the inspections have little value . In making recommendations , due consideration should be given to the feasibility of carrying them out ; the management may and very often does consider a recommendation impracticable because of the

Mar 1, 1935

By B. W. Haynes

With the national focus on energy, the combustible fraction of urban refuse is being extensively considered as a fuel supplement for coal in the generation of heat and power. The objective of these analytical studies by the Bureau of Mines was to determine the concentration of major, minor, and trace elements in the combustible fractions collected at various locations in the Bureau's urban refuse recycling pilot plant located at College Park, Md. The samples processed through the plant were submitted by various municipalities that are considering resource recovery as an alternative to landfill or other means of disposal. Twenty-five elements were determined in samples from six geographic areas and were compared with element concentrations found in typical coal samples.

Jan 1, 1977