Search Documents

By R. Esteban, D. Runnels, S. Girgin, J. Torrealba-Vargas

"Each mineral processing project requires early testwork to evaluate the economic potential of a deposit. The testwork needs to be efficient and it should provide enough information to obtain key parameters, first for a high level flowsheet selection at the conceptual and PEA stages and then, for later stages, to confirm the flowsheet selection and optimize the metallurgical efficiency of the plant. The testwork should consider all rock types or lithologies present, and carry out testwork for the purpose of sizing the major processing equipment.A successful project requires that the project stakeholders develop an efficient sample collection program to produce enough material for a scoping and pre-feasibility level program. This involves the participation of a team of geologists, mining and metallurgical engineers in the project, as early as possible, to define the deposit characteristics that need to be validated.The project schedule requires a close control of the testwork scope, procedures, and timing, but also the efficient analysis of results to provide indications of red flags that could impact circuit design as early as possible.In some cases, projects are put on hold due to fluctuations of the world economy until the return of more favorable conditions. In that scenario, prior data analysis of former testwork results could reduce significantly the amount of testwork required to restart a project. The paper will also present examples where the analysis of former testwork data was used to reduce the amount of new testwork in addition to presenting examples of latest projects where the above-mentioned test program approach was followed."

Jan 1, 2016

By Gerhard W. Heinrich, Gerald V. Schroeder, Daniel A. Murphy, Daniel F. Suarez, Jamie B. Beauchamp

"Washwater 'Finger' sprays were installed and tested in the copper/nickel separation circuit at Strathcona Mill to improve flotation capacities and related metallurgical performances. The new spray design features submerged sideways introduction of wash water into the flotation froth through nozzles at the end of vertical pipes which are suspended from a header above the froth. This maximizes the effective cross sectional area of flotation vessels while maintaining effective froth cleaning and a desirably high density of the concentrate slurry. The plant tests gave increases of copper concentrate production rates of 17% to 20% for conventional cells and 16% to 20% in column flotation at target grades of 29% to 30% copper and of less than 0.5% nickel. Basic considerations and concepts of tests and evaluation procedures are described.IntroductionMeeting flotation concentrate grade targets at maximum production rates and recoveries is a challenge all too familiar to operators of base metal ore concentrators. Frothwashing is an option to improve grade/recovery performance by minimizing entrainment of impurities into the concentrate, which is commonly known since the sixties (Kaya & Laplante, 1989). It has been recommended for the flotation of sulphides and industrial minerals alike (Kaya & Laplante, 1989; Miller, 1969; Heinrich, 1989) and has found its ultimate application in flotation columns (Finch & Dobby, 1990). The washwater addition in a flotation column is most evenly distributed over the column's cross-sectional area thus ensuring almost complete displacement of feed water from the froth by a countercurrent washwater flow -provided, a positive bias is maintained. Therefore, flotation columns are ideal for cleaning flotation. However, there is usually less room for boosting the concentrate production capacity by increasing airflow or slurry level then with conventional cells because of the smaller cross-sectional area available."

Jan 1, 1994

By A. G. Beer

The evolution of microstructure is examined during the annealing of hot worked magnesium alloy AZ31. The influences of deformation and annealing conditions on the developed microstructures are assessed. It is found that annealing at a low temperature (300 °C), after deformation at a low temperature and strain rate (300 °C and 0.001 5-1 respectively), results in the development of abnormally large grains. With increasing values of Z (lower temperatures, higher strain rates), static recrystallization of the dynamically recrystallised structure takes place; smaller annealed grain sizes are attained and the time at which coarsening begins is reduced. Whilst both the deformation and annealing conditions influence the time it takes to reach a stable annealed microstructure, the grain size attained is governed solely by the prior deformation conditions employed.

Jan 1, 2006

By H. Houali

Corrosion is an electrochemical process that causes degradation and deterioration of various steel works (pipelines, drains, cisterns) whether they are buried, immersed, or not. Worldwide, we estimate that corrosion destroys a quarter of the annual production of steel at a rate of 5 tons per second. Several techniques are used to protect against corrosion. Among these processes, Cathodic protection, which is regarded as the best technique to assure the protection of steel, works against this phenomenon. This is achieved either by a system of reactive anodes, or by the technique of impressed current protection or other techniques. Before any installation of cathodic protection, a preliminary study and pre-evaluation of certain parameters must be made. In the present work, we will present an example of dimensioning of an installation of cathodic protection by imposed current of a pipeline using solar energy, where we discuss the following items: ? Evolutions of the potential as well as current along the pipeline and their respective expressions deduced from the laws known as telegraphists; ? Range of protection (potential of protection along the pipeline); ? Influence of the isolation resistance of the coating on the range of protection; Effect of the aging of the coating and its influence on the current of protection

Jan 1, 2005

By Y. Miyabayashi, K. Nishikawa, H. Nagai

JX Nippon Mining & Metals Group recovers valuable metals from end-of-life electronic products in an economical and environmentally-benign way, based on technologies that have been acquired in mining, smelting, and refining operations over time. End-of-life electronic products contain halogens and hydrocarbons. When such materials are treated in the copper smelting process, corrosion of equipment and discoloration of sulfuric acid occur. As a countermeasure to these problems, we have developed pretreatment processes that include an incinerator, exhaust gas washing towers, and a defluorination facility. By implementing these improvements, we have been able to treat a large volume of end-of-life electronic products efficiently in the copper smelting process.

Jan 1, 2014

By H. Perez, A. Lavoie, V. Prévost, P. Létourneau, P. Lind

The Home smelter is a custom copper smelter located in Rouyn-Noranda, Quebec. In 2005, the smelter produced 145,000 t of copper containing 807,000 oz of gold, 20,388,000 oz of silver in addition to 515,000 t of sulphuric acid. Recently, a flexible flow sheet has been developed incorporating the intermittent use of the Noranda Continuous Converter allowing for the increasing or decreasing of production based on market conditions, while attaining 90% or greater sulphur fixation regardless of operating mode. For 2006, the smelter is operating in full production mode and production is expected to be approximately 185,000 tm of copper. Mechanical modifications, process changes, metallurgical concepts, minor element treatments, and operational techniques that have allowed the smelter to develop this flexibility are presented. Current efforts to increase the productivity of the converter aisle and anode furnaces as well as improvements being made to address fugitive emissions are also discussed.

Jan 1, 2007

By Chris Brothen

The introduction of new technology in mine operations has provided real opportunities for increased efficiencies and production gains which translate into enhanced profits. Computing and network technology usage has become integrated into surface mining operations and on average these investments in technology have proven beneficial for efficiency and productivity improvements. Embracing new technologies however, does not guarantee positive results. The expectations or improvements derived through the technology must be confirmed and clarified well before implementation. Tire Pressure and Temperature Monitoring Systems are an excellent example of an existing technology that can provide full time automated performance measurements of tires operating under harsh conditions and environments. Prompt warnings or alarms signaling when a tire has exceeded operating capacities will provide savings through lowered maintenance costs and increased productivity. To truly quantify the projected savings in tire life, fuel consumption, and increased levels of production, all costs associated with the technology, both direct and indirect must be considered. Apart from the initial cost of the system implementation, ongoing maintenance and support costs must be considered as well as the costs of system integration into existing mine operations

May 1, 2008

By L. Tang

A seismic monitoring system was installed in 2005 at Dongguashan Copper Mine, the deepest metal mine in China. Based on the seismic events monitored in situ, the possibility of rockburst prediction and prevention is investigated in this paper. The characteristics of space-timeintensity of mining-induced seismicity and the seismic response to mining are studied in detail using the seismic data in Dongguashan Mine. A conceptual model and a criterion of assessment of hazard seismic nucleation are proposed for Dongguashan Mine. In this model, the mine seismic stiffness method is adopted for rockburst prediction within the framework of the unstable failure theory. To analyze rock failure cases in Donggauashan Mine, the rate of the ratio of stiffness of rock in nucleation area to its surrounding area is proposed as a criterion for rockburst prediction.

May 1, 2009

By P. E. Walker, M. E. Reed, R. C. Sims, B. Snowdon, D. E. Fallas

An advanced Flash Furnace feed system is the key to improving furnace performance. Clyde-WorleyParsons has developed a revolutionary pulseless pneumatic injection feed system technology, capable of delivering a range of benefits to operators of Flash Furnaces. The solution was created by combining the pneumatic conveying and injection knowledge, expertise and technology of Clyde Materials Handling with WorleyParsons' flash furnace process and operating experience. Optimal furnace burner performance requires the feed material to be presented to the burner as a stable, pulseless and accurately controlled flow, distributed evenly around the burner tip circumference. These simple requirements appear obvious, but are extremely difficult to satisfy in industrial environments and are not achieved by conventional feed systems. Our analysis of existing operating furnaces has identified the link between pulses in concentrate feed rate caused by conventional drag chain conveyors and rapid fluctuations measured in the furnace pressure. These fluctuations occur at a timescale close to the reaction shaft residence time and lead to unwanted instability in the primary furnace reaction zone - the flame. Through the use of the solution created by Clyde-WorleyParsons, it is predicted that the much more accurate control of feed rates achieved can lead to substantial improvements in furnace output, increased oxygen efficiency and better control of the composition of furnace liquids, such as matte, blister or slag. All these improvements lead to significant increases in smelter output and efficiency, and deliver high economic value compared to the cost of the feed system. Clyde-WorleyParsons' solutions can be deployed on greenfield sites or retrofitted, and therefore, have the capability to improve feed control at both new and existing smelters. This paper will discuss the field test work undertaken to date, the impact of findings and the ongoing analysis of linkages between instabilities in the various components of conventional feed systems and furnace pressure stability.

Jan 1, 2007

By P. H. J. Mercier, M. Couillard

Aberration-corrected scanning transmission electron microscopy (STEM) allows for the nano-scale exploration of materials at unprecedented resolution and sensitivity. In this paper, we combine this approach with electron energy-loss spectroscopy (EELS) and energy dispersive X-ray spectroscopy (EDX) to analyze the carbon distribution in residual solids found in solvent-diluted bitumen product extracted from Alberta oil sands. Major components of these contaminant solids are ultrafine clays. Biwettable clays have been associated with the formation of solid-stabilized water-in-oil emulsion, which are known to increase the content of both water and mineral solids in the final bitumen product. We demonstrate that the residual solids present in bitumen product contain carbon intermixed with mineral particles of various size and shape. By probing the carbon content at the nanometer scale with the high chemical sensitivity of EELS, we provide direct evidence of carbon intermixing with clay platelets. This clay-organic association at the nanometer-scale will contribute to the biwettable, hydrophobic character of the platelets, and will therefore play a crucial role in the bitumen extraction process

Jan 1, 2014

By Cheryl L. Allen

The increasing energy costs associated with mining has become an issue that needs to be addressed for future sustainable production. Vale Inco is undertaking a Ventilation on Demand (VOD) Project in an effort to minimize costs, continue to mine at depth and reduce green house gas emissions. A dynamic VOD system is very complex with potential high risk. Therefore, a systematic approach is being taken for successful development and implementation of the concept. The physical components of the system are currently being tested at various Vale Inco mine sites. While the operability of the physical components are being tested, the strategy for optimizing the architectures of the system is being defined. This presentation discusses the method of developing a VOD system at Vale Inco.

Feb 1, 2008

By T. Gonzales, M. Maleki, M. Caçador, B. Climenhaga, H. Ghorbani

The campaign life of furnaces in the copper making industry is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper monitoring and assessment of the existing conditions and safe remaining life of the vessels and their refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a typical fitness-for-service assessment of a rotary vessel shell in order to extend the campaign life of copper making furnaces and enhance safety. The furnace refractory management system involves a comprehensive audit and monitoring program which has been successfully applied to several copper flash smelting furnaces over the past 15 years. The fitness for service assessment provides a methodology to estimate the remaining life of the steel components by evaluating the existing damage and future damage rate based on the historical survey data. The above practices can provide the operator with cost savings by extending the vessel campaign life in lieu of implementing more rigorous refractory lining and shell audits. INTRODUCTION Primary copper smelting is generally divided into two categories of flash smelting and open bath smelting. There are many different types of vessels that can be used to convert the copper concentrate to blister copper including, flash, Mitsubishi process, TSL (ISA/Ausmelt), SKS Bottom Blowing, Anode and Teniente/Noranda furnaces, reactors, and Peirce Smith converters. Each vessel has its own complex and intense environment which requires careful refractory and steel design to withstand the severe thermomechanical and thermochemical attacks within its campaign life. The campaign life of furnaces is greatly affected by damage caused by normal operation cycling and abnormal conditions. Proper assessment of the existing conditions and safe remaining life of the vessels and/or refractory lining is key to prevent an unplanned early replacement. This paper presents an industry-proven refractory management program as well as a fitness-for- service assessment methodology to estimate the remaining campaign life of copper making furnaces resulting in cost savings and enhanced safety of the operating vessels.

Jan 1, 2019

By P. Woo, N. Brodusch, R. Gauvin, H. Demers

The scanning electron microscope (SEM) was primary developed for imaging applications. With the introduction of the Si(Li) energy dispersive spectrometer (EDS), simultaneous imaging and x-ray microanalysis became possible. However, long working distance and high current were needed because the position and small solid angle of the EDS detector. The high spatial resolution is generally obtained at short working distance with a SEM. Unfortunately x-ray microanalysis is never performed in the best imaging conditions. The annular silicon drift detector system is inserted below the objective lens which gives a higher solid angle (up to 1.3 sr). In consequence, a lower working distance and probe current can be used. An improved spatial resolution becomes possible during x-ray microanalysis. With this x-ray detector installed on a cold-field emission scanning electron microscope, quantitative x-ray microanalysis with high spatial resolution at low beam energy and low current becomes possible with the possibility of using the various different type of imaging at the same time. Also, since the count rate can be as high as 1,500 kcps, which lowers significantly the detection limit of elements as well as the minimum feature sizes of different phases that can be distinguished.

Jan 1, 2014

By B. Garitte, O. K. Mahabadi, P. Marschall, A. Lisjak, H. R. Müller, T. Vietor, G. Grasselli

Numerous research studies have shown that clay rock formations exhibit favourable characteristics for the deep geological disposal of radioactive waste. However, one main concern is that the favourable long-term isolation properties of the intact rock mass could be negatively affected by the formation of an excavation damaged zone (EDZ) around the underground openings. The goal of this paper is to present new rock mechanics insights into the phenomena involved in the EDZ formation and evolution processes in Opalinus Clay, a clay shale currently being assessed as a potential host rock for an underground repository in Northern Switzerland. More specifically, discontinuum-based computer simulations, using a hybrid finite-discrete element method (FDEM) approach, were applied to two case studies considering circular excavations in an anisotropic Opalinus Clay formation. In the first case study, numerical modelling was applied to the HG-A experiment, a long-term in-situ test carried out at the Mont Terri underground rock laboratory to investigate the hydro-mechanical response of a backfilled and sealed microtunnel. A mechanistic analysis of the fracturing processes involved in the EDZ formation was carried out. In the second case study, the long-term effect of the bentonite backfill swelling on the EDZ around an emplacement was numerically analyzed. Overall, the simulation results highlight short-term distinctive rock failure kinematics due to the bedded rock structure, as well as a long-term reduction of the excavation-induced fracture porosity in response to mechanical loading.

Jan 1, 2015

By Frands Jensen, Erik Eriksson

"Haldor Topsoe’s Wet gas Sulfuric Acid (WSA) technology has been proven in a number of industries converting sulfurous gasses to concentrated sulfuric acid. In the metallurgical sector plants have been delivered handling SO2 gasses from copper, zinc, molybdenum, and lead ore. WSA has high energy efficiency and allows autothermal operation from feed gas strengths as low as 3.0% (volume). Recent variants of the WSA process have been developed that allow very high SO2 conversion efficiencies of over 99.9%. This paper describes the technology, its advantages and industrial achievements.The WSA technology is well suited for production of concentrated sulfuric acid of commercial quality from the sulfur dioxide (SO2) gas that inevitably emerges from the metallurgical processes. Some of the features that make the WSA technology attractive for this application are:- High SO2 conversion rates (up to 99.99%)- High energy efficiency leading to a low autothermal point (~ 3% SO2)- No need for gas cooling and drying to produce concentrated sulfuric acid- No production of waste- Very low cooling water consumptionThis paper describes the WSA process principles and highlights features that make this process attractive for handling SO2 gases."

Jan 1, 2014

"Sink-float analysis is often used to obtain yield-ash and density partition curves in the coal industry. These provide a valuable tool for evaluating the performance of a separation process. However, for dense minerals, obtaining complete grade-recovery and density partition curves is more difficult due to the lack of heavy liquids available with the required densities. This paper examines a potential solution to this problem which is to perform batch fractionation of mineral samples in a laboratory-scale REFLUX™ Classifier using high viscosity fluidising liquids. The REFLUX™ Classifier is a gravity separation unit consisting of a system of parallel inclined channels positioned above a vertical fluidised bed. Operated in semi-batch mode, a charge of particles is fluidised from below and particles up to a certain density are elutriated from the top of the system. The fluidisation rate is then increased incrementally to fractionate the sample at progressively increasing densities. Previous work by Hunter et al. (2014) and Iveson et al. (2015) has shown that this method provides excellent agreement with yield-ash and partition curves for coal, especially when glycerol solutions are used as the fluidising liquid. This approach has now been extended to obtain the grade-recovery and density partition curves of high density mineral samples. This method has the potential to provide the minerals industry with an effective tool to evaluate the performance of unit operations separating at cut points higher than the available heavy liquids.INTRODUCTIONMeasuring efficiency and effectiveness is of key importance in the continuous improvement of mineral processing plants. For density based separation, one way the performance of a process can be evaluated is the measurement of density-based partition curves. Currently, this is done in the coal industry using the sink-float method, where heavy liquids are used to fractionate particles into discrete density intervals. However, with high density minerals such as iron ore, liquids of sufficient density are rare, and in most cases also pose serious health and safety concerns to laboratory operators. Most commercial laboratories do not perform sink-float separations above a density of about 4400 kg/m3, the maximum density of Clerici solution without operating at excessive temperatures (Koroznikova, Klutke, McKnight & Hall, 2007; Rosenblum, 1974)."

Jan 1, 2016

By A. Bendada, P. Servais, X. P. Maldague, C. Ibarra-Castanedo, C. Mohr

Infrared (IR) thermography is a nondestructive, non-contact and non-intrusive technique that allows the fast inspection of large and complex structures with limited accessibility. Pulsed thermography is particularly interesting for the inspection of aerospace materials such as composites given that, after submitting the specimen surface to a thermal front, the most common types of subsurface discontinuities (e.g. porosity, de laminations, dis bonds, fiber breakage and inclusions) can be detected with an IR camera as regions showing abnormal temperature patterns. We present first the case of an aircraft door with water ingress and surface repairs on its honey comb structure. We also highlight the advantages and limitations of thermography for the inspection of aircraft composite parts, such as edge flaps, rotor blades and speed breaks. Finally, we expose some results from a Kevlar® non-planar specimen with Teflon® inclusions at different depths and locations.

Jan 1, 2006

By S. B. Mishra

Ni-20Cr metallic coating was deposited on a Ni-based Superalloy (3Fe-19.5Cr¬0.3Ti-Balance Ni) by a shrouded plasma spray process; NiCrA1Y was used as a bond coat. Erosion studies were conducted on uncoated and plasma-spray coated superalloy specimens using an air-jet erosion test rig at a velocity of 40 m/s and impingement angles of 30° and 90°. The coating has been characterized for porosity, microhardness and microstructure and X-Ray Diffraction (XRD). An electron probe micro analyzer (EPMA) was used to obtain X-ray elemental mappings of the coating along the cross-section. Scanning electron microscope (SEM) with EDAX attachment was used to analyze the eroded surfaces.

Jan 1, 2005

By A. de Ville d’Avray, G. Guezennec, P. Wavrer, E. Braak

The aim of the European CEReS project was to develop an innovative copper recycling route based on the coprocessing of coal production waste by bioleaching and printed circuit boards (PCBs) from Wastes of Electrical and Electronic Equipment (WEEE). Coal waste is processed by bioleaching in stirred tank reactors, and the resulting bio-lixiviant solution is used to extract copper from PCBs pre-treated by catalytic cracking. Copper is then extracted using solvent extraction, stripping and electrowinning. The whole process flowsheet combines thermal, biotechnological, physical and hydrometallurgical operations. Once the process concept has been validated at laboratory scale, a simulator of the whole process has been built in the USIM PAC software platform. The tool enables to improve the analysis of the results of the lab-scale experiments and to design industrial-scale scenarios by simulation. The results of such simulations allow to estimate the economical interest and to perform environmental impact assessment. After presentation of the CEReS project objectives and main results, the paper describes the methodology used to build the simulator and define the scenarios corresponding to feasible process routes. The main results of the simulations are then presented with technical, economic and environmental point of views. INTRODUCTION Because of rapid technological innovations in the electronics industry, electronic waste represents the fastest growing waste stream in the world, especially in developing countries (Işildar et al., 2018). Meanwhile, the global copper demand is expected to go on rising in the future. As significant amounts of copper are present in end-of-life printed circuit boards (PCBs), it becomes a necessity to develop efficient copper recycling routes. Metal refining from e-waste is traditionally performed by pyrometallurgical processes. However, the hydrometallurgical processing of PCBs, which has been shown to be technically feasible at laboratory scale with a wide range of leaching reagents, could be a less energy intensive and more flexible alternative (Tuncuk et al., 2012). However, a large amount of leaching reagent is required to leach the metals from PCBs.

Jan 1, 2019

By A. Malfliet, A. Van den Bulck, D. Willems, M. Guo

The feed stock of copper fire refining processes consists of two major constituents: blister copper and high-Cu secondary scrap. A large fraction of this secondary scrap, originating from urban mining, is quite high in impurities such as Fe, Ni, Pb and Sn. Problems arise in electro-refining when these elements exceed certain limits. As a consequence, transformation of the secondary copper raw materials into high grade copper has become troublesome. However, the behavior of impurities relevant to fire refining conditions, essential for anode refineries, has not been studied in detail. Furthermore, limited research has been performed on the distribution of Ni between copper metal and slag. In this study, equilibration at 1300°C of liquid Cu-1wt.% Ni alloy and CaO-CuOx- FeOy-SiO2 slag in vacuum sealed quartz ampoules was performed for 12 hours, followed by water quenching. Electron Probe X-ray Microanalysis was employed to investigate the composition of the equilibrated alloy and slag. The distribution coefficients of Ni between slag and alloy were determined as a function of oxygen partial pressure and CaO concentration. INTRODUCTION Europe’s initiatives for a circular economy, pushing for resource-efficient ways for a sustainable future, puts Europe at the forefront of the globe. In Europe, 50% of the copper originates from recycling, being an excellent example of Europe’s circular economy (Juncker, 2018; Lacasse, 2018). High-grade copper recyclates are made available which regularly contain impurities like Fe, Ni, Sn and Pb. Aurubis Belgium is responsible for recycling these types of recyclates to anodes, cathodes and copper products. However, after fire refining of copper, the aforementioned impurities remain in the anode copper, leading to problems in electrorefining. During the fire refining of copper, a CaO-“Cu2O”-“Fe2O3”-SiO2 slag is used. Fundamental information of the distribution of impurities between the copper and this slag system is therefore essential to understand and improve the copper fire refining process at Aurubis Belgium.

Jan 1, 2019