Search Documents

By Alvin D. Christmas

The missing link is a connector between the congested downtown area of Knoxville, Tennessee adjacent to the former World's Fair site, the I_40 I_75, and Western Avenue traffic arteries. This connecter was designed to accommodate the 37,470 motorists who presently travel through these highly congested narrow paths to be replaced by the 21.8 million dollar Henely Street Connecter. All construction and blasting was to take place while existing traffic was re_routed so as to allow access between the downtown area and the vital interstate corridor. To avoid major traffic problems, the project was to be accomplished in three phases: (1) the Western Avenue viaduct demolition; (2) two new viaducts to be constructed; (3) the open box cut at Henely Street next to the L & N Depot. Due to the past attempts by the Fort Sanders Community Home Owners group and the Historical Society to stop the Henely Street Connector, this project involved a very comprehensive blasting damage control program with special provisions of .5 inches per second measured at the foundation of the closest structure.

Jan 1, 1995

By James C. Irvine

Meramec Mining Company's Pea Ridge underground mine is presently involved in a large scale pillar recovery program and has made use of both rotary and down-the-hole drills for large diameter blastholes. Groups of pillars have been blasted with water gels in massive blasts which have broken in excess of one million tons of ore per blast. An outgrowth of the pillar recovery program is the combination of rotary and down-the-hole drills to develop vertical "raises" between mine levels. This paper outlines the Pea Ridge procedure for pillar blasting including the use of non-electric caps. Techniques and loading rates are discussed, and safeguards against blasting damage which were developed as a result of the program are presented.

Jan 1, 1976

By Florian Bauer

The Fording River mine in British Columbia produces hard coking coal in an open pit operation. Coal seams are exposed by blasting overburden and digging blasted muck with rope shovels. The drilling and blasting process presents a considerable cost factor to the operation. Reducing the amount of explosives needed therefore contributes considerably to costs saving initiatives. However, reducing the powder factor only makes sense if the subsequent loading processes by the shovels are not compromised in terms of productivity.

Jan 1, 2014

By H. R. Maggard, C. M. Bollinger

Solving the problem of detecting underwater explosions from "dynamite fishing" can be done by using a system of sonobuoys programmed to detect the acoustic waves from underwater explosions. The system includes three anchored sonobuoys, which have radio communication to a central station. Each sonobuoy will detect the direction the blast occurred, and then send the magnitude of the acoustic waves and the blast direction to the central station where the blast distance will be calculated. The central station can the send the coordinates to the authorities who can find the location using GPS systems onboard their boats.

Jan 1, 2004

By John Cowin, Dan McCutchen

Cowin & Company has specialized in underground construction since 1924. This paper reviews the sinking of two shafts in the Alabama coal fields using bulk-loaded explosives. Each shaft is eighteen hundred feet deep, and their diameters were twenty feet and twenty-three feet. The first consideration in changing to a new explosives system was safety. Safety began with the explosive supplier training the miners in the use of the new system, from explanation of the pumping unit on the surface to hands-on training in the shaft. The considerations covered include establishing a thunderstorm exit plan, and reducing exposure time of the crew to explosives while loading. The system consisted of a specialized pumping unit and an advance emulsion product. Eliminating the need for nitroglycerin based explosives, and reducing sensitivity to mechanical shock were goals that were met. Performance in the shaft and ease of use meant morale of the miners using the system remained high and positive. Performance benefits discussed include reducing the number of holes in the round, and cutting explosives loading time in half. Damage to the ribs of the shaft was greatly reduced, making it safer to work near the ribs on succeeding rounds. Cleaning the bottom before drilling the next round also showed marked improvement. The economics of the system became very apparent when cycle time saved was allocated against fixed cost of sinking these shafts.

Jan 1, 2000

By Alastair Torrance, Braden T. Lusk, MinGi Seo, Gary Cavanough

Velocity of Detonation (VOD) is the most commonly used method to determine explosive performance as VOD is a function of the confinement (ground conditions) density and composition of the explosive. Techniques used to measure VOD include resistance wire, time domain reflectometry, simple start stop and fibre optic methods. All these approaches require a cable of some sort to be inserted into each blast hole being monitored and the holes to be fired in a specific sequence. It is time consuming and fairly technical to position the cables correctly to gather the data from each hole. It slows down the hole loading process and increases the number of people on a bench at that time. The equipment and cable limits the measurements to a few holes, typically 5 or less, that are in close proximity. These measurements can generate useful information about the monitored holes but does not provide a full picture of how the explosive is performing across the whole blast and whether any change in performance is noted with changing ground conditions or confinement.

Jan 1, 2019

By Donna Kliche, Charles Kliche

It has been previously documented that various weather conditions such as wind direction and speed, cloud cover and, especially, temperature inversions can significantly affect the overpressure generated by a blast event (Siskind et al, 1980; Oriard, 1999; Siskind, 2000). The overpressure can be magnified downwind and reduced upwind; a change in the regular profile of temperature with elevation can magnify or focus the sound intensity at some distance from the blast event.

Jan 1, 2011

By Xue Yongpeng, Zhu Zhenhai, Zhu Ming

The purpose of the Solid Medium Controlled Blasting Technique and Its Applications is to have the inside of the vessel-shaped framework (e.g: oil tank , water pool, gas chamber, chimney, water tower, grain warehouse and etc.) or the one side of the thin wall-shaped structure(e.g: steel bar concrete wall and etc.), both of which are intended to be demolished, inserted with the required solid medium (e.g: soil , sand , coal, salt and etc.) ,in which there is a certain mass density, and then through which the blasting energy is transferred to fulfill the blasting task. For such a technique, it is necessary to bury the explosives into the inserted solid medium and then to start the explosion to blast the intended target into pieces. The filling of the solid medium may be done mechanically or by man. Compared with the water pressure blasting technique, this one has the characteristics of good effect. wide application, simplified construction procedure , safe and reliable operation and small vibration (less vibration than water pressure blasting by 80% to 90%)in particular without any flying stones, thus resulting in better and comprehensive social and economickfficiency.

Jan 1, 2000

By Derek Morris, Vito Saccheri

In the monitoring of seismic exploration (whether by explosive or vibratory energy sources), the intensity of shaking at neighboring structures can now be measured quite accurately and comprehensively with portable equipment. However, the interpretation of the results is open to considerable debate and mis-interpretation. One conventional approach is simply to compare the maximum measured peak particle velocity (PPV) with a permissible standard – usually 0.5 inches/sec (1.3 cm/sec) because this is the value generally referred to in the U.S. Bureau of Mines standard. This can be very conservative, both for surface structures, and especially for buried structures like pipes, for which absolute reliance on PPV obscures the true complexity of field problems. Quite apart from the fact that the full Bureau of Mines standard is actually a reasonably complex function of frequency (for the simple reason that in differing parts of the frequency spectrum, damage may be displacement or acceleration controlled), the effects of spatial direction and orientation are often ignored.

Jan 1, 2009

By J. P. Remi Proulx, Juan Camilo Gonzalez T., Winston B. Wilches

Alabama USA based Drummond Ltd. operates two open pit mines in the Cesar Coal Basin of Northern Colombia. The mines produce a combined total of over 25 million tons (22.7 Mt) of thermal coal per year which is transported by rail to Puerto Drummond, a direct ship loading facility, where it is exported to over 15 countries. The company has proven and probable reserves in excess of one billion tons of thermal coal.

Jan 1, 2015

By Robert B. Hopler

Reefs, exposed rocks, and fast currents made the Hell Gate section of New York's East River a treacherous passage ever since man attempted to sail through the area. As the harbor's importance grew, attempts to improve the channel were made, starting in 1851. This paper discusses the first major organized effort to clear the area, which began in 1869 and culminated in a single large blast in September 1876.

Jan 1, 1981

By Gregory B. Poole

Data collected with 16K sampling at a variety of blasting sites (construction, quarry, trench, mine) and monitoring locations was analyzed to effectively show the 16 different 1K readings all based on the microsecond that the unit went into monitoring.

Feb 1, 2020

By Seung-Kyu Baek, Chang-Ha Ryu, Yang-Kyun Kim

Safety concern is one of the most important parameters in the design of building demolition by explosive blasting. Accidents were sometimes reported due to the flying chips of fragmented materials in building demolition work in urban area. Laboratory experiments were performed to investigate the failure behavior of reinforced concrete pillars under blast loading and to develop an effective protection technique. Sixteen reinforced concrete pillars were constructed with two sizes: 450×450×1800 mm and 600×300×1800 mm. The failure behavior and the flying chip velocities were observed by means of a high-speed camera. Protection scheme was designed and the effects of several protection materials were investigated. Two kinds of non-woven fabrics and wire net were tested as protection materials. The results showed that reinforcing bar was one of the important factors to determine specific charges, and that mesh size of wire net and tied-up method affected the protection of flying chips. Control of gas effects is also a key to the control of flying chips. It was recommended to use both wire net and nonwoven fabrics as primary and secondary protection materials. Such protection scheme was successfully applied to the explosive demolition of 16 and 17-story apartment buildings.

Jan 1, 2002

By Stephen Chung, John Carpenter, Scott Gosch, James Breedlove

While controlling fly rock and ground vibration in quarrying in the neighborhood of a residential area, producing good fragmentation and keeping different grades of material separated in a muckpile are important in maintaining the productivity of quality aggregates. This paper describes a single row production blast for the study of fragmentation and displacement in the grade control carried out at a quarry of Barrett Paving Materials Inc. in Sylvania, Ohio. Digital video imaging was used to monitor the blast-induced motion of the bench face as input to the DMC_Blast (Distinct Motion Code), for the analysis of the formation of the muckpile. The actual digitized blast video and the DMC_Blast simulation are compared. The displacement and mixing of all the inter-bedded limestone layers are made visible in the simulated cross-section of the muckpile. The apparent fragmentation analysed with PowerSieve is also discussed.

Jan 1, 2001

By Lon Santis

This paper analyzes 110 serious accidents that occurred during the use of commercial explosives in mining, construction, and other industries since 1992. Data from the Mine Safety and Health Administration (MSHA), the Institute of Makers of Explosives (IME) members’ reports, and media reports were used. Only accidents that resulted in a fatality, significant lost work time, or injury to the public were considered in this analysis. The accident data were analyzed for trends in frequency, type of industry, cause, type of individual harmed, and geographical region. Although the data showed that explosives accidents are decreasing in frequency, still, 29 people were killed and 134 injured. Eightyfive of the accidents occurred in mining, 17 occurred in construction, and 8 occurred in other industries including oil recovery, seismic exploration, agriculture, logging, boiler cleaning, and avalanche blasting. As other studies have shown, flyrock and failure of blast area security caused over half of the accidents. Mishandling, misfires, or fumes caused just over one-third of the accidents. Lightning and drilling into explosives were responsible for the remainder of accidents.

Jan 1, 2003

By Lawrie Logan, Mike Wiggin

This paper will be in two parts, a discussion of the benefits available from benefit sharing as a concept followed by an examination of how this approach was applied at Mesa J Mine and what improvements were made. The first part is an outline of the ways that both parties in a benefit sharing agreement can uncover additional wealth by bringing a new approach to the relationships between mine and supplier. The paper describes a partnering agreement recently established between Robe River Iron Associates (RRIA) and Dyno Nobel Asia Pacific Ltd (DNAP) to access the wealth locked up by the usual explosives supply contracts in Australia and elsewhere. The partners are acting cooperatively to maximise the benefits to both parties from optimising blasting practices at the Mesa J Iron Ore Mine in the Pilbara region of Western Australia.

Jan 1, 2001

By Brian Hawkins, David Bradley, Rachel Gooding, Lucas Rodriguez, Patrick Wilson, Kevin Wegman, Dhruv Mittal

To better protect the nation and inform difficult defense and preparedness decisions, the Department of Homeland Security (DHS) is performing a probabilistic risk assessment of explosive terrorism risk to the US homeland. After assessing existing models against requirements, well-developed mathematical descriptions and algorithms associated with explosives hazards were combined with probabilistic modeling techniques used in DHS chemical, biological, radiological, and nuclear (CBRN) terrorism risk assessments to create a suitable interior explosive consequence model for assessing the impact to human health.

Jan 1, 2018

By Hae-Moon Choi, Sang-Don Lee, Hee Soon Shin, Choon Sunwo, Chang-Ha Ryu, Hyun-Koo Lee

Building tunnels means dealing with what rock is encountered. Relocation of the site of the underground structure is rarely possible. Tunneling engineers and miners have to cope with the quality of the rock mass as it is. Different tunneling philosophies and different rock classification methods have been developed in various countries. Most of the rock classification methods are based on the response of the rock mass to the excavation. Tunnel support requirements could be assessed analytically, supplemented by rock mass classification predictions, and verified by measurements during construction. Rock mass classifications on their own should only be used for preliminary, planning purposes and not for final tunnel support. Design of blast pattern in tunneling projects in Korea is also for the most part prepared according to the general rock classification methods such as RMR or Q. It, however, does not take into account the blast performance, and as a consequence, produce poor blasting results. In this paper, the methods of general rock classification and blast design for tunnel excavation in Korea are reviewed, and efforts to develop a new classification method, reflecting the blasting performance, are presented. Copyright ©

Jan 1, 2004

By Y Wada, Y Ogata, T Nishida

"Shaped charge is used for blast demolition of steel construction in general. It is important tocontrol movement of cutting part with shaped charge for the blast demolition of steel construction.Movement of cutting part was studied in the small scale experiment with steel bar. A numericalsimulation using the Discontinuous Deformation Analysis (DDA) was carried out. The DDAmethod was applied to the full scale blast demolition of steel construction. Results of thesenumerical simulation was compared with the blasting demolition work of steel tower."

Jan 1, 1999

By J. Silva, M. Kotraba, F. Pontanilla

Blasting is the application of highly complex science that, in some cases, could be viewed as an art. Many variables are involved in a blast, including geology, pattern design, timing and firing sequence, and explosives selection. Assuming that better results can be achieved by only increasing the powder factor is inaccurate. The Drill-to-Mill (D2M) concept has been in the mining industry for over two decades. The D2M approach is commonly viewed in an oversimplified manner, assuming that by simply increasing drilling and the amount of explosives used (both of which add operational costs), the downstream value will be created. An optimized D2M initiative should combine the smart application of explosives at the beginning of the mining process, matching the dynamic properties of the rock to the explosive selected to improve the efficiency of the energy created by the explosive to the rock mass being blasted, and to bring benefits to the mining operation across the entire mining and processing value-chain. This paper reviews the principles behind matching the shock impedance of the rock and the explosive and compares the traditional use of explosives versus the smart application for two hypothetical blasts.

Jan 1, 2024