Search Documents

By David E. Siskind

Increased mineral consumption and environmental concern have caused much interest in potential damage and annoyance from ground vibration and airblast produced by production blasting in surface mines and quarries. Ground vibrations are traditionally blamed for "shaking the house to its foundations," but often the airblast is responsible, particularly when the distances from mine to structure are large. Simultaneous measurements of ground vibrations, structure vibrations, and indoor and outdoor noise from blasting are being used by the Bureau of Mines to determine the relative importance of the ground and airborne blast energy in shaking the structure and making windows, dishes, etc., rattle.

Jan 1, 1977

By Kurt B. Oakes, Brian M. Fortelka

Unimin Corporation operates an underground Silica Sand mine at Guion, AR located in North Central Arkansas. The Silica Sand deposit at Guion is part of the St. Peter Sandstone Formation, which is overlain by a competent dolomitic limestone from the Joachim formation, acting as the roof directly above. Both the St. Peter and the Joachirn Formations are of Middle Ordovician age.

Jan 1, 1999

By Lyall Workman

New mines are frequently located at altitudes above 3,000 meters (10,000 ft.). Drill selection must take the altitude effects into account, to insure high productivity and good bit life. In particular, compressors must be sized differently than for low altitude operation. A larger compressor is required to deliver adequate air to the bottom of the blasthole. Many drills in remote locations use diesel engines as the prime mover. Altitude effects on engine performance should also be considered.

Jan 1, 2007

Over 45 of the Best Qualified Technical Specialists, Consultants, Engineers, Scientists, Explosive Supplies, Educators and Mine Operators in the World!

Jan 1, 2000

By Goran Lande, Bernt Larsson, Dennis Clark

The effects of vibrations on close surroundings has been studied in Europe and the United States extensively in the past three to four years due to the ever increasing demands of environmental control. Therefore, "routine measurements" or "standard vibration consulting services" are being carried out by numerous firms with widely different qualifications.

Jan 1, 1983

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By Brandon Fryman, Josh Hoffman, Rhys Baker

A post-detonation debris collection project was led in conjunction with a large ammonium nitrate (AN) railcar detonation conducted by the Department of Homeland Security-Transportation Security Administration, Department of Defense-Combating Terrorism Technical Support Office, Sandia National Laboratories, and the U.S. Army Dugway Proving Grounds. This important work will aid in underpinning algorithms used in a Quantitative Risk Assessment (QRA) tool.

Feb 1, 2020

By Virgil L. Lewis

On September 7, 1994, a Burlington Northern coal train crashed into a parked train in the downtown Gillette, Wyoming rail yard. I would like to address two issues in regards to this accident. One, a slide presentation of the damage created by the accident and the resulting required clean-up and two, a simulation of "what if" had there been an explosion during the course of the crash.

Jan 1, 1996

By Lon Santis, Michael Swisdak, David Leidel, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc (APT) have developed and released a quantitative risk management tool, IMESAFR (IME Safety Analysis For Risk), for the commercial explosives industry. Consequence algorithms in IMESAFR are considered state-of-the-art. Generally, they mirror those in SAFER (US Department of Defense Explosives Safety Board quantitative risk management software). The science behind the software has now been assessed for its maturity. Results have identified areas where additional test consequence data could improve predictions. To address these areas, full-scale testing programs to provide the needed data have been formulated. Proposed testing efforts include work to: (1) improve characterization of explosive articles now absent from SAFER, and (2) refine modeling of the Potential Explosion Site (PES) types, particularly small metal structures, also not found in SAFER. Goals of each program as well as requirements for conducting the tests have been established. Testing results are to be used to improve the algorithms and to further the state-of-the-art in risk-based explosives safety.

Jan 1, 2012

By Jorge Flores, Dean Nichols

Some view quantitative risk assessment (QRA) as difficult to understand and complicated to use. They are comfortable with the proven reliability of quantity distance (QD) and question the benefits of applying QRA principles to explosive safety. In response to such questions, a review of the history of the American Table of Distances (ATD) provides insight to the strengths and weaknesses of the concepts behind QD tables. Additionally, a closer look at QRA features that are available today will reveal stunning capabilities and improved user friendliness not available previously. This paper looks at the early days of explosive safety, the use and limitations of QD, the meaning of risk in the context of QRA and discusses recent developments that knock down barriers previously hindering acceptance of QRA among regulatory agencies.

Jan 1, 2015

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By Joshua Hofman, Braden Lusk, Erin Morris

Explosions in urban environments, whether of accidental or malicious cause, often result in extensive injuries, loss of life, and property damage. The ability to predict the damage inflicted by these events is highly sought after; in order to predict damage, the behavior of blast waves within these environments must be quantified and understood. Urban constructs such as buildings and roadway intersections affect the natural propagation of a blast wave, intensifying or rarefying the wave depending on their arrangement.

Jan 1, 2012

By Cary Moffat, John Kita, Rick Walker

The Lac des Iles Mine, in an isolated area of NorthwesternOntario is a relatively new open pit platinum and palladium mine. They were encountering problems with the equipment and production scheduling when ramping down to begin production on the subsequent benches. A co-operative effort between Lac des Iles Mine operation people, ICI Explosives, and the mines drilling and blasting contractor - Consbec Inc., resulted in a decision being made to use full depth sinking cuts to provide access to the next bench.

Jan 1, 1996

By Bjorn Engsbraten

Explosive charges have been fired under defined conditions in a closed tunnel. The explosives have either been detonated in a steel tube or a single borehole. In the latter case dimensions, -loading density and confinement have been chosen to correspond to common practice.

Jan 1, 1980

By Sunil Vytla, Akash Adhikari, Purushotham Tukkaraja

Blasting operations produces gases and fumes that may be toxic or non-toxic in nature. A detonation of commercial explosives such as ANFO, emulsion, and dynamite would ideally produce only nontoxic products such as steam (H2O), carbon dioxide (CO2) and nitrogen (N2). However, in the real world, the detonation of explosives produces toxic products such as nitrogen dioxide (NO2), nitric oxide (NO) and carbon monoxide (CO). The focus of this study is the blast fumes entrapped in the muckpile. Fume clearance and workplace re-entry time studies performed in the past have overlooked the toxic gases entrapped in the muckpile. Studies show that as much as 60% to 70% of the fumes or gases produced during blasting underground can remain entrapped in the adjacent rock mass or in the muckpile. The toxic fumes trapped inside the muckpile are slowly released and could be fully uncovered during the mucking process. Exposure to these gases or fumes is hazardous to mine workers. In this study, author have analyzed the nature of fume flow, i.e. accurately predicting where and how the fumes flow after an underground development/tunnel blast. This will help in determining i) precise re-entry times for the workers ii) rate and direction of the fume flow. Computational Fluid Dynamics (CFD), a mathematical simulation technique that predicts fluid dynamics phenomena is used for this purpose. CFD is preferred over physical models because it is inexpensive, once the accuracy is established, a wide range of scenarios can be simulated quickly, and the toxic gas flow patterns through underground openings can be analyzed efficiently. For this study, CFD is performed using SC/Tetra software owned by MSC software company.

By Roger Holmberg, William Hustrulid

Swedish cautious blasting techniques were used to excavate a room at the CSM Experimental Mine in Idaho Springs, Colorado,as part of a ONWI/DOE sponsored nuclear waste disposal research program.

Jan 1, 1981

By Norman Paley, John Kells

The climate and location of the Red Dog Mine present several challenges to blasting operations. The mine is located north of 68º latitude, in an area of continuous permafrost. Ground temperatures are below freezing year-round and air temperatures range from -40 to 70°F (-40 to 20°C). Because there is no overland access to the mine, the entire year’s supply of bulk explosives, approximately 7,000,000lbs (3,175,000kg) is shipped in by barge during the 100 day shipping season when the port is ice-free. The first week in July is the earliest that new product arrives at the port. Emulsion usage is maximized from mid April through October when surface water fills the blastholes during drilling. This necessitates that a considerable portion of the bulk explosives are stored for 10 months or more before usage. The emulsion is routinely pumped from the ISO containers at temperatures of 20ºF (-7°C). The mine engineers conducted a testing program during the 2001-2 blasting season to identify the bulk explosives best suited for the conditions at the mine. A secondary goal was to decrease the usage of sensitized emulsion, as this is the most difficult portion of the explosives order to ship. To ensure repeatability when transferring the results to the day-to-day blasting operation, the majority of the testing was incorporated into normal blasting operations in the field. The mining methods used at Red Dog Mine make direct fragmentation analysis impractical and performance testing in the field relied primarily on VOD measurements. The products were also tested for their ability to be pumped in cold temperatures.

Jan 1, 2004

By Milton Barbosa Landim, Denise de La Corte Bacci

Statistical methods of multiple regression analysis, trend surface analysis and principal components analysis were applied to seismographic data recorded during production blasting at a diabase quarry in the urban area of Campinas (SP), Brazil. The purpose of these analyses was to determine the influence of the following variables: distance @), charge weight per delay (W), and scaled distance (SD) associated with properties of the rock body (orientation, frequency and angle of geological discontinuities; depth of bedrock and thickness of the soil overburden) in the variation of the peak particle velocity (PPV). This approach yielded variables with larger influences (loads) on the variation of ground vibration, as well as behavior and space tendency of this variation. The results showed a better relationship between PPV and D, with D being the most important factor in the attenuation of the ground vibrations. The geological joints and the depth to bedrock have a larger influence than the explosive charges in the variation of the vibration levels, but frequencies appear to be more influenced by the amount of soil overburden.

Jan 1, 2002

By B Kniivila, A B. Andrews, T Lerick, Keith Jansen

Minntac Mine is a large, open pit taconite mine located at the center of the Mesabi Iron Range in northern Minnesota. The planned development of the Mine in the direction of nearby communities prompted a comprehensive study of off-site blast effects that resulted in numerous refinements in blasting practices.

Jan 1, 1984

By Lon Santis, Bill Evans, John Tatom

Debris data from the Department of Defense Explosives Safety Board’s Project ESKIMORE full-scale explosives event test program are compared to quantity-distance (Q/D) standards and quantitative risk analysis (QRA) methods. The ESKIMORE test program involved quantities of explosives ranging from 1,000 to 60,000 pounds detonated in typically sized structures made of metal and concrete. Debris from these events was extensively surveyed and catalogued. The debris patterns from these events show varying degrees of directionality normal to the walls of the structures. These density patterns are overlaid an existing explosives storage site that is comparable to the test conditions. Analysis of the debris patterns in relation to Q/D standards shows that exposures located beyond the Q/D arc but along the normal to walls of potential explosion sites (PES) may have much higher debris density than exposures at the same distance on the corners of the same PES. Analysis of the debris patterns shows that predicted patterns using the QRA tool IMESAFR v2.0 closely match actual patterns. Additionally, IMESAFR based QRA methods are able to quantify the different risk levels of being exposed along the wall’s normal as compared to being exposed on the structure’s corner. Methods and decision making criteria to mitigate risk based on the directionality of PES debris are presented. Copyright ©

Jan 1, 2015