Search Documents

By J. Douglas Causey

In 1984, at the request of the Bureau of Land Management, the Bureau of Mines studied 9,600 acres of the 12,350-acre Antelope Creek Wilderness Study Area (MT-065-266) in order to evaluate its mineral resources. Within this report, these 9,600 acres are referred to as the study area. The Antelope Creek Wilderness Study Area, Phillips County, MT, adjoins the north end of the Charles M. Russell Wildlife Refuge. Considered part of the Missouri River Breaks, the area straddles the edge of a thrust fault zone that has deformed the Mesozoic strata in the west half of the area. Shale, siltstone, and sandstone of Cretaceous Age are exposed in the area. Coal beds averaging 3.0 ft thick occur in the Judith River Formation. About 0.20 million short tons of coal were mined from the Judith River Formation adjacent to the west boundary of the area; no production is known in the study area.

Jan 1, 1986

By B. W. Gandrud

[This report presents the data of one of a series of investigations of the washability of Alabama coals as indicated by float-and-sink tests mode by the Bureau of Fines at the Southern Experiment Station in cooperation with the University of Alabama and Alabama coal producers. The Klandyke mine, operated by the Blocton Mining Co., is about 1 mile eat of Vest Blocton, Bibb County, Ala., floor the southwestern, extremity of the Cahaba coal field. The Bureau of Mines already has published three reports that deal with the, washability of Cahaba coals - one a washability study of the Clark bed at Marvel4/ one on the tabling of fine coal from the Thompson and Woodstock beds5/, and the third a washability study of the Henry Ellen bed at Acmar6/.]

Jan 1, 1939

By R. J. Leary

Iron and steel scrap has accounted for 45 to 50 percent of the metallics used by the steel industry. In an electric furnace which utilizes a 100-percent cold charge consisting of about 99 percent scrap and 1 percent pig iron, sensible heat from molten pig iron is not present as it is when hot metal is charged to open hearths and converters. A study of means for more efficient utilization of iron and steel scrap in steelmaking indicated that the time and fuel requirements to melt scrap were important cost factors, particularly in arc-furnace steelmaking. A process to preheat scrap economically prior to charging into the arc furnace has been developed, utilizing efficiently the heat from combustion of fossil fuels as a substitute for electric-arc heating in the initial stage of arc-furnace steelmaking. Scrap is loaded into a portable vertical cylindrical furnace body that is open at the top and has a perforated dropout door at the bottom. In the heating operation, the furnace body containing scrap is placed upon a hollow base connected to a flue, and then the burner and combustion-chamber unit is lowered on top of the furnace body. The stream of hot-combustion products flows down through the bed of scrap imparting heat to it, and the cooled gases exhaust through the flue. After the heating operation the furnace body containing hot scrap is transported to the arc furnace for charging. Thus, the furnace body serves as a charging bucket for top-charged arc furnaces, enabling this preheating process to be integrated into existing material-handling patterns in many arc-furnace plants.

Jan 1, 1961

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

By Verne E. Hooker

This Bureau of Mines report summarizes the results of modifications in the borehole deformation gage design and subsequent changes in the overcoring techniques. Modifications in the borehole deformation gage have greatly improved the creep characteristics and enhanced the versatility of the gage. In situ field tests in competent rock near St. Cloud, Minn., provided sufficient data to compare the reliability between gages and new techniques in obtaining good engineering estimates of stresses. Near-surface horizontal stresses at the test sites are compressive and biaxial in nature.

Jan 1, 1974

Geophysical Abstracts 1 - 86 were issued in mimeographed form by the Bureau of Mines; Abstracts 87 - 111 were published in bulletins of the Geological Survey; Abstracts 112 - 116 were issued in mimeographed form by the Bureau of Mines as Information Circulars 7256, 7257, 7267, 7273 and 7285. 1. GRAVITATIONAL METHODS 7380. Dryden, H. L. A reexamination of the Potsdam Absolute Determination of Gravity. Jour. Research Nat. Bureau of Standards, vol. 29, No. 5, 1942, pp. 303-314.

Jan 1, 1944

By Stanley K. Haines

This Bureau of Mines publication comprises 19 tables of data concerning domestic barite production and consumption, imports, and world production for the years 1880 to 1976. Barite is vital to the petroleum industry, with 90 percent of domestic consumption used in drilling muds. Domestic production has traditionally fallen short of consumption: in 1976, 41 percent of the 2.2 million tons consumed was imported. World production of barite increased from 269,000 tons in 1923 to 5.2 million tons in 1975 but is in danger of falling short of future demand. The compiled data provide a comprehensive base of information.

Jan 1, 1978

[ ]

Jan 1, 1979

By N. A. Pace

This is one of a series of papers being published by the Federal Bureau of Mines for the dissemination of information on methods and practices used in the mining and preparation of crushed stone for market requirements. Performance in terms of units of work or tons produced per machine and per operator man-hour are given whenever that information is available. Direct operating costs are useful for comparing different methods, and are, therefore, included if possible. In addition to the factual description of equipment and methods used, it is desirable to discuss the engineering reasons for the choices that have been made. This paper is particularly concerned with the opertions at the Columbia plant of Palmetto Quarries Co. of Columbia, S.C. The plant is about one-half mile east of the Congaree River and adjacent to the southwest corner of the city of Columbia. Rail access is by the Atlantic Coast Line Railroad, and by a spur strack of the Seaboard Airline Railroad.

Jan 1, 1962

By Walter L. Finlay

The Bureau of Mines has developed prototype instruments promising to improve the ability to warn of imminent roof falls. An unusually good opportunity to test these comparatively under natural caving conditions was afforded by the forecasted caving in August 1977 of a mined-out region of the White Pine Mine. The latter's rock strata closely resemble those in many coal mines. The anticipated cave was of the competent-roof/weak-pillar type. It occurred as, and when, predicted. Automated convergence and bed separation gages agreed well with the standard manual convergence gage measurements. A micro seismic gage was found to be insensitive to the fall and may require different test conditions for effectiveness. A roof resistivity unit was tested under a separate Bureau of Mines contract. (No. H02720J7). An unplanned addition showed interesting potential.

Jan 1, 1978

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By Terry S. Cory

This report describes the results of a measurement and analysis program to characterize wireless radio transmission In metal/non-metal mines over a wide frequency range from 0.2 -1000 MHz and over a variety of mine environments. Six mines were chosen based on the relative economic significance of their product to the U.S. economy. Mine types Include 01 f shale, uranium, potash, lead/zinc, copper, and silver. Particular mines were chosen so that the group would embody the most Important mining techniques. The results show that transmission at medium frequencies are optimum tor wireless mine communications, In agreement with extensive testing previously performed by the authors in coal mines, and that mine-wide wireless systems are feasible with a minimum requirement for new dedicated wiring. At least one need for such a wireless system was identified in each mine visited.

Jan 1, 1981

By Curtis H. Elder

In studies conducted by the Bureau of Mines, two test areas were hydraulically stimulated and exposed by mining: One in the Pittsburgh coalbed at the Vesta No. 5 mine, Washington County, Pa.; and one in the Illinois No. 6 coalbed at the Inland mine, Jefferson County, Ill. Induced fractures were contained totally within the coalbed with no adverse effect on the stability of associated rock strata. Induced fractures were vertical and were propagated normal to the direction of least residual tectonic stress. Gas production was increased fivefold to twentyfold by hydraulic stimulation.

Jan 1, 1977

By James J. Dowd

The investigation to evaluate the reserves of coking coal in the United States suitable for the manufacture of metallurgical coke is being made by the Bureau of Mines in three parts: (1) To estimate known (measured plus indicated) recoverable reserves of all coking coal; (2) to upgrade marginal coals through effective preparation; and (3) to study the carbonizing properties of coals and coal blends not now widely used for metallurgical coke making. This is the sixth of a series of reports giving the results of studies by counties under part (1) of the investigation. (See appendix.) This report covers Fayette County, Pa., which comprises the Uniontown and parts of the Brownsville, Connellsville, Donegal, Waynesburg, Masontown, and Confluence, Pa., Morgantown and Bruceton, W. Va., and Accident, Md., quadrangles. (See fig. 1.) A short resume of the chemical and carbonizing properties of the coals ar.9 included. Data on the coal beds in this county were obtained from mining companies, land companies, individual landowners, and other sources of authentic information.

Jan 1, 1951

By W. W. Adams

"The fifth annual National Safety Competition conducted by the United States Bureau of Mines to determine the best safety records at mines and quarries during the calendar year 1929 has been concluded, and the general results of the contest are presented herewith. To the winner in each of the five groups into which the contestants were divided there has been awarded the bronze trophy 'Sentinels of. Safety,' donated by the Explosives Engineer magazine. The trophy for bituminous coal mines was won by a mine in Alabama; that for metal mines by an iron-ore mine in Michigan; that for nonmetallic mineral mines by a salt mine in New York; that for quarries and open-cut mines went to a limestone quarry in Michigan;. the trophy provided for anthracite mines was, of course, won by a mine in Pennsylvania, as all of the anthracite mines participating in the contest are situated in that State.Winners of the trophies were selected by a committee of sward in accordance with rules governing the contest and on the basis of accident records furnished by the various companies to the Bureau of Mines. These records were summarized by the bureau and the results submitted to the committee. Members of the committee are W. H. Cameron, managing director of the National Safety Council. William Green, president of the American Federation of Labor; James F. Callbreath, secretary of the American Mining Congress; T. T. Read, Vinton professor of mining of Columbia University and editor of 'Mining and Metallurgy'; C. B. Huntress, executive secretary of the National Coal Association; A. J., Curtis, assistant to the general manager of the Portland Cement Association; A. T. Goldbeck, director of the engineering bureau of the National Crushed Stone Association.Thirty-four States were represented in the l29 contest. Among the plants which participated were 68 bituminous coal mines, 29 anthracite mines, 54 metal mines, 19 nonmetallic mineral mines, all of the foregoing being underground mines, and 141 quarries or open-cut mines. A total of 106,533,006 man-hours of work was reported by all of the companies. Accidents during the year numbered 7,008 and represented a period of disability equal to 986,306 man-days. Hence the accident-severity rate for all plants combined represented 9.3 man-days of disability for each thousand man-hours of exposure to hazard. Similarly, the combined accident-frequency rate for all plants showed that 66.3 accidents occurred for every million man-hours of exposure to hazard. Both of these rates indicated an improvement over the combined rates for all plants in the previous year's contest. The reduction in the accident-severity rate centered chiefly in the metal mine group, though all except the quarry and open-cut mine group shared in the reduction; the improvement in the accident-frequency rate was in all croups except anthracite and metal, the rate for the former having increased while that of the latter remained unchanged."

May 1, 1930

By G. F. Skala

Additional testing of two prototype instruments for the discrete detec­tion of submicrometer particles in metal and nonmetal underground mines is described. The detectors are designed to utilize properties of submicrometer particles to distinguish between those produced by fires from mine ambient particles primarily resulting from diesel engine exhaust. One instrument is based on the ability to pyrolyze fire produced parti­cles, but not diesel exhaust particles. An alarm is produced when the ratio of pyrolyzed to unpyrolyzed particles exceeds a preset value. The other detector utilizes a continuous flow ion chamber preceded by a denuder to remove charged particles. Discrimination against diesel produced submicrometer particles results because the diesel particles are naturally more highly charged than fire produced particles. In-mine testing was conducted over a period of several months. Both in­struments exhibited an ability to discriminate against diesel exhaust. However, problems with the recording equipment, and with the instruments themselves, due to large ambient dust particles, prevented enough data from being obtained to choose between the two methods. Recommendations to correct the problems are made.

Jan 1, 1982

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the .Oklahoma Planning and Resources Board of the Conservation Commission has been authorized4/ to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

The Federal Coal Mine Health and Safety Act of 1969 limits to 2 milligrams per cubic meter (for dust containing a maximum of 5% quartz) the average respirable dust concentration to which individual miners may be exposed. Section 205 of the Act directs that an appropriate exposure formula for dusts with quartz content in excess of 5% be established. This formula, entered in F. R. Document 70-12351 filed September 16, 1970, is 10 milligrams per cubic meter divided by % quartz. Thus, the total respirable dust exposure permitted limits the quartz to a maximum of 100 micrograms. For example, if % quartz is 5%, 10 mg/5 = 2 milligrams, and (.05) (2 mg) = 100 micrograms. Similarly, if % quartz is 10%, 10/10 = 1, and (.10) (1 mg) = 100 micrograms, etc. If the % quartz is less than 5%, the 2 mg/M3 limit prevails.

Jan 1, 1974

This Bureau of Mines report concerns two subjects important in the application of electric power in mining systems. Electrical transients and their suppression are discussed, and several considerations are explored with regard to the use of explosionproof or other electrical enclosures.

Jan 1, 1979

By D. Harry Chambers

The Bureau of Mines, through a memorandum of agreement with the Department of Defense, conducted research to recover silver from aircraft scrap. Silver was recovered by an electrolytic method from stainless steel honeycomb sections separated from the aircraft. These sections had been constructed by sandwiching a stainless steel honeycomb core between stainless steel sheets and then brazing the assembly with a silver alloy. Over 300 pounds of silver was used in the B-58 bomber, concentrated in certain honeycomb sections of the aircraft. Following shredding of the aircraft parts, an average of 95 percent (ranging 67 to 100 percent) of the silver was recovered in a single electro-refining step. After the electrorefined product was magnetically cleaned, purity of the recovered silver was greater than 99.3 percent.

Jan 1, 1980