Search Documents

By R. Dahlke, J. A. Finch

A campaign was undertaken during the greater part of 2001 at Noranda’s Brunswick mine concentrator to investigate the role of gas (air) superficial rate (Jg) distribution to the cells in the final Zn cleaning stage (bank of seven cells), i.e. the Jg profile. Three profiles were tested: “balanced” (each cell with same Jg), “increasing” (from cell 1 to 7 proportionally), and “decreasing,” along with an “as found” profile in a parallel control bank. The experimental design allowed for two confounding factors, changes in ore type and circulating load. The increasing profile consistently gave the best metallurgy (down-the-bank grade / recovery). The reason for improved performance was the response of the first cells in the bank where the increasing profile gave the highest selectivity of sphalerite against nonsulphide gangue (NSG). The other profiles gave lower selectivity and higher zinc recovery in the first cells, which combined to reduce overall bank performance. The higher selectivity with the Increasing profile is attributed to the low gas rate in the first cells reducing water recovery and hence limiting entrainment of NSG. The increasing profile was subsequently configured for all four stages in the zinc cleaner circuit.

Jan 1, 2004

By M. King Hubbert

"The present large-scale use of energy and power by the human species represents a unique event in the billions of years of geologic history. Furthermore, in magnitude, most of the development has occurred during the present century. In the United States, the peak in the rate of petroleum production occurred in 1970 and that for natural gas is imminent. The peak in the world production of crude oil is expected to occur at about the year 2000 and that for coal production at about 2150 or 2200. For other sources of energy and power, water power, geothermal power and tidal power are inadequate to replace power from fossil fuels. Nuclear power, based on the breeder reactor and utilizing lowgrade deposits of uranium and thorium, has a larger potential than the fossil fuels, but it also constitutes a large perpetual hazard. The largest source of energy available to the earth is solar radiation. This source has a life-expectancy of a geologic time scale, is nonpolluting and is larger in magnitude than any likely requirements by the human s pecies. In consequence of the large supplies of available energy, the period since 1800 has been one of an unprecedented exponential industrial growth. This also has been accompanied by a world-wide ecological disturbance, including that of the human population. It can easily be seen that such a period of growth must be ephemeral in character and, in fact, is now almost over. One aspect of this transition from a state of exponential growth to a state of nongrowth is the present alarm over an ""energy crisis."" Actually, the world's present problems are by no means unmanageable in terms of present biological and technological knowledge. The real crisis confronting us is, therefore, not an energy crisis but a cultural crisis. During the last two centuries, we have evalved what amounts to an exponential- growth culture, with institutions based on the premise of an indefinite continuation of exponential growth. One of the principal consequences of the cessation of exponential growth will be an inevitable revision of some of the tenets of that culture."

Jan 1, 1973

By Tom Shumka

"All mineral processing facilities that use girth gear driven mills need to inspect the gear teeth on a routine basis, whether it be every six months to every three years. The inspection frequency depends on gear tooth condition, and the objective is to ensure the operational integrity of the gear teeth. Conventional methods such as magnetic particle testing, visual inspection or dye penetrant examinations rely heavily on operator interpretation. At best, these techniques can determine whether a defect exists, but are unable to provide information on defect severity. This paper describes the use of combining combined eddy current array (eca) and alternating current field measurement (acfm) to provide a complete survey of all surface breaking indications on the whole gear tooth depth. This method accurately determines the size, length and depth of any cracks found on the surface.INTRODUCTION In order to gain a fundamental understanding of the evolving operational and production behavior of a piece of machinery over a specified time period as part of an effective condition monitoring program, a robust data collection process must be firmly established and adhered to. To be effectively implemented within an organization, a condition monitoring program must have support of not only the maintenance, production and engineering staffs, but also executive management support to ensure successful roll out to realize the maximum productivity of the machinery and subsequent cost-savings. One of the key elements of a mineral processing facility that use gear driven SAG Mills as a primary stage for grinding solution, is the integrity of the critical gear unit that drive the mill. For the maintenance team, condition monitoring on the gear unit is crucial for preventative maintenance. A catastrophic failure in the critical gear unit would require a minimum of ten days to replace the gear set, depending on the damage occurred. This, of course, would only be applicable if the client had a spare critical gear set in inventory. If a gear set had to be ordered, it could take from four months to two years to receive a new gear set. For example, in 2007, there was a global backlog of these types of gears sets resulting in a two year delivery. The maintenance costs associated with a catastrophic failure of this type would easily cost in the millions."

Jan 1, 2012

By Manqiu Xu, Songtao Yang, Zongfu Dai, Robert Pelton, Carla Abarca

"Fine mineral particles are difficult to process by flotation because of their low collision efficiencies with air bubbles. Decreasing air bubble size and increasing mineral particle size through flocculation are the most common approaches to improve flotation efficiencies. Herein we demonstrate that nanoparticle flotation collectors can be engineered to selectively induce fine mineral particle aggregation and promote flotation.Flotation tests of clean fine pentlandite (Pn) and Clarabelle Mill (CBM) rock tails and pyrrhotite (Po) tails that contained significant amount of fine pentlandite have confirmed that the nanoparticles can serve as both collectors and selective flocculants for fine pentlandite. In the case of clean fine Pn, the nanoparticle collectors virtually can float almost all Pn fines. Scoping tests on CBM tails have shown significant improvement in nickel recovery. Addition of nanoparticles as a flotation aid can recover 20% of the nickel contained in the rock tails and 40% of the Pn contained in the Po tails compared to current mill operations giving 0% nickel recovery from rock tails and no Pn selectivity from Po tails. Ongoing work includes attempts to identify optimal strategies for employing nanoparticles in fines flotation.IntroductionFine particle flotation is an industry-wide challenge in mineral processing. Fine mineral particles are difficult to process by flotation because fine particles have low mass and thus low momentum, which results in their low collision efficiency with air bubbles (Dai, Fornasiero, & Ralston, 1999). In addition, fine particles have not only high specific surface area but also more active surface area, which causes high reagent consumption. For base metal sulphide minerals, particle size between 10 µm and 70 µm is a typical range where high flotation recoveries can be achieved with conventional flotation chemistry and acceptable cell residence times. For pentlandite, the flotation recoveries decrease sharply when the particle size is below 10 µm and hydraulic entrainment is the dominant mechanism, giving recoveries proportional to water recovery and no Pn enrichment. (Jameson, Nguyen, & Ata, 2007)"

Jan 1, 2015

By F. D. Ford, Z. Dai, A. Byers

Manitoba Mining and Milling operations consist of three underground mines (Thompson T1, T3 and Birchtree), feeding the Thompson Mill. Three years ago, a collaborative effort involving Mines Exploration, Mines Project Development Group, Mill Technical Services and Vale Base Metals Technical Excellence Center was initiated to establish and verify the cause of high variability in concentrate quality and Ni recovery at the Thompson Mill. One outcome of this work was a program to systematically characterize the mineralogy and metallurgical performance of current and future orebodies feeding the mill. Mineralogy results show that high value enabling ores typically have a high pentlandite to pyrrhotite ratio and benign silicate mineralogy (mostly quartz and feldspar from sedimentary host rocks), while metallurgically challenging ores contain some combination of pyrite and/or hexagonal (non-magnetic) pyrrhotite and/or elevated quantities of talc (with associated carbonates) derived from altered ultramafic host rocks. The metallurgical performance of these two ore types has been simulated by an Excel particle flotation model, which calculates the relative floatability of particles based on the particle’s mineral composition and mineral locking determined from MLA images. The relationship between these mineral properties measured by MLA and metallurgical performance was established using 13 monthly composite samples from Thompson Mill. The model was then validated with results of laboratory flotation experiments on individual orebodies submitted for evaluation. The validated model can be used to predict plant metallurgical performance based on individual ore bodies feeding the mill. Individual orebody’s grade-recovery curves are assumed to be additive, and can be weighted in proportion to the mill feed to predict mill recovery over the same time period. The ore mixing can be done with a simple Excel spreadsheet and comes with a graphical output for easy visualization of the resulting grade-recovery curve.

Jan 1, 2015

By Don Thompson

It isn?t a lie if you don?t tell the whole truth The pictures National Geographic didn?t print Other photos National Geographic didn?t print?

May 1, 2009

By Kallioinen Jouko

"Advanced Flotation Technology is the application driven design of Don-Oliver flotation cells to achieve the optimum performance for each type and grind of flotation. Optimum performance is the combination of both recovery and selectivity.Optimized performance is the combined product of optimized mixing and effective froth removal. Optimized mixing is applied to roughers, scavengers, cleaners and specialty cells such as those to float hydrocyclone underflows in both primary and regrind circuits in order to reduce overgrinding. Effective mixing for fine material is easy, but overmixing reduces selectivity in frothbed.Selectivity in flotation is an important target, especially when treating complex ores, and parameters in frothbed have been examined to improve the separation of minerals and eliminate circumstances that reduce separation rate.Advances in process control have been achieved with expert controls and instructive operator information data. This has gained a higher degree of understanding of cell operation and ore type being processed to be used in future process development work. Excellent results of this Advanced Flotation Technology have been achieved and designs through 7000 cu ft (200 m3) are currently available for high capacity concentrators. This paper will detail how flotation cells are more responsive to the exact requirements of the duty specified."

Jan 1, 2000

By H. B. Sahu, N. M. Mishra, D. C. Panigrahi

The paper presents the development of a spontaneous heating liability index (SHLI) of coal based on a mathematical approach. The parameters for the calculation of this index have been determined by differential scanning calorimetric studies. Thirty-one coal samples representing both fiery and non-fiery coal seams of different ranks have been collected from different Indian coalfields and their SHLI values have been determined. In addition, the susceptibility of these samples to spontaneous combustion has been ascertained by standard crossing-point temperature measurement. The moisture percentage of all the samples has been obtained by proximate analysis. A comparative study between SHLI and crossing-point temperature, along with moisture percentage, indicates that SHLI predicts the proneness of coal to spontaneous heating more accurately.

Jan 1, 2008

By Flavio Rojos-Tapia, Samuel Sánchez-Pino, Marcelo Fernández-García, Samuel Sánchez-Baquedano, Rainer M. Imhof

"Pneumatic flotation was introduced to the Chilean copper mining industry in 1993 by Ingeniería de Minerales S.A., being implementation in 1994/95. The technology is based on the designs and development of Dr. Rainer Imhof from Germany and from Chilean copper processing experience.Pneumatic flotation has been successfully used for sulphide and oxide copper minerals and copper slag, iron ores (reverse flotation), gold and promising results with molybdenum as product. Extremely hard conditions were applied in flotation process such as roughing, cleaning, scavenging. Pneumatic flotation can be applied for any type of mineral which has to be separated by flotation. Even very dense and heavy slurries can be processed, the range of the particle sizes to be collected is very wide, and the number of cleaning stages needed normally is one in our experience until now.The good performance of the technique can be explained by the high gas hold-up and the very effective micro-turbulences which boosts the attachment to the bubbles changing dramatically the flotation time concept. Some economic high lights are: less energy consumption, less maintenance costs, simple and reliable to operate and it is required a small area to install the circuits.As a result of the Chilean mining industry experience, it can be concluded that the pneumatic flotation can be regarded as an excellent alternative to the conventional way of Mineral Processing.INTRODUCTIONDerived from seventies, works in Germany about pneumatic flotation with Prof. Simonis (Technical University of Berlin) and Prof. Bahr (Technical University of Clausthal), it has been developed an interesting flotation technology in Mineral Processing, with the designs developed by Dr. Rainer Imhof, who has been known for more than ten years (Imhof, 1998) by his contribution at Ekof, KHD, Allmineral and the actual company Maelgwyn Mineral Services where he is a Technical Director. Ingeniería de Minerales S.A. has been working ten years deeply involved with the technology developed by Dr. Imhof and is more than ten years experienced with pneumatic flotation, from Wits University and Mintek in South Africa (Sánchez, 1990), (Sánchez, 1990)."

Jan 1, 2003

By J. G. Ross

IN the paper entitled Block Caving at the King Mine (1), which was presented at the Annual General Meeting held in April, 1934, at Quebec, it was pointed out that, owing to certain conditions and financial restrictions, it was advisable to provide a temporary shaft. This was raised from the )00-ft. level to the bottom of the pit, and a 45-degree incline track was constructed up the face of the pit to surface. The temporary shaft and incline were within the ore-body, but were to be used only until such time as the new shaft-the subject of this paper-could be sunk and made ready for operation. After a careful study had been made of all available information pertaining to the ore-body, including examination of diamond-drill core records and geological data, a shaft location was selected well outside the ore-body. Further, since the crusher and dryer buildings are located over part of the ore-body, it was necessary to plan the removal of these buildings and to construct a new crushing and drying plant. This, and the new shaft, must operate in conjunction with the present mill and rock storage bin, which would continue robe used as formerly. No part of this programme, with the exception of drifting toward the shaft site, was started prior to 1937. More than usual detail on technical features is given in this paper in the hope that some parts of it may be of assistance to other members of the Institute who have to undertake somewhat similar work. The engineering and operating staff designed and supervised the work, while at the same time carrying on regular production in four mines at the rate of 12,000 tons of rock mined per day, the output at the King mine being at the rate of 140 tons per hour. No additional engineers were required.

Jan 1, 1939

By N. M. Soonawala

Detailed regional geophysical and geochemical surveys, ground surveys and drilling were undertaken to follow-up the federal-provincial Uranium Reconnaissance Program (URP) over the 27,OOO-km2 Kasmere-Munroe area in northwestern Manitoba. An analysis of the URP data showed a fair correlation between the regional airborne radiometric results and lake-bottom geochemical results, both of which also correlated with the regional geology. More detailed surveys defined anomalies with greater precision within the broad zones outlined by the URP. The ground follow-up indicated that URP anomalies can be caused by varying degrees of uranium concentration in the rocks. Mineralization of interest was found in leucogranites at several locations within the survey area. Anomalous uranium concentrations were also found in coarse pegmatites and Hudsonian granitic intrusions. It can be concluded that large-scale regional surveys can be followed up in relatively short periods of time to yield meaningful results if a properly planned exploration sequence is employed, each stage of which successively narrows the area of interest.

Jan 1, 1979

By Mark Aylmore, Guy Deschenes

"Increasing pressure are motivating the gold mining industry to develop a substitute to cyanide for leaching gold. This effort in mainly based on the high toxicity of cyanide and on the lack of efficiency of cyanide in the treatment of mildly refractory gold ores (sulfides and pre-robbing). Consequently, in only a few years, consortia have been created to elucidate and implement a new technology. The most promising lixiviant that has been selected to replace cyanide is thiosulfate. This paper will present a critical analysis on the latest developments in thiosulfate leaching and illustrate the potential and limitations of the technology with experimental data. Finally an assessment of the cost and performance of thiosulfate leaching relative cyanidation will be evaluated.INTRODUCTIONConcerns regarding the toxicity of cyanide and inability of cyanide solution to effectively leach some carbonaceous gold ore or mild refractory gold ores have made the gold mining industry evaluate alternative lixiviants to leach gold. This concern has been heightened recently by the cyanide spill at a mine in Romania, which devastated a 250-mile stretch of the Danube River and its tributaries, and the environmental damage at Ok Tedi mine in Papua New Guinea. Some countries and locations have prohibited the application of cyanidation to recover gold, such as, California and Colorado States, Japan and Turkey etc.There are several potential non-cyanide lixiviants (Sparrow and Woodcock, 1995) for gold extraction, such as thiosulfate, thiourea and halogen. A pilot feasibility test (Marchant and Broughton, 1987) had suggested that thioureation might result in acutely toxic byproducts even after treatment. Scientists of Swedish Academic of Sciences reported that thiourea is a carcinogen. Halogen is also a pollutant to the environment. Thiosulfate leaching appears to have very good potential as an effective and less hazardous procedure for gold and silver extraction from auriferous ores. In addition to being much less toxic and relatively cheap, it forms a stable anionic complex with gold but is less reactive to other metals, for instances, copper and carbonaceous materials, in comparison with cyanide."

Jan 1, 2001

By Phil Keele

Canadian Natural ??Business Approach Efficiency and Execution ?Drive to be the low cost producer ?Focus on exploitation ?Augment exploitation with strategic acquisitions ?Maintain Discipline and Strength while Delivering on the Defined Plan ?Maintain flexibility and control allocation of capital ?Strive for balance (asset portfolio) ?Maintain financial strength

May 1, 2010

By Marc C. Bétournay

A mine production locomotive, the world?s first applied industrial fuelcell vehicle, has been designed and tested in the context of a number of proof-of-concept projects supported by the Fuelcell Propulsion Institute, an international consortium of stakeholders dedicated to facilitate the commercialization of fuelcell vehicles. The locomotive?s simple electric-powered motor and controller system was ideal to study a number of requirements related to fuelcell power application: hydrogen power plant operation, underground hydrogen use, risk and regulatory requirements, production performance versus the conventional battery-powered locomotive version under measured duty cycles and production requirements, power plant design improvements for other fuelcell vehicles, and cost-benefit aspects. This article will focus on the design and testing aspects of this project which has led to successful performance demonstrations of the vehicle under surface and underground conditions at two mines. It will also present information on the creation of a safe, reliable and efficient power plant which fulfilled its design objectives, including longer productivity time for a given vehicle fill-up.

May 1, 2003

By Andréa Lagacé

"The milling of sulphide ores inherently generates “thiosalts”, a series of partially oxidized sulphur oxyanions (S2O3 2-, S3O6 2-, S4O6 2- etc.), which make control of effluent treatment systems difficult because their natural oxidation produces acid with the potential to lower the pH within the treatment system and/or receiving environment.At the Xstrata Copper Kidd Metallurgical Site, thiosalt oxidation in the Tailings Management Area continues after buffer storage Ponds A and C where lime is added to precipitate metals and elevate the pH to within the required range for discharge. If the additional acidity generated during the continued process of thiosalt oxidation is not neutralized there is a risk that the final effluent will be non-compliant with regulated standards.To mitigate this risk, in 2007 a full scale pilot trial was conducted with hydrogen peroxide in order to force the complete oxidation of thiosalts prior to the lime treatment stations. This method of chemical oxidation had been shown to be effective at Xstrata Zinc’s Brunswick Mine. The pilot results indicated that a maximum of 50% of the stoichiometric quantity of hydrogen peroxide is required to reduce the thiosalt concentration in the No. 2 thickener overflow stream (feed to buffer storage Ponds A and C) to less than detection (10 mg/L); however, treatment was only effective in the presence of a 20 mg/L iron (Fe) catalyst. Since the hydrogen peroxide addition point at the No. 2 tailings thickener overflow typically contains <1 mg/L total Fe, a second reagent, ferric sulphate, was used to increase the total Fe concentration to the required level. This paper describes the set-up and results of the pilot trial which were used in the design of the full-scale plant.INTRODUCTIONTailings Management Area OverviewXstrata Copper’s Kidd Metallurgical Site, located in Timmins, Ontario, is an integrated metal refining facility producing copper, zinc, cadmium, indium, liquid sulfur dioxide, and sulfuric acid from third party custom feeds, and mineral concentrates recovered from its 7,800 tonne per day mill."

Jan 1, 2010

By B. McLaughlin

"The Penna shaft is the deepest single-lift shaft in North America. Agnico-Eagle started sinking the Penna shaft in 1995 with a hoisting plant capable of hoisting 1800 t/d from a 2240-m deep shaft. Exploration success at depth led to the replacement of the existing double drum hoist by another double drum hoist capable of hoisting 7000 t/d. The use of another double drum hoist, instead of a Blair multi-rope winder, to hoist 24.5 t skips was only made possible by lowering the safety factor.This paper describes recent experiences at Penna and in South Africa, and examines the possibility of extending the double drum hoisting system to a depth of 3 km. IntroductionThe original Penna production hoist was a 4.88 m (16 ft) diameter double drum and single clutch machine. Béliveau (1996) and Scott (1996) have described this hoisting plant. In 1998, a decision was made to increase mining capacity from 1800 t to 4500 t of ore per day from the shaft bottom. Final capacity had to include an allowance of 1800 t of waste per day for future capital projects. While daily capacity was to be 6300 t, it would, by taking into account the different rock densities, be equivalent to hoisting 7000 t of ore.The steps taken to lower the safety factor were presented by McLaughlin and Scott"

Jan 1, 2004

By Q. Liu, P. Katsabanis, J. A. Meech

A thermohydrodynamic computer code has been used to simulate dust explosions. For sulphide dusts, the thermodynamic predictions are used to investigate the effect of dust concentration, mineral content and inert materials as well as the quantity of sulphur dioxide produced. It was found that the amount of oxygen available for the explosion is very important and that the dust concentration which gives maximum explosion pressures is obtained at zero or slightly negative oxygen balance values. The sulphide minerals were found to have the following explosibility sequence: pyrrhotite, pyrite, chalcopyrite, sphalerite, covellite, chalcocite and galena, which is in agreement with mine experience. The results show that theoretical calculations can be used to predict explosion pressures and toxic gases produced by a dust explosion and therefore they can assist in the design of protective measures .

May 11, 1988

By Caroline B. Chapleau, Mélanie Proulx, Claude Bazin, Gaétan Lavoie

"Quebec Cartier Mining operates a pelletizing plant in Port-Cartier, QC. Grinding, agglomeration and pellets induration are the three main steps in the preparation of iron oxide pellets. In 1998, following different recommendations, the company increased the speed of one of its ball mill in order to increase the grinding efficiency of the machine. As expected, the increased speed lead to an increase of the power draught, which did not produce the expected increase of fineness of grind, neither its allows to increase the mill throughput. The change of behaviour of the mill could hardly be understood by comparison of discharge size distribution at initial and modified mill rotation speed. On the other hand, the use of the selection function from a population balance model provides an insight of the changes that occurred in the mill. This paper reviews the various steps required for the estimation of a grinding mill selection function. Results of the calibration to Quebec Cartier grinding mills show that the increase in the mill speed leads to higher rate of breakage of coarse particles, at the expenses of less efficient breakage of medium and fine size particles. In the case of the studied mill, breakage of coarse particles was probably not the critical step of the mill operation. INTRODUCTIONOre size reduction is the major energy consumption step in any mineral processing operations (Austin et al., 1984). Size reduction is required to either liberate valuable minerals from the gangue minerals in which they are imbedded, or to increase the specific surface of the ground material. Plant engineers continuously face the challenge to find grinding machines, operating conditions or grinding circuit flowsheet configurations that could improve the size reduction process at lower energy or m6dia consumption."

Jan 1, 2000

By Phillip Cancilla, Daniel Roy, Frank Rosenblum

"The manual moisture determination methods employed today by mineral processing plants falls short in providing timely information required for automation control. The costs associated with transporting and handling concentrates still represent a major portion of the overall treatment price. When considering the cash flow of a mining operation, that is governed by both the smelter contract, with moisture penalties and the quantity and quality of the concentrates shipped, an efficient method of on-line moisture content would be a welcome tool.A novel on-line determination system for ore concentrate moisture content would replace the normally tedious classic manual procedure. Since the introduction of microelectronic-based control systems, operators have strived to reduce the treatment costs to the minimum therefore a representative and timely determination of on-line moisture content becomes vital for control set points and timely feedback. Reliable sensors have long been on the “wish list” of mineral processors since the problem has always been that you can only control what you can measure. Today, the task of moisture determination is still done in the classical technique of loss in weight by uncontrolled procedures. These same methods were introduced in the earliest base metal concentrators. Generally, it is acceptable to have ore concentrate moisture content vary within a range of 7 to 9%. Many times, delays in manually achieving reliable feedback on the moisture content results in the moisture varying from 5 to 12% before corrective actions can be made.This paper first reviews the traditional and widely available methods for determining moisture content in granular materials by applying physical principals and properties to measure moisture content. All methods are in some form affected when employed on mineral ore concentrates. This paper describes a unique and promising on-line moisture sensor in two mineral processing applications, which not only automates the tedious tasks but also results in reliable moisture feedback that can be used in the optimization of the de-watering process equipment such as pressure or vacuum filters and fuel-fired driers. Finally, two measurement applications will be presented to indicate the usefulness and to summarize the measurement requirements for the proposed method of employing drag force and mechanical properties of the material itself to determine the moisture content."

Jan 1, 2001

By E. L. C. Martins, M. J. Nicol, D. Majuste, A. D. Souza

The effects of organic compounds on the current efficiency (CE), morphology, crystal structure and mechanical properties of the metal deposited during the electrowinning of zinc are described. A flotation collector and lubricating oil were selected based on observations made during the industrial production of zinc from silicate ores, in Brazil. The analysis by Fourier transform infrared spectroscopy of these compounds, which may be present in minor amounts in the electrolyte solution, indicated the presence of a polar amine group in the collector, while the lubricating oil is a non-polar compound. The average CE value obtained from organic-free industrial solution was 91.15 ± 0.26 %. The CE dropped to 54.35 ± 0.73 % in the presence of 100 mg·L-1 of collector in the solution, and a negative effect was also observed in the presence of similar amounts of oil (88.84 ± 0.61 %). The characterization of the deposits by scanning electron microscopy and X-ray diffraction revealed the formation of pores in deposits obtained from solutions containing the oil, while a different growth pattern (perpendicular zinc platelets) was identified when the flotation collector was added to the industrial solution. In the presence of these contaminants in the solution, guided-bend tests revealed that the deposits have a higher resistance to deformation, but lower ductility, properties that may affect the performance of the stripping stage. As a result of this work, simple control and optimization actions were applied in the industrial plant, which resulted in important improvements in the electrowinning process.

Jan 1, 2014