Search Documents

By B. Rezai

Impeller speed and air flow rate are two influence parameters on coarse particles flotation and collision and attachment angles. So, in this research recovery of quartz particles at four diameter classes carried out and collision and attachment angles investigated. It is found that maximum flotation response was observed at Impeller speed of 1100 rpm and 15 L/h air flow rate. For either more quiescent (Impeller speed<1100 rpm) or more turbulent conditions, flotation recovery decreased steadily. Furthermore, amount of attachment probabilities is calculated using suitable equation. According to this study, with decreasing particle size, air flow rate and impeller speed, probability of attachment increased and with increasing contact angle, probability of attachment increased. For various air flow rates, impeller speed and particle size, collision angle has been calculated. Maximum collision angle obtained at with 15 L/h air flow rate, particle size of 256 µm and impeller speed of 700 rpm and minimum collision angle obtained at with 45 L/h air flow rate, particle size of 545µm and impeller speed of 1300 rpm. In this study, maximum attachment angle, , was around 75 L/h air flow rate, particle size of 256 µm, contact angle of and impeller speed of 1300 rpm and minimum attachment angle was with 15 L/h air flow rate, particle size of 545 µm, contact angle of and impeller speed of 1300 rpm. ?82.72 ?64 cr??33.39 ?90 ?13.0 ?60

Jan 1, 2014

By A. V. Bogdanovich, S. A. Urnysheva

"Gravity and X-ray luminescent separation methods are generally used in processing of diamond ores. X-ray luminescent separators are applied for separation of diamonds from feed ore size fractions from 100 to 10-15 mm size and for final treatment of gravity concentrates over 1 mm size. Gravity separation machines used for diamond ores separation are heavy medium cyclones and pneumatic jigs. One of the most important parameters, to a large extent affecting diamonds recovery from ore, as well as processing costs and specific energy costs, is size of dumped final tailings. That was exactly the purpose of the studies, the results of which are described in this paper. The studies performed on different ores showed that in order to achieve high recovery results, it is necessary to dump heavy medium separation tailings below 3 mm size. Separation of final tailings of -6+1 mm size by jigging is also possible. However, with a view to exclude extra diamond losses, it is necessary to maintain jigging concentrate yield approximately at 25% from starting feed, with its subsequent cleaning in heavy medium cyclones. In addition to that, it is necessary to separate 20-25% of middling with diamonds content at feed ore level and subject it to grinding. This will complicate flow sheet, but reduce load on heavy medium cyclones. In order to develop optimal flow sheet for gravity concentration of a specific diamond ore, large-scale investigations are required, including technical-and-economic assessment of separation alternatives. INTRODUCTION In processing of diamond ores, gravity and X-ray luminescent separation methods are generally used. It is common practice to apply X-ray luminescent separators for separation of diamonds from feed ore size fractions from 50 (100) to 20 (10) mm size and for final treatment of gravity concentrates over 1 mm size. With that, X-ray luminescent separation tailings larger than 3-6 mm size are reground and delivered to gravity concentration processing stage. Middling products circulation volumes are large, not infrequently necessitating decrease in concentrating plants capacity, especially with mining in deep workings of deposits, where ore strength is higher (Goryachev, 2010; Vaginov, 2000; William, 1988). Diamond ores preparation before processing is accomplished by means of roll-screw crushers and autogenous grinding mills, minimizing probability of free diamonds damage in liberation from barren rock. In re-crushing of size fractions that are “difficult” in autogenous grinding, high pressure grinding rollers are applied (Burchardt, 2014; Fedotov, 2011a, 2006b)."

Jan 1, 2018

By V. A. Luganov

The processing of pyrite concentrates may be accomplished with a preliminary enrichment due to withdrawal of iron sulfides from initial concentrate. The withdrawal of iron sulfides is possible with the help of magnetic separation when the magnetic iron sulfides (pyrrhotites) separate from non-magnetic fraction?the sulfides of non-ferrous metals. The conversion of non-magnetic pyrite to magnetic pyrrhotites of adjusted structure occurs because of roasting with the withdrawal a part of sulfur. The resultant pyrrhotites are strong ferromagnetic with hexagonal structure. This paper contains results of studying magnetic properties of pyrrhotites, findings of the de-composition of initial pyrite with the consequence homogenizing of product and hardening of product of decomposition in liquid nitrogen. Define the type of pyrrhotites super lattice structure, was established that at increasing of sulfur contention the magnetic properties of pyrrhotites are change ? pyrrhotite begin evince the properties of antiferromagnetic material and magnetic susceptibility of material is interruptive changing from 0 to 1.7×10-3~1.9×10-3 SI units/g system. The paper contains results of technological researching of pyrrhotizing-magnetizing roasting of pyrite concentrates in different condition: in unoxidizing, with the decreasing contention of oxygen and in autogenous regime in air atmosphere. Established that the magnetic susceptibility of products depend of pyrite degree dissociation and achieve 2×10-3~3×10-3 SI units/g system at 40%~45% desulphurization. Defined the conditions of steady regime autogenous roasting, at resultant products possess coefficient of magnetization, and this can be used magnetic separation for separating ferromagnetic pyrrhotites from gangues and non-magnetic sulfides of non-ferrous metals. This technology of pyrrhotizing roasting is recommended for effecting in industrial condition. The initial materials and products of roasting subjected to chemical, thermogravimetric, Moss-bauer spectroscopy and X-ray analysis, defined the magnetic properties.

Jan 1, 2014

By Xin Tan

In this paper, two types of low-grade complex zinc oxide ores (sandstone and limestone ores) from Yunnan province, China were investigated. A large number of argillaceous and alkaline gangue makes it infeasible to treat the ores with heap leaching. Although wet metallurgy can be considered, the lower efficiency of liquid-solid separation, the high cost, and low revenue limit this technology to be put into practice in large-scale. In order to solve this problem, a new technology combining mineral processing method with metallurgy technique is studied to process this refractory ore that consists of sandstone ore with 5.84 per centZn and limestone ore with 6.50 per centZn. The results of the tests showed that zinc can effectively be recovered from two types of the ores by using the new technology, and the acid consumption can be remarkably reduced. For sandstone sample, 82.96 per cent Zn was recovered by flotation and final Zn recovery by flotation+ hydro-metallurgy can be up to 78.17 per cent from the ore. In addition, for sandstone, acid consumption can be reduced from 270kg/t by direct acid, leaching to 76.92kg/t by flotation + hydrometallurgy combination. For limestone sample, 85.90 per centZn was recovered by flotation and totally 80.95 per cent Zn can be recovered by new technology which is a combination of mineral processing and metallurgy. Besides, H2SO4 consumption can be reduced from 450kg/t for sandstone originally to113.79kg/t after using new technology. One merit of this new process technology is that the zinc sulfides and oxides can be recovered without desliming in the flotation cells at the different stage and make sure the concentrate products as a good feed for hydrometallurgical technology. This study provided pretty good technical support for tapping low-grade refractory zinc oxide ores. Keywords: low-grade zinc oxide ores, limonite, non-desliming beneficiation, flotation + hydrometallurgy combination

Sep 1, 2012

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

By D. Y. Liang

Rare metal ores have those features of high industrial value and bad performance in ore separation. Most of rare metals ores are with low grade of valuable components, rareness of useful minerals, complicated combination of associated minerals and high difficulty in separation and enrichment of minerals. For those single (Ta, Nb) or (Ta, Nb, Sn) ore occurred in granite and pegmatite, the ways of gravity separation and magneto electric separation to concentrate (Ta, Nb) minerals are adopted. There are many mines being explored successfully both at home and aboard. While, for complex (Nb-Zr-REE) ores associated with Be and Ti minerals, they are commonly considered as rich rare metals ore but more difficult to process. One of rare metals mine in Inner Mongolia has the features as with large reserves and high grade of columbium and zirconium and accompanies with REE and beryllium, therefore with significant industrial value. After the utilization of research method of process mineralogy, detailed mineralogy research has been made on the rare metals ore. The test results show that there are abroad isomorphism replacements among such elements, such as Ti, Mn, Fe, Nb and Ta, between Be and REE in metallic oxide minerals of that ore, which makes the mineral composition of that ore extremely complicated. This research identifies clearly the mineral composition, and investigate at the technological property and the occurrence of those elements as Nb, Zr, Be and REE in the rare metal ore. The achievements of this research provide important mineralogy basis for ore dressing research of refractory rare metallic ores.

Jan 1, 2014

By Ritva Tuunila, Antti Häkkinen

"Wet stirred milling is one of the most effective grinding methods in producing very fine powders in large scale production, but it is a very energy-intensive process, especially when pigments or even nanosize particles are produced. Therefore, optimization of the process parameters is important. The specific energy consumption is a function of stress energy, which describes the effect of tip speed and media characteristics on grinding, and is related to the number of stress events during milling. In effective grinding, a large number of stress events are necessary. The stirrer configuration influences the number of stress events and their intensity, because the motion of the media and the suspension are caused by a rotating stirrer. The effect of three different stirrer types: a pin, disc and blade stirrer, on the grinding rate, i.e. product fineness and specific energy were investigated in this study with a batch laboratory stirred mill with two tip speeds. The material used in the experiments was calcium carbonate. The results obtained with the smaller tip speed showed approximately similar grinding rates and energy consumption for all stirrer types. When looking in closer detail, the blade stirrer seemed to give the finest product with all grinding times compared to the pin and disc stirrers, which both produced almost the same product fineness with the same grinding times. The specific energy consumption was the smallest with the disc stirrer, but not very big differences were obtained. With a higher tip speed, greater differences occurred both in grinding rates and specific energy consumption. The blade stirrer was the most effective in grinding, and the pin stirrer the next. The net energy consumption for the blade and pin stirrers was almost the same, but it was slightly higher for the disc stirrer."

Jan 1, 2014

By Zoran S. Markovic

The extensive laboratory investigations were carried out in order to determinate behavior of sulphide and nonsulphide copper bearing particles during the flotation. The present ore sample were contained 0.55% Cu with 20.1% of nonsulphide copper in it and gangue material with higher contents of alumina about 19.07%. In this paper will be presented some results such as: effect of particle size, pH and applied collectors. The main goal was in application of collectors S-7518, as well as mixture of KEX and Z-96. Z-96 is a product from Chemical Industry Zupa Krusevac which was used as auxiliary collector in mixture with xanthates. The best results were done with this mixture in ratio KEX / Z-96 as 77/23 % in area of oxidized minerals flotation, but the collector S-7518 was achieved better results in sulphide mineral flotation. The S-7518 has better selectivity between copper minerals and pyrite comparing to mixture of KEX/Z-96 in mentioned optimal ratio. Flotation recovery and copper grade in concentrate were studied by flotation kinetics tests.

Sep 1, 2012

During incineration of municipal solid waste (MSW), various environmentally harmful elements and heavy metals are liberated partly into bottom ash, and partly carried away with the off-gases and subsequently trapped in fly-ash. If these waste incineration residues are not properly processed and immobilized, it can lead to secondary environmental pollution to the air, soil and water. The stricter environmental regulations require a higher immobilization efficiency of the waste incineration residues, which is the main objective of the present cooperation research. Within the present project, a systematic scientific research on various MSWI residues has been carried out, including sampling, low or high temperature processing and leaching tests. In the present paper, the major results have been summarized. The research results reveal that through appropriate combined pre-processing and high temperature vitrification, the bottom ash and fly ash can be efficiently stabilized. The results achieved provide a valuable alternative route to treat the solid residues from incinerators, and to make efficient recycling and safe utilization possible.

Jan 1, 2014

By Lj. D. Andric

By the micronization-milling of the material, the size and the structure of its particles are changed and it comes to the increasing of the potential energy of the system as well as to the chem-ical activity of the material what is the result of an increased free surface and of the concentration of the grate defects, that is of the internal energy of the system. All these changes that are reached, show that new characteristics of treated materials are got by micronization process. Controlling the process of the micronization and by purpose directing of the new characteristics of the activated materials, we can have the positive effects and use them in more technologies. Talc is important nonmetallic mineral raw material that is widely used as either the basic raw material, or as filler. This has stimulated its technological investigation, as well as the investigation of its physical-chemical characteristics. In this paper are shown experimentally reached results of the physical-chemical characteristics of the talc during the process of the micronization in high energetic mill. In this paper, the optimum conditions of miconization of talc in high-energy-speed rotary mill and its influence micronization on a degree of Fe2O3recovery by hydrometallurgical methodes, are presented. The X-ray analysis of the obtained products showed that high quality talc with low content of can be obtained by these physical-chemical processes In this paper, the principles and application or fine and ultra-fine grinding high-energy attriton mill with small balls, enabling fast, efficient grinding, low energy consumption, short grinding time and easy handling will be described.

Jan 1, 2014

By X. Q. Cui

The surficial collapse pits of the mining areas are continuously spreading in Beiminghe iron mine of Hebei Province as a result of the exploitation, which has done a lot of damage to the circumjacent ecological environment of the mine. It is a new path to handle the mine tailings at the present time that the thickened tailings are used to backfill the collapse pits, in which way the problems of the surficial collapse and the nowhere discharge of the tailings are both solved, and the rational utilization of the mine tailings and the clean production of the mine enterprise are realized. The?200 mesh content of the tailings of Beiminghe iron mine is 76.87%, and?325 mesh content is 63.50%. Semi-industrial dehydration experiments to the tailings have been done using the hydro-cyclone classified thickening process. The results show that when FX125 hydrocyclone is adopted, the concentration of underflow can achieve 73.31%, and the yield ratio is 61.78%; when FX150 hydrocyclone is adopted, the concentration of underflow is 70.57%, and the yield ratio is 54.31%, which indicate that the minor diameter hydrocyclone is propitious to improve the yield ratio of the underflow. The semi-industrial dehydration system of hydrocyclone classified thickening process is com-posed of FX125 hydrocyclone, D3600 high-efficient thickener and D2000 thickening bucket. The capacity to tailings disposal can achieve 3.07t/h and the tailings can be thickened from 28.86% to 62.45%. Compared with the traditional thickening-filtrating process and the total tailings directly filtrating process, the hydrocyclone classified thickening process has the merits of simple flow and high thickening efficiency, so it is easy to be realized in the mine.

Jan 1, 2014

By W. Z. Yin

With increasing of mining depth, many iron ores in Liaoning Province contain carbonates such as siderite and ankerite. The emergence of these carbonates in ores creates a fatal impact on the running producing process of anionic reverse flotation in Dong Anshan Sintering Plant, which leads to ?concentrate and tailing no separated?. And its reason is still unknown. Moreover, siderite, despite that its ferric theoretic grade is only 48.2%, however, do not affect the blast furnace utilization factor, therefore, can be used as raw materials in ironmaking. In order to solve the separate problem of iron ore containing carbonates, five pure minerals, martite, magnetite, quartz, siderite and ankerite, were selected for a series single flotation experiment. The aim was to discover the flotation difference of these minerals, furthermore, to explore a new flow sheet for the iron ore containing carbonates. The results of single mineral flotation experiment reveal that the combination regulators, starch and CaCl2, in different pH extent, can make these minerals taking on obvious flotation difference, which make it possible to process the iron ore containing carbonates. A new flow sheet, step-flotation, to process iron ore containing carbonates is explored, that is, first step, direct-flotation processing, is to eliminate the bad effect that the carbonates bring in flotation system by collecting carbonates under neutral condition; the second step, reverse?flotation processing, is to get qualified iron concentrate by collecting quartz under alkaline condition. Manual mixed ore sample were processed successfully through this new flowsheet under proper reagent system, which has absolute advantage compared with routine flowsheet. Actual ore sample of compound magnetic separation concentrate were processed successfully both open and closed circuit experiment through this new flowsheet. SEM and EDS were used to probe the reason why carbonates affect the regular processing. It is analyzed that moderate floatability of siderite and its coating on the surface of hematite and quartz make the phenomenon ?concentrate and tailing no separated?. This research provides a reasonable processing scheme for iron ores containing carbonates and can be used for reference in processing other complicated, refractory iron ore.

Jan 1, 2014

By Sanchita Chakravarty, Sumantra Bhattacharya, Divya Jyoti, A. K. Mukherjee, Soni Jaiswal

"Release analysis is independent of collector and frother dosage and type, but it is primarily influenced by the degree of liberation or “state of release of the sample”. The shape of release curve is an indication of the degree of liberation. This paper briefs about the effect of reagent combination, particle size and surface characteristics on the release analysis of difficult-to-clean LVC coal.Release analysis of three LVC coal fines obtained from two different coalfields of India was carried out at three different size levels such as -0.5mm, (-0.5+0.1) mm, and -0.1mm. The collectors used were n-dodecane and commercial diesel oil. Incomplete liberation of coal fines even at a size of -100µm, corroborated by photomicrographs of ROM and clean coal macerals, in a great measure reduced the flotation-based cleaning potential of the fines. FESEM images of fines reveals that the adherence of ultrafine onto the surface of relatively coarser particles reduced the clean coal recovery. The results obtained also appear to be coal, reagent combination and, particle size and particle surface specific. Only one coal indicated the liberation as is usually expected for -0.1mm particles with a reasonable yield of 65% at 18% ash. INTRODUCTION Froth flotation has a long history of being used to treat coal fines. Coal flotation is considered to be difficult, if the percentage of Near Gravity Material (NGM), i.e. essentially locked particles, in flotation feed is >10% [Aplan, 1993], which is usually the case with all the coking coal fines in India. The fines are rich in vitrinite, so valuable for coking coal. Unfortunately, there appears to be no standard procedures to determine the separation efficiency of froth floatation. Release analysis proposed by C.C. Dell in 1953 [Dell, 1953], aimed to determine the ultimate floatability of coal. Several other techniques had been proposed but release analysis technique has been considered to be a vast improvement over the batch flotation process [Forrest et al. 1994]."

Jan 1, 2018

By B. Orberger, J. M. Milazzo, S. B. Blancher, J. Lützenkirchen, J. L. Dubos

"Industrial dusts are commonly agglomerated using empirical recipes with binders such as bentonite, while Sludges are agglomerated into mixes. Those materials contaminate the products, are expensive and generate significant amounts of slag. Achieving cold dust agglomeration with little or no binder requires understanding the controlling parameters in order to predict and optimize the process behavior. This in turn necessitates comprehensive dust characterization to base predictions on measurable characteristics. In the present work we collected 13 Mn-rich dusts over all the process chain: feed fines, smelting, and refining dusts, as well as ferromanganese alloy dust. This is the first systematic study of dusts along the Mn-processing chain for chemical, physical and mineralogical parameters. X-Ray Diffraction, Qemscan® and laser granulometry analyses show that the mineralogy, Particle Size Distribution (PSD) and morphology evolves from complex heterogenous to simple, homogenous along the process chain: The mineralogy of the primary ore dusts shows various hydroxides, oxides, carbonates, tectosilicates and phyllosilicates. The furnace dusts contain oxides, tectosilicates and carbonates with volatiles, while the refining dusts present only oxides and metal. Finally, the Metal dust is nearly pure metal. Particle morphologies and PSD vary from jagged, irregular particles with broad PSD (>1 mm to <0.3 µm) to smooth and spherical with narrow PSD (100 µm to <0.3 µm). The Metal dust is an exception with angular particles. The Cationic Exchange Capacities (CECs) of all samples range from 0 to 22 meq/100g. Specific surface areas (SSAs) range from <0.1 to 27m²/g, and seem to decrease with from ore feed to Metal dust. This may be due to the disappearance of hydrated and/or sheet-bearing minerals, since a smaller grain size usually implies an increased SSA. The zeta potential varies strongly over the range of the samples tested. However, beside the Gabon ore which has an Isoelectric Point (IEP) ~ 4.1, the other IEP ranges between 2 and 2.5."

Jan 1, 2018

"A sulfide ore containing 2.19 g/t Au and 13.13 g/t Ag was studied for the deportment and extractive metallurgy of pay metals. The ore is composed mainly of non-sulfide minerals with approximately 10% pyrite and minor amounts of marcasite, chalcopyrite, galena, sphalerite, and arsenopyrite. The deportment study using a comprehensive approach showed that gold and silver minerals in the ore are mainly native gold (Au), electrum (Ag, Au), petzite (Ag3AuTe2), hessite (Ag2Te) and volynskite (AgBiTe2) with minor amounts of acanthite (Ag2S) and argyrodite (Ag8GeS6). At current grinding fineness (P70@150µm), the majority of liberated native gold and electrum particles are larger than 20µm with 85% >40µm, some of them are even larger than 150µm, indicating that extended leach time may be required to dissolve these coarse gold grains to completion and gravity concentration needs to be considered. Petzite is relatively fine with all liberated particles being less than 80µm in size. Gold distribution and leach testwork results showed that liberated gold accounts for 50% of the head assay, exposed gold associated with sulfide and non-sulfide minerals accounts for 30% and 11% of the head assay, respectively. Gold locked in sulfide and non-sulfide accounts for 4.8% and 4.1%, respectively. Thus, it is recommended that cyanide leaching be considered for extracting gold in this ore. This paper presents the detailed results of the gold and silver deportment study and extractive metallurgy testwork, and discusses the impact on process selection and flowsheet development.INTRODUCTION Gold and silver have been found in various geological environments and ore types. In terms of the gold deportment and extractability, gold ores can be classified into two categories and 12 types. Their extractive metallurgy is largely driven by mineralogical factors such as particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals and locking of submicroscopic gold in sulfide and sulfarsenide mineral structures (Zhou et al., 2004; Marsden & House, 2006; Zhou, 2013a, 2013b). Compared to gold, silver mineralogy is more complex and metal extraction is more challenging due to its presence in over 200 Ag-bearing minerals (a silver-rich ore body would typically contain 5 to 10 different silver minerals) (Gasparrini, 1984), presence of refractory silver minerals (such as pyrargyrite, prustite and stephanite) and submicroscopic silver in sulphide minerals (such as galena and copper minerals) (Chryssoulis et al., 1985; Di Prisco et al., 2002). The presence of these issues often causes problems in Ag-bearing ore processing. Therefore, knowing the deportment of gold and silver in the ores and metallurgical products is important for flowsheet development and process optimization."

Jan 1, 2018

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By Jingzhong Kuang, Zheyu Huang, Chuanzhou Guo, Pengfei Liu

"In this paper, scheelite and scheelite coated with Pb2+ (SC) were synthesized by chemical precipitation with the help of ultrasonic. The role of the Pb2+ on scheelite was evaluated. Additionally, the dissolution behavior of minerals and the adsorption mechanism of collectors were investigated systematically via SEM, XRD, EDS. The results indicate that the ultrasonic cavitation can promote the formation of scheelite with large particle size and high crystallinity. Due to the exchange of WO4 2- and OH-, the dissolution of scheelite are not in a 1:1 equivalent amount by chemical formula and the concentration of WO4 2- is higher than that of Ca2+ in the solution because Pb2+ promotes the transfer of WO4 2- from scheelite surface into the solution. The dissolution of scheelite is an endothermic reaction and its enthalpy reaches the maximum value of 692.59J·mol-1 at pH=8~10. But the coating of Pb2+ changes the thermal effect of scheelite in the solution and the dissolution of SC is an exothermic reaction with the dissolution enthalpy of -262.30 J·mol-1. At pH=8~10, the adsorption capacity of sodium oleate and salicylhydroxamic acid on the surface of SC is higher than that of scheelite which delivers that Pb2+ contributes to the scheelite surface dissolution and enhances the adsorption of collectors on the mineral surface, thus achieving activation.INTRODUCTIONIn modern society, tungsten is a type of quite important rare metal and also a strategic resource. Because of its low vapor pressure, high melting point, good electrical and thermal conductivity properties, it is widely applied in high-temperature technology, lighting, machine and engine construction (Zhao,Z.W, 2013; Yan, W, 2017; Ilhan, S, 2013). Both scheelite and wolframite are the major tungsten deposits. With the depletion of easily-processed wolframite, scheelite has drawn a great deal of scientific and industrial attention. Scheelite can be recovered by flotation due to the metathesis of polarity and chargeability on minerals surface via adding regulators and collectors."

Jan 1, 2018

By S. Patra, R. Venugopal

"The quality of pellets produced is affected by quality anssastd quantity of green pellets, amount of addition of binders, type of binders added, amount of moisture added along with the other variables like rotation, inclination and fineness of feed. The green pellet quality depends upon chemistry, mineralogy and granulometry of fines used for pellet making, the feed size, its moisture content and porosity. During firing of green pellets ingredients present within reacts to form different phases and microstructure. So in turn physical and metallurgical properties of pellets are influenced by amount and type of binder and flux addition, induration time and temperature. During iron making process, the metallurgical properties of fired pellets are decided by the type and amount of these phases and their chemistry. Green pelletizing and induration studies have been already carried out with hematite ore fines. Indian iron ores of high alumina content showing different pelletizing characters, these studies can’t be directly interpreted. The main objective of proposed research work is to understand the green pelletizing process and determine the water bentonite interaction at different levels. Detailed investigation on swelling behavior of bentonite and microstructure of the green pellets of iron ore fines from SAIL captive iron ore fines from the Barsua in the state of Odisha. To convert these ore fines into pellets, the key raw material, additives and process variables that influence the pellet quality needs to be identified.INTRODUCTION Pelletization is the unit operation of agglomerating iron bearing fines (generally below 150µ with 65-80% passing 40µ) by tumbling in horizontal rotating drums or inclined discs, (Sivrikaya and Arol, 2013; Bhuiyan et al., 2011; Forsmo et al., 2006; Sastry et al., 2003) and the pellets are approximately spherical lumps formed by this process in presence of water and binder, on subsequent induration at 1300°c (Sivrikaya and Arol, 2014; Sivrikaya and Arol, 2013; Sivrikaya and Arol, 2012; Sivrikaya and Arol, 2010; Sastry et al., 2003; Kawatra and Ripke, 2003; Iveson, 2001a; Iveson, 2001b)."

Jan 1, 2018

By V. I. Ryaboy, I. V. Ryaboy, E. D. Shepeta

"The problem of separation of copper minerals and arsenopyrite remains relevant because of environmental requirements. The selective action of reagents with the thioamide group (thioamides) is known in iron sulfide’s flotation of pyrite and pyrrhotite. The aim of this study was to reduce the arsenic content in the copper concentrate when using thioamides by reducing the flotation of arsenopyrite in the flotation of the sulfide part of the skarn scheelite-sulfide ores. We have chosen the most widely used thioamides for the study, such as Z-200. We also synthesized new reagents with the thioamide group. The most selective and the most powerful thioamide copper collector were used for further studies. Reduction of arsenic content in copper concentrates is achieved in the following way: You need to apply a strong thioamide collector with a selective but weak dialkyldithiophosphate collector, or vice-versa, a selective, but a weak thioamide collector should be used with the dialkyldithiophosphate reagent with strong collective properties. The proposed combination presents industrial interest because of its accessibility. The application of thioamides in copper minerals and arsenopyrite selection has showed that these reagents have fewer selective properties than dialkyldithiophosphates. To achieve the comparable recovery of copper using dialkyldithiophosphates requires markedly greater consumption of thioamides, due to their lower hydrophobic ability. The application of a composition of thioamides and dialkyldithiophosphates allows to increase the recovery of copper and to obtain a lower arsenic content in copper concentrates compared to their individual use. The lowest arsenic content in the copper concentrate is obtained in the composition consisting of the newly synthesized thioamide with strong collective properties and selective dialkyldithiophosphate. The addition of even small amounts of xanthate to the composition of thioamides and dialkyldithiophosphates causes a sharp increase in the arsenic content in the copper concentrate without a notable increase in copper recovery."

Jan 1, 2018

This investigation addressed two products from Samarco?s desliming circuit, namely underflow of cleaning cyclones and underflow of desliming cyclones. The roughing cyclones receive the product of the grinding circuit. The underflow of the roughing cyclones feeds the cleaning cyclones and the overflow feeds the desliming cyclones. The underflows of cleaning and roughing cyclones are combined to constitute the feed of the flotation circuit. These fractions were characterized and a new process route was proposed. The size distributions of the two fractions are quite different. The desliming cyclones underflow presents higher amount of material passing 37 µm and of ultrafines as compared with the cleaning cyclones underflow. Laboratory scale flotation tests were performed in a mechanical machine aiming at comparing the performances of these products in the presence of the reagents employed in the concentrator. Pi-lot scale column flotation yielded enhanced iron recoveries for both products in comparison with those achieved in laboratory mechanical cells, without impairing the concentrate quality. The in-crease in recovery was more significant in the case of the cleaning cyclones underflow. These results suggest the use of columns in the flotation of this product aiming at increasing the overall iron recovery. Nevertheless the results also showed that the use of columns to float the cleaning cyclones underflow should also be taken into consideration. Despite the fact that this product requires a longer residence time in order that the required silica content in the concentrate is achieved, the indication is that higher levels of iron recoveries might be reached. The conclusion is that, due to the different behaviors of the two products, they should be processed in distinct circuits to maximize the iron recovery.

Jan 1, 2014