Search Documents

By Robert Hopler

RBH Note: in 1913 black powder was still dominant as a coal-mining explosive, but permissible explosives were making some slight headway. For example, in 1902 there were only 11,300 pounds of permissibles used in coal mining, but in 1913 the quantity was 21,801,285 pounds. However, there were 187,551,653 pounds of black powder used that year. It took many years before the use of black powder ended in coal mining. From the picture of the miner reparing his explosives it’s hard to tell what he’s using, but the fact that a wooden Du Pont powder box is shown, he’s probably not using black powder. That doesn’t mean he’s using a permissible, either, since that was not yet a requirement. It’s interesting that the miners have open flame cap lamps, and the miner is actually smoking a pipe while preparing his explosives.

Jan 1, 2014

By E. Contestabile, B. von Rosen, P. Lightfoot

As part of an accident investigation ANFO was subjected to various abusive tests. A tractor-trailer carrying 18,000 kg of blasting explosives, caught fire, burned for approximately 30 minutes, and then detonated. A series of tests was designed to observe the behaviour of ANFO when subjected to different thermal stimulus tests and more specifically, the Height-to-Detonation Test. Three diameters of steel pipes were used in the Height-to-Detonation Tests thereby simulating cylindrical columns within a pile of ANFO. The ANFO samples were then subjected to various thermal stimuli to initiate a reaction. Through the use of some instrumentation, the response of large ANFO samples was recorded and its behaviour, including the occurrence of phase changes will be analysed.

Jan 1, 2001

By Hans-Peter Rossmanith

Fracture mechanics (Atkinson 1987, Broek 1988, Rossmanith 1978-2002, 1983, 1997, Kanninen & Popelar 1985) and wave propagation (Graf 1975, Rinehart 1975) form the main ingredients in the new electronic detonator based blasting technology. The full potential of using short delay initiation timing in bench and underground blasting can only be exploited if the underlying physical processes are properly understood. From a structural geology point of view, in many open pit mine operations, blasting is performed in incompetent and/or loose rock. Under such conditions the stress waves produced by blasting very quickly dissipate in the rock mass and often their energy cannot effectively be put to work. This contribution shows the effect of open and closed joints – and to some degree also faulting – on the blast wave field and shows the influence of structural geology on the blasting result. A simple engineering method which combines wave propagation and impact mechanics is developed in order to assist the non-scientifically trained blaster in understanding blasting in blocky rock formations. Extensive use will be made of the so-called Lagrange diagram which was introduced in detail in the author’s previous lecture at ISEE 2003 (Rossmanith 2003). This presentation can be considered a continuation of the 2003 presentation.

Jan 1, 2004

By Gordon C. Petersen, Gary A. Almeraris

This paper describes the controlled blasting techniques required to mine a rock tunnel section of a main interceptor located in the Boston Metropolitan area. The 3m (10 ft) x 2.8m (9.25 ft) horseshoe shaped tunnel was driven 490m (1600 ft) by conventional drill and blast methods. The geology varied round by round and consisted of five highly faulted and jointed igneous rock types. The tunnel intersected numerous slickenslides and open mud seams which hampered both drilling and loading operations. Smooth blasting wee critical in order to keep overbreak tc a minimum in this extremely hard but blocky ground.

Jan 1, 1991

By Thomas E. Ricketts

Limited void volume blasting (LVVB) occurs when rock is blasted into a volume that is not sufficient to let the rock expand to its free-bulking value. The freebulking value is obtained when the rock particles have enough space to separate, tumble and rotate to produce the maximum amount of void possible between the fragments when they finally come to rest. Although bulking value depends on particle size distribution and shape, a typical free-bulking value for uniform, finely broken shale is about 1.67. LVVB occurs in almost every type of blasting used in both surface and underground mining operations. For example, in multiple-row bench blasting for surface mining, the final delays that are designed to fragment the rock furthest from the free-face are generally confined by previously blasted rock which results in a LVVB situation. In underground mining, the blasting is automatically confined and is commonly done intentionally to limited void volume to reduce mining cost and improve safety. LVVB primarily affects rubble bulking and thus the excavation of the broken rock which is related to the productivity and economics of a mining operation.

Jan 1, 1989

By Samir Garcia, Alain Mestanza

This technical work was carried out in an open pit copper mining unit, located in central Peru, which has a daily production of 440 thousand tons per day. Currently the pit consists of three mining phases, however, in phase 05 north, there is the construction of a shaft with a height of 375 meters, the function of this structure is to collect and drain the water coming from the pit, there is the importance of preserving its stability and keeping it operational, guaranteeing the sustainability of the operation. For this, a controlled blasting plan was developed that goes from level 4530 to level 4455 to place the central well on a bench, reactivating the pools.

Jan 21, 2025

By R. F. Favreau, Patrice Favreau

In many quarries and construction sites visited by the authors over the last 50 years, the latter have observed muck piles from blasting with explosives, which included numerous large blocks, in some cases of dimensions larger than the input to the crusher. The names of these sites cannot be given in the article because the owners insist that data obtained on such visits be kept confidential. Often the blasters felt that the natural fissures in the rock would compensate for the use of a low powder factor, and they asked the authors to explain why such blocks were present. A detailed analysis of the situation often indicated that the cause of the blocks is that explained by figures such as 6 and 7 below in the article.

Jan 1, 2018

By L. M. Lopez, J. A. Sanchidrian

This work investigates the performance of some of the measurement techniques used in vibrations from blasting monitoring. Two tri-axial geophones with cases of different size, shape and mass were tested in a shaker table. The geophone cases were mounted in three different ways on a granite slab fixed to the plate of the shaker: freely placed, sandbagged, and anchored. A known horizontal periodic motion of constant amplitude, and frequency from 16 to 200 Hz, was applied to the slab. Two amplitude levels of 5 and 20 mm/s (0.2 and 0.79 in/s) were applied when the sensors were sandbagged or anchored and only 5 mm/s when no holding force was applied. The transmissibility of vibrations from the rock to the longitudinal geophone as function of the frequency (i.e. ratio of response of the geophone to the slab motion) has been obtained for each measuring condition tested. The transmissibility is considered a composition of the transmissibility of the rock-to-sensor coupling and the transmissibility of the sensor’s mechanics and electronics. The transmissibility of the coupling is obtained normalizing the total transmissibility with the transmissibility of the seismographs, obtained by a suitable test to which a coupling transmissibility of 1 is assigned. Geophone-to-rock coupling is a resonant phenomenon that may alter the amplitude of the measured waveforms by a factor of 1.2 to less than 0.6. The most accurate and precise measurements are obtained with geophones anchored to rock. On the contrary, freely placed or sandbagged sensors are non-predictable planting conditions that lead to high amplification or damping in most of the frequency band analyzed. It is also shown that existing acceleration criteria to select coupling methods do not necessary lead to good quality (accurate and precise) vibration data.

Jan 1, 2014

By Hideaki Kitajima, Daisuke Fukuda, Kazuma Moriya, Katsuya Sasaki, Katsuhiko Kaneko

The purpose of this research is to analyze the fracture process and achieve design optimization of a splitting method for concrete and rocks termed the electric discharge impulse crushing method (EDICM). The EDICM utilizes the cartridges being set in boreholes in the splitting target. The cartridge has a thin metal wire and is filled with nitromethane. By applying the electric discharge to the wire in the cartridge, plasma is caused leading to the vaporization of the wire. Then the deflagration of the nitromethane commences, which generates borehole pressure for splitting the target. Although the required splitting time is roughly several hundred micro-seconds and much slower than ordinary blasting, the fracturing still completes in quite short time and understanding the fracture process of opaque and brittle materials such as rock and concrete in this time scale is of academic importance.

Jan 1, 2011

By Robert Hopler

THE work that is being done by the Government to reduce the dangers of mining was brought out strikingly in the First National Mine-Safety Demonstration which occurred at Pittsburgh, Pa., on October 30th and 31st, under the auspices of the United States Bureau of Mines with the assistance of the American National Red Cross Society and the Pittsburgh Coal Operators’ Association.

Jan 1, 2012

By Neal Lee, Braden Lusk, John Silva Castro

One of the most common assumptions regarding the use of ANFO versus utilizing 100% sensitized emulsion is that ANFO “turns over” the muck-pile better, due to the “higher gas volume” supposedly inherent in ANFO. This paper examines this assumption and provides quantitative data for analysis. Total gas volume from each product was evaluated using Orica’s I.D.E.X. Code analysis. This analysis was used to determine if gas volume is a significant contributor to differences in fragmentation and movement between blasts utilizing the two different products. A constant drilling and blasting cost per yard for given cut depth, hole diameter, stemming height and rock type was utilized. The cost per yard was held constant by adjusting patterns considering product, accessory, and drilling costs. Photographic fragmentation analysis, dig rates measured quantitatively through production tracking and time studies and qualitative information about the diggability of the blast provided through video recordings were used to evaluate performance. The data collected during the study is presented and recommendations are made regarding the performance of ANFO and Emulsion holding other variables constant for a limited number of blasts.

Jan 1, 2012

By J. D. Aubertin

Rock blasting is a complex engineering process that requires in-depth knowledge of operations and geomechanical conditions. Acknowledged design precepts are based on cratering behavior associated with stiff hard rock masses. Other cratering mechanisms may however arise under certain geomechanical conditions such as extremely fractured rock masses, or with soft rocks such as rock salt and potash. The burden dimension also plays an important role in the prevalent cratering mechanisms of a given blasting condition. The present article investigates the variability of cratering profiles and geometrical trends based on characteristic geomechanical differentiation and considering the influence of burden. The differences in observable mechanisms are examined through small and large-scale single hole blast (SHB) tests. SHB tests involve a series of individual shots blasted parallel or sub-parallel to an open face. The burden dimension is varied to obtain burden dependent characteristic trends. The breakout shape is represented by a crater model in the form of a power law equation capable of describing prismatic, concave and convex cratering. The formulation comprises two reference index parameters that can describe the geometrical and geomechanical conditions. SHB test campaigns conducted in rock salt, limestone, massive amphibolite, pinolite, and grout blocks are compiled in quantitative manner to demonstrate the influence of geomechanics on cratering profiles. The observed trends are corroborated through numerical modelling carried on Finite Element Model (FEM) LS Dyna to investigate the prevalence of specific cratering mechanisms. A series of SHB tests at large and small burden values are also used to showcase the influence of geometry on the prevalent cratering mechanism and the resulting crater

Jan 1, 2024

By S Burchell

During the past few years, high-speed cameras, laser surveying equipment and photogrammetry have become standard tools for recording blast geometry and results. While laser profiling yields accurate 3-D measurements, most cameras capture only two-dimensional images. Attempts to extract 3-D information from photographs have been unsatisfactory. Recent advances in electronic imaging and computer programming have made it possible to develop a 3-D computer based analysis system which can capture and measure 3-D images quickly and accurately. This paper describes the technology to create 3-D images and to analyze blast geometry before, during and after the blast.

Jan 1, 1992

By Ruilin Yang

Kinematic approach of blast modeling refers to using the velocity, strain, or displacement as controlling parameters to model blasting, rather than the stress and the material constitutive relations. The rock stiffness or constitutive relations is very hard or impossible to obtain due to the complexity of the rock mass property.

Feb 1, 2020

By Muamer Medusalic, Kim Henley, Lucas Bottomley

The period from 2009 to 2012 has witnessed a large rise in the number of blast-generated fume events in Eastern Australia, where highly visible oxides of nitrogen (NOx) are produced from coal mine blasting. Fume production mechanisms have been poorly understood by mine operators, and practical measures to reduce fume were initially elusive. Over time, data on fume events has been collected and analysis has pointed to a range of contributing factors associated with fume production.

Jan 1, 2012

By Robert Lee, Pertti Paavola

Automated vibration monitoring and web-based data distribution has proven itself on the largest single construction project ever undertaken in Finland. The excavation for the Kamppi Center Project in the center of Helsinki was completed in November of 2003 and involved the removal of over 200,000 m3 (260,000 yd3) of rock and over 1,700 individual blasts. A system was installed, incorporating 37 discrete monitoring points located throughout an underlying metro station, and other surrounding underground and surface facilities. After every blast, vibration data was automatically transferred from the monitoring network to a server database. Stakeholders were able to access and review vibration reports on a password-protected website within 90 seconds of each blast. This allowed engineers to verify that recorded levels were in compliance with established limits, before proceeding with subsequent blasts. The data was also imported into a semi-automated Scaled Distance tool for analysis using linear regression techniques. This was used to determine, and adjust for trends in blast-induced vibration.Copyright

Jan 1, 2004

By Ricardo Chavex, Adrien Letellier

Flyrock remains one of the most critical issues in open-pit blasting. Despite the significant improvements made with modern surveying methods, the necessity remains to define sensible danger zones around blasting areas. Therefore, many semi-empirical models predict flyrock distances based on trajectory calculations and probabilistic adjustments. However, most are merely based on nominal parameters, even though a considerable amount of precise data is nowadays available thanks to modern measurement techniques using lasers, GPS, drones, and probes. These data provide accurate information about the actual field circumstances of a blast concerning geometry and rock-mass conditions. So how can we use and integrate them into existing flyrock models? The answer to this question can significantly improve the accuracy of flyrock prediction models and enhance safety. This paper will present a method to adapt existing models to actual field data using appropriate software and digital tools during the blast design process. In addition to calculating a more pertinent danger zone perimeter, this method provides an efficient and practical tool that helps prevent flyrock incidents. Indeed, it allows the blast designer and shot firer to be warned if there is a hazardous critical deviation due to local conditions. Moreover, it also enables blasters to communicate better and share the visualization of the blast-specific evacuation zone. The paper will also discuss how this method can be calibrated and how it has been used to analyze some actual flyrock incidents.

Jan 21, 2025

By Markus Pötsch, Andreas Gaich

Optimization of surface blasting based on 3D models from drone imagery and a closed loop that starts with an automatic analysis of the geometry and the geological conditions and ends with an objective assessment of the blast result.

Feb 1, 2020

By Thierry Bernard

To be able to precisely predict the result of a mine blast before pressing the button is a goal for many blasters due to the environmental and economic constraints of our century. Based on the fundamental fracturing of the mechanism of rocks by explosives, the most recent research in digital modeling, the power of present computers, and the possibilities offered by drones, we have designed a realistic digital 3D simulation model for mine blasts

Feb 1, 2020

By Nathan Rouse

This blast mitigation study examined the effects of a barrier wall on explosively driven pressures. This area of blast mitigation is of interest due to the many different applications involved in protecting a target from an explosive attack.

Jan 1, 2012