Search Documents

By D. L. Sawyer

The Bureau of Mines studied alumina extraction from uncalcined, kao-linitic clay at temperatures from 1000 to 2500 C using 20-or 27-wt-pct-HCI concentrations and with an acid-to-clay ratio of from 0.8 to 1.4 times stoichiometric. Autogenous digestion pressures ranged from atmospheric pressure to about 900 psia. Extraction of 96 pct of the alumina was obtained by HCI leaching at temperatures and leaching times that varied from 1000 C for 120 h to 2000 C for 15 min. Hydrochloric acid stoichiometry of the reaction A1203'2Si02'2H20 + 6HCI + 2AICl3 + 2Si02 + 5H20 was studied at different temperatures and leaching times in a 750-mL tetrafluoroethylene-polymer-lined autoclave. A combination of high temperature and 20 wt pct excess HCI promoted rapid and almost quantitative extraction of alumina (99 pct in some tests). Additional Bureau data obtained with 35-mL tantalum bombs and leach-ing tests with added fluoride are also provided. At high temperatures, the addition of fluoride did not result in a significant improvement over HCI alone and was deleterious to the filtering properties of the digest residue.

Jan 1, 1985

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network. and 2)development at a set pit digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the models and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated fur their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By G. W. Birge, D. E. Wolfson, J. H. Lynch

Fourteen coal samples representing the Flag , Fire Clay , Whitesburg , Amburgy , Upper Elkhorn No. 3 , Upper Elkhorn No. 2 , Upper Elkhorn No. 1 , and Lower Elkhorn beds in Letcher County , Ky . , were carbonized by the Bureau of Mines - American Gas Association ( BM- AGA ) method , and yields of products and physical properties of cokes were determined . The samples tested were high- volatile A bituminous in rank , with dry , mineral - matter- free fixed - carbon contents ranging from 55.3 to 62.2 percent . Five of the samples , as received , were chemically unsuitable for metallurgical use because of excessive ash and/ or sulfur content . Generally , strength indexes of the cokes were low and all of the coals would require blending with higher rank coal to obtain satisfactory blast furnace fuel .

Jan 1, 1964

According to contemporary psychophysical theory, the relationship between the strength of a perceived sensation (S) and the intensity of a physical stimulus (1) is best expressed by a power relationship.(1) S=kln (1) This psychophysical principle has been applied to many practical problems, including the development of scales or guidelines for effective temperature, loudness, brightness, and ratings of perceived exertion. Based on the results of a number of experiments using a variety of scaling methods and a number of different muscle groups, the pooled estimate of the exponent for muscular effort and force is 1.7.(2) When applying this principle to work situations, it is assumed that individuals are capable and willing to consistently identify a specified level of perceived sensation (S). For manual materials handling tasks, this specified level is usually the maximum acceptable weight or maximum acceptable force. These phrases are defined by the instructions given to the test subject:(3) You are to work on an incentive basis, working as hard as you can without straining yourself or becoming unusually tired, weakened, overheated, or out of breath. If the task involves lifting, the experiment measures the maximum acceptable weight of lift. Similarly, there are maximum acceptable weights for lowering and carrying. Such tests are isoinertial in nature; however, in contrast to the tests described in Chapter 3, they are typically used to test submaximal, repetitive handling capabilities. Data are also available for pushing and pulling. These are reported as maximum acceptable forces and include data for initial as well as sustained pulling or pushing. Why Use Psychophysical Methods? Snook identified several advantages and disadvantages to using psychophysical methods for determining maximum acceptable weights.(4) The advantages include: • Realistic simulation of industrial work (face validity); • Ability to study intermittent tasks (physiological steady state not required); • Results are consistent with the industrial engineering concept of "a fair day's work for a fair day's pay"; • Results are reproducible; and • Results appear to be related to low-back pain (content validity).

Jan 1, 1998

By Lloyd A. Morley

This eight-chapter document is the second volume of a two-volume report that presents a comprehensive outline of coal-mine electrical power systems from theory to practice. Together, the two volumes contain the vital aspects that go into planning and designing a mine power system. Building upon Volume I, the subject of protective equipment and relaying starts Volume II, first as an introduction in Chapter 8, then by a treatment of device selection in Chapter 9. Chapter 10 continues system protection in terms of transients and overvoltages. Chapter 11 describes the design of major power equipment, including power centers, switchhouses, and substations. Solid-state applications in mining are given in Chapter 12, and batteries and battery charging are discussed in Chapter 13. Chapter 14 covers electrical-equipment in hazardous locations of mining operations. The report concludes with Chapter 15, a discussion of electrical maintenance as well as some specific mine electrical problems. Information on surface and underground use is included in all these chapters. An index finishes the documentation and is cross-referenced to both report volumes.

Jan 1, 1982

By Robert M. Busche

[Recent developments in the gasification of coal, both by the Bureau of Mines and American industry, have intensified interest in the thermodynamic and kinetic principles necessary for understanding the reaction mechanism and rates and the physical changes that take place. In the course of a Bureau of Mines study of the kinetics of coal gasification at the Synthetic Liquid Fuels Demonstration Plant, Louisiana, Mo., a bibliography of approximately two references was compiled. They are listed n this publication and refer both to American and foreign sources.]

Jan 1, 1952

Cutter roof failure, a ground control problem that frequently results in massive roof failure, is common in coal mines of the Northern Appala-chian Coal Basin, causing delays in production and posing a safety hazard to mine personnel. The Bureau of Mines is conducting research on the causes of cutter roof failure to gain a basis from which to predict and prevent its occurrence, and to support such roof when failure occurs or is imminent. Research conducted at the Greenwich Collieries North and South Mines, in central Pennsylvania revealed a correlation between the presence of clastic dikes and formation of cutter roof failure. The research con-sisted of in-mine mapping of geologic and deformational features, rock pressure monitoring, core recovery and evaluation, and in situ stress measurement. It was found that roof failure increased in areas where the occurrence of clastic dikes was most frequent, especially where two or more clastic dikes intersect. Staggering of crosscuts prevented the extension of cutters and deterred the occurrence of large falls extending over several break-throughs. In addition, trusses and cribbing were effective in stabilizing clastic dikes and inhibiting the development of cutter roof failure when employed immediately or shortly after mining.

Jan 1, 1987

By A. W. Decora

Gas-liquid chromatography has been applied to separating basic nitrogen compounds, such as pyridines and amines. Close-boiling compounds have been separated by exploiting structural and polarity differences, using selective liquid substrates dispersed on specially prepared solid supports. Development of these special supports was necessary in order to obtain symmetric peaks for basic nitrogen compounds; solution of this problem was important in applying gas-liquid chromatography to the analysis of basic nitrogen compounds found in shale oil. Attempts to analyze shale-oil tar bases by conventional gas-liquid chromatographic techniques, using Chromosorb4/ or Celite 545 as the support for a nonpolar liquid substrate, resulted in asymmetric peaks. These asymmetries were caused by adsorption of sample vapors on the solid support. Symmetric peaks were obtained when strongly polar liquid substrates were used on either Chromosorb or Celite. However, a solid support giving symmetric peaks only with strong polar substrates restricts the choice of substrate, and frequently, desired separations cannot be achieved.

Jan 1, 1961

By Henry Kreisinger, J. F. Barkley

This book is one of a series of publications being issued by the Bureau of Mines for the purpose of disseminating information in regard to the methods by which the fuels in this' country may be used most efficiently. A knowledge of the temperature of the gases in boiler settings and in other commercial apparatus using heat tends to develop improved designs of apparatus and better methods of operation, thus reducing waste of fuel. The following pages present, for the benefit of those designing, operating, and testing such apparatus, information as to the accuracy of temperature measurements made under certain conditions and the corrections that can be safely applied.

Jan 1, 1918

By A. N. Fried

With the growing importance of fluid injection in recent years, the petroleum industry has been investigating and field- testing a variety of new methods designed to modify the physical properties of reservoir oil to improve the efficiency of gas and water injection. These procedures include condensing-gas drive, LPG (liquefied petroleum gas) injection, alcohol-slug process, high-pressure-gas displacement, detergent-solution flooding, and in situ combustion (30, 37).3 A new and different method to increase the effectiveness of gas and water injection has been tested by the Bureau of Mines, Consideration of both fundamental and practical factors that operate to limit the oil recovery attain- able by conventional oil-displacement mechanisms led to the concept of a displacement mechanism called the foam-drive method. This report describes the experimental study that tested this concept in the laboratory.

Jan 1, 1961

By R. B. Anderson

SULFUR poisoning of iron catalysts in the Fischer-Tropsch synthesis was investigated at the Bureau of Mines, because synthesis gas produced from coal contains sulfur compounds. Tests of two typical iron catalysts with synthesis gas containing known concentrations of H2S were made to determine catalyst life as a function of sulfur concentration to ascertain the type of gas purification required. Fixed beds of activated steel turnings and a fused iron oxide catalyst were investigated in sulfur poisoning tests at 21.4 atmospheres with IH2+100 gas containing 6.9, 23, or 69 mg S as H2S per cubic meter (0.3, 1.0, and 3.0 gr per 100 cu. ft.). In tests of reduced catalysts at constant temperatures, more than 80 percent of the activity was lost when 0.5 mg S/g Fe was introduced. Poisoning of nitrided or carbided fused iron oxide catalysts to a given extent required more than twice as much sulfur than for the corresponding reduced catalyst. When the synthesis temperature was increased to compensate for loss in activity, tests of the fused iron oxide catalysts at constant productivity could be continued for 19 to 98 days. The tests were terminated by clogging of the reactor, presumably caused by carbon deposition. One objective of the present work was to determine if synthesis gas, purified by the Bureau of Mines' hot-potassium carbonate process for removing H2S, OOS, and CO2, is suitable for synthesis on iron catalysts. The sulfur content of the gas purified by tills process is in the range of concentrations used in the present work. In constant-productivity tests of nitrided fused iron oxide catalysts with synthesis gas containing 6.9 mg S/m3, catalyst lives are nearly long enough for serious consideration of tills mode of operation. However, factors relating to selectivity and stability of the catalyst indicate that this type of operation is impractical for a commercial process. On this basis additional gas purification, such as iron oxide boxes following a hot potassium carbonate scrubber, is desirable.

Jan 1, 1965

By T. F. Mitchell

During the investigation or the occurrence of manganese deposits in western United States, Bureau of Mines' examining engineers collected samples from four manganese properties in the Death Valley region, California. These were supplemented by samples submitted by owners of two other properties in the same area. Extensive laboratory tests were made to determine the, amenability of the ores to standard ore-dressing concentration methods. A small sample of high-grade oxide manganese ore from the McWhinney property, San Bernardino County, Calif., was submitted by the owner. Although the sample would sinter directly to plus 48 percent manganese grade, it appeared probable that the ore, if mined in quantity, would be lower in grade and would require beneficiation. Therefore, testing was conducted to remove the chief gangue constituent, calcite. The National Resources, Inc., property (also known as the old Owl Hole mine) is in the Owl Hole Springs district, I mile from Owl Hole Springs, San Bernardino County, Calif., near the southwest corner of Death Valley National Monument. The ore deposits occur as small lenses or ,pockets, evidently .replacements in limestone and granite. Laboratory work was done on a representative sample of orb procured by Bureau engineers.

Jan 1, 1949

By J. B. Littlefield

[A rulp has i~c+:r. ilrsi i,nsd Lo O~JPY:L~ e the mid~ol Llf;pin.5cr rll~!-t-.cxny)lin:: apparatus recently c',ov~-lo.pe;t by tL1e '.liro:ul of !dines- For th-is pilryoac, a po?.-iti~rs-nct.i?~. pvrni? t:,.;~t v:i.l.'l. :.-,,- #?,n c-noot'fl ;L flow nc possiY,].c? is dcni?.oYle. Flota.lS:r vnnc\-t:rre 1jl:~l~l: zrt iln~;xtJsY:or (2s thc:; n1lr.t ke tvrned at h ityh spet.d for rT:oot,c, o;?ey,;ltiori., ~nd at hi:,h s~ee(' the c8n:xcity oi' the s-n:r.llest piqt ott:~ir?:zk?e Is too la~-~:c. nir crrn'rle bler! in nt the intn?~, but t,he mm;nt o nor.;: l.o'q7r ir.:,l soon t ire:. the oyernt or, ]

Jan 1, 1938

By J. B. Littlefield

[A rulp has i~c+:r. ilrsi i,nsd Lo O~JPY:L~ e the mid~ol Llf;pin.5cr rll~!-t-.cxny)lin:: apparatus recently c',ov~-lo.pe;t by tL1e '.liro:ul of !dines- For th-is pilryoac, a po?.-iti~rs-nct.i?~. pvrni? t:,.;~t v:i.l.'l. :.-,,- #?,n c-noot'fl ;L flow nc possiY,].c? is dcni?.oYle. Flota.lS:r vnnc\-t:rre 1jl:~l~l: zrt iln~;xtJsY:or (2s thc:; n1lr.t ke tvrned at h ityh spet.d for rT:oot,c, o;?ey,;ltiori., ~nd at hi:,h s~ee(' the c8n:xcity oi' the s-n:r.llest piqt ott:~ir?:zk?e Is too la~-~:c. nir crrn'rle bler! in nt the intn?~, but t,he mm;nt o nor.;: l.o'q7r ir.:,l soon t ire:. the oyernt or]

Jan 1, 1938

There is a saying, ?If it moves, it vibrates.? This is especially true in our modern industrial environments, where workers use powered tools, machinery, vehicles, and heavy equipment. How workers are affected by these elements of the industrial working environment is a concern of health professionals, govern­ments, and scientists around the world. How to adequately assess the effects of human vibration exposure is an equally important issue. The human body comprises a dynamic structure that is living, intelligent, and complex. Consequently, it is not unreasonable to consider that exposing the body to an array of vibration environments would result in outcomes that are not necessarily simple or easily predictable. Sensations caused by vibration may include nausea, annoyance, discomfort or pain, and exhilaration or pleasure. Many factors contribute to the effects of vibration on humans, including the characteristics of the motion and the exposed indi­vidual, the activities of the exposed individual, and various elements of the environment. There have been attempts to summarize the effects of occupational vibration exposures by simply recommending the avoidance of certain frequencies of vibration or by providing a graphical method, i.e., a single curve displaying all human responses to all frequencies. However, such efforts have not withstood the scrutiny of scientific research and analysis. Thus, attendees and participants at this professional gathering now have the rare opportunity to benefit from the technological advances and new scientific research to enhance their understanding of human responses to vibration that suggest more than a simplistic approach. In the tradition of the First American Conference on Human Vibration (1st ACHV) held in Morgantown, WV, June 2006, the 2nd ACHV provides a forum for scientists, engineers, medical doctors, industrial hygienists, and educators to learn and advance research and education in the specialized area of human body vibration. The conference was organized by the Mechanical and Industrial Engineering Department, University of Illinois at Chicago, with support from the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory. As with the first conference, the 2nd ACHV provides the unique opportunity to learn about the current activities of peers and colleagues and to exchange information on topics of interest such as human response, human modeling, experimental design, sensors, new technologies, and epidemiological studies of human responses to hand-transmitted and whole-body vibration. The conference organizers hope that the publication of these conference proceedings continues to foster new research and technological advances to reduce health hazards associated with occupational vibration exposures.

Jun 1, 2009

By L. B. Pankratz

The Bureau of Mines measured heat capacities of alpha and beta spodumene (LiAlSi2O5) and of beta eucryptite (LiAlSiO4) over the temperature range 51° to 298° K. The entropies at 298° K were found to be 30.9 ± 0.2 cal/deg mole for alpha spodumene, 36.9 ± 0.3 cal/deg mole for beta spodumene, and 24.8±0.2 cal/deg mole for beta eucryptite. High-temperature heat content measurements above 298° K were conducted for the same compounds. Measurements were made to 1,150° K for alpha spodumene, 1,600° K for beta spodumene, and 1,470° K for beta eucryptite. Tables of heats and free energies of formation are given from the elements and from the constituent oxides.

Jan 1, 1967

By R. F. Abernethy

Analytical results, including ash fusibility data, are presented by the Bureau of Mines for 10 major constituents in coal ash from 373 samples of commercial U.S. coals. Determinations of Si02, Al2O3, Fe2O3, and P2O5 were made by colorimetric methods, Na2O and K2O by flame photometry, Ti02, CaO, and MgO by a spectrochemical method, and SO3 by a gravimetric method. In bituminous coal ashes the silicon, aluminum, and iron calculated as oxides often make up about 90 percent of the ash.

Jan 1, 1969

By Rolland L. Blake

Petrographic and mineralogical studies were made on unoxidized samples from the Cuyuna and Mesabi districts to study occurrence and properties of the iron phyllosilicate minerals . Examination of 96 thin sections from the thinbedded facies of the main iron - formation of the Cuyuna district indicates that the most abundant minerals are Mn - Mg - siderite , stilpnome lane , and minnesotaite . Reconstitution and recrystallization of minerals has occurred along certain beds , and textures indicate that some minnesotaite apparently formed at expense of stilpnomelane . Three samples of stilpnome lane and one of minnesotaite were concentrated from fracture - fillings within iron- formation . Results of chemical , optical , spectrographic , X- ray diffraction , and differential thermal analyses on these samples are reported . The detection of ammonia in stilpnome lane samples is the first such occurrence reported , and its significance is discussed . New mineral data are presented on greenalite and probable septechamosite from the Mesabi district .

Jan 1, 1964

By S. J. Hussey

Since the discovery in 1935 by Adams and Holmes that certain synthetic resins exhibit ion-exchange properties, many applications of the ion-exchange process have been made. There are two general types of ion-exchange resins. Cation exchange resins adsorb cations from solution, and these in turn may be replaced by other cations adsorbed under certain conditions. 'Anion exchange resins adsorb acids from solution, and the anion of the acid may then be replaced by other anions. It is reported, however, that certain anion exchange resins have a low capacity for anions of weak acids without the necessity of acid adsorption either directly or as an intermediate step. The adsorbed ions may then be removed from the resins by elution with an appropriate solution, and the resin is prepared for the next adsorption cycle by regeneration with another solution. Sometimes one solution, is used to simultaneously perform the functions of elution and regeneration. The first and probably the largest application is in the field of water purification. Other applications have been made in the production of high-quality foods for human consumption, in the recovery of valuable substances from solutions, in the separation or fractionation of electrolytes, and in several other fields, each of which has its specific applications, variations, and possibilities. Ion exchange resins also have been highly useful in perfecting techniques of laboratory analysis and research.4/, 5/, 6/

Jan 1, 1948

By Chris Nelson

Two pieces of European Union (EU) legislation together establish requirements for protection against risks from vibration at work. The vibration directive1 specifies duties of employers to protect workers from risks from exposure to vibration; the machinery directive2, specifies duties of manufacturers and suppliers regarding the safety of machinery marketed in the EU. This paper discusses both directives and the standardisation programmes that support them. It also addresses the implementation of these requirements in Great Britain. Employers’ duties: the vibration directive This directive requires employers to assess and control risks to health and safety arising from hand-arm vibration (HAV) and whole-body vibration (WBV). Member States were required to implement the directive in national legislation by 6 July 2005. Employers are required to eliminate vibration risk at source, or reduced to a minimum. The duties include: assessing risk and exposure; planning and implementing the necessary risk control measures; providing and maintaining suitable work equipment; providing workers with information and training on risks and their control; and monitoring and reviewing the effectiveness of the risk control programme. Daily exposure exceeding a specified action value triggers a requirement for a programme of technical and organisational measures to minimise vibration exposures and the resulting risk, and the provision of health surveillance. Exposures above a specified limit value are prohibited. When conducting their risk assessments, employers are required to “assess and, if necessary, measure” the vibration exposure of workers, for comparison with the action and limit values. Vibration measurement in the workplace is not expected in all cases and the use of vibration information from equipment manufacturers is specifically mentioned. This provides a link with the machinery directive (see below). Manufacturers’ and suppliers’ duties: The machinery directive The machinery directive, first introduced in 1989, is intended to remove barriers to trade. It puts duties on manufacturers and suppliers who place machinery on the European market to design their products to eliminate or reduce risks to health and safety and to warn the user of any residual risks, providing information required for safe use (for example, operator training, maintenance and selection of consumables). There are specific requirements for minimising risk from vibration in the design and construction of the machine and, in the case of hand-held, hand-

Jan 6, 2006