Search Documents

By Robert J. Timkp, James D. Noll, Peter Hall, Robert Haney, Linda McWilliams

Diesel particulate matter (D PM) samples from underground metal/nonmetal mines are collected on quartz fiber filters and measured for carbon content using National Institute for Occupational Safety and Health Method 5040. If size-selective samplers are not used to collect D PM in the presence of car-bonaceous ore dust, both the ore dust and D PM will collect on the quartz filters, causing the carbon attributed to D PM to be artificially high. Because the D PM particle size is much smaller than that of mechanically generated mine dust aerosols, it can be separated from the larger mine dust aerosol by a single-stageimpacto1: The SKC D PM cassette is a single-stage impactor designed to collect only D PM aerosols in the presence of carbonaceous mine ore aerosols, which are commonly found in underground nonmetal mines. Howeve1: there is limited data on how efficiently the SKC D PM cassette can collect D PM in the presence of ore dust. In this study we investigated the ability of the SKC D PM cassette to collect D PM while segregating ore dust from the sample. We found that the SKC D PM cassette accurately collected D PM. In the presence of carbon-based ore aerosols having an average concentration of 8 mg/m3, no ore dust was detected on SKC D PM cassette filters. We did discover a problem: the surface areas of the D PM deposition SKC D PM cassettes, manufactured prior to August 2002were inconsistent. To correct this problem, SKC modified the cassette. The new cassette produced, with 99% confidence, a range of D PM deposit areas between 8.05 and 8.28 cm2, a difference of less than 3%.

By Hillary W. St. Clair

The reduction zone of the iron blast furnace is represented by a mathematical model of the chemical reactions and heat transfer that occurs between gas and solids during the deoxidation of iron oxide. The model consists of a set of equations and an algorithm whereby the equations may be solved to give the temperature and composition of gas and solids at any position in the reaction zone and at any time after a specified initial state. The model is applied to the special case in which ferric oxide is reduced by graphitic carbon and carbon monoxide produced by burning carbon in dry air. The rate of reduction, carbon consumption and maximum temperature are shown as functions of the temperature and rate of flow of the incoming reducing gas and external heat loss. The model of the reduction zone is the essential part of a general mathematical model for simulation of the iron blast furnace. The simulation model will serve as a research tool to be used in conjunction with an experimental or operating furnace. After the simulation model has been correlated with the real furnace, it is proposed that further experimentation be done mostly with the model. The real furnace will then be operated primarily to test and confirm the model.

Jan 1, 1967

By Frederick Bloetscher

An improved parachute-type stopping for changing the course of mine ventilation air during mine emergencies has been developed by Goodyear Aerospace Corporation for The Bureau of Mines. The stopping can be quickly deployed by one man from a single attachment point and provides excellent stopping performance with the flow in the design direction. Adding pin and foam attachments between its skirt and the passage-way surfaces improves its performance with flow in the design direction and maintains the stopping with zero or reverse air flows. Stopping performance results for a range of airway sizes including 7.5 X 10 ft simulated airway with pressure differentials of up to 3.0 inches of water are presented. Predicted performance values for this stopping design for larger passageways are also presented.

Jan 1, 1977

By B. C. Parks

This is the first of a series of reports on the relation between microscopic composition and chemical and physical properties of banded bituminous coals. It describes the relation between microscopic composition and behavior during thermal decomposition of a heterogeneous, high-volatile A bituminous coal from the Chilton bed in West Virginia. The standard free-swelling test was used as a simple means of studying the effect of heat on the coal. Although swelling indexes are not precise indicators of coal behavior in the coke oven and have limited value in caking investigations, they are reliable for predicting expansion of coal in a fuel bed and have practical value in the study of fuels. The swelling test also supplements other useful laboratory tests for determining the plastic and expansion properties of coal.

Jan 1, 1957

By A. Matzick

In its work under the Synthetic Liquid Fuels Program the Bureau of Mines has developed on a 6-ton-a-day-pilot-plant scale a continuous, gravity-feed retort far distilling oil from oil shale. The development work covered by this report was done from January 27, 1950, to January 26, 1952, at the ail-Shale Experiment Station near Rifle, Colo. Over 300 pilot-plant tests were made during the investigation. The basic retort developed has been named the Gas-Combustion retort. In this process, part of the heat for retorting of the shale is generated by burning recycled product gas in a combustion zone within the descending shale bad in the retort. Additional heat is supplied by combustion of the carbonaceous residue remaining in the spent shale after the oil has been distilled. Air for combustion is admitted through an air distributor in the center of the bed at about the mid-point of the retort. Hot gas rising from the combustion zone heats countercurrently the descending raw shale and liberated shale oil by pyrolysis of the shale. After passing through and exchanging heat with the incoming raw shale, the oil is condensed as a fog or mist in the gas, which is withdrawn at the tip of the retort. The cool gas is then piped to an oil-recovery system where the oil is separated from the gas in centrifugal separators or other types of mechanical or electrostatic separators. The hot, spent shale below the combustion zone is cooled by heat exchange with recycle gas, which is a portion of the effluent gas from the oil-recovery system.

Jan 1, 1955

By L. B. Pankratz

Thermodynamic data on the elements and oxides were reviewed, evaluated, and compiled at the Bureau of Mines Albany Research Center. Values for Cp°, S°, H° - H°298, - (G° - H°298)/T, ?HP, ?Gf°, and log K are given in tabular form. Cp°, H° - H°298, ?Hf°, and ?Gf° are also expressed algebraically. Examples of calculations using these data are given.

Jan 1, 1982

By R. A. Cattell

With the surrender of the Japanese Imperial Government as a climax to the capitulation of the German High Command , the main objective of the Petroleum and Natural Gas Division pivoted from war assignments to its main normal functions . One of these functions is to give wide public distribution to valuable technical facts which the Division has obtained through research on petroleum , natural gas , helium , and related subjects . During the war years many engineering data and scientific facts could be released only on a restricted basis as reports to war agencies and others immediately concerned . Moreover , many of the wartime reports contained masses of detailed data that were prepared under stress to meet emergency schedules . For peacetime publication and application , these data must be reviewed , correlated , and rearranged so as to present the essentials in proper form . To illustrate , a wartime report of 50 pages might be resolved into one curve in a composite graph for a peacetime publication . Another factor affecting the orientation of the work of the Division is the broader horizon of research revealed by its war activities . Fundamental research and careful engineering analyses are just as important in time of peace as in time of war; in fact , they should be more important to the forward view , because under peace conditions disrupting influences that distract from the orderly acquisition of knowledge are minimized . Therefore , the concerted effort has been not to " salvage " the results of the war activities , but to evaluate them on the basis of their relative importance in the future economy of the country . Where wartime investigations have pointed to peacetime accomplishments , the effort has been to give the corresponding type of work additional emphasis . This adjustment can not be made hurriedly , but many of the necessary preliminary steps on the new course have been taken ..

Jun 1, 1949

By E. P. Hayes

This report supplements the date contained in Bureau of Mines Information Circular 6156, "Special features of core drilling in the salt beds of Western Texas and New Mexico," by J. S. Wroth. That circular dealt with the drilling of the first 12 of the 24 potash tests made by the U. S. Bureau of Mines in cooperation with the U. S. Geological Survey; this report is concerned with the drilling of the last 12 tests. ACKNOWLEDGMENTS The writer is indebted to R. E. Heithecker, the Bureau of Mines engineer who had charge of the drilling of tests 13 to 17, for his well-prepared records on the drilling of these tests.

Jan 1, 1933

By Dwight L. Sawyer, Roy T. Sorensen

The Bureau of Mines has investigated the recovery of alumina by hydrochloric acid leaching of calcined kaolinitic clay . Bench- scale studies indicated that horizontal belt filtration was a pprraaccttiiccaall method for separating the siliceous residue from aluminum chloride liquor generated in the leaching step . Miniplant -scale continuous testing was performed to evaluate the filter circuits and to compare filtration response of different calcined kaolin feed materials and of different agitatorbaffle designs in the leaching reactors . Soluble alumina recovery with a single filter ranged from 94 pct with minus 10 -mesh feed more than 96 pct with minus 35-mesh or misted feed . Process advantages were confirmed for the calcined misted kaolin feed material prepared by a Bureau-developed misting process . With two filters in series , an overall filtration rate of 100 lb solids /hr.ft - 2 of filter area was attained with a soluble alumina recovery of more than 99 pct . More than 99.5 pct alumina recovery was obtained with a thickener and a two - filter circuit for either the minus 35-mesh or the misted feed . Modifications in leaching reactor design made to decrease particle- toparticle attrition were successful and significantly increased filtration rates and decreased flocculant requirements .

Jan 1, 1965

By Eldon Keith Stanek

This annual report deals with a multi-faceted research effort to increase mine electrical system safety. The project can be broken down into six task areas. Task one deals with the development of tests and instrumentation to perform these test- that are designed to detect incipient faults on mine power systems. This program also encompasses evaluation of the tests and automation of data collection and recording using a microprocessor. Task two concerns the prediction and suppression of mine electrical transients. This program involves digital simulation and suppression hardware evaluation. Task three deals with the reliability and fail safe assessment of various components of the mine electrical system including both the protective system and bulk power system components. Task three deals with theoretical analysis, laboratory testing and in-situ testing in coal mines of power system devices. Task four is an effort to design an optimal mine electrical distribution system. The initial effort is along the lines of refining analytical tools such as the load flow model. Task five is an attempt to optimize the selection of molded case circuit breakers makes or models on the basis of total annual cost. Task six assesses the availability of equipment to satisfy existing federal regulations.

Jan 1, 1977

By D. W. Bridges

Solvent extraction has become important in recent years as a unit process in extractive metallurgy. The flexibility and simplicity of the technique have attracted widespread attention, and numerous papers describing actual and projected metallurgical applications have been published. However, differences in terminology, procedure, objectives, and standards, as reflected in reports by different operators and investigators, have sometimes made appraisals and comparisons difficult. Consequently, a need appeared for n series of basic reports on the subject. This Bureau of Mines Information Circular is the first of such a series. It deals with the status of solvent extraction in metallurgy, as well as with the rudiments and terminology of the unit operation. In analytical chemistry, extraction of molecular species from aqueous media by immiscible organic solvents has been used for many years to separate and determine chemical elements (61).4 Complex chlorides of iron and other metals are readily soluble in ethers and ketones, as are the nitrates of uranium and thorium. Most metals are extractable as complex salts of some organic reagent, such as dithizone, 8-hydroxyquinoline, or cupferron.

Jan 1, 1962

By G. L. Oldright

The Metallurgical Branch of the Bureau of Mines, as a part of its duties under the Organic Act, works to prevent wastes in industry and to disuse inmate information on the fundamentals of metallurgical processes. During the war, the necessity of large production was increasingly emphasized. Such duties necessitate from time to time the study of units of full commercial size, the operation of which is beyond the facilities of the Branch. When developments have reached this stage; work has been continued in cooperative agreements with operating companies that have been willing to contribute the use of their plants and staffs and to allow the publication of the results obtained for the common good of the industry.

Jan 1, 1948

By Walter Kawa

Bureau of Mines research on the hydrogenation of coal has been concerned with developing processes that could be used to supplement the Nation's petroleum and natural gas resources. Motor fuel was produced in a subsidized coal hydrogenation industry in Europe prior to 1945, but the process used is still not economical and other methods of producing liquid and gaseous fuels from coal are being investigated. As an aid to the planning of coal hydrogenation research, a literature survey was made of processes or methods of hydrogenating coal that differ from the subsidized or conventional process. This report contains a bibliography of unconventional methods of hydrogenating coal and a brief discussion of the economics of the conventional method. A general discussion of unconventional methods is included, and the advantages and disadvantages are pointed out where possible. The survey supplements a previous Bureau of Mines survey3 and a comprehensive review published in 1930.4

Jan 1, 1964

By A. A. Berk

The Bureau of Mines devised a test nipple for the field study of corrosion in the condensate-return lines of Federal heating plants. Corrosion surveys, made with this device, showed that the deterioration of the piping was caused principally by carbonic acid in the steam condensate. Corrosion problems were brought under control when the carbonic acid concentration in the condensate was decreased. In many instances, this was effected by decreasing the total carbon dioxide content of the feedwater; in others, the condensate acidity was neutralized with volatile, alkaline chemicals. Filming treatment with octadecylamine, reported successful in controlling return-line corrosion in industry, was much less effective in Federal area-heating plants. Laboratory study by the Bureau disclosed that octadecylamine is unstable in heating systems. Analytical methods were developed for this chemical and its degradation products in heating-plant condensate. Field surveys, in using these methods, confirmed the instability of the filming material. Laboratory tests showed that the degradation products are not useful film formers. Since filming treatment has little effect on condensate corrosivity, the piping was corroded where it was not coated by the treatment chemical.

Jan 1, 1962

By Frank A. Peters

A series of evaluations is being made to determine the relative processing costs of producing metallurgical-grade alumina from low-grade aluminous materials. These evaluations include the estimated operating and capital costs as well as recommendations for additional research and development to improve the processes and to lower their costs. The design for each process is based on published work. The three processes considered in this evaluation are designed to leach alumina as aluminum sulfate from calcined clay with sulfuric acid and to remove the silica residue by filtration. The filtrate from leaching is then purified by one of the following methods: Removal of iron in electrolytic cells using mercury cathodes; removal of iron by chemical precipitation through the formation of an iron-manganese complex; or precipitation of the alumina from an aqueous-ethanol solution, leaving iron in solution. Both the operating and capital costs for these processes are higher than those for the Bayer process. For plants producing 1,000 tons of alumina a day, the estimated operating costs per ton of alumina are: Electrolytic iron-removal process........... $81.35 Chemical iron-.removal process............... 82.08 Ethanol purification process............... 86.17 The investment in mercury is not part of the operating cost since this cost is considered equivalent to catalyst cost which would not be shown. The estimated capital investments for 1,000- ton-per- day plants on a Marshall and Stevens chemical equipment index basis of 240.0 are: Electrolytic iron-removal process...... $116,775,500 Chemical iron-removal process............... 99,418,900 Ethanol purification process................ 94,210,200 These investments include the working capital but not the land for each of the processes. Included in the electrolytic iron-removal process is an investment of $4,859,400 for mercury. Investigation of other methods for removing iron, of the decomposition operation, and of the leaching operation could reduce these costs.

Jan 1, 1963

By K. B. Lindsey

Geologically, the Williston Basin is a large structural depression of sedimentary rock in Montana, North Dakota, and South Dakota and Manitoba and Saskatchewan, Canada. The approximate It-mite of the basin are shown on figure 1; it is roughly circular with a diameter of about 400 miles and contains approximately 120,000 square miles. Although the petroleum potentialities in this area had long been recognized, it had not been vigorously prospected by the petroleum industry because of its geographic location, rigorous winters, depths to possibly productive zones, difficult geological problems, and the fact that more seemingly favorable areas were available for prospecting. With the discovery of oil near Edmonton, Alberta, in the prolific Devonian reefs, an incentive was given to explore for oil in the southeast extension of the same sedimentary trough, the Williston Basin. The Virden field discovery in southwestern Manitoba in January 1951 was a direct result of this southeastward movement. Discovery of this shallow field was followed soon after by discovery of' deep production on the Nesson anticline in North Dakota at Clarence Iverson No. 1 well. North Dakota then became the twenty-seventh petroleum-producing State.

Jan 1, 1954

By D. R. Tesarik

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars), and biaxial stressmeters (to measure stress changes in several support pillars and abutments). Two-and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 2010

By Thomas F. Anderson

(Measurements of stable isotopic variations (sulfur, carbon, and oxygen), supplemented by chemical, mineralogical, and petrographic analyses have been used to investigate the processes responsible for : (1) the incorporation of sulfur in coal, and (2) the (development of permineralized peat zones ("coal balls"). Sulfur isotopic results indicate that there are two principal sources of sulfur in the Pennsylvanian coals from the Illinois Basin: (1) "primary" sulfur assimilated by plants (low-sulfur coals), and (2) "secondary" sulfur produced by reactions involving H2S that was produced by the anaerobic reduction of sulfate in seawater which permeated the peat during post-depositional marine transgressions (the dominant source of sulfur in high-sulfur coals). Sulfur isotopic compositions of low-sulfur coals in Several Tertiary basins of Wyoming are consistent with a plant sulfur source. However, the inverse correlation between content and isotopic composition of sulfur observed in coals from the Powder River Basin suggest some "secondary" additions to these low-sulfur coals. Seveeral Quaternary (freshwater pears which were submerged by sea-Level rises during deglaciation over the past 30 ka have sulfur contents and isotopic compositions similar to high-sulfur coals. Carbon and oxygen isotopic compositions of calcareous coal balls from North America and Europe suggest that (1) the carbonate was derived from variable proportions of oxidized plant matter (typically predominant) and inorganic carbonate, and (2) the carbonate minerals were precipitated from fresh-to-brackish waters. Local geochemical and hydrological conditions were apparently more important than regional depositional environments in controlling the source of carbonate and the development of coal balls.

Jan 1, 1983

By L. C. IlsLey

"The use of trailing cables on cutting machines, loading machines, and similar electrically operated apparatus is recognized as a necessary adjunct to the economical operation of such units. On the other hand, such cables because of their liability to failure from being run over by cars, locomotives, and other track-operated equipment offer one of the greatest hazards - indeed, probably the worst hazard - met with in the operation and maintenance of permissible equipment. Therefore, the Bureau of Mines is seeking ways of making the use of trailing cables less hazardous.Recently the bureau conducted an extensive investigation of both concentric and duplex rubber-sheathed trailing cables at the Pittsburgh Experiment Station. The results of this investigation were published in two reports.3 4In a larger part of portable motor operations in mines a double-conductor cable can be used. The investigation already mentioned indicated that it is feasible to construct a 2-conductor cable that will stand considerable abuse, such as being run over by loaded cars or light-weight locomotives without producing dangerous arcing in the cable either from grounds or short circuits. There are conditions where more than two conductors are necessary, and in such instances it will probably be necessary to use a cable less resistant to this kind of abuse.Schedule 2C, covering the tests of electric motored equipment, was approved February, 1930. This schedule provides for performance tests on trailing cables as follows;Trailing Cable Performance: The following performance test, optional with the manufacturer, is established for determining the suitability of trailing cables for use on permissible equipment. Trailing cables that pass this test will be especially recommended for this service.The cable will be placed across the two rails of a track and a 4-wheeled 7-ton car will be run over it 50 times. The speed of the car shall be approximately 3-1/2 miles per hour and potential shall be applied to the cable during tests. The cable will be shifted in position after each passage of the car thus giving 100 places over which two wheels have passed. To warrant special recommendation of the Bureau, a cable must neither become short-circuited nor grounded either to the rails or wheels in more than 10 per cent of the 100 places.The Bureau of Mines is prepared to conduct tests as outlined in the foregoing paragraphs to determine the suitability of trailing cables for use on permissible equipment. Application for such tests should be made to the Director, Bureau of Mines, Washington, D. C. Each application should be accompanied by a check for $25.00, made payable to the Treasurer of the United States, to cover the expense of conducting the test on a given size and make of cable."

Apr 1, 1930

By Bruce I. Thomas

As a part of the United States Department of the Interior program for developing natural resources in Alaska, the Bureau of Mines studied the tin-bearing gold-placer deposits in the Tofty area of the Hot Springs district in central Alaska. The principal objective of the Bureau's work was to obtain facts about the extent and character of the placer deposits (including tailing) to indicate the economic or strategic tin-production potential of the Tofty "tin belt." A secondary objective was to determine (if possible) the bedrock Source of the cassiterite and other minerals found in the placer deposits. The placer phase of the work was begun in July 1954 and was continued during the 1955 and 1956 field seasons. Extensions to, and connections between, known placer channels were sought by 82 churn-drill holes. The Bureau drilling did not expand the placer deposits beyond the limits established by drift-mining operations and by previous drilling done by private concerns.

Jan 1, 1957