Search Documents

By Stefan Dahlin

The laboratory tests indicated low permeability but as I said, as a rule, the permeability in the field has been found to be higher. A high permeability has also been found when doing back calculations of rates of settlements in different cases. But as I also said, there's a need for further studies in this area.

Feb 10, 2003

By R. Lee Wooten, David R. Shields, Darren D. Clark

"Borehole permeability tests that measure flow or head changes in boreholes located within seepage barrier walls are commonly used to estimate the in situ permeabilities of those walls for quality control and assurance. The current state of practice for estimating permeabilities from these barrier wall borehole tests is to use equations published by M. J. Hvorslev in 1951. Hvorslev’s borehole test equations model an infinite stratum of uniform permeability, which is not the actual condition for a test performed in a low permeability barrier wall located within a high permeability stratum. We examine and develop alternative equations based on line source analytical models, which more closely match barrier wall test conditions. We describe how these alternate equations can be used to estimate barrier wall permeabilities from borehole tests and compare the results to those obtained from the Hvorslev models. We also provide recommendations that consider differing upstream and downstream water levels.Barrier Wall Permeability Tests - State Of PracticeThe installation of seepage barrier walls has become more common in a variety of applications ranging from dams and levees to contaminated sites requiring retardation of groundwater flow. The types of seepage barrier walls and installation methods include soil-bentonite, soil-cement-bentonite, concrete, self-hardening slurry, geomembranes, and sheet piles, installed with various soil mixing, slurry-supported trench, and driving methods.Owners and contractors have used a variety of methods to evaluate the permeability of these seepage barriers. The following table lists commonly used quality control/assurance tests for evaluating the permeability of a seepage barrier."

Jan 1, 2016

By Yazen Khasawneh, Osvaldo P. M. Vitali, John E. Agee, Mohammad Nassim

A 3D FEM modeling of a ground improvement solution for an ice rink slab with stringent differential settlement limits is presented. Due to the complexity of the geotechnical conditions and strict deformation requirements, a structural slab supported by micropiles was initially proposed. However, this solution was costly and alternative solutions using ground improvement techniques were investigated. The proposed slab is supported directly on rock at one end and on approximately 45-ft deep cohesive soils on the other end. The numerical simulations show that differential settlement would be larger than allowable, if the ice rink slab is supported directly on the existing subgrade. The addition of the ground improvement scheme with compaction grouting demonstrated that the anticipated differential settlements are reduced significantly and would become less than the allowable magnitude. This study demonstrates that the use of numerical simulations to study complex loading and geological conditions will help to optimize designs and may result on significant cost savings.

Sep 8, 2021

By Allen Cadden

The type of soil we had was a silty fine sand. It had been placed by hydraulic methods in 1904 so it was quite clean I would say less than 10% silt the rest of it was very loose sand. That I'm not certain, I've only done it on sandy soils but it would stand to reason that some sort of a number should apply because you are measuring the amount of work that you are doing to it so if the soil is fairly consistent over the site it should be able to generalize from there but I don't know for a fact that it works. Well, verifying to ourselves that this method actually worked because we weren't certain at first when we were doing it so then we would develop the numbers and then check the results.

Feb 10, 2003

By Sunil Arora, Lisheng Shao, Chris Conkle

"The East Garden Grove - Wintersburg Channel located in Orange County, California, required upgrades along the levees to mitigate potential liquefaction and lateral spreading hazards. The Orange County Public Works designed soilcrete columns constructed between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue (approximately 2,500 ft), and along an approximately 2,000-ft-long stretch of the south levee. The earthen embankment, approximately 13- to 15-ft high and damaged significantly by erosion, was then excavated to widen the channel to increase the channel flood conveyance capacity.The site is located within the Los Angeles Basin, underlain by several thousand ft of marine sedimentary strata. Uncontrolled fill materials were encountered to approximately 10 ft below ground surface, underlain by tidal and flood plain deposits. Groundwater was encountered at sea level, which is approximately 10 ft below grade.This paper will discuss site soil conditions, and the construction and quality control of soilcrete columns constructed by wet soil mixing; also, the paper will introduce the Drilling Index (DI) as a measurement tool, similar to the cone penetration test (CPT), to evaluate the soil strength in more detail. Finally, the statistical analysis of soil mixing strength distributions for the project quality control will be presented.INTRODUCTIONWintersburg Channel in Orange County, California, required ground improvements along the existing levees to mitigate potential liquefaction and lateral spreading under the site design earthquake. Orange County Public Works designed and developed a cellular pattern of soilcrete columns sandwiched between two rows of steel sheet piles along both sides of the channel between Graham Street and Warner Avenue, and adjacent an approximately 2,000-ft-long stretch of the south levee (Fig. 1). An earthen embankment approximately 13 to 15 ft high, damaged significantly by erosion, was then excavated to widen the channel and increase the channel flood conveyance capacity.Stiff, soilcrete cellular wall structures can reduce the earthquake-induced cyclic shear stress ratio (CSR) in the soil within the cells, thus preventing excess pore water pressure build up which may trigger soil liquefaction. For this project, approximately 6,700 soilcrete columns were constructed in a cellular pattern to an approximate depth of 40 ft. All of the soilcrete columns are 3 ft in diameter with the design unconfined compressive strength (UCS) of 150 psi."

Jan 1, 2015

By Melinda J. Hummel, Zachary T. Smith, Nathaniel Witter, Nina F. Carney

The revitalization of Pittsburgh’s historic Strip District has led to the redevelopment of existing properties and the development of new properties. At one time, the Strip was home to wholesale market products. Now, the historical warehouse buildings are being converted to multi-use residential and commercial properties. One such property, 1600 Smallman Street, consisted of 1 to 6-story connected buildings that housed night clubs, retail shops, and office space. The lower story portion of the building, on the southwest side of the property, was torn down to make room for a new 5-story- parking garage with street level retail space. The remaining 6-story-building, on the northeast, was gutted to be renovated into high-end condominiums, keeping the exterior historical building facade.

By Rahul Wankhade, Sunil S. Baswankar, Aditya S. Kharatkar

Despite advances in pile design methodologies and piling techniques at site, difficulties and uncertainties still exists for design of piles particularly in coralline deposits and weak carbonate rocks. Such deposits are known to be heterogenous in nature, and occupy major stretches of earth, where piling experiences are probably very scanty. Such deposits are associated with low unit weights and usually consist of weakly cemented calcareous and carbonate soils interbedded with coral rocks containing cavities, which are completely void or filled with coral debris. Many of the studies indicate that conventional parametric relationships are may not apply to such sediments and rock formations. This paper intends to provide an appraisal of the available information that cautions against risks involved in conventional design practice and also serve as a guideline for pile design in such formations despite being a grey area of research. Contents of the paper is expected to provide a basis for the pile design and likely to serve as an eye-opener for research into this important soil-pile structure interaction problem.

Sep 1, 2022

By Brian W. Wilson

A case study is presented that describes the design and implementation of a combined blast densification and deep dynamic compaction program which was undertaken to improve the foundation soils for a proposed tailings dam raise in Ontario, Canada. Based on the results of the geotechnical investigation it was determined that the foundation of the dam would be situated on tailings of both variable thickness and density, much of which would be susceptible to liquefaction under the design earthquake for the region and type of facility. Blast densification trials were completed by the owner and the results of these made available to prospective tenderers in response to a call for a fixed price contract for the design and implementation of a densification program for approximately 800,000 m3 of foundation tailings. The variation in tailings gradation and the impacts of such on the ground improvement program are discussed, as are details of both the additional blast densification field trials completed by the contractor, and the selected blast pattern and explosive charging used for production blasting. The applicability of the various ground improvement techniques to the actual conditions encountered, and the results obtained are also discussed.

Jan 1, 2010

By Michael Forrest, John Roadifer, Glen Gorski

"The Calaveras Dam Replacement Project (CDRP) requires large disposal sites to store excess excavated materials that could not be utilized for dam construction. Because of access restrictions during design, the disposal site rockfill toe dike area at the edge of the reservoir could not be explored to evaluate soil conditions. As such, the site had to be explored as part of the construction contract. Exploration revealed very soft clay and loose silty sand up to 40 feet thick that would not be able to support the rockfill dike at the toe of a large disposal site fill. Several alternatives were evaluated to stabilize these soils. Based on constructability, cost and risk considerations, cement deep soil mixing (CDSM) was selected as the preferred method of soil stabilization. The challenge was to design and construct the CDSM stabilization to minimize construction delays. A joint effort by the design engineer, construction manager and contractor achieved CDSM stabilization in about three months, from design through completion of construction. A rigorous quality control program included compression testing of both wet grab and cored soil cement samples to demonstrate that specified strength requirements were being achieved.INTRODUCTIONDisposal Site 3 (Figure 1) is one of the primary CDRP disposal sites having a height of 240 feet and a storage capacity of about 2,500,000 cubic yards. An approximately 40-foot-high rockfill dike at the base of the disposal site provides an erosion resistant toe for the disposal site. The rectangular foundation area shown in red was not able to be investigated during design because of access restrictions."

Jan 1, 2015

By Mario Mauro

In 2007 the US Army Corps of Engineers classified the Herbert Hoover Dike in Florida as a Dam Safety Action Classification (DSAC) 1 dam, and started the implementation of one of the largest dam rehabilitation projects in the nation. The construction of the cutoff wall is a key feature of this rehabilitation work to upgrade the dike to current dam safety criteria. The cutoff wall installation is currently being completed on Reach 1, which extends from Port Mayaca to Belle Glade, under a Multiple Task Order Contract based on performance specifications and stringent verification criteria. For the construction of the cutoff wall TREVIICOS selected the self-hardening slurry method. Since the cutoff wall is installed through a layer of highly variable limestone with Unconfined Compressive Strength (UCS) up to 14,000 psi, the excavation requires the use of the hydromill equipment. This is the first successful application of the hydromill technology with self-hardening slurry in a large scale project in the US. This paper presents the details of the method utilized, the quality control procedures, and the experience gained over seven miles of cutoff wall installed.

By Ronaldo Luna, Donald Deardorff

"The use of load and resistance factor design (LRFD) is well documented since the 1960s for structural applications when it was first adopted into the American Concrete Institute Building Code in 1963 and was established for geotechnical applications by the Danish Geotechnical Institute about the same time under the name of Limit State Design (LSD).The Federal Highway Administration required all federally funded projects to use the LRFD method by 2007. Due to this funding requirement, recent LRFD research for geotechnical applications has focused on common bridge foundations (i.e., driven or drilled shafts), resulting in good documentation for design using these methods. Unfortunately, the practicing geotechnical engineer does not intuitively know how to create resistance factors for deep foundations systems that have design methodologies and installation techniques significantly different from driven or drilled shaft foundation systems.Helical anchors typically use semiempirical methods for preliminary capacity design and a torque correlation methodology during installation to verify required capacity. Here we provide basic information on the LRFD methodology for helical anchor design. Additionally, the First- Order Second Moment (FOSM) method is applied to a previous helical anchor study (Hoyt and Clemence 1989) to determine resistance factors for an ultimate tension capacity strength limit state.MethodologyThe concept of the LRFD method is to establish factors for both the load and resistance that account for uncertainties using probability theory. The factors increase the nominal load and/or decrease the nominal resistance such that the probability of failure is an acceptable value. LRFD also accounts for the effects of load combinations (dead, live, seismic, wind, etc.) by determining the probability of the combined occurrence. The general form of the LRFD equation used by American Association of State Highway and Transportation Officials (AASHTO) is:"

Jan 1, 2009

By Filippo Maria Leoni, George Filz, Wesley Schmutzler, Matteo Bertoni

"The US Army Corps of Engineers selected the Deep Mixing Method (DMM) for the required stabilization at the LPV 111 Project (New Orleans, USA). DMM was used for ground improvement/foundation strengthening and consequently to stabilize and support the burden of the new levee. Two different technologies were used: Trevi Turbo Mix (TTM) and Contrivance Innovation Cement Mixing Columns (CI-CMC). LPV 111 is the largest soil mixing project to date in the USA with its more than 18,000 elements installed to a depth of up to 67 feet for a total of 1.7 million cubic yards of treated soil. The preparation and execution of the project presented many challenges from various points of view. The little time available to complete the job led to the simultaneous utilization of eight deep mixing rigs and batch plants which worked 24 hours per day, 5.5 days per week on a stretch of land approximately 5.3 miles long. Given the imposing geographical extent of the project, a four phase laboratory programme and five field validation test programmes, conducted in as many different areas of the project, were completed to design and optimize the grout mixes and the installation parameters. The massive quality control/quality assurance testing programme produced over 500 drilled core holes and over 5,000 tested specimens in order to determine unconfined compressive strength (UCS) and uniformity of the DMM elements. This paper has the purposes of describing the tremendous challenges encountered and providing valuableinformation that may be useful for other future projects, including details not previously published.INTRODUCTIONReach LPV-111 is part of the Lake Pontchartrain and Vicinity Hurricane Protection System designed to protect the city of New Orleans and the surrounding areas from the surge that would accompany a 100 year hurricane event. LPV-111 measures approximately 8.5 km (5.3 miles) long, of which 7.2 (4.5 miles) extend along the north bank of the Gulf Intracoastal Waterway (GIWW) and the remaining 1.3 (0.8 miles) run north and terminates at the CSX Railroad Gate. The Bayou Sauvage National Wildlife Refuge borders the levee on both sides (Fig. 1)."

Jan 1, 2015

By Kirk Ellison, Sherif Elfass, Ramin Motamed, Kevin V. Stanton

"The determination of accurate load transfer curves are essential for estimating deep foundation loadsettlement response using t-z style analyses. While recently developed semi-empirical methods from Ashour et al. (2010) and Ashour & Helal (2012) have shown promise in preliminary studies, they have not yet been thoroughly benchmarked against a more widely accepted approach. To address this issue, these recent procedures are implemented in the computer program CGI-DFSAP to predict the results of four Osterberg-cell (O-Cell) load tests. These predictions are compared to outcomes obtained following the recommendations from Reese & O’Neill (1988) for t-z analyses of drilled shafts in sand and clay which are carried out with the program TZ-PILE. Overall, the results suggest that the new approach offers improved accuracy regarding predictions of drilled shaft response to axial loading.INTRODUCTIONThe behavior of axially loaded deep foundations is often analyzed using a technique known as the t-z method. In this method, deep foundation elements are broken into multiple segments which are supported by discrete nonlinear springs to capture the contribution of both side-friction (t-z springs) and end-bearing (Q-z springs). Hence, the t-z and Q-z relationships dictate the predicted load-settlement response. A number of different approaches have been developed to estimate load-transfer curves with some relying solely on empirical data from laboratory and field experiments (i.e. Coyle & Reese, 1966; Vijayvergiya, 1977) and others based mainly on analytical frameworks (i.e. Kraft et al., 1981; Randolph, 1994). Reese & O’Neill (1988) provide recommendations which are widely used for developing t-z and Q-z curves for analyzing drilled shafts. This method is hereafter referred to as Method 1 (M1). It should be noted that these empirically derived relationships are only applicable for problems associated with drilled shafts and are therefore not appropriate for developing load-transfer curves for other types of deep foundations (i.e. driven piles). This is because of the difference in the frictional resistance which can be developed between a circular concrete-soil interface as opposed to that of other materials (i.e. steel) and/or different cross sectional geometries.The M1 load-transfer curves form the basis for the t-z analysis of drilled shafts implemented in the computer program TZ-PILE (Ensoft, 2014). In light of this, TZ-PILE is employed herein as a reference to compare against the capabilities of another method of implementing t-z style analyses. This method is based on a semi-empirical framework for soil behavior developed by Norris (1986) and is implemented using the program CGI-DFSAP (Computers & GeoEngineering Inc., 2011). More information concerning this approach, hereafter referred to as Method 2 (M2), is given in subsequent sections."

Jan 1, 2017

By Akshay Sakhuja, M. S. Karthika, R. Vignesh

"The bridge across River Mandovi in Goa is a cable stay bridge structure proposed parallel, along existing bridges for regulation and reduction of vehicular traffic; the entire bridge structure is supported on pile foundation socketed in rock. This paper describes drilling related issue encountered during execution of pile where bed rock varies considerably from factual geotechnical investigation, which in turn affected the productivity of bored piles socketed in rock then chiseling is advocated for rock socketing with limited number of blows based on penetration resistance of rock encountered or equivalent energy principle to increase the productivity and also to avoid excess chiseling which otherwise would have fractured the rock mass below and around the pile tip resulting in increased settlement of pile subjected to design load. Contractor decision on socket length have been taken without compromising either quality or productivity; the paper presents various procedures and the equipment involved for installation of pile in rock along with the conclusion related to termination of pile in rock and also the lessons learned in process.INTRODUCTIONPile foundations are generally used to transfer heavy loads in deeper bearing stratum if the soil immediately beneath the base of the foundation does not have sufficient capacity. The bridge across River Mandovi, Goa is in its construction phase as a part of the development plan of Goa State Infrastructure Development Corporation Ltd (GSIDC). The project was awarded to M/s. L&T Construction, Heavy Civil Infrastructure; subsequently the geotechnical investigation was awarded to M/s L&T Geostructures.The client has specified the foundation of the bridge as rock-socketed. Rock socketing is generally done to achieve higher bearing pressure through concrete-rock shear interface which many building codes permit. The design and construction of rock socketed pile foundation entails a detailed analysis and judgement on the superstructure loads, predominant geological conditions as well as ground water levels. The termination of pile is normally based on thumb rule of half to three times the pile diameter into the rock. Quite often the criteria is based on chisel penetration rate (Gandhi,1990) In fact, this is the key factor to consider appropriate and economical depth of embedment of pile into rock stratum which necessitates enormous understanding on the type and quality of rock strata encountered which may significantly influence the selection of suitable rotary rig for pile installation. Such criteria are site specific and also applicable for the set of equipment used for the particular project."

Jan 1, 2015

By Lois G. Schwarz

I did not make studies about this parameter but I can say that some researchers recommend using low C3A cements to repair masonry mortar in order to reduce a possible combination with sulphate that can be present in old mortars.

Feb 10, 2003

By K. Madhusudan Reddy

"Pile response under combined uplift and lateral load is very important and it is imperative to evaluate the effect of combined loading and only few studies were reported on pile behavior under combined uplift and lateral loads. Model pile made-up of aluminum having an outer and inner diameter of 25.4 mm and 19.4 mm respectively is used. Dimensions of the model steel tank are fixed as 1.0 m x1.0 m x 1.2 m (depth) to avoid the boundary effects under combined lateral and uplift loads. Experiments were carried out on single piles at isolated uplift, isolated lateral loading and combined lateral and uplift loading, embedded in sandy soil. Results indicate that load–deflection behavior is nonlinear for isolated uplift and lateral load tests as well as in case of combined loadings. It is also observed that the behavior of piles under isolated loadings is substantially different when compared to combined loading.INTRODUCTIONPile foundations are generally used to support compressive loads from superstructures. Some structures, like transmission towers, mooring systems for ocean surface or submerged platforms, tall chimneys, jetty structures, etc. are constructed on pile foundations, which have to resist large lateral and uplift loads and moments. The various loads (compressive, lateral and uplift) and moments act on the piles simultaneously rather than isolated manner. There are well-established theoretical methods present to evaluate the pile behaviour under different isolated loadings namely, verticalcompressive, vertical-uplift and lateral (Poulos and Davis, 1980), but there are very limited studies focused on pile behaviour under combined loadings. Though there is good number of studies reported on pile behaviour under combined compressive-lateral and compressive-uplift loadings (Ramasamy, 1974; Jain et al. 1987; Zhang and Small, 1999; Dash and Pise, 2003; Karthigeyan et al. 2006 & 2007; , there are only very few studies reported on pile behaviour under combined uplift and lateral loads. Darr et al. (1990) described an approach to a rational solution of the interaction of pile to combined uplift and lateral loads based on analytical and experimental studies. Influence of cyclic loading was also considered. Narasimha Rao and Prasad (1993) investigated the uplift behaviour of pile anchors subjected to lateral cyclic loading. There were many onshore and offshore situations where lateral cyclic loading may affect both the pullout and lateral loading capacity of pile anchors. Jetty and wharf structures are usually subjected to lateral forces from wave and wind action. If these cyclic lateral loads are acting on the supporting piles, the resulting movement of the upper part of the embedded length of pile may reduce the skin friction. This progressive deterioration in pullout resistance may not be reflected by a pullout test made soon after the installation. Hence, Tomlinson and Woodward (2008) pointed out that a generous safety factor on the ultimate pullout load should be adopted for piles in such situations. Mroueh and Shahrour (2007, 2008) presented a threedimensional finite element analysis of the response of battered piles to the combined lateral and vertical pullout loads. Nevertheless, the model is not validated well due to lack of good experimental data based on rigorous experiments. Thus there is a scope for investigating the effect of lateral load on pile behaviour under uplift load and vice versa based on carefully designed experiments, which is main focus of the present investigation."

Jan 1, 2017

By Tom George

"INTRODUCTIONNo. 1 Queens Rd was an existing 10-storey office building founded on large pad footings. This project involved the construction of a 6-level, 15m (50-ft.) deep basement excavated immediately adjacent to the existing building and also beneath the existing footprint of the Southern end of the building. The total perimeter of the new basement was to be approximately 200m (656 ft.) all with a retained height of 15m (50 ft.). It was also proposed to add a further 5 storeys to the building. Approximately 18 of the existing columns supporting the 10-storey building were to have the applied column load diverted from the existing foundations at ground level onto the new piles or basement raft 15m (50 ft.) below.The geotechnical profile consisted of fill for the top 1.5m predominately comprising of clayey sand with a high gravel content from 1.5m to 9m (5 to 30 ft.), a medium dense to dense clayey sand and then below was a sandy clay extending to 15m (50 ft.) ranging from stiff to very stiff. From 15m on completely to extremely weathered siltstone was encountered. The groundwater was measured at 9.5m (31 ft.) below the natural ground surface.DESIGN BRIEFThe existing building columns were founded on large pad foundations up to 4.4m (14.5 ft.) square, founded on the dense clayey sand. These pads would require temporary support to enable the excavation to proceed beneath them. Upon completion of the excavation under the pads new columns were to be constructed joining into the existing columns to transfer the load onto the new raft slab, 15m (50 ft.) below. The existing 10 floors were to be refurbished. It was planned to undertake all the temporary support and transferring of loads while the structure above was only able to provide a dead load. It was decided that any movement of the building would have minimum impact on a skeleton structure. During the temporary support of the columns, movements due to construction activities had to be monitored to understand any potential stresses in the structure above.The original design required beams to be installed under the pads and supported at either end by temporary piles that were to be founded below the level of the proposed excavation. (Refer to sketch 1). Wagstaff Piling considered that this methodology had difficulties in construction at all stages and did not provide facility for transfer of the load without significant movement of the structure above. Wagstaff Piling revised the design to attach beams to the columns above the pads using shear collars. (Refer to sketch 2). These beams supported on the temporary piles could then be jacked upwards to remove loads off the pads. This would enable removal of the pads with minimal movement of the 10-storey building above. (Refer to photo 1 and back cover photo)."

Jan 1, 2005

By Giovanni A. Bonita, Asher H. Peltz, Sean D. Johnson

This paper examines a complex earthwork project in the Washington DC metro area that had project delivery directly impacted by questionable instrumentation monitoring data. The case study summarizes the impacts to the project caused by questionable instrumentation data and reveals how the authors were able to utilize data to extract meaningful insights. The case study also demonstrates how clear data presentation became a key factor in maintaining stakeholder trust and facilitated progress of the project schedule. The case study highlights key points to collecting high quality instrumentation data, approaches to assess and improve value of the data collected, and techniques to reduce and interpret questionable data.

By Patrick J. Hannigan, Frank Rausche, Rozbeh B. Moghaddam

The Top-Loaded Bi-Directional Test (“TLBT”) is a new method to apply bi-directional loads to a deep foundation element with the loading source located above the foundation head. In the TLBT reusable load assembly, loads are applied to the foundation using the R-System which consists of two stacked steel plates located at the geotechnical resistance balance point or at the foundation base connected to the load assembly via vertical elements. The top plate or the Shaft Bearing Plate (“SBP”) will transfer loads to the foundation upper portion, and the bottom plate or the Base Bearing Plate (“BBP”) will transfer loads to the foundation lower portion as well as the foundation base. At the surface, above the foundation head, a hydraulic jack is located between a Top Load Assembly (“TLA”), and the Bottom Load Assembly (“BLA”). The TLA and BLA are connected to vertical elements which are consequently connected to the R-system. As the jack is pressurized and expanded at the surface, the R-System plates are separated, and the foundation is bidirectionally loaded. This paper presents a brief description of the conventional Bi-Directional Load Test (“BDLT”) including benefits and limitations followed by the TLBT method introduction including its benefits and advantages over other testing methods.

Sep 8, 2021

By Seth Robertson, Daniel Belardo, Travis Coleman

Thermal Integrity Profiling (TIP) is a non-destructive method used to evaluate drilled deep foundation integrity. This integrity testing method is specified more frequently, and is becoming an industry standard in the transportation and private construction sectors. This testing method utilizes heat generated during the concrete/grout curing process to assess deep foundation integrity over the evaluated length. With compilation of the measured temperature versus time and installation records, a model of the Effective Average Radius versus measurement depth is generated. The generated effective shaft model is highly dependent on specific construction details, subjective modeling parameters, and proper interpretation of concrete/soil heat dissipation characteristics. Key components of the TIP analysis include both qualitative and quantitative assessments. Qualitatively, variations or sharp reductions in temperature profiles may indicate potential anomalous regions. Quantitatively, a correlation is established between measured temperatures and estimated Effective Radii for subsequent integrity evaluation. Best practices in processing the TIP measurements are presented, including selecting the optimal time for analysis, normalizing the thermal profile, and proper interpretation of potential anomalous regions. Recommendations for implementing mitigation efforts and interpretation of the TIP results are presented.

Sep 8, 2021