Search Documents

By Michael S. Wieland

"This report investigates whether it is tractable and thereupon reasonable to remove the boosterinfluences when ranking the toxic fumes of non-cap-sensitive mining explosives. The hazard potential is represented by relative fume toxicity RFT, the resultant influence computed from a formulated rule with a restricted set (tally) of fume components and multiplying constants. The RFT result is compared to the rule criterion that represents the worst case tolerable toxicity stipulated by regulations or otherwise. The typical nonstoichiometric booster composition can render notable unwanted influence on the RFT ranking results. Historically, the remedy was to shoot the booster separately and reduce the trial concentrations by the relevant subtractions. Unreal negative concentration results were noted on rare occasions, revealing the faulty nature of the reduction procedure. With thermodynamic reaction chemistry codes TDRC, on the other hand, the booster ingredients can be retained in or removed from the reactant tabulation, yielding reduction factors taken as the concentration ratios for the two circumstances. The underlying presumption regarding reduction factors is that the ratios of component concentrations with and without the booster ingredients when resolved theoretically ought to equal those rendered experimentally, when tractable. Upon rearranging the presumed relationship, the unadjusted fume concentrations divided by theoretical reduction factors yield the wanted readjusted fume concentrations, thereby removing the booster influence without generating unreal negative concentrations."

Jan 1, 1999

By Lynn Long

We have seen many new developments in the explosive and blasting accessory category, but one of the most useful items is the blast control plug. Blast control plugs are cone shaped units that are placed in the stemming just above the explosive load. They are placed about 8 to 12 inches up into the stemming material.

Jan 1, 1996

By Scott G. Giltner, Alex Schwenk

An iron operation sought to extend the life of the mine by conducting a major pit pushback in an area close to several public structures and the neighboring town. The result of the pushback would make millions of tonnes of ore available for mining allowing many additional years of taconite mining. This paper discusses the initial development blasts conducted for the pit pushback. For the development blasts, it was determined that no fly rock should leave the mine site and that the blast vibrations should be as low as possible, but specifically under 19 mm/s (0.75 in/s) at a nearby sewage treatment plant. One issue complicating the blast design was the variation in hole depth within any given blast. For the initial sinking shot, the hole depths varied from 6.4 m (21 ft) to 12.5 m (41 ft). In the subsequent blasts the hole depths within each blast could vary up to 5.8 m (19 ft). Various tools were employed to design the blasts to ensure there was no fly rock and that the blast vibrations were as low as possible. UAV surveys of the blast areas were conducted to provide a 3-D representation of the free faces and bench surface. The 3-D point cloud produced from this was used to measure the shape of the free faces. Once the shape of the free faces was quantified, it was possible to establish proper placement of the crest holes and develop a custom explosive load for each blast hole. In addition, signature hole analysis was performed for each blast to determine the optimum delay time that balanced the need for minimal vibration, prevent fly rock, and a well fragmented muck pile. Electronic detonators were applied to achieve the necessary control of the blast that balances these three concerns. The results of the seven blasts conducted to date provided the desired results. The peak vibration level at the sewage treatment plant for the seven blasts was 10 mm/s (0.40 in/s). The only fly rock occurred when there was a miscommunication in the blast design resulting in under burdened holes on the front row. To date, the mine has been able to safely expand the pit into an area that will add many years to the mine life. The muck piles have been well fragmented with reports from the shovel that they have all dug well.

Jan 21, 2025

By Keith Best

It has been said that when a person does something right no one remembers but when they do something wrong no one forgets. This statement, when applied to the explosives industry, has never been truer. Think about it.How many times have you seen a news crew reporting on how well a blaster is doing his/her job? Normally, all you will see is how bad things are going and how much “damage” is being done.

Jan 1, 2008

By Kevin Phelps, Jason Baird, Philip Mulligan, Dominique Nolan

Determining the transitions from run-up to optimal cut length and optimal cut length to run down, without bias, from the penetration of a linear shaped charge (LSC) is difficult. The stresses applied to the targets during explosive testing can distort the targets in such a manner that determining the true distance of cut, penetration, or fracture can be demanding. Through the course of this research, it was observed that the researchers made many of the errors involved in the collection of data. Among these errors researchers found problems in: determining and fitting the sample to a single plane from which to read measurements, determining where along the path of cut the three phases of penetration transition, and the precision of measurement based on handheld tools and the human eye. This study looks at three methods of recording the data of a series of linear shaped charge tests. The tests resulted in samples which are not ideal for measuring with common laboratory devices like measuring tapes, calipers, or rulers. The first method utilized these common laboratory devices and the difficulties the authors experienced are described in this paper. The second and third methods involve digital photography, image manipulation, and the use of AutoCAD. Methods two and three are then compared to the simple observational method and discussion is made in regards to the precision and accuracy of each method.

Jan 1, 2013

By Jason Baird, Philip Mulligan, Caleb Baumgart

This report details the pressure variances, measured at four pressure sensors placed equidistant from the center of an airburst explosion, as the blast pressure from a single charge expands radially. Many of the empirically derived equations used for predicting the blast pressures of an explosion, assume a point source detonation and that the radial pressure expansion is equal. The authors understand that the equations used to approximate the blast pressure may not have 100 percent agreement with the observed pressure. However, during previous research at Missouri University of Science and Technology (Missouri S&T) the pressure variances had a range of 1,200 psi, between the four pressure sensors placed two feet from the center of a 1/2-pound (226.8 gram) of hand packed C4. The variances indicated that at the close distance from a suspended explosive charge the pressure does not behave as that observed from a point source.

Jan 1, 2014

By John Manka

Emulsion explosives consist of an aqueous oxidizer phase, a fuel phase, and an emulsifier. The ability to use lower-cost sources for any of these raw materials presents an obvious economic advantage to emulsion manufacturers. This paper focuses on using low cost waste drain oils as the fuel phase in emulsion explosive applications. Laboratory studies showed that emulsions made from waste drain oils and agricultural ammonium nitrate prills were usable for emulsion explosives though their shear stability was weak. Customer field results proved that waste crankcase drain oil could replace half of the virgin diesel fuel in emulsion explosives to make an effective emulsion explosive product with a very low cost.

Jan 1, 2003

By Joshua Hoffman, Braden Lusk, Kyle Perry

Shock tubes are used to simulate large-scale arena explosions without the use of full-scale arena sites that utilize large quantities of explosives. Instead, small explosive charges can be used to drive shock tubes. When this is done, the geometries of the explosive charges can alter the resulting pressure time curve. A common geometry chosen for the explosive charge is a sphere in order to be congruent with the spherical shockwave that emanates symmetrically in three dimensions from the detonation point. This paper reports on the findings from experiments that study the effects of altering the charge geometries and explosive types while keeping the TNT equivalency constant. Peak pressures and durations were affected by these changes. Directional phenomena are exaggerated by the use of certain charge shapes and detonation points. The speed of the detonation front in the explosive being greater than the speed of the shockwave in air played a critical role in the resulting pressure time waveforms. Waveform manipulation can be used to generate job specific waveforms that ultimately benefit the shock tube operators and their clients.

Jan 1, 2010

By Jorge Flores, Benjamin Cebrian

Blast Optimization at a high altitude mine operation involves not only the selection of the right drilling designs and explosives but also the circumstances of operators working at low oxygen levels and low temperatures.

Jan 1, 2015

By Charles Dowding, Cathrine Aimone-Martin

This article summarizes an investigation of the structural response of a brick façade home in New Mexico. The subject Ricter residence was located some 1100 to 1400 ft away from an aggregate quarry, and was subjected to a maximum peak particle velocity and air blast over pressure of 0.29 ips and 122 dB, respectively. Superstructure (corner) and mid-wall responses to blasting and human induced activities were measured. An existing exterior crack in the brick work was instrumented to measure crack width response to blasting, human induced activities, and environmentally induced changes in temperature and humidity. Crack and structure response data were correlated with ground velocity and airblast excitations. Amplification of ground motions at the upper structure were calculated and compared with values for typical wood frame structures. The natural frequency and damping characteristics of the structure were determined to compare with measured amplification values. Wall strains produced by bending and inplane tension strains were computed from upper corner structure response and compared to failure strains for drywall and brick veneer. Calculated strains were found to be far lower than those required to crack brick and environmentally induced crack response was found to be far greater than that caused by blast induced ground motion or airblast overpressures

Jan 1, 2005

By Frederick B. Kuhnow

Harmonic energetic delamination of T2 building is being considered for demolition at a formerly known atomic lab. The T2 building is within a containment structure that is under a negative pressure of -49 Pa (-0.2 inches of WC) so that no remaining radioactive material is leaked out. The T2 containment enclosure is a portal frame-type system that spans east/west over 35.05 m (114’-11 7/8”) and spaced 2.9 m (9’-6”) apart. The west side of the portal frames is supported by a 64 cm (2’-1”)thick concrete wall which is backfilled to the west and open to the T2 basement to the east. The east side of the portal frames is supported by a 61 cm (2’-0”) thick concrete wall that is backfilled to the east and open to the tank farm vaults to the west. A concrete slab-type footing supports both the east and west walls. Transverse walls provide lateral support for the walls as part of the original design. The west wall has an elevated slab that provides further stiffening of the concrete wall between the transverse walls.

Jan 1, 2017

By Michelle Crull, Susan Hamilton

Explosives safety requirements in the United States began in 1909 when the American Railroad Institute questioned explosives manufacturers regarding distances necessary to protect employees and property. In response to this inquiry, a group of explosives manufacturers collaborated to study over 200 explosive accidents. This study resulted in the 1914 American Table of Distance (ATD) published by the Institute of Makers of Explosives (IME). The 1914 ATD provided suggested separations between explosives and inhabited buildings, public highways, and public railways.

Jan 1, 2010

By Jorge Cárdenas Miranda, Hector Espinoza

Currently in open pit mining in Peru with double bench, it is a challenge to optimize fragmentation in the drill rows near to the slopes to ensure the performance in the loading and haulage operation along with the process in the plant. That is why the present paper addresses a previously unanalyzed variable on the effect of the discontinuity plane on the fragmentation results. From the numerical mathematical models applied through algorithms in advanced computational tools such as Elfen, it was quantified the improvement in fragmentation results as P80 through a correct pre-split plane both in its extension as well as in its width. The first results show an improvement of 30% in the P80 and ensuring the quality of the walls without damage to the matrix of the final wall. The basis developed in this paper is based on the concept of wave reflection in the free face zones where greater efforts are presented for fragmentation, a similar theory is presented in the variation of initiation sequences that seek a greater area of reflective planes in the form of "V". Cases were evaluated with a percentage of compliance of the pre-split planes from 0 to 100% evaluating the impact on the results and correlated with field information explaining the behavior and validating the benefit. From the quantification of the benefits, this work opens the possibility of focusing resources on optimizing the pre-split process to achieve an improvement in the fragmentation results, giving a greater tool in the decision to optimize the blasting process.

Feb 6, 2023

By Joshua Calnan, Braden Lusk, Kyle Perry

This paper presents detailed information and data regarding the load transfer characteristics of Blast Resistant Glazing Systems utilizing two different thicknesses of polycarbonate. A series of triaxial load cells, along with surrogates of identical stiffness characteristics, were placed around the glazing perimeter to directly measure the load transferred to the support system from explosions of varying degrees. The blast loads were developed using an explosive driven shock tube administered by the University of Kentucky Explosives Research Team (UKERT) in Georgetown, KY. Results presented include distribution of loading, maximum load transferred to connections, blast pressure-time data, glazing system deflection-time data, and final performance results of each system. The two glazing systems respond differently to the applied blast loading. Differences and similarities in the load transfer characteristics are discussed. The experimental results are then compared to a commonly used blast resistant glazing system analysis software tool utilizing a Single Degree of Freedom (SDOF) method of analysis for each system. Preliminary results show that currently used models do not correspond well with experimental data.

Jan 1, 2014

By Lizbeth A. Escobar, Phol M. Llanos, Maritza Y. Avila

The present research develops the estimation of critical parameters such as the distances and times between holes to avoid failure due to dynamic pressure in electronic detonators based on the near-field ground vibration model of Holmberg & Persson and the hydrodynamic model of Neyman.

Feb 1, 2020

By Clay McNail, Paul N. Worsey, John Schillie

"This paper is the result of undergraduate student research over the period of 2 semesters at UMR, which was focussed on developing a practical way to pneumatically stem horizontal boreholes, mostcommonly used underground. The majority of dry horizontal underground boreholes are pneumatically loaded with bulk ANFO. ANFO is preferred due to its low cost and the ease of pneumatic loading. However, stemming underground in the United States is a rare practice. In sharp contrast, stemming material (crushed stone or drill cuttings) is virtually always used in surface holes. The purpose of stemming is to increase blast efficiency by containing the explosive energy in the ground and to reduce environmental effects such as air-blast. The problem with stemming horizontal boreholes are; gravity cannot be used to load stemming material and the ANFO does not have a good interface due to problems with withdrawing the hose and the loading itself. This work follows on from Wilkins’ work on stemming angled boreholes."

Jan 1, 1999

By Ali Kahriman, D. Adiguzel, R. Ulger, U. Akkaya

The environmental problems arising from ground vibration has been faced and discussed frequently in various industries such as quarry, mining, civil works, shaft, tunneling, pipe line and dam construction etc. where the blasting operations are unavoidable. This paper presents the results of ground vibration analysis induced by blasting during the construction of the Istanbul Kadiköy-Kartal metro tunnel. Different rock formations in this tunnel route which is 21.6 km in length were encountered during the excavation process by blasting. As a first stage, Hoek’s Geological Strength Index (GSI) values of rock units were determined by using inverse distance weighting method. The GSI values which were obtained from boring data were used when evaluate the data. GSI values were estimated by inverse distance method (figure 3) along with the tunnel route. Afterwards, ground vibration parameters induced by 21 shots which were made in different locations was monitored and passing routes of vibration waves determined. Weighted averages of GSI values were calculated according to distance of the regions where vibration waves passed. Multi regression analyze were made with using frequency, charge per delay, GSI and the distance between the shot point and monitor station. The main goal of this study is to investigate the relationship between ground vibration frequency induced by blasting and GSI.

Jan 1, 2011

By Shadrack Nuamah, Erik Westman, Bright Afum, Jesse Addy

Rock fragmentation is the most critical aspect of hard rock production blasting due to its significant impact on drilling and blasting costs and the economics of subsequent loading, hauling, and crushing operations. This study analyzes current cost trends in the drill and blast operations of an anonymous open pit gold mine and proposes cost-effective drill and blast geometric parameters. The investigation focused on one operational pit with provided design parameters for two shots, shot 1 and shot 2. Existing blast parameters and two additional proposed sets of geometric parameters were evaluated using the Kuz-Ram and Chung and Katsabanis fragmentation models to estimate mean fragment sizes. The results indicated that the proposed blast parameters produced estimated mean fragment sizes within the mine’s desired range (not exceeding 45 cm). Additionally, the explosive energy was utilized efficiently per in-situ material blasted. The proposed parameters increased the estimated total volume of in-situ material fragmented by approximately 14% for both Shot 1 and Shot 2 compared to the current parameters. Furthermore, adopting the proposed blast parameters could lead to significant cost savings. The evaluated total drill and blast cost savings were approximately 11% for Shot 1 and 12% for Shot 2. These savings stem from the increased efficiency and effectiveness of the blast operations, highlighting the potential for substantial economic benefits. This study demonstrates that optimizing blast geometric parameters will allow open-pit mines to achieve desired fragmentation, utilize explosive energy more effectively, and realize considerable cost savings in drill and blast operations.

Jan 21, 2025

By John W. Brown

"Adequate dust control in and around rock drills is a problem that must be solvedfor the health and safety of workers running the drill as well as those working around thedrilling operation This paper will discuss the designs available from most drill manufacturers todayand the effort ‘nvolved in keeping them effective on a productive basis."

Jan 1, 1999

By Ronald W. Roberts

For years, blasters have experienced near-misses, injuries, and yes, even fatalities as a result of the dangerous nature of our business. Yet, some blasters continue to portray the immortal attitude: nothing-would-or-could-ever-happened-to me syndrome. As we all know, that attitude can become disastrous to yourself or colleague(s).

Jan 1, 1996