Search Documents

By S. K. Chaulya, R. S. Singh, B. B. Dhar

Two prominent local species, Dendrocalmus strictus (bamboo) and Saccharum spontaneum (kashi), and two exotic species, Cymbopogon citratus (lemon grass) and Vetiveria zizanoides (vetiver), were selected for growth trials on dumps at Mandaman, Chora, Mudidih, South Balanda and Ghugus. The climate at these sites is dry tropical and the surface soil layer a slightly acid to neutral sandy to clayey loam 10-11 cm thick, impoverished in major plant nutrients. After two years bamboo had grown the most, up to 325 cm in height, and contributed the greatest biomass, 638 g/m2 of plant. The local kashi species had a very good regenerative capacity, which was lacking in the lemon grass and vetiver. The grasses had very good soil-binding capacity and could also provide income if used as cash crops

Jun 21, 1905

By T. F. Bamber

The South Nottinghamshire Area has not been greatly troubled by spontaneous combustion until the last few years, during which the Blackshale Seam has been developed and exploited. The problem was first encountered at a colliery which was heavily preoccupied with a major reconstruction scheme, and with the sudden appearance of a completely new hazard both men and management had to adapt themselves very quickly to meet the situation. The paper contributed to the Symposium by the South Nottinghamshire Area illustrates the problems by reference to actual incidents, and shows how the lessons learned from them have been applied to the shaping of future policy on the avoidance and treatment of spontaneous combustion.

May 23, 1905

By W. R. Chambers

A wide variety of mining conditions exists within the South Midlands Area and across this range of conditions more than one half of the mines are highly susceptible to spontaneous combustion. Two thick seams in which the greatest risk exists are described and illustrated. The different heatings which take place are categorized by the locations at which they occur in the mines: additional special cases not easily categorized by location are discussed separately. The discussion for each category of heating follows the pattern of: (i) the reasons why it occurs; (ii) when it arises the means by which it is fought, and (iii) the preventive measures taken in an attempt to avoid its occurrence. Relatively new factors which may affect the incidence of heatings are highlighted and suggestions are made which may assist in reducing the number of incidents in the Area. A new method of continuous sampling, analysis and recording is described and mention made of an original method of interpreting carbon monoxide results with the aid of the computer. The first results from this work show that an early warning is given of an adverse change in trend several weeks earlier than with the present methods. Lastly, suggestions are made about the direction in which research might proceed to assist in reducing the special hazards created by several features inherent in the present methods of mining.

May 23, 1905

Two of the most important economies in coal-washing are in the actual washing of the coal and in a proper lay-out to reduce to a minimum the cost of labour for handling and washing. A guarantee is usually required for turning out a washed coal containing not more than 2% of free dirt and a resulting refuse with not more than 2% of free coal; any plant that gives results within such guarantees can he considered economical, provided that there are no other losses during the washing process. Various drainage arrangements and washery lay-outs are illustrated and discussed with respect to drainage, bunkers, sieves, settling tanks and conveyors and two further points considered: siding accommodation, which may become quite important with washeries of large capacity especially when the coal is brought in railway-wagons; and the irregularity with which the coal arrives. (Paper presented at the Manchester Geological and Mining Society's general meeting held in Manchester, April 11th 1916, with Mr. Leonard R. Fletcher, President, in the chair)

Dec 1, 1916

By M. L. Schmulian

"The Windarra nickel deposits display many of the characteristics that typify Archaean volcanic peridotite-associated nickel sulphide ores of Western Australia. The Fe-Ni-Cu sulphide mineralization, which comprises dominantly disseminated sulphides, occurs at the base of a differentiated ultramafic volcanic pile grading upwards from massive meta-peridotitic flows to thin, locally spinifex-textured meta-picritic units. The entire mafic-ultramafic belt has been subjected to mid-amphibolite- facies metamorphism. The ore-bearing ultramafic is immediately underlain by dominantly sulphide-facies banded iron formation (BIF), which commonly contains nickel sulphides adjacent to its contact with mineralized ultramafic. BIF-hosted ores are formed both by physical remobilization of ultramafic-hosted sulphides and by migration of Ni and Cu into pre-existing iron sulphides.At Mt. Windarra the mineralization comprises eight steeply dipping, steeply plunging elongate oreshoots, which display a marked parallelism with major and minor fold structures in the underlying BIF. Seven of the shoots occur at or close to the base of the ultramafic pile, and are hosted by at least three overlapping flows. The zone of overlap occurs at the northern end of each flow, where picritic ultramafic, representing a dominantly liquid portion of the flow, occupies the basal contact. A gross south- north ultramafic flow direction is inferred. The eighth shoot occurs in a stratigraphically higher position within the ultramafic sequence.At South Windarra at least two overlapping mineralized flows occupy the basal contact, the ore zone having a strike extent three to four times its downdip extent. There is no obvious structural control to the mineralization."

Jan 1, 1984

By W. R. Donaghue, R. L. Robinson, C. Scott

Whilst spontaneous combustion has never been considered a major problem in south Durham, certain collieries in the area have a history of heatings and precautions are essential. Three collieries are affected - Shotton, Vane Tempest and Seaham - and in the case of the last two, there are huge areas of high quality coal to work under conditions where spontaneous combustion is a real hazard. The seam being extracted has an immediate roof in goaf left by the incomplete extraction of a contiguous seam worked before the turn of the century. The presence of residual coal stocks and old roadways and cavities adds to the difficulty of preventing unwanted air movement. The main preventive measures adopted are the construction of airtight gateside packs and the use of sprayed surface coatings in the gate. Sampling systems and sampling points are described and, in particular the field of continuous monitoring from the surface is examined. The resulting possibility of a quantitative as well as qualitative assessment of the preventative measures required is discussed.

May 23, 1905

By G. G. Lambert

The paper traces the pattern of spontaneous combustion in the workings of what was originally Hemsworth Colliery, but since July 1967 is now part of South Kirby Colliery. Examination is made of the Barnsley Seam sections and the part played by the top section of the seam as it comes in close proximity to the main seam. In this area of the colliery nine mechanised faces were set away between the years 1953 and 1968, every one "fired" at the pillar edge and six "fired" at the face line when production had ceased. The paper deals with the different preventative measures used, from sandbag walls, cement injections, spraying with polyurethane, until finally using Mandoseal as a sealant. Since the latter method was first used, the last three faces worked in this particular area were all salvaged completely, without any sign of a heating developing.

May 23, 1905

By A. Policard

The bodies of mammals possess a very efficient mechanism for ridding themselves of inhaled dust. When the lung is healthy this mechanism works very well, and dust is quickly and completely expelled from the lung either by the respiratory tract or the lymphatics. The mechanism, however, is easily upset, and slight alterations in the condition of the ciliated epithelium or the circulation of lymph are sufficient to interfere with it, therefore the second mechanism comes into play and the dust is fixed and immobilized in some part of the lung. This, however, is not a real cleansing process, since the lung becomes a dust-trap, and may become'pneumokoniotic. The mechanism is protective at first, but later, when the accumulation of dust is considerable, it gives rise to trouble. The lung cannot become, so to speak, a physiological dust-trap, and still retain its normal structure and function; pneumokoniosis begins, which is essentially a disease due to the mechanical presence of large amounts of inert foreign material.

Jan 1, 1947

By A. C. Dunham, Y. D. Drakapoulos, P. W. Scott

The Pt and Pd occur alloyed with copper in small, irregularly-shaped grains, 0.25-5.0 micrometers in maximum dimensions. Grains of unalloyed native copper are also present. The grains are completely surrounded by or marginal to magnetite with inclusions of Ni-Fe-Co sulphides and native Ni-Fe, which is apparently a product of the serpentinisation process. Crystallisation of the Pt-Pd-enriched copper probably occurred at the same time, at low temperature, but the previous form of the Pt and Pd is unknown as no earlier PGE phases have been found. While Pt and Pd minerals are usually important in early-magmatic base-metal sulphides, Pt alloyed with Cu is extremely rare and apparently occurs only very late in the paragenetic sequence. A Cu alloy with Pd dominant over Pt and only minor amounts of other elements appears not to have been reported

Jun 14, 1905

The mineralogical composition of the ore was determined and the mineral phases with which nickel is associated were identified. The ore was prepared by grinding to -420 micrometres and classification into granulometric fractions. Prior to the main series of experiments the effect of agitation rate on nickel recovery was investigated. The influence of sulphuric acid concentration, temperature and particle size on the kinetics of nickel extraction was then studied, both quantitatively and qualitatively, over fixed value intervals. Application of the initial rate method enabled determination both of the order of reaction with respect to sulphuric acid concentration and the activation energy for the dissolution of nickel. The results indicate that a physical mechanism can be ruled out as the rate-determining step in the extraction of nickel from the ore and that a chemical mechanism is more likely

Dec 1, 1991

By L. J. Barnes, R. O. Koch, J. H. Versteegh, P. J. H. Scheeren, F. J. Janssen

Following two years of laboratory research with bench scale reactors, a 9 m3 experimental process demonstration reactor was installed at Budelco's zinc refinery to treat their underlying groundwater. A 600-fold scale-up was successfully achieved. It has demonstrated that this anaerobic microbial process can remove a wide range of heavy metals and sulphate to the required levels. Extended operation of the demonstration unit has shown that the process is robust, can withstand wide variations in feed composition, rapidly recovers from operational upsets and is easy to start up and shut down. The metal sludge produced can be processed in a metal refinery to recover both metals and sulphur.

Jan 12, 1992

By D G. Oldfield

Pall has developed and supplied to several airlines cabin air libers to provide clean air for passengers and crew in flight, while reducing airline operating costs. Most of today's modern commercial passenger aircrafts employ cabin air recirculation as a means of reducing operating costs. With large numbers of passengers being subject to an increasing proportion of recirculated air for hours at a time, the matter of cabin air quality, with particular respect to the health effects on passengers and crew, has to be addressed. Commercial pressure will ensure that the airlines and aircraft manufacturers will not revert back to the total fresh air systems of the 1960s and 1970s. In fact, feasibility studies are already being undertaken to look at increasing the proportion of recirculated air to 80% and above. With the application of specialist nitration technologies. Pall is able to ensure that the requirements for economy are met whilst ensuring that the air is effectively rendered as 'fresh air’ each time it is recirculated.

Jan 9, 1996

By V. E. Ross

A comparison was made of three methods for determining the contributions of true flotation and entrainment during batch flotation tests. In the first method size-by-size recoveries are measured in both the presence and the absence of a collector, a frother being present in both tests. In the second method the mass of solids and water recovered after a chosen time of flotation is varied by changing the rate of froth removal and the depth of the froth. The third method uses a transfer factor to describe the classification of solids and water, and hence the changes in the composition of the pulp, during a single flotation test. Batch flotation tests were carried out with artificial mixtures of pyrite and gangue, the amount of floated material recovered being calculated according to each of the three methods. The discrepancies betweeen the calculated amounts are analysed in terms of the assumptions that are made for the various methods and the most suitable conditions for the application of each method are identified

Dec 1, 1991

By J. R. Hammond, I. C. Herbert

Report of discussion at October, 1970, IMM general meeting (Chairman: M. J. Cahalan, President) and contributed remarks on the paper published in Transactions/Section C (Mineral Processing & Extractive Metallurgy), vol. 79, June, 1970, pp. C128-36 and introduced by I.C. Herbert. Contributors were von Struve G., on the application of balling discs and the use of basic additives; Young P.A., asking for details of the drying, grinding, balling, induration and specification testing equipment and processes; Davison J. on pellet swelling properties and Carter G.C. on disc operation, refractories and green ball properties.

Dec 1, 1971

By R. Trueman, D. B. Tyler

Numerical modelling was used to determine the magnitude and direction of stresses around drives both adjacent to and distant from open stopes in the South Crofty tin mine. Modelling predicted that drives near the stopes are situated in a stress-relaxed zone. The peripheries of drives that are sited in solid rock away from the influence of stoping are in compression. Key-block modelling was used to determine the typical geometries of critical blocks and distinct element modelling was used to determine block stability. The conclusions derived from modelling fitted the observational data. This indicated that key-block theory is a valid tool for analysing the stability of roadways in the South Crofty mine. The support requirements for drives located next to stoped-out areas were formulated using a risk analysis approach to key-block formation. The results were compared with support guidelines derived using empirical design methods. Good agreement was obtained for the roofs of the drives but not for the sidewalls. The concept of a critical excavation width was formulated: once an excavation is larger than the critical size the length of rockbolts need not be increased as the excavtion dimensions increase. This may be the case in all rock mases.

Jan 4, 1993

Discussion of the paper presented at the North Staffordshire Institute of Mining and Mechanical Engineers' general meeting held in Stoke-on-Trent, March 27th 1916, with Mr. John Gregory, President, in the chair, included contributions by Gregory J., Cadman J., Hartley J.W., Wain E.B. and Henshaw A.M., followed by the author's reply

Dec 1, 1916

Discussion continuing that published in Trans.I.MIn.E ., 1915, vol.L, p.449 and 1916, vol.LI, p.166, included contributions by Smith W., McLaren R., Gibson J., McCreath W., Sneddon J.B., Kirkpatrick J. and Mowat D.M. and a written response by Black J.N.

Dec 1, 1916

By A. G. Waters, N. J. Bristow

A comparative study was made of an untreated and a heated haematite ore and a sinter produced from a feed consisting of 100% ore, to study the influence on reduction behaviour of sinter bonding phases such as SFCA (silico-ferrite of calcium and alumina). Under low-temperature reduction conditions the order of increasing reducibility followed that of increasing porosity and surface area but under similar conditions at 900 degrees C the sinter exhibited higher reducibility than the ores even though the total porosity and chemical reducibility of the individual phases were lower. This behaviour can be explained in terms of the higher total porosity of the natural ore at low temperatures and the higher level of fine pores in the sinter at high temperatures due to the presence of SFCA, which acts to support the fine (c.0.1 micrometre) pores created by the reduction process. This leads to the conclusion that the main role of SFCA in sinter during high-temperature reduction is to maintain a high level of fine porosity. Some implications of this work for granule design and sintering practice are discussed

Apr 1, 1991

By L. Wade, R. Wang, M. A. Horton

Laboratory methods to find the mechanical properties of rock are inherently biased towards stronger strata, which best survive the sample preparation process. Geophysical techniques are not subject to such bias and may be used to predict mechanical properties rapidly and cheaply. Samples (151) were obtained from a borehole that had been comprehensively geophysically logged. The mechanical properties of the samples were established in the laboratory and correlated with the geophysical responses of the strata from which they came. The results indicate that, for homogeneous strata at least, it is possible to predict the unconfined compressive strength reasonably well from sonic travel time measurements made in the field. Predictions of static Young's modulus may also be made from this data source, but with a lesser degree of confidence. A multivariate regression equation is presented which relates down-hole sonic travel time to unconfined compressive strength, depth and the frequency of fractures in the rock mass. This equation may offer potential for the prediction of the mechanical rock properties of fractured and layered strata.

Jan 4, 1993

By A. B. Holland-Batt

Two graphical techniques which are commonly used to assess batch separations are analysed in terms of reaction kinetics to provide a more powerful method of evaluation. An alternative and more general approach, based on the selection and application of suitable efficiency criteria, is also presented. The method proposed distinguishes between selection and collection efficiency in flotation and can be used to estimate the degree of liberation in the feed. Two examples are given: table concentration of monazite and ilmenite from a beach sand, and flotation of a pyrite-haematite ore

Dec 1, 1971