Search Documents

By David Leidel, James Stuart

The 50 ohm resistorized electric detonator is commonly used in the oilfield for initiation of wireline conveyed perforating guns and other downhole explosive tools. This type of electric detonator provides some degree of safety above that of the conventional one ohm electric detonator, since a higher current level is required to initiate the device. In order to obtain the necessary data to develop safe distance tables from RF sources for the 50 ohm electric detonator, laboratory tests were conducted to determine the detonator’s “no-fire” current, AC impedance, and its susceptibility to ESD. The results were surprising as two types of failure modes were observed. The “no-fire’ current levels determined from Langlie “One-Shot” Test Methods were determined for the devices tested providing values for the 0.999 probability “no-fire” power level at a 95% confidence level. This data will serve as the basis for sets of safe distance tables from RF sources that will appear in the forthcoming edition of the Institute of Makers of Explosives Safety Library Publication 20, “Safety Guide for the Prevention of Radio Frequency Radiation Hazards in the Use of Commercial Electric Detonators, (Blasting Caps)”.

Jan 1, 2010

By Kirstin Girdner, Vicki Seppala, Tom BoBo, John Kemeny, Mike Higgins

Optimal blast fragmentation is fundamental to all phases of comminution. Changes in blast design may affect efficiency and productivity of downstream processes such as crushing, milling and leaching, resulting in cost savings or losses.

Jan 1, 1999

By Dennis A. Clark, Richard E. Calvin

As the scarcity of mineral resources increase and subsurface mining activities expand along with simultaneous surface mining in coal, industrial minerals and rocks, along with metals, the need to insure safe conditions is paramount.

Jan 1, 1981

By Riaan Van Wyk, Gys Landman

In today’s mining environment the use of radio communications in the form of two-way radios, cellular phones and even automated mining, form a vital part of the daily operations of a mining site. The radio transmissions that are used are a form of energy and as with all other types of energy it can have an influence on blasting equipment.

Jan 1, 2011

By Türker Hüdaverdi, Özge Akyildiz

"Efficiency of blast operations depends on fragmentation, overbreak, muckpile profile anddisplacement, vibration, airblast, flyrock and damage to wall or slope stability. To provide all these conditions at the optimal level, determination of rock mass properties (in-situ block size, joint spacing and orientation) is the very first step during design stage of rock blasting. Image analysis software is used not only to determine the fragmentation level of muckpile but also to characterize the bench face. In this study, an image analysis software was used to determine apparent block size of bench face and to measure blast fragmentation of muckpile. The source of errors and the vital points to be taken into consideration were explained for bench face characterization andfragmentation measurement. Since it provides much better results than previous techniques and it is not intrusive to production process, image analysis technique is considered as one of the most efficient and preferred way for fragmentation analysis. Besides these advantages, there are some weak points of image analysis software. Lighting is one of the most important factors for photographs captured for in-situ block size analysis and fragmentation analysis. Lighting determines shadow formation. In an ideal image, particles are clearly delineated by soft shadows. If shadows are too strong (dark), analysis suffers. Appropriate scale should be replaced onto blast muckpile during site measurements. The location of the scale in image affects the results of analysis. Also, the densityand orientation of discontinuities should be considered during application of image analysis technique to characterize bench faces. In this study, image analysis software was applied in thesandstone, limestone quarries of Istanbul region and an open pit boron mine. All image analysis, evaluations and results were made based on the site measurements."

Jan 1, 2017

By Split Engineering Chile Fernando Fernandez

Mathematical modeling in conjunction with mineral characterization is widely used as a method for design and optimization of comminution circuits, to simulate the processes of crushing, grinding and classification. An important input parameter to the simulation models is the Run-of-Mine Particle Size Distribution (ROM PSD). The run-of-mine size distributions due to blasting have a great influence on the performance of a semi-autogenous grinding (SAG) mill. In this paper, a mine case study was conducted where there are four primary geologic units and the material properties between the four units vary considerably. Also, the mixture of the four unit that will be mined at any given time also vary considerably. This presents a challenge in terms of optimizing the blasting for mill production throughout the mine life. As part of the case study, field rock mass characterization, laboratory rock mechanics tests, and laboratory breakage tests were conducted. The field characterization and rock mechanics tests provide material properties used to simulate the effect of different blast designs on run of mine particle size distributions (ROM PSD). The JKSimBlast software was used for these simulations. The rock breakage tests provide material properties used to simulate crushing and grinding performance. The JKSimMet software was used for these simulations.

Jan 1, 2015

By Michael S. Wieland

The work-principle method was developed for theoretically resolving toxic fumes from non-ideal charge formulations. The whole description of a wanted process refers to macroscopic changes resulting from removing and imposing constraints that work one at a time to chronologically render trajectory terminal (key) states. The trajectory resolution utilizes a thermodynamic quasi-potential or negative work function, and numeric results require some appropriate standard thermodynamic (equilibrium) reaction code TDRC. The underlying method is unable to restrict reactions, tailor the work output or resolve states within the trajectory transitions, so the trajectory terminology is used somewhat figuratively. The work-principle model has the working fluid (reaction material) interacting with a tremendous reservoir (chamber air and walls), while forecasting the work performed upon a mechanical agent.

Jan 1, 1998

By Bob de Raadt

The main problem in blasting a fly-over spanning a main road is the brief time available for blasting and the removal of the debris, in order to minimize the ensuing traffic disruption in the public highway below. The blasting plan is consequently based on an extreme "time is money" concept, in which speed and public safety are predominant factors. This paper discusses reliable blasting parameters for this type of demolition.

Jan 1, 1984

By E. Contestabile, B von Roser

Schedule IV containers in Canada and IME- containers in the United States have made possible the transport of mixed loads. That is, using these containers for detonators, one can simultaneously transport detonators and explosives on the same vehicle. As a result of a recent accident, the Canadian Chief Inspector of Explosives asked for a review of the appropriateness of the Schedule IV container in its present use. The Canadian Authority asked for a re-assessment of the adequacy of the Schedule IV container in preventing propagation of a reaction from the detonators in the container to the remainder of the explosives on the truck, and its ability to contain fragments generated by the detonators. A series of tests was performed to determine the initiation threshold temperature for non-electric detonators and the failure threshold temperature for the shock tube to establish some guidelines for preventing communication from one case of detonators to another within the transport container at elevated temperature. Tests fell into the following categories: inter-case sympathetic detonation, detonator thermal auto-initiation, shock tube thermal sensitivity, and intra-case sympathetic detonation. The results indicate that temperature is a critical factor, which determines to what extent, if any, communication occurs.

Jan 1, 2002

By NA NA

None

Feb 6, 2023

By Daniel Castelo, Ben Potter

This paper will discuss the most efficient and effective way to use shape charges when considering standoff distances and the amount of an explosive to be used. For each shape charge test that was performed, a one inch diameter copper liner of 90o was used. Different standoffs for each shape charge were tested to see which one would penetrate the deepest into rolled homogenous armor steel (RHC 44). It was determined that a standoff of three cone diameters provides the deepest penetration. In addition to testing for optimal standoff distances, the effects of overfilling as well as under filling a shape charge with explosive was tested against a shape charge with the bare minimum amount of explosive for correct detonation. These “fill” tests were all performed at a standoff of three cone diameters. Overfilling has little to no effect towards penetrating deeper into a target while under filling a shape charge has an effect of shorter penetration. C-4 explosive was the main explosive for all shape charges.

Jan 1, 2011

By P Cotton, N Cox

The Brisbane City Council has implemented a program of continual improvement at its Mount Coot-tha Quarry in the heart of Brisbane, Australia. The program has been underway for the past 6 years, and has resulted in very significant improvements in terms of both the cost effectiveness of its operation, and in terms of its environmental impact on nearby residents. The work has included a focus, amongst other things, on blasting efficiency, and has challenged conventional thinking in terms of the size of blasts fired, the frequency of firing, the diameter of blastholes, and the use of bulk emulsion or slurry explosives.

Jan 1, 1995

By D T. Froedge

A new system for acquiring blast vibration data and a method for presenting that data in such a way that there can be an extraordinarily enhanced insight into the understanding of vibrations produced by blasting is described in this paper.

Jan 1, 1989

By Gerald R. Coonan

Laboratory research is being conducted to substantiate suggested levels for voluntary standards on human response to transient vibration. The application of those findings to actual field conditions, however, will be limited because they will not include social and psychological factors existent in the real world. It is necessary, therefore, to examine available empirical information on complaints in an attempt to define the influence social and psychological factors might have on the laboratory results.

Jan 1, 1982

By Thomas L. Barkley

This paper describes an unusual design for a 12 foot diameter, 30 foot deep circular shaft shot in a close in urban environment less than 100 feet from occupied structures. It uses diagrams, video footage, and vibration results to describe a 3 deck, 17 hole burn round used to pull 17 feet in one lift.

Jan 1, 1994

By Pat McLaughlin, J R. (Dick) Daniels

Current practice in establishing quarries in remote areas with hilly or mountainous terrain tends to the use of airtracs (or similar pioneering units) drilling horizontal holes to establish a face, followed by bench development with light excavating equipment. The authors propose the use of a hybrid coyote blast design that incorporates long-round tunneling techniques. This method would, in effect, use down-the-hole (DTH) drills to advance the drift cut to the final depth, allowing longer and more rapid drift advances, and replace the cross-cut drifts with clusters of DTH holes to achieve the same explosives distribution.

Jan 1, 1995

Blast performance is related to rock structure and strength, as well as to factors such as site geometry, drill patterns, explosives loading, firing sequences and delays.

Jan 1, 1986

By Paul Worsey, Attila Szucs, Mark F. C. Schmidt

The use of water stemming with small explosive charges has been successfully developed at the University of Missouri-Rolla. Further study has been started to explore additional applications and uses for water stemming. Work has been focused in the areas of rock excavation and perimeter blasting techniques. This ongoing work is being conducted internally as graduate and undergraduate level research. A paper describing the general technique for use with boulder fragmentation was published in last year’s proceedings. The excavation work took place in the form of both small bench and trench shots while pre-split and trim shots comprised the perimeter-blasting portion. The excavation work was located in both the Roubidoux sandstone formation and the Jefferson City dolomite formation. Hole diameters ranged in size from 1.5” to 3” diameter and powder factors ranged from l/l 0 to l/3 of the conventional charge weight. The water was used to both couple the explosive charge with the surrounding borehole, as well as stemming. No other stemming material or products were used. The method of using water stemming in perimeter blasting was found to work well. However, when used for excavation purposes, adequate rock movement was not obtained. The rock was often split, but not fragmented. The airblast was surprisingly low, but the ground vibrations were excessive. This is not the case with trim shots, and therefore this method appears ideal for splitting purposes, especially in areas where people do not like to stem the tops of the holes, and where airblast and vibrations are of concern. Water coupling dramatically increases splitting and fracturing. However, fragmentation is not only fracturing but also the movement and swelling of the material. As the charge weights are reduced with this method, sufficient gas volume is not created to cause this necessary movement and swell, which is critical in rock excavation. This explains why its successful application was limited to perimeter blasting applications.

Jan 1, 2000

By Thomas A. Simpson, Yung-Kwaun Jow, Dennis L. Gamble

Construction of the $200 million Riverchase Galleria Mall in Hoover, Alabama was started in early 1984. The construction area consists of about 70 acres. The extensive building complex requires heavy concrete foundations which have to be poured during the early stages of construction and on a nearly daily situation so that contractual agreements can be met on a timely basis.

Jan 1, 1985

By Raymond V. Adolphson

The introduction of a new explosive component in 1955-56, called ANFO, featured much safer, effective blasting characteristics when compared to dynamite, accompanied by a notable reduction in cost. These savings mounted as borehole diameter or depth was increased with ANFO volume subsequently enlarged.

Jan 1, 1983