Search Documents

By Stefan Larsson, Jan Ekström, Jennie Kock-Larsen, Håkan Garin

"This paper describes the testing procedure (or protocols) for quality control of dry deep mixing columns in a major ground improvement project carried out in Sweden. Quality control was mainly based on column penetration tests performed at different stages in the project and on two occasions after installation. In the paper, the results from the tests are compared with tests on the unimproved clay. As expected, the results show that the correlation between undrained shear strength in the columns and in the unimproved soft soil depends mainly on the in-situ stress. However, the correlation probably depends on when the tests were performed after mixing. When the influence of the in-situ stress was excluded from the analysis, no significant correlation could be identified. This means that the undrained shear strength in the columns and in the unimproved soft can be considered to be uncorrelated when the strengths and the corresponding variability are evaluated with depth from groups of tests.INTRODUCTIONQuality control and quality assessment of deep mixing (QC/QA) constitute a key component in verification of the limit state design. Due to the complex mixing process and varying geological conditions, it is normally not possible to sufficiently assess the strength and deformation properties in advance. In Sweden, the most commonly used QC/QA method for verification of the limit state is the column penetration test (Axelsson and Larsson 2003; Bergman et al. 2013). The method works well but is time-consuming and requires many tests since property variability is normally high. The column penetration test can be used to assess the undrained shear strength Cu,col. However, it is not clear how the strength correlates to the undrained shear strength of the unimproved soil Cu,soil. There are common factors such as the in-situ stress state and the natural water content, which makes a positive correlation probable, i.e. as Cu,soil decreases, Cu,col also decreases and vice versa. The unimproved soil has a natural spatial variability, but it is not known if the improved soil follows the same variation. The mixing process has a substantial influence on the strength variability and may supersede the influence of other factors. However, if a sufficiently good correlation exists between Cu,col and Cu,soil, information from the geotechnical ground investigations can be used in the design and planning of QC/QA of deep mixing in a more stringent manner. Information about the correlation is also essential in reliability based design, where a strong positive correlation may have a negative influence on reliability. However, as discussed by Al-Naqshabandy and Larsson (2013), this correlation may be weak or insignificant for a representative failure domain where the mixing process may have a dominant influence on the strength variability. It is thus of interest to assess the correlation."

Jan 1, 2015

By Thomas D. Humbert, Christopher J. Ramsey

Construction of a new underground parking structure in State College, Pennsylvania, is situated on a site constrained by limited ROW and required excavations ranging in depth from 25 ft to 40 ft. Additional complications included busy surface streets, an active intersection, and numerous underground utilities that could not be disrupted by construction activities. To combat these challenges, an innovative approach for earth retention was designed that combined multiple types of retention systems. The overall system included alternating sections of soil nail walls and a hybrid system of soldier pile walls (consisting of micropiles) that were partially restrained by a soil nail wall in the lower portions of the excavation. Further, due to the limited space within the property limits that inhibited the length of the permanent nails, the wall design team collaborated with the project designers to develop a solution such that the completed wall became an integral part of the final design/construction of the underground parking structure. INTRODUCTION HERE at State College is a mixed-use, high-rise building in State College, Pennsylvania. The 12-strory building has up to 3 levels of below-grade parking, with the above-grade levels consisting of residential and commercial/retail space. The existing property was a parking lot bound by the streets Calder Way to the north, Garner Street to the east, East Beaver Avenue to the south, and Heister Street to the west. The overall property sloped approximately 20 ft in elevation from southeast to northwest. Excavation for the below-grade levels extended 21 ft to 36 ft (6.4 m to 11 m) below street level. During design-development phases of the project, it became evident that due to subsurface conditions and right-of- way limitations, conventional construction techniques would not be feasible. The full perimeter of the excavation would require earth retention including the weak shale bedrock along the bottom of the excavation. The project developer (CA Ventures) and general contractor (Brinkmann) coordinated with the specialty contractor and wall design engineer to find a solution. At this time, Coastal Drilling East (specialty contractor) and Wood Environment & Infrastructure Solutions (wall design engineer) became involved. The project developer and general contractor were aware they needed an earth retention system, but given the many variables the project faced, a single, straightforward solution would not work in this application.

Jan 1, 2019

By Garland Likins, Gray Mullins, George Piscsalko

"Quality control of drilled shafts is greatly dependent upon the practices of the site personnel. For drilled shafts cast under slurry, inspection of the hole prior to concreting is very difficult or impossible. There are numerous non-destructive test (NDT) methods currently available to assess the integrity of drilled shafts. This paper will discuss the theory and use of an emerging NDT technology known as Thermal Integrity Profiling (TIP). The Thermal Integrity Profiling method measures the elevated concrete temperatures that occur during the hydration process. These temperature measurements are made along the length of the pile and can determine the integrity over 100% of the pile cross section, both inside and outside the reinforcing cage. With the known shaft volume information, TIP can evaluate the effective shaft radius at each measurement location. With the increased use of TIP on highway projects, there is a need to have standard criteria for shaft acceptance. Shaft acceptance criteria can be based upon thermal measurements and subsequent analysis of the data to determine the average shaft radius, local concrete cover, and cage alignment. With this additional information obtained via the thermal testing method, acceptance methods based upon concrete cover can be developed. In this paper the Thermal Integrity Profiling method will be described, results from a case history will be discussed, and an acceptance criteria based upon concrete cover will be proposed.INTRODUCTIONDrilled shafts are an attractive foundation element in many applications due to their large axial and lateral capacities. When drilled shafts are cast in a dry hole, it is possible to inspect the hole prior to casting, allowing for very basic level of quality control, although the shape of the completed element is still unknown without some form of post construction testing. When drilled shafts are installed where soil conditions are unstable, the shafts will often be cast under slurry to support the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to impossible to accurately and efficiently inspect the hole prior to casting concrete and it is equally difficult or impossible to inspect the shaft during the casting process"

Jan 1, 2016

By Pancho J. Garza, Keith H. Dahlen, Chris A. Labye

"Design for reconstruction of the East Flagstaff traffic interchange project located in Flagstaff, Arizona posed particular challenges. The proposed design included construction of a nearly 50-foot tall mechanically stabilized earth (MSE) wall given rightof- way constraints and soft subgrade soils. The tight right-of-way, approximately 15 feet in certain locations, adjacent to existing structures limited the number of viable remedial alternatives to provide grade separation at the proposed bridge abutment without significant settlement. Preliminary analyses indicated the existing subgrade soils - consisting primarily of relatively soft silts and clays with decomposed pumice - would settle approximately 12 to 14 inches resulting in unacceptable wall deformation. Stone columns placed via vibratory methods (vibro-replacement) consisting of circular excavations which penetrate to firm bearing soils and which are filled with crushed stone were selected to densify the existing subgrade soils. The implemented mitigation measures helped limit settlement to less than one inch and allow for successful construction of the project. The project history - including site constraints, subsurface conditions, evaluation of remedial alternatives, stone columns methodology, and effectiveness of ground improvements - will be discussed.IntroductionThis paper describes the subsurface investigation performed for the reconstruction of the Business Route 40 (B-40) (Country Club Drive) and United States (US) 89 Traffic Interchange (TI) located within the city limits of Flagstaff, Arizona. This project is currently referred to as the East Flagstaff TI. The Project Site Vicinity Map is shown below.The former B-40/US 89 TI was considered ineffective in handling the current and projected volumes of traffic which transition from northbound (NB) B-40 to US 89 (both directions), as well as from southbound (SB) US 89 to SB B-40. The intent of the project was to reconstruct the TI to better accommodate projected traffic volumes. The project eliminated the existing ramps from both NB B-40 to SB and NB US 89. The new interchange includes a Tee intersection from B-40 to US 89. In order to accommodate this alignment, the profile of US 89 was raised several feet (on nearly the same as existing horizontal alignment) to match the elevated profile of B-40. B-40 was shifted just west of its current alignment to accommodate construction of a new, wider bridge structure which spans over Industrial Drive, the Burlington Northern Santa Fe (BNSF) railway, and old Route 66. South of the new bridge, B-40 transitioned back to the existing alignment just north of the I-40/B-40 TI. Within the project limits, both US 89 and B-40 were widened to three travel lanes in each direction."

Jan 1, 2015

By Hidekatsu Takeuchi, Masaru Sakakibara, Shigeo Tanabe, Kenji Harada, Akihiko Suzuki, Shoji Morihana

"Deep mixing (DM) method, one of the most commonly used solidification methods, is based on the principle of solidifying soft ground. It can be classified into two categories such as Cement Deep Mixing (CDM) method and Dry Jet Mixing (DJM) method which apply hardening agent in slurry condition and in powdery condition respectively. In recent years, DM methods have undergone changes that have evolved them from the traditional method to meet the needs of the diversifying market. Among them, the Contrivance-Innovation Clay Mixing Consolidation (CI-CMC) method is a DM method which mixes a cement-type hardening agent in slurry condition mechanically with soils in situ and incorporates the innovative technique, “atomized ejection” that has been developed to allow faster installation of larger diameter columns without sacrificing quality compared with conventional methods. At this technique, the atomized hardening agent is discharged together with compressed air through a device incorporated into the mixing blade. It also has advantages of performing the works with low-displacement of the surrounding soils in consideration of environmental friendliness and with higher penetration capability against hard ground.This paper presents the technological outline of the above-mentioned CI-CMC method, focusing on the atomized-ejection technique, followed by some construction examples, applied to the self-earth-retaining wall, to the hard ground and the area adjacent to the existing structures.INTRODUCTIONAccording to the accumulation of its case histories, Deep Mixing method has been receiving the demands of its application to more challenging conditions, such as harder ground condition, and requirement of lower displacement of the surrounding ground during its operation. In addition, to match its price against the other cheaper methods and widely receive its benefit of higher quality, the cost reduction of Deep Mixing is also one of the major challenges. For the cost reduction, higher productivity and lower consumption of the material to obtain the equivalent strength and homogeneity with the conventional method are required.The Contrivance-Innovation Clay Mixing Consolidation (CI-CMC) method has been developed to meet these demands. CI-CMC incorporates the mist ejection that has been developed to achieve faster installation of larger diameter columns without sacrificing quality compared with the existing methods. Normally, we obtain cement columns of about 1.0 m in diameter by using Deep Mixing method. To increase the productivity, it is not preferable to drastically increase the penetration and withdrawal speed of the mixing blades because of the hardness of the ground and restriction by minimum number of passage of rotating blades per a certain height of the soil cement. Instead, the expansion of diameter of the columns will simply increase the productivity. The development of the new mist ejection system, as shown in Photo 1, has enabled the diameter of soil cement columns to 2.0 m on single axis while 1.6 m on double axes. Mist ejection means that the hardening agent slurry is sprayed into the ground in mist form together with compressed air thereby achieving homogeneous mixing and reducing the resistance on rotating blades."

Jan 1, 2015

By William Billiet

"The Dulles Silver Line Phase II is an 11.4 mile extension of the Washington Area Metro Transit Authority’s Silver line in northern Virginia. There are three miles of elevated guideway, which are supported on 188 large diameter mono-shafts founded within the Triassic Geologic Aged Culpeper Fault Basin. Three lateral load tests were performed on fully instrumented test shafts. The challenge in developing the load testing program was how to reproduce the effects of the extremely high design loads along the test shafts, considering the limitations of the load test equipment. Development, execution, and analysis of the lateral load test program is discussed.INTRODUCTIONPlans for Dulles Silver Line Phase II include two Aerial Guideway sections on elevated track, the Main Line and Yard Leads. The Aerial Guideways are supported on mono-shafts (single, largediameter drilled shafts) socketed into rock. Lateral loads are resisted primarily through the stiffness of the shaft and the geotechnical resistance of the rock socket. The monoshafts were designed in accordance with AASHTO LRFD 2014. Based on our preliminary analyses, the production mono shafts were expected to consist of 6.5, 7.5, and 8.5 foot diameter drilled shafts with rock socket lengths varying between 8 and 34 feet (averaging 14 feet). Table 1 summarizes the maximum service load combinations for each size production shaft along the aerial guideway alignment.GEOLOGYThe project is located within the Piedmont Province, a major physiographic province on the east coast of the USA extending from Alabama to Pennsylvania. Within the Piedmont, a number of Mesozoic basins formed in rift valleys. Dulles Airport is located in the Culpeper Basin, characterized by a relatively shallow siltstone rock surface compared to the adjacent areas underlain by Piedmont crystalline rocks. The geologic stratigraphy at the load test sites generally consist of residual soils and intermediate geo-material (IGM) overlying siltstone rock. IGM is a term used by Virginia Department of Transportation (VDOT) to describe residual material as it transitions between soil and rock. For the purposes of the load test, the siltstone rock is classified as fractured rock (RQD<50), and competent rock (RQD=50). Table 2 summarizes the stratigraphy encountered at each test site."

Jan 1, 2017

By Lucie Spencer, Craig Butterworth

"This paper presents the design of a raft enhanced pile group recently constructed for a hotel development in Perth, WA. At the time of construction in 2016 the hotel was the tallest prefabricated hotel in Australia.The structure covers the entire 12 m by 32 m development footprint, located in an inner city environment, and directly surrounded by existing structures. The small site and lack of space required innovative thinking in terms of the substructure design.The ground conditions comprise a layer of medium dense sand underlain by variable layers of stiff clay, silts and sands. Groundwater was around 1.5 m below ground level.The substructure design was carried out on the basis of a raft enhanced pile group. This allowed the use of much shorter piles than a conventional pile solution, thereby permitting the adoption of CFA piling techniques. This also allowed the raft thickness to be reduced to such that the substructure works were maintained above the groundwater level.The design was carried out in general accordance with the Australian Standard AS 2159 and using conventional piled raft design techniques involving iteration between elastic soil settlement software and structural analysis software until spring reactions were obtained with convergence of the two models. Following this springs were introduced to model piles in the structure.Due to the variable nature of the ground and resulting uncertainty in pile base capacity it was not considered appropriate to design the system as a pile assisted raft with piles loaded beyond their ultimate geotechnical design strength. As a result, all piles were designed based on a maximum load maintained within the elastic response region, with the majority of the load taken by the piles. However, the combined capacity of the raft and the piles allowed for a saving in pile lengths and numbers of around 40%, when compared to a conventional pile group designed in accordance with the Australian Standard AS 2159.The raft slab was monitored during construction in order to check the actual displacements against the design displacements. At the end of construction, the settlements were found to be within 2 mm of the design values.INTRODUCTIONThe Wellington Street area of Perth in the CBD is undergoing recent regeneration which includes the King’s Square development, Perth Arena and the Wellington Street Bus Station. The proposed hotel development is close to the recent developments on a Lot previously occupied by a low rise development. Due to the small size and constrained nature of the site, the substructure design for the tower needed to take into account available space and the impact of the works on adjacent properties. This paper presents reasoning for the choice of substructure design, details of the design methodology adopted, results from limited post construction monitoring and potential improvements that could be considered for similar future developments."

Jan 1, 1900

By Chu E. Ho

This paper reviews the design of jet grouting at re-entrant corners of excavations where the diaphragm wall and secant pile wall installation were interrupted by existing utilities in the streel sidewalk. Jet grout blocks were formed to seal the gaps in the walls for excavation support, consisting of four to six columns in clusters. Jet grouting was performed around an electrical duct bank which had to be maintained. Jet grouting was executed through stratified soils using various combinations of jetting parameters for different soil strata. The installation sequence and age of the neighboring columns within a cluster will affect the jet’s ability to form subsequent columns. When jet cutting is limited next to hardened grout columns or embedded obstructions (such as diaphragm walls or secant pile walls in this case), the specific gravity (SG) of spoils would be reduced and tend toward the value of the injected grout SG. The magnitude of spoil SG is also influenced by the variability of the grout mix supplied. Specific Gravity Ratio (SGR) defined as the ratio of spoil SG to the actual grout SG at the time of jetting can be used as an indicator of successful treatment, with SGR > 1.0 indicating effective soil erosion. Verification coring and testing were implemented to confirm target column diameter and strength of grouted soils have been achieved.

May 1, 2022

By Tomio Tsuchiya

A construction method of bored steel H piles enclosed in soil-cement columns was developed by modifying steel H piles from the driven pile method and soil-cement walls from the earth retaining wall method, the latter of which produces cut-off walls and reduces noise and vibration during construction. In this method, as shown in Figure 1, rich mix cement paste is injected into the bottom of a borehole which is pre-excavated by a casing auger, then a steel H beam is inserted before it hardens. Since the high vertical resistance of piles created with this method has already been confirmed by loading tests, we have been investigating the applicability of this method for piles used to temporarily support building loads for top-down construction on raft foundations until the raft foundation is completed. However, in the loading tests, the bearing capacity at the lower end of the pile was measured by loading from ground surface on test piles which had friction cut to eliminate the shaft friction resistance. In other words, the loading tests neglected the effect of overburden pressure of soil above the lower end of the pile. To investigate the effect of the overburden pressure on the bearing capacity at the lower end of the pile, loading tests were carried out on a bored steel H pile of lm diameter (test pile) bored in a compacted sandy soil layer with N-value of 100 to 250 at each stage of a three-step excavation. The results show no significant change in the bearing capacity at the lower end of the pile when the depth ratio of the pile is in the range of 5.7 to 22.7.

Jan 1, 1996

By Matthew E. Meyer

Renovation, rehabilitation, restoration and expansion of existing residential, retail, commercial, hospital facilities and historic structures requires assessment and evaluation of foundation systems of various ages. The concept of demolition and reconstruction in urban areas is often more challenging, costly, and even prohibitive in some cases due to historic regulations. The authors have been involved with numerous projects related to existing foundation assessment and retrofit, including: hotel and hospital expansions, historic Art-Deco hotel renovations and expansions, garage structure expansions, additions to prominent auction houses, casinos, printing facilities; high-rise structure foundation retrofitting; and forensic evaluations of existing building and highway structure foundation systems, and marine bulkhead sheeting systems. The use of non-destructive testing techniques, high-strain dynamic load testing, full scale pile cap load testing and 3-D laser scanning technology has proved to be vital in the assessment and evaluation process, as well as design of foundation retrofit alternatives. This paper presents various methods and techniques to facilitate a phased approach for re-use of foundation systems. These methods and techniques are illustrated through the author?s experience and selected case histories from projects with varied foundation and geologic conditions.

Jan 1, 2009

By Michael Perlow

Helical screw piles in use since 1838 are routinely used for energy, transportation, municipal, industrial, marine and coastal infrastructure as well as for excavation support, environmental remediation, and foundation repair. They are especially well suited for work in constrained areas, renovations and structure retrofits. Helical pile design procedures over the past 10 years have gone through a remarkable evolution with the establishment of the 2007 AC358 Helical Pile Acceptance Criteria and inclusion of helical screw piles in the 2009 International Building Code (IBC). New 2009 IBC building code requirements and AC358 Acceptance Criteria are presented along with advances in helical pile design procedures, installation, QA/QC, and recommended load test verification criteria. Use of helical smart piles to validate helical pile design and verification of ultimate pile capacity is highlighted.

Jan 1, 2011

By Michael Moran

Typical ACIP Pile Rig [ ] Hollow Stem Auger ? Continuous flight auger ? 3 inch inside diameter pipe ? Auger diameters: 12, 14, 16, 18, 20, 22, 24, 30, and 36 inches ? Auger section lengths: 4, 5, 10, and 20 ft ? Weight ranges from about 70 lbs per ft for 12 inch to 120 lbs per ft for 24 inch and 200 lbs per ft for 36 inch

Jan 1, 2005

By Joel L. Volterra

Since 1910, Mueser Rutledge Consulting Engineers (MRCE) has regularly provided professional engineering services including inspection of pile load tests. Historically, such services included on-site inspection of the driving of test piles and subsequent static load tests by qualified Geotechnical Engineers. Load testing procedures are specified by local or State Building Codes, locally the 1968 Building Code of the City of New York (1968 BCCNY). Between 1968 and 2008, the 1968 BCCNY required a minimum 48-hour hold period for standard loads per pile type, an extended 96-hour hold period for higher capacity piles, and a settlement criterion that the pile maintain a test load equal to two times the design load with less than 0.012 inches of settlement over the last 48 hours of the hold period. Effective July 2008, the new 2008 BCCNY shortened the hold period and relaxed the settlement criteria to that which is more similar to other governing codes and standards such as the International Building Code (IBC 2006) and the American Society for Testing and Materials (ASTM). MRCE implemented an automated load test monitoring system to reduce costs and to alleviate or minimize overnight and off-hour staffing for load test readings. Initially, a series of linear variable differential transformers (LVDTs) and data loggers were included in the Contractor?s load test setup to electronically record pile head settlement and where applicable, settlement of telltales installed to varying depths in the pile. A pressure gage was subsequently added in the hydraulic line, then a load cell, strain gages, and remote access using modems. The ease of the setup and modular adaptive nature of this system have proven it to be a useful tool and improved our ability to better serve our clients and manage our pile load testing services.

Jan 1, 2008

By Herbert F. ?Buck? Darling

A bridge replacement project in Rochester, NY, encountered difficulties when it was determined that rock below one pier was sloping downward toward the river at an angle of 42 degrees versus anticipated 12 degrees. Cofferdam design and construction became very difficult. The unanticipated subsurface conditions delayed the project by eighteen months and increased the cofferdam cost by almost $3.0 million ($US) when direct costs and associated delays were taken into account. The initial approach after discovery of the problem was to use the same type pier design and modify the cofferdam accordingly. This resulted in a cofferdam 12 meters (39.4 feet) deep on the shore side and 18 meters (59.0 feet) deep on the water side. The design used a master pile system to attain required wall strength and used rock anchors to prevent the cofferdam from moving toward the river. The pier foundation was then redesigned by the owner using revised seismic parameters. The original stepped footing carved into rock was replaced by caissons socketed into the rock beneath a large tremie concrete placement. The revised pier and cofferdam designs caused a shift from a mostly land based cofferdam, excavation, and rock removal project into an almost entirely water based cofferdam, caisson drilling, and tremie construction project. These design changes resulted in a reliable, safe, and unusual cofferdam and construction method. All of this was accomplished within a very narrow worksite with a railroad on one side, and the river with its public and commercial freighter traffic on the other. In addition, the existing two-leaf drawbridge was to be maintained in place which put further limitations on the water borne equipment. The engineering and construction considerations, problems, and solutions related to these cofferdams and pier foundations are presented.

Jan 1, 2013

By David Peterson, Terry Tucker, Rafael Serrano

"The Alameda Corridor-East (ACE) Construction Authority awarded a $172.6 million contract to Walsh Construction Company (Walsh) for the construction of a 2.2 mi (3.5 km) long grade separation including a 1.4 mi (2.3 km) long trench that will allow Union Pacific Railroad (UPRR) and Amtrak passenger trains to operate below ground through the city of San Gabriel, Calif. The project is necessary as the ACE trade corridor accommodates approximately 60% of the shipping containers that move from San Pedro Bay, the busiest port facility in the western hemisphere, to the rest of the country via an extensive rail network. Rail traffic is expected to increase by as much as 160% by 2020, and the resultant delays to vehicular traffic is projected to increase by an estimated 300%. The San Gabriel Trench Project is designed to mitigate the effects of this increased train and vehicle traffic throughout the San Gabriel Valley. Malcolm Drilling Company (Malcolm) was selected by Walsh to perform the specialty foundation and ground improvement work for the San Gabriel Trench.This project is part of ACE’s program to create 22 grade separations and safety improvements at 39 grade crossings throughout the San Gabriel Valley. In addition to safety improvements that will eliminate crossing collisions and delays to emergency responders, the project will reduce vehicle congestion and emissions from passenger cars and trucks having to wait for passing trains, and the project will also reduce locomotive horn and crossing bell noise to local residents.Construction of this portion of the project began in late 2012, and it is scheduled to be completed by the end of 2017, having created approximately 9,000 jobs during this period. The project is being funded from Proposition 1B transportation bonds approved by California in 2006, the Metropolitan Transportation Authority (MTA) Measure “R,” and other local and federal funds. The overall project cost is estimated to be $313 million."

Jan 1, 2017

By Chaz Weaver, James Sheahan, Michael Mo

"The Virginia Department of Transportation (VDOT) undertook a program to replace four bridges along approximately 4 mi (6.4 km) of US 340 in Northwest Virginia. Two of these bridges, which span Compton Creek and the Norfolk Southern Railroad respectively, are the subject of this article. HDR provided roadway and structural design as well as geotechnical engineering services for the Norfolk Southern Railroad Bridge while their subconsultant, Saeed Associates, provided structural engineering services in support of the HDR roadway and geotechnical team for the Compton Creek Bridge.The project is located in the Valley and Ridge Geologic Province of Virginia, on an alignment that is adjacent to the Shenandoah River. The project lies within the Beekmantown Group consisting of limestone and dolostone that are prevalent and prone to karstic activity in a band that passes through the project area and north into Central and Eastern Pennsylvania. This area has been impacted by karst limestone conditions where caves and sinkhole activity is common. Caves at Luray and Front Royal, located to the south and north of the project, respectively, are popular public attractions.Since the potential for variability of subsurface conditions can be, and often is, greater in karst terrain, the need to develop a design that provides as much flexibility as possible during construction, and then to be prepared to efficiently review and respond to construction questions is heightened. Coordination and communication among the design staff, VDOT’s design and construction staff, and the contractor was a key factor in completion of this project.Compton Creek BridgeThe alignment for the new Compton Creek Bridge is located about 125 ft (38 m) west of the existing bridge, placing it between that bridge and the existing Norfolk Southern Railroad Bridge. No information about the foundations was available for the existing bridges. Borings in the Compton Creek valley encountered extensive voids (some clay filled and some open) with numerous boulders, rock ledges and pinnacles, particularly on the north side of the creek. Geophysical and geotechnical investigations indicated that below a poor and variable upper zone of rock was a layer of more competent and consistent limestone, which appeared to contain little or no voids."

Jan 1, 2017

By A. J. Partos

Table 4, Page 311 Table 4 Experimental Parameters from Straight Line Interpretation of Mohr Failure Envelope [ ]

Jan 1, 1991

By Dino Kartofilis, Rick Deschamps, Giovanni (John) Bonita

"Anew condominium complex in Arlington, Va., presented some formidable constraints. One was the requirement for a permanent retaining wall to support a 48.5-ft (15-m) cut and an existing 16- story building on top of the slope. Another was the adjacent property owners’ refusal to allow tieback anchors to encroach on their property. The General Contractor (GC) proposed an innovative design incorporating vertical concrete load-bearing elements (LBEs) supported by post-tensioned tiedowns. The owner accepted and the project was successfully completed in 2007.The original designer had proposed a system that included a temporary, raked soldier pile and lagging wall and a permanent cantilever retaining wall with a large piled footing. The system was potentially costly and its constructability questionable.The GC then asked for a design-build alternative to reduce costs and enhance the schedule. The first idea was a diaphragm wall with vertically anchored T-sections. However, configuring a crane to excavate perpendicular sections using grab equipment seemed impossible. There were also utilities approximately 25 ft (9 m) from the existing building, two tiered retaining walls down the slope and a large swimming pool at the base. However, the GC was committed to providing a stable bench 20 ft (6 m) wide along the wall alignment to support the crane.The design evolved to single bite panels using diaphragm wall technology, commonly called LBEs, or barrettes, when they carry vertical loads. For this project, 44 LBEs were horizontally spaced at 9 ft (2.75 m) on center, oriented perpendicular to the wall, extending into bedrock and anchored vertically on the upslope side to resist overturning moments. They were essentially large soldier piles that provided both temporary and permanent support of excavation.An unusual formal agreement was established with the GC to complete the work based on pricing, and prior to completion of final design. This arrangement allowed for an exchange of ideas that increased project efficiencies and lowered costs — without the fear that design concepts would be “shopped” to competitors."

Jan 1, 2009

Abouleid,A.F.327 Ajdic, I.451 Albert, L.F. 221,307 Alem, A. 525 Asama, T. 431 Avgherinos, P. J. 373 Baker Jr, C.N. 331 Balossi Restelli, A. 171 Beckwith,G.H.33 Bellini, A. 469 Bermingham, P. 481 Bertero,M. 171,535 Beyer, M. 503 Bottiau, M.41 Botto, G. 205 Bruskeland, O. 337 Budhu, M. 349 Bullivant, R.A. 181 Bustamante, M.G. 185, 475, 535

Jan 1, 1994

By J. P. Burland

The paper describes a number of recent case histories in the United Kingdom where field instrumentation and measurements have played a major role in the design and construction of excavations, piles and foundations. It is shown that the design and construction procedures for deep excavations in London Clay are based almost entirely on the results of field measurements. Examples are given of successful application of such measurements. The present understanding of the behaviour of bored piles in stiff clays and their design is based on a number of instrumented pile loading tests. The results of these tests have led to a radically new concept of pile design in which the piles operate at their full shaft capacity under working loads thereby resulting in considerable savings in design and construction. Some examples of the successful application of this concept are given. Finally it is shown that the present knowledge of the stiffness properties of chalk is based entirely on field observations. An example is given of how direct field measurements were used to solve a foundation problem at the base of a coffer-dam in chalk.

Jan 1, 2010