Search Documents

By Tristan Worsey, Nathan Rouse

Florida is one of the major limestone producing states in the United States. The state has unique regional geology and groundwater characteristics that require equally unique mining methods to extract limestone for construction materials. In many regions, aggregates quarries operate by drilling and blasting underwater limestone and then digging the muck with large draglines, while in others, mining operations are able to operate above the water table.

Jan 1, 2019

By Yoshikazu Hirosaki

How big or small is the Japanese explosive market? Who are the major explosive customers? Is there any big construction project in which a large amount of explosives is expected? What is the future of the explosives industry in Japan? Is it true that there are no ANFO trucks? What is the licensing system for blasters? Is there any education system for blasters?

Jan 1, 2001

By Wilfred G. Comeao

Close-in blasting occurs every time the use o f explosives for excavation or demolition requires the surpassing of the commonly accepted cosmetic damage criteriain order to arrive at reasonable and practical explosive weights per delay. One of the many effective blast design procedures consists in establishing a reasonable charge weight per delay with respect to scale, geometry, costs, requirements and constraints of the project. Once this reasonable charge weight per delay is determined, it’s environmental effects have to be estimated with respect to the surroundings.

Jan 1, 1991

By Dennis R. Jr Bell

Before beginning any site development or mineral extraction activity, it has been well documented that it is first prudent to gain an understanding of the prevailing geologic conditions.Whether it’s identifying the depth to type of bedrock, or determining the quality and quantity of the in place mineral deposit, these factors should always be considered in a project’s fatal flaw analysis. In situations where there is limited subsurface information, geologic models have been proven to be one of the most valuable and cost-effective tools used by the developer and/or his consultant.

Jan 1, 1997

By Dale Preece, C. Mick Lownds

Detonation delay timing has been an important aspect of quality rock blasting for decades. Detonators that enable delay timing have improved over the years especially with the recent advent of precision electronic detonators. The positive effects of precision delay timing have been observed repeatedly in the field with improved fragmentation, heave and overall blast control.

Jan 1, 2008

By Stephen H. Chung

The blasting performances identified above are considered to be the most practical ones for judging the effectiveness of a design combining explosives / rock / drill pattern. In a total blast design process, productivity relates closely to both fragmentation and heave / displacement of muck. In cast blasting, the more overburden displaced by explosives, the less blasted material there is left to be removed with mechanical equipment such as draglines or trucks. For wall protection and dilution control, estimates of the maximum extent of cracks / damage generated in situ due to blasting will help determine the location for drilling and loading perimeter blastholes.

Jan 1, 1994

By Calvin Konya, Anthony Konya

State and Federal construction specifications require the Blasting Contractor to prepare a Master Blasting Plan which is reviewed by the Owner’s Representative. The Master Blasting Plan requires the Contractor to submit the design of a typical blast. Most blasting specifications also require the Blasting Contractor to submit Daily Blasting Plans. The Master Blasting Plan and the Daily Blasting Plan require that the Blasting Contractor also submit the types and quantities of explosives and initiators used. The specifications also request that the Blasting Contractor submit the pounds of explosive used per delay for both production and presplit blasts. The Blasting Contractor may also be required to predict the anticipated ground vibration and air overpressure levels for the proposed blasts. There are equations that can be used to predict the ground vibration. There are also equations that can be used to predict the air overpressure levels. The data for these equations were primarily derived from quarry and surface coal mine and some construction blasts. Data from major construction projects were analyzed in this study to determine new air overpressure propagation equations for construction blasting. These new prediction equations compare calculated results analyzed from field data with other existing air overpressure prediction equations. Production blasting air overpressure values are also compared to air overpressure from presplitting

Jan 1, 2015

By Steve Dillingham

Today, a typical blaster is likely to wear many hats, including, but not limited to, supervisor, risk manager, safety coordinator, explosives engineer, communicator, as well as professional decision maker. Simply put, a blaster in the new millennium is an all encompassing blast site manager. As you know, accidents on the blast site can range from blast crew injuries to blasting incidents resulting from vibration, flyrock, misfires, etc. Not surprising, the incidents can quite often be traced back to direct preventable human action on the blast site. They can, however, frequently be avoided, if responsibly identified early and managed properly by an efficient blast site manager. Your company cannot afford to simply employ blasters; good blast site managers are necessary to produce the safest results possible.

Jan 1, 2001

By Craig Wilbour, John Stimberis, Rob Gibson, Lee Redden

An avalanche is a snow slide. A simple explanation is that the snow on a slope will slide (avalanche) when the snow strength can no longer support its own weight. Snow avalanches happen when the load from snowfall or ram on a snow slope increases faster than the stre n g t h of the bonds between snow crystals. Avalanches can also happen when the strength of a buried layer decre a s e s . Active avalanche control is the intentional triggering of slides. Washington State Department of Tr a n s p o r t a t i o n (WSDOT), does avalanche control to minimize the chance of natural avalanches into traffic. Avalanche control work is done all over the world by: highway departments, ski resorts, railroads, mining operations, utility companies, and other activities threatened by avalanches. The majority of active avalanche control is done with skis, by explosives, or exploding projectiles. Blasting techniques and practices have evolved to fit the specific needs of avalanche contro l . Passive avalanche control is the use of engineered s t r u c t u res such as snow sheds, bridges, or snow supporting devices, to permanently protect a specific location from avalanches. The problem is that these struct u res are extremely expensive. There are a variety of passive avalanche control measures as well as the active m e a s u res used to protect the highway over Snoqualmie Pass. As traffic volume and use expectations incre a s e , m o re extensive passive measures will be needed to keep avalanches from affecting the highway.

Jan 1, 2004

By AJ Rorke, JD Botes

Presplit blasting in strip mines is aimed at creating a safer wall to work under during the coaling operations. Good quality presplits are also necessary for effective throw blasting and drainage of the blast block. A less obvious but important function is full coal recovery. Optimum Colliery has been experiencing rock freezing against the presplit highwalls. The rock formed in patches along the highwall and trapped coal beneath it. The material that was &ozen comprised the rock between the back row of holes and the presplit and was often up to 3 m thick (the stand off distance between the back line and the presplit). The cozen rock formed predominantly along the bottom halfor bottom two thirds of the highwall. Along the top portion of the highwall, the presplit crack was usually well formed with visible barrels. This problem, or similar variations of it, is common on many South African strip-mine operations. Investigative work was carried out at Optimum Colliery to correct the problem. This paper presents the information and measurements that were made and discusses the solutions that have been applied to solve the problem. It was found that there were two independent causes for the tiozen material, with each contributing more or less to the frozen rock along the highwall. It was found that the presplit was not forming properly in places, especially closer to the bottom of the highwalls. The reasons and the solutions are presented. The second cause was found to be associated with reduced detonation velocity in the back line holes coupled with low confinement from long delay periods. Emulsion explosive that is sensitised with air bubbles was found to be prone to this phenomenon near the back of high-energy blasts. A change in the explosive formulation in the back-line holes, together with reduced delays in the back line, has resulted in significant improvements. The details are presented in this paper.

Jan 1, 2000

By Quentin Rhoton

To benefit two endangered fish species, waterfowl and other wildlife, and water quality in the lake and downstream, the decision was made to remove levees that had been in place since the 1950s. Because the levee material was mainly dredged up lake bottom peat, it was decided to pare down the sites chosen for breaching with dozers and trackhoes. This material was spread out onsite instead of expensive removal by dumping elsewhere. Because of the instability of the final pared down levees and the lake level being at a ten-year low, it was decided to use explosives to breach four of the sites. After over five months of earthmoving and two weeks of loading holes, the levees were detonated the day before Halloween, 2007. Somehow pumpkins showed up to be part of the explosive activities.

Jan 1, 2009

By Richard R. Marston, Scott Herr, Steve Pries, Donald L. Jr Ewart

The purpose of this paper is to identify and examine alternative methods (other than shovel/truck stripping) of effecting the pre-stripping of consolidated overburden, in conjunction with dragline stripping operations, at surface coal mines. The analysis will be case study oriented with practical mining considerations and comparative economics being evaluated. Alternatives that will be examined include blast casting, dozer push, and multiple pass dragline sequences.

Jan 1, 1992

By Mark A. Williams, James D. Humphrey

Without question, draglines are one if not the most effective tools available to the surface mining industry for overburden handling. With few moving parts and a two- or threeman crew, this machine silently sits and chews into millions of yards of overburden annually. A 100 cubic yard machine operating for 30 years will excavate three-quarters of a billion yards of material during that time. That is 750,000,OOO yards of material!

Jan 1, 1990

By Randal Martin

Recently, questions regarding the influence of atmospheric temperature and humidity levels on airblast levels have arisen at a number of blast sites. Humidity is alleged to have contributed to high levels of disturbance within communities surrounding blasting. In some cases, local regulatory agencies considered adopting guidelines to specify humidity and temperature ranges under which blasting cannot take place. However, it is normal blasting industry practice not to consider humidity or temperature effects, in the absence of inversions, on airblast levels. When blasting is conducted in the vicinity of residential structures, the influence of weather on the propagation and attenuation of airborne noise from the blasting site is always a concern. Sound naturally attenuates in air with distance from the source. A part of this attenuation is attributed to divergence at the airblast wave front, while the remainder of the attenuation is an accumulation of various factors that include temperature and barometric pressure, absorption in air due precipitation and vegetation, wind and temperature gradients, atmospheric turbulence and topography (Beranek, 1971). Wind speed and wind direction, as well as vertical and horizontal temperature gradients can cause airblasts to focus in local regions surrounding blasting operations and may result in air pressures greater than expected. In fact, wind and temperature inversions can actually increase sound levels with distance from the blast site. Close to the blast site, the effects of inversions may be negligible but may exceed 10 dB at 800 m or greater (Davis and Cornwell, 1991).

Jan 1, 2001

By Narendra Gupta, Gaurav Srivastava, Abhinav Sharma

From the days when plain detonators and safety fuse were used for initiation of commercial explosives, the commercial blasting and mining industries have made rapid strides. With the advent of electronic detonators in the late ‘90s, the face of commercial blasting was changed forever. The Mining Industry in India initially took a while to embrace Electronic Blasting Systems (EBS), however, more recently the industry has taken to EBS in a big way.

Jan 1, 2015

By Randall M. Wheeler

The purpose of this workshop is to illustrate how computer software can be used to evaluate blast design timing and simulate probable vibration characteristics. The workshop will be presented in two parts. Part I will cover the COMPU-BLAST Blast Design and Timing Analysis Program. Part II will focus on the ALPHA-BUST Vibration Analysis and Waveform Simulation Program. The information presented in the workshop will show how these two programs can be used together to help plan blast designs and aid in the control of vibration effects.

Jan 1, 1991

By Martti Hagfors

Underwater explosions have been used as a test method for the determination of energy content of explosives for several decades. This is the only test method by which shock, gas heave and total energy values can be measured separately. The experimental data can be measured from the pressure-time curves measured by the pressure-recording unit. The shock energy is integrated from the shock peak area and the gas heave energy is calculated from the time interval between the primary shock wave front and the shock wave caused by the first bubble implosion. tb. Bubble period, tb, is the time of first bubble oscillation, the time which passes after the shock peak front to the first bubble peak. The total energy value is the sum of these two partial energies.

Jan 1, 2009

By Deane Tunaley, Clint Brearley, Steven Kotsonis, Richard Goodridge, Tom Smylie

Explosives are widely used in the Oil & Gas Industry for subsurface mapping via measurement of reflected sound waves as each charge is detonated. To complete a seismic survey, several thousand explosive charges may be deployed into narrow boreholes, often in areas difficult to access or where socio-political factors may increase the risk of unlawful recovery or sabotage of the explosives. Therefore, when misfires occur, the explosives left in the ground often cannot be retrieved or sympathetically detonated safely, in which case they are “abandoned” (in-line with local regulations) potentially posing a safety and security risk.

Jan 1, 2014

By Neal Lee, Braden T. Lusk, Brendan McCray

Determining the minimum amount of inert material that can be used between explosive columns is a complex problem. Using too little inert material can result in detonator/primer failure, either by sympathetic detonation of or failure to fire of the subsequent explosive column(s). Propagation type failure results when inert material length between charges is small enough that the subsequent (delayed) deck fires more or less instantly. In this situation, the primer, detonator, or bulk product is initiated by the shock wave from the earlier firing deck. This type of failure may be un-noticed until the vibration/airblast report is examined.

Jan 1, 2016

By P J. Dailey, S L. Burchell, R F. Chiappetta

In recent years, high-speed motion picture photography has become a powerful diagnostic tool and technique to study, analyze, evaluate, and aid in blast designs. Production blasting, typically lasting less than two seconds, requires an extended time base for observation and clarification of short-lived phenomena. Information obtained from high-speed photographic analysis is categorized into two main groups.

Jan 1, 1989