Search Documents

By W. H. Kerns

The Taylor Creek lead-zinc deposit is on Taylor Creek, approximately 1-1/2 miles from tidewater, at the head of Duncan Canal, on the east side of Kupreanof Island, Petersburg district, southeastern Alaska. The property was located in 1903, and a 30-foot discovery cut was put to the west tank of the creek. Very little prospecting end developing has been done since that time. The property was examined by J. C. Roehm, associate mining engineer, Territorial Department of Mines, Juneau, Alaska, in June 1946. From exposure n the creek, a mineralized zone with possible dimensions of 1,700 feet by 1,000 feet was indicated. The general strike was northwest, and the dip was low and variable to the northwest. During September through November 1948, the Bureau of Mines conducted a project on the property. Four diamond-drill holes, totaling 770.5 linear feet, were drilled from the surface and 280 lineal feet of hand trenching done. The mineral deposit was found to occur as patches that appear to be a replacement in dolomitic limestone. The patches of mineralization are small, irregularly shaped, and irregularly distributed. Maps showing the location of the drill holes and trenches, analyses of the cores from the drill holes, and anal lee of the samples from the trenches accompany this report (see, also, appendixes A, B, and C).

Jan 1, 1950

By A. Gene Collins, Cynthia A. Pearson, Cathy J. Waters

The chemistry of selenium and tellurium is discussed , along with a method of preparing a synthetic oilfield brine , an oilfield brine sampling method , and methods for determining selenium and tellurium in complex oilfield brines . Selenium either can be reduced to the elemental form with sulfur dioxide and determined semiquantitatively by color comparison of the red amorphous form or can be converted to selenite and determined quantitatively by reacting it with 3,3 ' - diaminobenzidine and obtaining its spectral absorbance at 420 mu . Tellurium can be reduced to the elemental form with hypophosphorous acid , and the spectral absorbance of its red hydrosol can be measured at 400 mu . Less than 0.05 mg / 1 of selenium and 0.1 mg / 1 of tellurium can be determined by the described methods .

Jan 1, 1964

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By Carl Rampacek, W. A. McKinney

The feasibility of leaching calcareous and siliceous oxidized copper ores by downward percolation with dilute acid was investigated in the laboratory and in a small continuous plant operated by the Federal Bureau of Mines . The crushed ore was leached in deep columns with solutions containing 1 or 5 percent sulfuric acid to dissolve the oxidized copper . Bench - scale laboratory tests on two calcareous ores from the same deposit indicated that a maximum copper extraction , about 72 percent , could be expected from heap leaching a feed as coarse as 1 inch . Laboratory tests on a siliceous ore showed that almost 70 percent of the copper could be extracted by leaching a 1 / 4 - inch feed . The bench - scale tests were supplemented by larger continuous runs wherein the copper was recovered from the leach liquors by precipitation on detinned scrap iron . Leaching the calcareous ore for approximately 10 days recovered 62 percent of the total copper . The sulfuric acid consumption was 9.6 pounds per pound of copper recovered . Treatment of the siliceous ore recovered 62.5 percent of the total copper in a 2.5 - day leach and the acid consumption was 3.7 pounds per pound of copper recovered . Cement copper products that assayed over 71 percent copper were obtained from the leach solutions by precipitation on scrap iron . The bench - scale and continuous tests demonstrated that downward percolation leaching of the calcareous ores was technically feasible but not economically practicable because of high acid consumption by the gangue . Leaching of the siliceous ore was rapid and the acid and water requirements were nominal . The downward percolation leach procedure is simple and requires a minimum of plant equipment .

Jul 1, 1960

By Donald W. Ross

Petroleum oils of widely different grades have long been clarified or decolorized by contact with fuller's earths. More recently, so-called activated clays have also been used for this purpose. Still more recently ouch clays have been used in the form of nodules termed "catalytic pellets." Clays of varied appearance and from different localities possess the desired bleaching qualities, but evaluation of such clays, so useful to the oil industry, has not been simple. Previous methods of identification and evaluation have largely followed procedures of production methods and were not primarily based upon the fundamental properties of the clays. Thus) a false assumption has grown up that) bleaching clays probably have no common properties on which a-method of comparison can be based. Fuller's earths and activated clays have a large absorptive capacity for the color constituents of petroleum and its products decolorizing is accomplished by bringing the oil into intimate contact with the clay and later separating the decolorized oil from the clay with its load of absorbed coloring matter. Former practice in absorbing "color" was to use the clay as granules or In' powdered form. More recent practice is to use clay pellets that are more abrasion-resistant than the granules. The oil is either filtered through a bed of clay, percolation method, or agitated on contact with the clay, contact method. Viscous oils are decolorized at an elevated temperature, so that their viscosity is lowered to the point at which thorough contact with the clay is insured. Nonhumidifying, nonoxidizing gas, such as dry steam or dry nitrogen, is used to seal such hot oil masses from the atmosphere.

Jan 1, 1948

By Ivette E. Torres

World investment 10 all mineral and mining industry sectors is not available. However, partial information available provides some information useful for analysis. Information available in this section covers limited geographic information on investment in the steel industry, limited information for petroleum industry capital spending, and total U.S. foreign investment in comparison to the mineral-related sectors (tables 13, 14, and 15). Annual steel industry investment is available for the European Community, almost all countries within the European Free Trade Association (EFTA), Latin America, and other countries with significant mineral industries, such as Canada, Japan, and the United States. Although information was not available for 1992, data for 1991 indicate that for those countries aforementioned, total investment increased by 8 %. However, investment patterns were very different within the different groups of countries. While the European Community had a net increase of 12 %, dominated by an almost °40 % increase in Germany, EFTA member countries had a 26 % decrease in investment for the same period. Investment in EC countries was almost seven times that of EFT A countries. Japan's investment in the iron and steel industry, by far the largest of those available, almost twice that of the EC and almost four times that of the United States, increased by more than 20 %. In North America, investment in Canada and the United States decreased. Almost all of Latin America decreased investment in the sector. The notable exception was Mexico, with a 60 % increase. Changes in Mexico's investment policies of the recent past, its economic growth, and privatization of its iron and steel industry are some of the reasons for such an increase. The other country covered individually in Latin America, where investment in the iron and steel industry increased, although slightly, was Argentina. This limited information does not allow a comprehensive analysis of global industry trend, which in turn impacts many other mineral commodities, and with the transition in many countries within Europe and Central Eurasia that are now effecting the steel industries of the countries that were members of the U.S.S.R. and its CMEA partners, it is most regrettable that comprehensive and comparable data, both current and historic, on investment in this area are not available.

Jan 1, 1994

By Sidney Katell

This; report, covering the period January 1965 through December 1965, is a continuation of a series that began with the publication of Information Circular 7516 in October 1949. It is the seventh in a series of reports prepared in cooperation with the American Association of Cost Engineers. The abstracted articles are concerned with all phases of cost engineering in the field of chemical and petroleum plants and related subjects. They are from the following sources: 1. American Association of Cost Engineers Bulletin. 2. Bureau of Mines Information Circulars. 3. Bureau of Mines Reports of Investigations. 4. Chemical Engineering. 5. Chemical Engineering Progress. 6. Chemical Week. 7. Coal Age. 8. Coal.3 9. Cost Engineering. 10. Hydrocarbon Processing and Petroleum Refiner. 11. Industrial and Engineering Chemistry. 12. Nucleonics. 13. Oil and Gas Journal. 14. Petroleum Management. 15. World Oil.

Jan 1, 1966

By Thomas W. Camm

In this U.S. Bureau of Mines report, mine and mill cost models are presented to make quick estimates of the cost to develop mineral deposits in the desert region of the Southwest United States. Regression analysis was used to generate capital and operating cost equations for each model in the form Y = AXB, where Y is the cost estimated and X is the assumed daily capacity in short tons. A and B are constants determined by the regression analysis. Each is broken down into 11 subcategories to facilitate escalation of costs for inflation and to increase their versatility in economic evaluation work. This report contains 2 open pit models, 6 underground mine models, 11 mill models, and cost equations for access roads, powerlines, and tailings ponds. In addition, adjustment factors for variation in haulage distances are provided for open pit models and variation in mining depths for underground models.

Jan 1, 1991

By Charles Prasky

The Bureau of Mines investigated the conversion of nonmagnetic iron minerals to magnetic form through reduction Toasting operations. The primary objective was to obtain a concentrate that could be used as a direct shipping material for blast furnace consumption. Crude iron materials from the Steep Rock Lakes, Ontario, area were prepared into a blend of 8 parts siliceous ore, 3 parts pyritic ore, and 1 part tailings. Experimental work included laboratory reduction roasting tests, two continuous 10-day campaigns, and one 12-hour test all in a 34-inch by 36¬-foot rotary kiln. The objective of the project was achieved in producing an iron concentrate containing about 66 percent iron with over 90 percent iron recovery. Desirable operating conditions were developed in the kiln but optimum process variables were not completely established.

Jan 1, 1969

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By W. A. Cole

This report covers the preliminary phase of an investigation of some clays and shales and other materials in North and South Dakota to determine the feasibility of lightweight -aggregate manufacture in the two States. The background of the light - weight -aggregate industry, on a national basis, and results of preliminary laboratory testing of samples of North and South Dakota clays and shales from various localities are presented herein. The countrywide search for lightweight aggregates was necessitated toward the end of the 19th century by the change in building design from thick, heavy, load- bearing walls to a framework of structural steel .beams and columns with thin walls, followed shortly by the use of reinforced concrete and structural concrete as materials for the load-supporting frame. Ordinary concrete, with sand and gravel aggregate, weighs about 150 pounds to the cubic foot. A lighter concrete was needed to relieve the dead load and make it possible to construct higher buildings or add stories to existing buildings.

Jan 1, 1954

By R. M. Santmyers

Except for optical purposes and a few other special uses quartz and quartzite are to a considerable degree interchangeable. This also may be said with respect to pulverized quartz and ground silica sand, which are discussed in a separate paper of this series. All these materials, except perhaps quartz crystals of optical grade, are abundantly available in many parts of the United States. In the form of ordinary crushed stone much of it is sold at $1 a ton or less, and ordinarily

Aug 1, 1931

By William C. McBee

Specialized sulfur concretes were developed by the Federal Bureau of Mines as a result of research for the beneficial utilization of sulfur in construction materials. Materials were developed for use in acid and salt corrosive environments where portland cement concrete has been found to deteriorate. Because the mineral aggregates also come into contact with the corrosive media, concretes were developed utilizing both limestone and quartz aggregates. The sulfur binder used with both aggregates was modified by reaction with 5 pct dicyclopentadiene to improve product durability. Sulfur quartz aggregate concrete was found to have moderately high strength characteristics (6,000 psi compressive) and was extremely resistant to chemical attack by both acid and salt solutions. Sulfur limestone aggregate concrete exhibited very high strength characteristics (9,000 psi compressive) and was extremely resistant to chemical attack of salt solutions. Both types of concretes maintained their strength and integrity after long-term testing in acid and salt solutions and exhibited considerable resistance to damage by the action of freezing and thawing. Potential uses include leach tanks, electrolytic cells, thickeners, bridge decking, industrial flooring, pipe, and tile.

Jan 1, 1979

By Wm. W. Adell

"These hydrocarbons belonging to the same chemical series as methane, having the general formula CnH2n have many chemical properties in common with methane and their addition to a lean gas charges the properties and burning characteristics of the gas in the same general direction although to a different extent. The hydrocarbons of this series do not readily enter into chemical reaction with other substances and therefore are incapable of combining with oxygen or polymerizing in the disturbing system and thus cannot cause gum and room troubles commonly met with in the distribution of manufactured gas.As the number of carbon atoms in the molecule increases, i.e. in proceeding from methane throughout the series, the oxygen requirements for the complete combustion of unit volume of the gases also increases; in other words, the calorific values of these hydrocarbons (as gases) increases from methane. Similarly the specific gravity increases from methane in the same order. In Table 1 are shown some of the physical constants and properties of a few of these hydrocarbons which hive bearing on their use for enriching gas."

Nov 1, 1927

By Eldon K. Stanek

The material presented in this chapter is a review of the work done during the period from June 23, 1972 to June 22, 1973 which was reported in detail in the first annual report for Grant No. 60122088 which was submitted on June 29, 1973. This report has appeared in the National Technical Information Service as bulletin number PB230 972/AS. 1.2 ANALYTICAL PREDICTIONS OF INDUCED VOLTAGES AND CURRENTS The basic building block in this analytical work is the development of an equivalent circuit. The equivalent circuit for the cable depends on all of the distributed parameters of the cable, although the series inductance and resistance are of primary importance. The cable resistances are generally available from handbooks or from cable manufacturers. On the other hand, the cable inductances are not usually available from either handbooks or the manufacturer's published data. Thus, it is useful to present the results of the derivation of the inductance matrix and a few intermediate steps.

Jan 1, 1975

By Harold J. Rose

The economic situation in Switzerland during recent years has resulted in theoretical studies , engineering development work , and many commercial installations of ingenious methods for using energy more efficiently . The purpose of the present investigation was to learn of recent Swiss developments for the more effective use of coal , which comprises 98.9 percent of the romaining known mineral - fuel reserves of the United States .

Jun 1, 1947

By W. L. Heidenreich

This report describes the methods and results of field investigations conducted by the Bureau of Mines between December 1956 and December 1957 on seven deposits of nickel-cobalt-iron-bearing laterite and weathered serpentine near the west coast of Puerto Rico east and south of Mayaguez. These deposits were named, for purposes of identification, Guanajibo, Punta Guanajibo, Las Mesas, north and south deposits of the Rosario Southeast group, and the west and east deposits of the Maricao Southwest group. In addition, the lower 17 miles of the Guanajibo River Valley was tested at widely spaced intervals for possible concentrations of magnetite and chromite in the alluvial sands. The objective of the investigations was to appraise, by drilling and sampling, the two largest deposits--the Guanajibo and Las Mesas. Testing of the smaller deposits was much more restricted. Field investigations consisted of mapping, drilling with power auger, sampling drill-hole sections, and pre-paring samples for chemical analyses, mineralogical studies, and metallurgical tests. The work was financed jointly under a cooperative agreement by the Bureau of Mines and the Economic Development Administration, an agency of the Puerto Rican Commonwealth.

Jan 1, 1959

By Albert L. Toenges

The Grundy coal field is in process of development, and this circular was written to describe the mining methods and practices in use in the mines now being worked in this field. In lieu of man-hour labor data for individual mines a consolidated sheet of mine costs, which includes expenses for labor, material, and power, is given for all mines. The costs are for a working day only, based on average daily production. Because the demand for coal is seasonal, the costs for idle days, which vary at each mine, have not been estimated. Approximate reserves of coal seams have been estimated from data and maps taken from Bulletin XVIII of the Virginia Geological Survey4/.

Jan 1, 1936

By W. W. Adams

The year 1937 was signalized by increased employment in the metal-and nonmetal-mining 4 industry of the United States. Measured by the number of men working, there was a 17-percent gain in employment compared with 1936. In total number of man-hours worked at all mines, the gain was slightly over 18 percent. Hazards connected with mining resulted in more accidents to the workers than in 1936, but the increase in number of accidents caused only a slight rise in the accident rate because of the much larger increase in the number of man-hours worked. In fact, the fatality rate per million man-hours of exposure was lower in 1937 than in 1936, but the rate for nonfatal injuries increased slightly.

Jan 1, 1940

By Rustu S. Kalyoncu

A major goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. In support of this mission, a survey of the state of the art of chemically bonded refractories has been made, covering the scientific literature, government reports, and patents. This review includes research and development results for phosphate, silicate, oxychloride, oxysulfate, and other bonding agents used in refractories manufacture. A significant finding of the review was that references on bonding mechanisms, bond formation kinetics, and other important process parameters and conditions were few and universally vague. As a result, recommendations are made to expand research efforts to investigate the kinetics and mechanisms of reactions in chemically bonded refractories.

Jan 1, 1982