Search Documents

By Waddah Akili

This paper describes the steps taken in planning, developing, and executing a case study/ case history course in geotechnical/ foundation engineering at an international university. The paper sheds light on: how a “workable” format for the course was arrived at; the organization of the course; and the results of evaluating the effectiveness of this approach versus traditional lecturing. Problems and challenges that could arise when offering the course for the first time are also addressed. Embedded in this experience and its related protocols are: the emphases on engineering design and the practice, teamwork and leadership development, organizational management, and oral and written communication skills. The paper concludes by confirming that discussions, through an open forum, are judged to be superior to traditional lectures in improving critical thinking, cultivating desirable personal attributes, and acquiring problem-solving skills.

By Gerald Verbeek, Erick Baziw

Stone columns are used in geotechnical site remediation to increase load-bearing capacity and reduce settlement of foundations. Stone columns also improve slope stability and increase the shear strength of a soil. A very challenging problem is to characterize the in-situ shear wave velocities from data acquired from Downhole Seismic Testing (DST) after the insertion of stone columns. DST is an important geotechnical testing tool for site characterization that provides low strain (<10-5) in-situ interval compression and shear wave velocity estimates, but the postanalysis of seismic data acquired from DST in the presence of stone columns is very challenging due to the resulting complicated in-situ soil conditions. To obtain the right results it is necessary to use an algorithm that incorporates source wave raypath refraction. Starting with the Normal Moveout Seismic Cone Tomographic Testing (NMO-SCTT) algorithm developed some years ago, this paper outlines the modifications and additions made to this NMO-SCTT algorithm to facilitate stone column site characterization. To dramatically reduce the optimal solution space for the estimated interval velocities the paper also described a priori conditions that are applied based on the unique nature of the stone column site conditions.

By Ben C. Gerwick

Large diameter steel tubular piles installed vertically or on a slight rake, offer many advantages as the foundations of major overwater bridge in regions of high seismicity. By proper selection of diameter and wall thickness, an optimum balance between stiffness and strength can be achieved. Under strong seismic motion, the piles will deflect and bend so as to reduce the acceleration forces transmitted to the superstructure, while still limiting drift. A major advantage of this concept is that the mass of the footing block is significantly reduced from that of the conventional pier. The design of the footing block requires great care in order to transfer the high shears and moments. Where the soils consist of significant depths of sediments, the kinematic interaction of soils, piles and structures must be considered. Moments will be a maximum just under the footing block. Filling the top portion of the pile with concrete will prevent local buckling and assure ductile behavior even under overload. Typically the piles will be long, with most or all of their support furnished by friction and will require the use of very large pile hammers to achieve the required capacities. Where the piles are founded on rock or in hardpan, sockets will be drilled and filled with reinforced concrete. For these piles, high moments can occur both at the head and just below the rock surface, so the concrete infill should extend the full length. This paper describes the use of tubular piles driven through the deep silty sands of the Jamuna River, Bangladesh, and also where socketed into the near-surface rock for the mail pylon pier of the new San Francisco-Oakland East Bay Bridge in California.

Jan 1, 2013

By Mohamed A. Mansour, Ahmed M. Soliman, M. H. El-Naggar

"Grouted helical piles allow significant increase in pile capacity with low additional cost over that of conventional helical piles. They can be particularly advantageous in sites where installation disturbance can reduce or even eliminate the pile shaft resistance. For helical piles with slender shafts, a grout column offers increased buckling resistance under compression loading, and may reduce the potential settlement required to mobilize the bearing component of their plates. This paper investigates the performance of grouted helical piles installed in loose sand. Grouted helical piles were constructed and tested in a controlled laboratory environment. Helical piles with hollow pipe shaft and single helix were grouted during installation. The grout was injected into the soil under high pressure through two nozzles placed above the piles helices. The load test results showed significant improvement in the performance and load carrying capacity of the helical pile due to the formation of a cylindrical grout column along the entire shaft leading to a higher shaft resistance contribution to the total pile capacity. The results suggest that grouted helical piles with slender hollow shaft could be used to support large structural loads. INTRODUCTIONHelical piles are widely used as a deep foundation system for different engineering applications. They represent an attractive foundation option because of their cost effectiveness, ease of installation even in limited access areas, low levels of noise and vibrations, and their ability to be installed through ground water without casing. In addition, they allow immediate loading upon installation. Helical piles are installed into the ground by applying a mechanical torque to the pile head. The installation torque monitoring provides a kind of quality control during the construction of helical piles. It could be used in predicting the ultimate pile capacity using several capacity-torque correlations (Livneh and Elnaggar 2008; and Hoyt and Clemence 1989).However, helical piles installation can cause soil disturbance within the annular zone affected by the pile helices. This disturbance can introduce fissures within the pile cylindrical failure surface (Vesic 1971; Mooney el al. 1985; and Zhang 1999). Thus, the shear strength of the soil decreases along the affected zone. Bagheri and El Naggar (2013) evaluated the installation effects of helical piles in sand. They reported that as the helical blade proceeds into the ground, sand within the cylindrical path circumscribed by the helices experiences torsional and vertical shearing accompanied by sand displacement and stress changes. This process is more pronounced in the case of multi-helices and large diameter anchors. Bagheri and El Naggar (2016) evaluated the installation effects of helical piles in structured clay. They indicated that the behavior of the helical pile and its capacity are significantly affected by the degree of soil de-structuring induced by the penetration of the pile shaft and helices. In addition to the installation disturbance, helical piles have other drawbacks including; high potential settlement required to fully mobilize the bearing component of their plates, low buckling resistance of their slender shafts, and the incomplete rigidity of the coupling joints along the pile shaft that allow some lateral movement under compression loading (Vickars and Clemence 2000)."

Jan 1, 2016

By Darrell Wilder

The Trenton Water Treatment Facility in Trenton, New Jersey, is expanding to upgrade existing facilities and to meet the increasing demands of the public. The facility sits uncomfortably between the northern bank of the Delaware River and Route 29, a busy traffic corridor. Flooding along this bank of the river occurs frequently and disrupts traffic along Route 29. The expansion plans for the facility call for several large clarifying tanks on a mat foundation covering an area of about 100 x 350 ft. The original design was to remove and replace up to 20 ft of existing fill and soft materials. Due to the close proximity to the existing structures and the Delaware River, it would be necessary to use sheet piles and tiebacks to support the proposed excavation, as well as the existing structures. The solution adopted consisted of the installation of vibro-replacement stone columns to improve the in situ soils and eliminate the need for excavation and replacement. This approach was tremendously successful. It mitigated the significant risk of flooding of the excavation, and provided a cost-effective alternative to mitigate settlement of the proposed tanks on the poor soft subgrade soils. This paper presents the details of the criteria for selection and design of the stone columns, and the process followed for installation of the stone columns and for verification of the level of soil improvement achieved. It also includes a back analysis of the results of a large scale, 10- by 10-foot plate load test performed on a group of stone columns using numerical procedures and recommendations for design and construction.

Jan 1, 2008

By Ramin Motamed, Anna Panorska``, Joseph A. W. Toth

In this study, a dataset of 145 bi-directional and static load tests was used to evaluate the load-displacement response with respect to unit side resistance for drilled shafts comprising fully and partially mobilized data. A total of 612 unit side resistance curves were calculated which included 52 fully mobilized curves showing a maximum response. A new approach using the double tangent method, is proposed in calculating the maximum unit side resistance from partially mobilized load-displacement data. The double tangent method was applied to each load-displacement response to estimate the ratio of mobilized resistance between the intersecting tangents and peak measured resistance. It is observed that as the mobilization of side shear approaches a maximum, the ratio approaches unity. Using the fully mobilized curves, regression models were developed using correlations between ratios of estimated resistance at the double tangent, peak, and maximum measured responses. Regression models are evaluated for the following factors: predominant soil type and drilled shaft construction methods. Comparisons of calculated and measured maximum values of unit side resistance are compared for each model. Although these factors each influence the load-transfer behavior, a single global regression model including all the data showed promise in yielding accurate results.

By Alexandra Weidle, Seffen Leppla, Rolf Katzenbach, Matthias Seip

"A lot of different deep mixing systems have been developed in the last decades for a wide spectrum of applications, e.g. retaining and foundations systems, soil improvement, sealing of toxic substances or dyke strengthening. The paper will deal with special aspects of constructions with deep mixing systems for infrastructures like soil improvement for cyclic loadings and underpinnings in difficult soil conditions by presenting cases from engineering practice.1. DEEP DRY SOIL MIXING FOR SOIL IMPROVEMENT OF RAILWAY TRACKS IN VERY SOFT SOILS1.1 IntroductionRailway tracks are set into vibrations by train passing. In very soft soil this leads to long-term deformations which lead to speed limits, temporary closings and big maintenance efforts. The energy of the dynamic loading is transmitted into the soil by compression and shear waves and at the surface by rayleigh waves (Wood 1968). The expansion of the waves are influenced by•,thickness of the soft soil layer•,density of the soft soil layer•,stiffness of the soft soil layer•,saturation of the soft soil layer•,frequency of the dynamic loadingThe frequency of the dynamic loading depends on the train velocity and the distance of the wheels and wheel sets. If the frequency of the dynamic loading is in the range of the natural frequency of the soft soil layer the vibrations increase extremely (Lieberenz et al. 2003). As a result the long-term deformations will increase as well.To avoid these long-term deformations and the resulting operation restrictions and maintenance efforts an adequate soil improvement is necessary. For the optimization of the soil improvement field tests have been carried out.1.2 Experimental field testsThe field tests have been carried out at a 300 m long test track with five different setups, each 30 m long:•,test track TS 0: no soil improvement•,test track TS 1: soil improvement with single lime-cement-columns 5.9 m deep (Figure 1a)•,test track TS 2: soil improvement with single lime-cement-columns 5.9 m and 10.4 m deep (Figure 1b)"

Jan 1, 2015

By Oladayo O. Komolafe and Majid Ghayoomi

p-y curves have been used over the years to determine the lateral resistance of piles. This method is popular among practicing engineers due to its simplicity and its ability to determine the slope, displacement, shear force, and bending moment for various depths along the pile. The ultimate lateral load resistance is a key component of p-y curve formulation. The p-y curve formulation by Reese et al. (1974) does not consider the effects of soil’s degree of saturation on theoretical ultimate lateral resistance of the failure wedge. This limits an accurate assessment of the lateral soil resistance near the ground surface and the consequent p-y curves. This paper extends the existing approach for determining the failure wedge in unsaturated cohesionless soils with suction dependency, especially for the depths that are above the water table within the wedge. The modification to the failure wedge analysis was made by considering the variation of the degree of saturation which affects effective stress and lateral earth pressure. Through a set of parametric analyses, the impact of incorporating principles of unsaturated soil mechanics in the estimation of theoretical ultimate lateral resistance is examined, and its implications on lateral pile response are discussed.

Sep 8, 2021

By Marcus Daubner, Karsten Beckhaus, Florian Bauer

The construction industry can and needs to contribute to a more sustainable world. Accordingly, geotechnical works potentially have a significant share. In this context, Bauer understands “sustainable products for geotechnical works” as those that may cause less emissions and increase the sustainability of construction activities. In order to structure the efforts and systematically pursue sustainable targets in the construction sector, and in the specialist foundation industry, the “17 sustainability goals” presented by the United Nations in their AGENDA 2030, can be used for general guidance and for continuous improvement. Benchmarks for relevant economic and social objectives, mainly with environmental aspects, are inevitable. The key parameter to sustainable products for geotechnical works in the focus of this paper is the optimisation of processes on site needed to fulfill the client’s building task, including the selection of technologies and construction methods with minimum environmental impact and minimum carbon footprint.

May 1, 2022

By Paul W. Mayne

The axial load-displacement-capacity and load-transfer response of deep foundations can be conveniently assessed by geophysical piezocone tests that provide four independent readings with depth, including tip stress (qt), sleeve friction (fs), porewater pressures (ub), and shear wave velocity (Vs). The penetration data (qt, fs, and ub) of the CPT are utilized to obtain the pile side friction (fp) and end bearing capacity (qb) while the shear wave measurements provide the initial stiffness. Within an elastic continuum framework, the axial pile deflections are calculated and an approximate nonlinear response is obtained by modulus degradation from small-strain response (G0) to intermediate- and large-strains (G). The continuum solution permits separation of load transfer along the sides and proportion to the base. Applications are shown for case studies involving an end-bearing drilled shaft, two friction-type drilled shafts in Alabama and Georgia, and a "Class A" prediction involving driven pipe piles in residuum of the Atlantic Piedmont geology. Load-transfer data were available for the drilled shaft foundations.

Jan 1, 2002

By Nicholas P. Gura

This paper presents the analysis, design, and load test program results for drilled shafts to support a 70-story hotel tower and associated 10 story podium structures located in Las Vegas, Nevada. A mat foundation for the structure, although feasible, would have produced undesirable differential settlements within the high rise tower footprint and at the interface with adjacent lower level podium structures. The resulting foundation system solution for the 70-story, approximately 800-foot long hotel tower was four-foot diameter drilled shafts, extending 100 below shaft cutoff. The design compression capacity for the four foot diameter drilled shaft was 5,000 kips. The load test program proved that the unique Las Vegas valley geology lends itself to efficient installation, precluding the need for engineered slurry or casing. The load testing program included the installation of two four-foot diameter test shafts to 100 feet below theoretical cutoff and the performance of two highly instrumented independent Osterberg load cell tests with maximum sustained test loads of 12,000 kips. Sonic caliper testing was also performed to document actual in-place shaft diameters and verticality. The load test program also provided information necessary for the foundation design of the podium structures. In addition to the tower?s drilled shaft load test program data, continuous flight auger (CFA) pile evaluation and testing was also performed. The CFA testing consisted of traditional ?top down? loading techniques and was performed as an alternative to the recommended shallow drilled shafts for the lower level podium structures. The results of the CFA test program provided supplemental, insightful soil friction data which was used in conjunction with the drilled shaft test program data in evaluating the most appropriate support for the lower level structures.

Jan 1, 2007

By Mustapha Zergoun

This paper presents the results of load tests to assess the vertical load carrying capacity of concrete expanded base piles, or pressure injected footings, for various projects located near Vancouver, British Columbia, Canada. The site subsurface conditions and load test methods are described for the Vancouver International Airport site and the test results are reviewed under both compression and tension loading conditions. The pile load tests at Vancouver International Airport are compared to load tests at other sites near Vancouver. The pile load test results are reviewed with respect to available methods of estimating the vertical capacity of this type of piles. The effect of ground improvement by densification on the load test results is considered. The limitations of tension load tests on single piles with respect to uplift resistance of pile groups under seismic conditions are pointed out. Recommendations are proposed regarding pile load test methodology to estimate ultimate vertical load carrying capacity of plies for limit state design.

Jan 1, 2004

By David C. Kraft

Atlas Systems, Inc. (ASI) resistance type piers were used to underpin a 100 year old historic structure at Fort Monroe, Virginia. This 3-story structure with basement was underpinned with 155 steel tubular push piers (4" OD) that were hydraulically installed to depths ranging between 90 and 110 ft. and to installing forces in excess of 60,000 lb. Project requirements included lowering the basement floor by 1-1/2 ft. and constructing new footings and adding stem walls to connect to the existing masonry walls. Additionally, the underpinning piers were temporary which required the development of a decoupling system to permit the transfer of the building loads from the underpinning piers to the new footings. The structural loads at the foundation level required a c. to c. pier spacing of 3.75 ft. in order to meet project requirements of a minimum Factor of Safety of 3.0 on the pier load capacity. Project requirements included a load test on the selected underpinning pier (ASI - AP2 4000.219) in order to establish installation depths for seating the piers to 60,000 lb. The project was successful in supporting the full load of the structure during the construction phase. Considerable savings in time and cost were achieved as well as avoiding any vibrations or noise during installation of the piers.

Jan 1, 2002

By Dean Abbondanza

"Below grade foundation design has construction issues that above grade foundations do not. These cost factors are dependent on soil conditions and vary by region, but for the most part, the process remains standard.An innovative design concept using steel sheet piles as the permanent wall element changes the traditional cost and schedule for below grade foundations. The sheet pile application reduces dewatering requirements, does not require waterproofing on the vertical walls and eliminates the cast in place concrete wall structure.Foremost, this versatile application affords both Contractor and Designer the choice of two methods of construction; conventional bottom up or top down. The top down method not only provides the savings of bottom up, but also eliminates the cost of anchors while taking the foundation out of the critical path in the early stages of construction. CONVENTIONAL FOUNDATIONSINTRODUCTIONUS construction for a conventional below grade (BG) foundation is fairly standard. Design and install the shoring system, followed by dewatering (if groundwater is present), then excavate in stages with installation of anchorage as work proceeds to final elevation. The site is graded for a waterproofing system to be placed at the base. Once the base slab is cast; forms are set for the vertical reinforced walls. After curing , waterproofing is applied to the back side. The remaining levels are constructed until ground elevation is reached. The site is backfilled and the ground floor is cast. The foundation is now complete and work on the superstructure can now begin."

Jan 1, 2005

By Paul Summers, Kevin Richardson, Willem (Billy) Villet, Paul J. Sabatini, Attasit Korchaiyapruk, Edward C. Clukey

"A deep mixing method (DMM) foundation was selected by the Project Team for a very large LNG facility in West Africa. As described in a companion paper, this foundation consists of a large number of columns installed by mixing cement with in-situ soils. The foundations are arrayed as a variety of honeycombed type configurations which, if installed to desired specifications, can provide a robust foundation alternative. The foundation is capable of distributing loads and limiting settlements even if some of the soil in the columns is not fully mixed during installation. An important part of the overall quality assessment program, therefore, involved developing a testing program to verify the methodology. In addition the impact of potential defects in columns on the overall foundation integrity had to be assessed. This paper describes some of the preliminary work done to establish the requirements for the quality assurance program. A key component of this program involved the sampling frequency used to assess potential defects in the columns. To verify the column integrity 104- mm samples were taken continuously at a selected frequency through the 23 m long columns. The preliminary work described in this paper demonstrated that the appropriate sampling frequency depends on both the desired reliability level as well as the number of defective columns encountered during testing.Initial finite element analyses were performed to assess the extent that defects could occur in columns within the honeycombed structure without adversely affecting the overall foundation integrity. The results from this work demonstrated that the spatial location of the defects was critical to properly assessing the foundation integrity.In addition to column sampling a load test was performed as part of the foundation verification process. The methods used to apply appropriate loads so that loads at the bottom of the columns approached design values are discussed in the paper.The results obtained from this preliminary study were then used to help develop a more comprehensive assessment program, described in a companion paper, to determine the robustness of the DMM foundations for both the LNG processing facilities and a condensate tank.IntroductionFoundations constructed with the Deep Mixing Method (DMM) can be an attractive and cost efficient alternate to other deep foundation options. This foundation is constructed by mixing soil and cement with an auger type drill. The foundation is usually constructed with a dual auger system that simultaneously creates two contiguous columns called foundation elements. Many elements are then arranged in a honeycombed configuration to create the overall foundation (Figure 1). A desired column strength can be obtained by varying the volume of cement added to the columns, the mixing rate of the soil and stroking sequence."

Jan 1, 2017

By Edward C. Clukey

A deep mixing method (DMM) foundation was selected by the Project Team for a very largeLNG facility in West Africa. As described in a companion paper, this foundation consists of alarge number of columns installed by mixing cement with in-situ soils. The foundations arearrayed as a variety of honeycombed type configurations which, if installed to desiredspecifications, can provide a robust foundation alternative. The foundation is capable ofdistributing loads and limiting settlements even if some of the soil in the columns is not fullymixed during installation. An important part of the overall quality assessment program,therefore, involved developing a testing program to verify the methodology. In addition theimpact of potential defects in columns on the overall foundation integrity had to be assessed.This paper describes some of the preliminary work done to establish the requirements for thequality assurance program. A key component of this program involved the samplingfrequency used to assess potential defects in the columns. To verify the column integrity 104-mm samples were taken continuously at a selected frequency through the 23 m longcolumns. The preliminary work described in this paper demonstrated that the appropriatesampling frequency depends on both the desired reliability level as well as the number ofdefective columns encountered during testing. Initial finite element analyses were performed to assess the extent that defects could occur incolumns within the honeycombed structure without adversely affecting the overall foundationintegrity. The results from this work demonstrated that the spatial location of the defects wascritical to properly assessing the foundation integrity. In addition to column sampling a load test was performed as part of the foundationverification process. The methods used to apply appropriate loads so that loads at thebottom of the columns approached design values are discussed in the paper. The results obtained from this preliminary study were then used to help develop a morecomprehensive assessment program, described in a companion paper, to determine therobustness of the DMM foundations for both the LNG processing facilities and a condensatetank.

By H. R. Taber

The extensive subject area "Engineering Practice of Ground Improvement" will be treated within the limitations of space and the writer on the basis of personal practice and experience?largely in Northern California over a period of some thirty-six years and, in "ground improvement" work, with an emphasis on transportation facilities. The stress is on improvement of ground conditions, rather than on techniques of improving inherent earth materials characteristics. "Ground improvement" is discussed as engineering resolution of existing or emergent earth materials defects or deficiencies?that is, as the technically feasible procedures best adapted to achieving a required level of service within physical, economic, social and other constraints. A "required level of service" concept is presented as a tool in evaluation of appropriate ground improvement work.

Jan 1, 2010

By Hector Simchas

"1. BENTONITE: THE CRUCIAL CONSTITUENT OF SLURRYSuspensions of bentonite and water are used in a variety of applications in underground engineering. For the construction of underground elements like slurry walls or piles, bentonite slurries offer support to the excavation of loose soils and counter pressure against hydrostatic pressure of ground water, especially where soil permeability is high. In addition, for the construction of tunnels by the slurry-shield method or when hydromills are used for excavation, bentonite suspensions transfer the loosened soil to the surface. In applications like pipe jacking and microtunneling, or where high revolution drilling is required, bentonite also provides lubrication and cooling.To fulfill these functions, the properties of a bentonite slurry need to remain stable, or at least predictable, during the course of construction. Unfortunately, when a suspension mixes with earth, ground water and/or impurities, its properties may be compromised resulting to reduced performance, which would in turn lead to increased construction costs and the risk of the excavation collapsing. Our experience in the lab and onsite is presented herewith.2. MOST USUAL FACTORS OF PERFORMANCE FAILUREWater and soil quality are important factors defining the behavior of suspensions. In an extensive program of measurements in our technical laboratory, the effect of frequently encountered harmful substances on bentonite suspensions has been examined and the results are summarised in Table 1.Some tests show that the conductivity of water has a direct relationship with Marsh Viscosity. For example, we have seen that if the quantity of bentonite required to achieve a 40s Marsh Time ranges between 50-52 kg/m3 at water conductivity below 100 µS/cm; when conductivity is increased to 1,400 µS/cm, we need 65-68 kg/m3 in order to achieve the same property."

Jan 1, 2015

By Bill Paparis

The thirty year old wharf structures at the Port Authority of New York & New Jersey?s Port Elizabeth Marine Terminal are being modernized for the next generation of Post-Panamax container ships, which require deeper water and larger container cranes. The terminal operator is upgrading the wharf in order to remain competitive, now and into the future. The upgrade coincides with the Army Corps of Engineers? $733 million project to deepen the main shipping channel in New York Harbor. This paper focuses on the structural modifications to accommodate berth deepening and to support the heavier loads of the new cranes. An overview is provided of the design and actual construction, including typical problems encountered when combining new and existing structures. The wharf improvements included: ? Installation of a steel king pile/sheet pile cutoff wall along the face of the wharf to permit increasing the depth from ?12.2 m + 0.61 m to ?15.2 m + 0.61 m ( ?40 ft + 2 ft to ?50 ft + 2 ft) ? Removal of the existing crane rail support beams and installation of new piles and beams to support the increased crane loads ? Replacement of the existing timber fender system with a new system capable of resisting the berthing energy of a 152,000 MT displacement vessel, and having dedicated sections for berthing barges ? Replacing the existing overhead, landside crane electric feeder system with a waterside, cable reel trench system. The work included upgrading the transformer capacity at the terminal for increased crane power demands This paper provides a case history for port administrators, terminal operators, engineers, and shipping lines challenged with upgrading aging terminals.

Jan 1, 2013

By W. Morgan NeSmith

A drilled displacement pile program was utilized for the expansion of an existing power plant in Cohasset MN adjacent to the Mississippi River. The drilled displacement (DD) pile is an innovative foundation type that provides exceptional value in some geologies. In the U.S., DD piles have typically been used in coarse-grained soils due to the large friction capacities that can be generated by the piles in these conditions. This project was the first large scale experience for the project team where it was anticipated that significant portions of the DD pile capacity would be developed in primarily fine-grained soils. The project site consisted primarily of variable amounts of fill overlying predominantly low plasticity alluvial silts. In some cases, alluvial silty sand layers were encountered within the expected pile installation depths. Alluvial sands were typically encountered below the silts, in some cases within the expected pile installation depths. The project team developed a probe and pile load test program to address the variable subsurface conditions across the site. The program included monitoring various parameters (including applied torque and tool penetration rate) during the drilling portion of the pile installation using recently developed data acquisition techniques. This data was used to estimate the rig energy, or Installation Effort (IE), required for pile installation. IE profiles from the test and indicator piles were compared with subsurface data available from a number of previous site characterizations. Additionally, Cumulative IE values were compared to an in-house database of IE vs. DD Pile Capacity. Final production pile toe levels were based primarily on IE values selected from this comparison. The IE data collected during production was also used to address large variations in pile-cutoff elevation (relative to a fairly uniform ground surface elevation).

Jan 1, 2008