Search Documents

By Leslie Taylor, W. L. Fourney, Uli Leiste

Over the past few years, our laboratory has been investigating the loading on vehicles due to the detonation of buried explosives. We have been using target plates to represent the bottom of the vehicles that were being subject to the forces from the detonating explosives. Parameters shown to be important in the blast loading were type of soil, stand off distance (distance from the surface of the soil to the bottom of the target plate), and depth of burial (distance of the charge center of gravity to the sand surface). We conducted over the first year of our work a large number of tests which looked at the impulse being applied to the plates as a function of depth of burial, stand off distance, and type of soil. Of the three parameters we found stand off distance to be most important, depth of burial to be the next most important parameter, with type of soil least important. We also found that impulse could be scaled with explosive size quite accurately and that results (for impulse) were quite repeatable from one test to the next.

Jan 1, 2008

By Frank Lucca

This study is based on a six month study performed for Lee County, Florida. The study was based on blasting for land development and how this type of blasting affects structures. The study is investigates peak particle velocities and the relationship to other environmental and manmade forces that affect structures. The study also explores the effect of geology on blast vibration. After completion in Lee County, the study was then continued in the quarry environment in Vermont and extremely tight blasting environment of New York City. Charge diameters were 127mm (5 inches) or less.

Jan 1, 2006

By Michael Wieland

Sharp transient stress waves generated during the delay blasting of underground coal can damage unfired borehole charges remaining in the delay pattern. These tremendous stress pulses in coal bear a strong resemblance to underwater shock waves, despite differences in rise times, damping rates, and scaling relations. "Shock wave" terminology is adopted to distinguish the sharp transient waveforms propagating through the coal from the gas-driven stresses that rift the coal. Reported waveform characteristics of shock waves through underground coal were utilized to design a simulator test for rating the impact resistance of cap-sensitive explosives. Theoretical minimum borehole separations were determined for each cap-sensitive explosive from the requirement that worst-case waves hitting an unfired charge would not exceed its impact resistance rating. Rugged explosives have higher impact resistance and will function properly at smaller borehole separations. Additional work is required to verify the findings from the simulator technique and modeling relations reported here.

Jan 1, 1990

By Gary Anderson, J. P. Remi Proulx

Rio Tinto’s Colowyo Coal Mine produces 2.1 million tons per year in northwest Colorado. Colowyo uses the terrace mining method to recover up to seven coal seams ranging in thickness from 5 to 20 feet. Coal recovery in the 6 foot thick high grade C-seam has recently been challenged due to large variations in the pitch and roll of the seam. As well, some coal damage was seen due to an increased thickness of the overburden consisting of a hard sandstone channel.

Jan 1, 2012

By Maria Sullivan

There have been many papers and articles presented over the last 60 years questioning the relevance of the 8-millisecond blasting delay window as an ‘Industry rule of thumb’. The concept of using delays between blast holes to minimise vibration is well understood and agreed upon. The means for evaluating what that minimum delay interval needs to be, for a particular site given their ground conditions, design parameters and blasting techniques, is much less established. Some sites haven’t even recognised their required minimum delay value may not be 8-milliseconds!

Feb 6, 2023

By Thomas F. Mechtenberg, Michael S. Powell

In the past several years many coal operators and stone producers have reduced drilling and blasting cost by utilizing Bulk Emulsion/ANFO blends. For many operators the cost of equipment to handle blend products has been a major consideration in evaluating overall cost effectiveness of changing from packaged products or bulk ANFO to blends. This is especially true when the project length is short term or is uncertain.

Jan 1, 1990

By Brian Wingfield, Rick Givens, Greg Williams

Many technological advancements have been made in explosive products and applications over the last 15 years resulting in productivity and cost gains. However, the application of total energy (engine horsepower) in the majority of rotary drilling technology, has remained virtually unchanged over that period. While advancements have been made in components, efficiency, and types of hydraulic systems used on drills, the application of current hydraulic technology to improve drilling productivity has not been interactive with end users.

Jan 1, 1996

By B de Raadt

After discussing mechanisms of collapse for the explosive demolition of towers in general and cooling towers in particular, author comments upon a blasting operation in which four cooling towers were involved. The intention of this paper is to present reliable parameters, generally valid for the explosive demolition of reinforced concrete cooling towers.

Jan 1, 1978

By Walter Jr Duke

The security of explosive materials is a vital concern to every mine, quarry and contractor engaged in blasting. Proper construction of magazines and sufficient locking mechanisms are the fundamental means of maintaining secure storage. The object of this paper is to review the proper methods of construction of storage facilities for explosives as defined by the Alcohol, Tobacco, and Firearms regulations. Subpart K subsection 55.208 and the Institute of Makers of Explosives recommendations.

Jan 1, 1991

By Philip M. E Thomas

For over sixty years man has struggled to defeat the natural swamp lands known as the Florida Everglades as demand for land to support the burgeoning population growth in the state continued almost unchecked. Over the past ten years there has been a growing awareness that this land development could wipe out a whole ecosystem in a very short time unless steps were taken to reverse the trends. In 1991, a state law called the Marjory Stoneman Douglas Everglades Protection Act was enacted giving power to the South Florida Water Management Board to condemn certain lands for conversion to manmade swamp lands, designed to filter polluting run-off water from the agricultural lands around Lake Ockeechobee.

Jan 1, 1994

By Gimtong Teowee

SDI has launched the Electronic Detonator Blasting System containing a set of robust serial protocol and hardware exhibiting great ease in field usability and deployment. Programmable delay time with increments of 1 ms up to 10s is possible with excellent timing accuracy. Bus length of up to 2 km containing 1600 EIMs can be employed. A key feature of the SDI Electronic Blasting System has been its high tolerance towards current leakage in the bus line.

Jan 1, 2007

By Ruilin Yang

This paper presents a fragmentation model for large production blasts. The model uses peak particle velocity (PPV) induced from the blast as a controlling parameter to predict the fragmentation size distribution. The PPV can be related to shock pressure or strain under a given rock condition. The fragmentation size is calculated at three-dimensional grid points within the blast volume. The grid size defines the calculation resolution of the model. The fragment size distribution is assumed to be in the same form as the crack distribution within a cube (of the size equals to the grid size) surrounding a grid point. The crack distribution in rock from impact is based on the finding from previous researchers (Seaman et al., 1976). The fines and oversized blocks are calculated explicitly. The summation of the size distribution at all calculation grid points over a specified volume of the blast yields an overall size distribution for the volume.

Jan 1, 2015

By A. Torrance

A better understanding of the detonation performance of an explosive charge can be gained by directly measuring pressure, temperature and velocity of detonation (VOD). This is particularly important with commercial explosives because their performance is directly influenced by the degree of confinement given by the borehole diameter and the surrounding rock mass. A project funded by the Australian Coal Association Research Program (ACARP) was initiated in early 2009 with the view to design and build cost effective prototype instrumentation to measure the relative differences in detonation pressures and temperatures of commercial mining explosives. The project’s primary focus was on low density explosives. Low density (also referred to as low shock) explosives have been available in various forms for nearly 20 years. Identifying the pressure release patterns of both conventional and low density explosives under different geotechnical conditions should provide the necessary information to both validate detonation codes and better define input parameters for breakage and fragmentation models. This paper gives a general description of the prototype instrumentation developed and reports on the results obtained to date in testing the proposed instrumentation in laboratory scale conditions.

Jan 1, 2011

By Robert L. Martin, Brian W. Stump, David P. Anderson, David Gross

In an attempt to better understand the impact that large mining shots will have on verifying compliance with the international, worldwide, Comprehensive Test Ban Treaty (CTBT, no nuclear explosion tests), a series of seismic and videographic experiments has been conducted during the past two years at the Black Thunder Coal Mine. Personnel from the mine and Los Alamos National Laboratory have cooperated closely to design and perform experiments to produce results with mutual benefit to both organizations. This paper will summarize our activities, highlighting the unique results of each.

Jan 1, 1997

By Ralph E. Burnham, J. Kelly Ratliff

"The words “dynamite,” “TNT,” “explosives,” and “blasting” typically cause the general public, andjurors, apprehension and fear. Although blasting operations conducted by well-trained, skilled, andexperienced blasters rarely cause damage or injury, the public’s perception of blasting is that it isdangerous, disruptive, and results in damage to nearby properties. As a result, blasting operations have always resulted in complaints, claims, and lawsuits. However, in recent years, the public perception combined with an increase in public opposition, social media, more stringent regulations, predatory plaintiffs’ attorneys, and the application of strict liability to blasting claims has resulted in an increased threat of litigation to blasting companies and individual blasters. Consequently, many blasting companies find themselves receiving more complaints, involved in more litigation, and facing an alarming number of frivolous claims, which can result in increased insurance costs and other financial tolls. Accordingly, today’s blasting companies must be prepared for litigation and take steps to eliminate accidents and claims before the first shot is detonated on a job. The best way to accomplish this is standard operating procedures that incorporate best management practices, industry standards, and regulations in daily operations. This paper outlines some of the considerations that a blasting company should incorporate into its standard operating procedures before, during, and after the shot."

Jan 1, 2016

By John L. Floyd

The use of explosive energy to displace overburden or waste material can provide substantial savings to operations which normally rely on mechanical means for material removal. To optimize the available explosive energy, it is important to quantify the rock's response to the type of explosive and explosive accessories used. During a blast, rock breakage and movement occur so rapidly that the naked eye cannot detect the details of the fragmentation process. A relatively high speed motion picture camera (500 frames per second) can provide the extended time base needed to analyze in detail the site-specific rock response to the explosive detonation. The data of importance to blast casting that can be quantified from these films includes initial face movement, trajectory of rock, and differential face velocities of the material shot. In addition, the ground swell velocities, stemming confinement, and stemming ejection velocity can be determined. The performance of explosive products and delay element accuracy can also be ascertained. The use of high speed motion picture photography and analysis can reduce the number of field trials necessary to maximize explosive performance and increase the benefit provided by blast casting, and in turn, lower production costs. This paper will discuss the methods used for data accumulation and analysis. In addition, three field studies conducted at three separate mining operations will be presented.

Jan 1, 1988

The breakage mechnism of a spherical charge greatly differs from that of the cylindrical charge used in underground mining. The advantages of the spherical charge could not be utilized until INCO Metals Company, Ontario Division, introduced large diameter holes to their operation.

Jan 1, 1978

By Thomas M. Keevin, Gregory L. Hempen

A user-friendly model for environmental effects from underwater explosions is presently available. The model by Munday et al. (1986) is effective for determining fish mortality radii from underwater shooting. The IBLAST program (Coastline Environmental Services 1986) from this model includes estimates for both borehole-loaded explosives for demolition or rock removal purposes and midwater shots. Midwater shots may be used for fish population assessments or some seismic surveys. The program produces approximate mortality distances for planning purposes. IBLAST does have serious shortcomings of which users should be aware.

Jan 1, 1995

By Charles E. Joachim

Railroad and blast induced vibrations were measured in the vicinity of the proposed Big Bend Cutoff. Peak horizontal and vertical particle velocity relations were developed using least squares regression analysis. The dominant frequencies of these data are in the range of 30 to 50 hz. Therefore, allowable charge weight per 30 msec delay curves were generated for buildings (2 in./sec) and unlined tunnels (8 in./sec). A blasting contour map is presented for this site.

Jan 1, 1984

By Michael Swisdak, John Tatom, James Tancreto

In 2002, testing was proposed to generate needed data to assist in developing improved explosives safety standards within the US Department of Defense. This testing emphasizes two major areas: (1) full-scale donor/acceptor trials examining debris generation and acceptor response and (2) debris perforation testing of representative roof/wall materials. The full-scale donor/acceptor trials are referred to as the SciPan series. The first three tests in the SciPan series have been completed, as has the first phase of the SPIDER program. This paper describes the status and future of these testing programs, reasons for choosing specific tests, potential benefits, and planning for future phases.

Jan 1, 2006