Search Documents

By P. Reyes

The start up and operational optimization of the No. 3 Oxygen Plant at the Caletones Copper Smelter of the Codelco - Chile El Teniente Division is summarized. In addition, the economic impact of such optimization on the production cost of oxygen and others aspects associated to the operational robustness as well is detailed.

Jan 1, 2007

By Chri Rule

"This paper tells the story of the rapid commercial application of stirred milling technology at Anglo American Platinum’s many Concentrators. The first stirred mill – a 10 000 litre IsaMillTM; the largest at the time, was commissioned in late 2003. The project development work was presented at SAG 2001. This operation was “proof of concept” and vindicated the decision to scale up the technology; allowing a rapid and extensive roll-out of mainstream regrind mills as well as several further flotation concentrate regrind mills, over the next six years.Currently 23 stirred mills are in operation with 64 MW of installed drive capacity – this paper describes the projects’ roll-out and the significant results achieved to date. Many operational problems have been solved along the way, some of these will be described. The introduction of the technology has seen a step change in metallurgical results and progressively decreasing operating costs."

Jan 1, 2012

By H. R. Manouchehri, A. Weh

"High voltage electric pulse comminution (SELFRAG) relies on inducing electrical breakdown that occurs when the resistivity of a dielectric is insufficient to completely block all transfer of electricity while the conductivity is not high enough to fully accommodate the flow of electricity without considerable changes to the crystal lattice. The technology is based on introducing the electrical discharges into solids immersed in water and placed between two electrodes. The technology has received significant attention since investigations have revealed the potential for fully fragmenting particles or pre-weakening rocks in order to reduce the energy consumption in comminution practices, improve liberation and potentially increase the recovery in mineral processing. Mineralogical analysis of samples showed possible liberation at coarser sizes by high voltage breakage in comparison with conventional mechanical comminution.This study explored the potential of implementing SELFRAG to treat the Sandvik’s Mittersill mine tungsten ore (scheelite) for recovery improvement. Accordingly, standard SELFRAG tests were conducted on four samples from the tungsten process plant to evaluate the energy-breakage relation and potential to liberate the value minerals at coarser size fraction for recovery improvement. The size reduction of the ore after processing with SELFRAG revealed that size deportment occurs at 0.4, 0.2, and 0.1 mm, which indicated potential liberation of gangue and target minerals at respective sizes. In comparison with conventional milling, the difference is the deportment of values into 0.4 mm sizes, which was, to some extent, confirmed by SEM liberation analysis. However, more tests are needed to proof the concept. The study has indicated that, despite consuming more energy in comparison with conventional mechanical comminution, there are promising prospects in liberating the values at coarser fraction and improve recovery by making use of SELFRAG. The energy consumption can be reduced through customized generator and equipment setup, which must be further investigated."

Jan 1, 2016

By A. W. F. Smith, P. B. Prangnell, D. N. Crowther, P. J. Apps

It is well known that the refinement of grain size in metals leads to a significant improvement in important mechanical properties. As part of a European collaborative project, processing schedules have been investigated aimed at producing a homogeneous ultra-fine ferrite and spheroidised carbide aggregate microstructure structure in high carbon (CMn) steels (0.6-1.2wt%C), via conventional 'warm' rolling and innovative Equal Channel Angular Extrusion (ECAE). Suitable deformation schedules were determined from dilatometry and thermo-mechanical Gleeble simulations. Evidence of an ultra-fine ferrite and carbide aggregate microstructure following 'warm' rolling is given. A significant improvement in tensile strength, particularly proof stress (0.2%) was also noted in comparison to material deformed at higher temperatures. Concurrent Equal Channel Angular Extrusion (ECAE) experiments investigated microstructural evolution with incremental strain. Extensive analysis was carried out using various techniques, including high resolution Electron Back Scattered Diffraction (EBSD). Evidence of ferrite grain refinement was noted in a eutectoid composition steel. A sub-micron ferrite structure was observed following high strains (E-3.33) and the mechanical properties exhibit a marked increase in tensile strength.

Jan 1, 2004

By Audrey Wagenaar

Introduction ?? Rising public pressures are being placed on companies worldwide to protect the environment and the health and safety of their workers and local communities. ?? International bodies and shareholders want to make sure developments and companies can meet internationally acceptable standards for EHS. In 2005, Golder Associates was asked by the IFC to conduct a comprehensive review and update for their Environmental Health & Safety Guidelines including the mining sector.

May 1, 2008

AGENDA ? Company Overview ? Industry Direction ? Technology to support maintenance ? data access, connectivity, process historian, downtime & production reporting. ? Case Studies Company Overview Corporate Offices Client Base ?16 consecutive years of growth & profitability ?#39 of Top 50 Control Companies (Worldwide) ?470 employees ?TSX: MTK Industry Direction Improved visibility into the business so they can: ? Reduce cost through better understanding of where costs are being incurred and making timely decisions. ? Optimize operations while leveraging existing assets. ? Have a single version of the ?truth? ? Deliver reliably to stakeholders on the demand for increased accountability (safety, environmental, regulatory performance etc?). ? Respond quicker to market conditions in order to out perform the competition ? Best in Class approach. Web is becoming the standard user interface.

Apr 1, 2005

By William H. Pomroy, Kenneth E. Hjelmstad

An underground mine fire can seriously threaten the lives of all personnel in the mine. This fact makes fire emergency planning a high priority in the mining industry. A fire emergency plan includes a means of warning miners of the existence of a fire, and the need to evacuate or retreat to a place of refuge. The warning alarm must be fast and must reach all miners, regardless of their location or work activity. Means of fire warning are varied, and include such methods as stench, flashing lights, telephones, and word-of-mouth (messengers). Unfortunately, none of these methods are entirely satisfactory. Stench can be slow and seldom achieves total mine coverage, especially in high-back room-and-pillar mines with low ventilation velocity. Telephones are effective only where personnel are close enough to hear the phone ring. A novel fire warning alarm system has been developed by the U.S. Bureau of Mines which enables instantaneous warning of all underground personnel. The warning alarm is sent by an electromagnetic signal which penetrates through mine rock from a transmitter to small person-wearable receivers. Each miner's cap lamp battery could be equipped with a small receiver and when a fire or other emergency occurs the miner could be alerted to the danger by a blinking of the cap lamp. Testing of prototype equipment has demonstrated that the transmitted signal is capable of penetrating through over a mile of mine rock and activating the receiver. This paper describes the theoretical basis for through-the-rock ultra-low frequency electromagnetic transmission, design of the prototype transmitter and receiver, test results, and status of commercial development of systems utilizing this technology.

Jan 1, 1994

"This paper discusses the use of risk assessment and risk management techniques within the Australian underground coal mining industry, within the context of geotechnical risk. The industry works within a pro-active, “enabling” legislative framework, where companies and management apply a range of risk assessment tools as part of their everyday management processes. Different geotechnical risk factors and approaches are reviewed, together with application examples – ranging from mine planning and design, operations, and accident investigations.A particularly powerful resource in each of the above stages of geotechnical management is the RISKGATE system. RISKGATE is an assembled “body of knowledge” structured under different topics across the Australian coal industry, of which three topic areas address rock mechanics issues for both the underground and surface mining sector. This paper will provide an overview of RISKGATE in the context of risk-based rock mechanics applications in underground coal mining."

Jan 1, 2015

By Navid Bahrani

Introduction ? Today?s economic market is motivating underground mining companies to increase development advance rates and enhance their NPVs. ? For example, block cave mining involves development of kilometers of drifts with multiple pillars. ? The cyclic nature of drill and blast, and its inherent tendency to damage the surrounding excavation rock mass and increase support demand often result in poor advance rates ? This has motivated mining companies to replace the conventional drill-and-blast as the main excavation method with alternative methods such as mechanized excavation. ? There is little experience with mechanized or non-explosive excavation methods in hard rock metalliferous underground mining.

Oct 1, 2010

By I. A. Cameron, F. Ham, R. Sriram

"Planned increases in electric furnace productivity and higher matte temperatures needed for the Sudbury Smelter's S02 Abatement Plan, require an improved matte tap hole. Since startup in 1978, the matte tap holes have been incrementally improved by the addition of copper cooling blocks around the refractory tap blocks. These improvements provided a tap block life of about 100 taps per campaign.In July 1993, a prototype matte taphole was installed in Number 2 Electric Furnace to develop the technology to increase tap hole service life. The design was based on a heat transfer model of the tapping process to determine candidate refractory materials and cooler arrangements. The prototype tap hole features increased copper cooling, high conductivity refractories and extensive instrumentation. Eight trial campaigns are reviewed outlining the performance of silicon carbide and graphite refractories and typical heat loads during tapping.IntroductionFalconbridge Limited operates two 36 MYA, 6 electrode submerged arc electric furnaces in Falconbridge, Ontario. The furnaces, commissioned in 1978, smelt a partially roasted nickel-copper calcine, to produce matte for converting and slag for discard. Additional details of the smelter are available in the literature(1-4).Each furnace was equipped with two matte tap holes located in the furnace end wall. Early in the campaign, matte tap holes were identified as a weak area in the furnace which could be improved. From 1981 to 1987, incremental improvements were made to the design by the addition of water cooled copper blocks. In 1993, a prototype matte tap hole was designed and installed in Number 2 electric furnace to develop the technology to increase tap hole service life. Improved service life is required to meet planned increases in electric fWl1ace productivity and the higher matte temperature needed for the smelter's S02 Abatement Plan.This paper reviews matte tap hole development since 1978; outlines the prototype matte tap hole design, refractory selection and installation; and details the performance of the prototype tap hole during the first eight campaigns."

Jan 1, 1995

By L. Sun

A numerical model has been developed to study the air flow in the flow plate and gas diffusion layer assembly on the cathode side of a PEM fuel cell. The flow plate in this type of fuel cell often has serpentine channels and the porous layer is adjacent to the flow plate to diffuse the air to the catalyst layer. Flow cross-over of air through the porous diffusion layer from one part of the channel to another can occur. This flow cross¬over is a result of the pressure differences between different parts of the channel, and it causes the flow rate through the channel to vary with the distance along the channel. A numerical study of pressure distribution and flow cross-over through the gas diffusion layer (GDL) in PEMFC flow field using a serpentine channel system has therefore been undertaken to compare the cases of a single channel and two parallel channels, with the channels having a trapezoidal cross-sectional shape. The purpose of the present work was to study the effect of the flow plate geometry on the basic fluid flow through the plate. The flow here has been assumed to be three-dimensional, steady, incompressible, isothermal and single-phase. The flow through the porous diffusion layer has been described using the Darcy model. The dimensionless governing equations have been solved by using the commercial CFD solver, FIDAP. From the results obtained, it can be found that the single channel systems have greater maximum flow rate difference than the parallel channel systems under the conditions considered in the present study. Also, the size ratio R of trapezoidal cross-sectional shape has a significant effect on the flow cross-over and pressure variation in the flow field.

Jan 1, 2005

By J. B. Mitchell

Using digital image correlation the evolution of strain and strain at the onset of localisation resulting in a hot tear has been determined for alloys AA6111 and Al¬0.5wt% Cu during solidification. High resolution images of hot tear formation and growth were captured during a constrained bar test that incorporated a glass window above a central hot spot region. The images were analysed using digital image correlation software to measure the evolution of displacement and strain based on tracking the motion of discrete features on the as-cast surface of the sample. Temperature data was also acquired with a thermocouple cast into the sample in close proximity to the hot tear. The interval starting from the point immediately after solidification shrinkage ends (the metal pulls away from the glass) and finishing when the first sign of a crack or hot tear is visible to the eye was used to determine strain data. The minimum strain at which strain localisation occurs was found to be 0.0069 in AA6111 and 0.0021 for A1-0.5%Cu.

Jan 1, 2007

By Randy Billing, J. Fraser Wilson

"IntroductionThe job of designing and implementing effective environmental management sounds like what one executive, assuming responsibility for a very sick organization with lots of potential described as, ""an insurmountable opportunity"".Effective environmental management is an opportunity, no doubt. Its an unusual, if not unique opportunity. Insurmountable? Maybe not! Indeed, in the authors' experience, the keys to unlocking this opportunity are not in new or complicated technicalities; they are in the existing strengths and successful experience that one has in managing other complex and exacting management issues.To begin, it is necessary to understand what these issues of sustainable development mean to business. What is the nature of this opportunity? What makes it look unsurmountable?New Games: New RulesLawyers have described some of the new rules companies are facing and there is a new game being played; a game characterized by unique challenges.Take two, for example: • The ecological problems to be faced are Mother Nature's business, the political solutions required are our business. This combination of natural problems and political solutions requires the development of new management mechanisms, to bridge the gaps among us, as individuals, as professions, as interest groups and so on; indeed, even as countries;• and gaps there are : about as many gaps as the people involved : many of them with new and changing expectations, often mutually exclusive and not negotiable.The challenge of these relationships and communications among so many different interests is one of the keys to effective environmental management.Like any game, this one has rules and they are new, too. These rules are evident not just in new legislation - tough legislation with draconian penalties; they are also evident in new and exacting business policies, value driven and just as unforgiving of poor performance. Senior management of many companies are speaking about the role of enlightened corporate policies and how important it is for everyone involved that these policies drive and reflect business practices. Absence of day to- day behaviour which evidences the words in action, the policy on the wall of a corporate office or published in an Annual Report is first evidence for the prosecution , not the defence.The challenge of practical policies is another key to effective environmental management.This is a new game, with new rules: the challenge of change."

Jan 1, 1991

By Dwayne D. Tannant

The Fox Pit at EKATI Diamond Mine reached a depth of approximately 150 m as of September 2005. The pit is designed with 11 m wide benches excavated using a double benching technique leaving 30 m high bench faces. A series of blasting tests were conducted to improve catch bench reliability and increase the percentage of benches that meet an 11 m catch width. The design changes focussed on reducing damage to the bench crest because maintaining the bench crests is the most important factor in achieving good bench reliability. The most significant improvement was obtained by raising the bottoms of the lower trim blastholes by 0.5 m. This change decreases the depth of broken rock below the final bench elevation, and consequently reduces damage to rock that forms the bench crest below. Another improvement was the use of smaller diameter (165 mm vs. 270 mm) blastholes in the A and B rows for the upper trim blast. This change reduces the charge per delay during detonation, reduces the powder factor slightly, and reduces the energy affecting the final pit wall and crest. As mining and the blast testing progressed, the portion of the bench with crest achievements (>11 m) increased from 57% to 75%.

May 1, 2006

By Frank Martonhegyi

"The objective of this paper is to review the coal basins in the Canadian part of the Western Cordillera to aid their understanding, and to aid in finding and proving places of economic coal mining potential. Coal occurs in eugeosynclinal basins in the Western Cordillera which evolved through three stages: -from systems of volcanic arcs in the Late Jurassic to mid-Cretaceous; -through an intermediate stage with deposition in increasingly restricted successor basins in Jurassic to Early Tertiary; -to a continental stage by the Eocene. Minor coal seams occur usually in late volcanic arc stage sediments bur they can be locally thick as they are on Queen Charlotte Islands. Successor basins usually show a marine-paralic-limnic evolurion. Signijicanr coal deposits occur in the tarter two sequences in the Whirehorse (Tantalus) and Bowser (SkeenaSusrur) basins. Currenr activities are intensive in the more accessible Bowser Basin, for example at Telkwa, Susrut River and on the Groundhog coal field. On Vancouver Island major coal seams occur in cyclic sediments, but the more accessible deposits are mined our. Exploration renewed recently in the less accessible northern part of the Island, for example Quinsam, for surface mineable coal. The Western Cordillera is a mosaic of allochtonous tectonic blocks. They originated from the south and were displaced northward by several hundred kilometres. Many Tertiary coal basins are related to strikeslip transcurrent faults along which the later part of displacement took place, for example the Dawson coal area in the Tintina Trench. Tensional and dipslip normal faulting also created or enhanced sites for thick peat accumulation. For example at Hat Creek 280 m of coal occur in a 550 m section. Secondary structures are often better exploration targets than the main fault zones. Pluvial and alluvial fan environments away from the main drainage are usually the favourable sites for thicker and cleaner coal deposition."

Jan 1, 1985

By D. C. Reid

This paper describes the latest results in research and development currently being undertaken by the CSIRO Mining Technology Group to advance the automation capability of continuous mining equipment in underground coal mining operations. This research delivers enabling technologies that are essential in achieving increased roadway development rates as well as providing a safer working environment for underground mine personnel. Details are presented on technical developments and results of large-scale above-ground experiments conducted under field-realistic conditions. These experiments demonstrate the performance of the ?self-steering? capability which will enable a continuous miner (CM) to automatically maintain a given mining heading and mining horizon under production conditions. A primary technical requirement of this automated functionality is the means to accurately determine both the location and orientation of the CM in real-time. Test results of a high performance navigation system utilising vehicle motion aiding technologies are presented. This system combines high performance inertial sensors, and custom-developed radar to achieve a navigation-grade guidance system. Comprehensive performance evaluation has been conducted using a scale skid-steer mobility platform operating autonomously through a typical roadway development mining pattern with a total path length of 2700 m and mission duration of 112 min. Results from this evaluation demonstrate that the sustained accuracy of the navigation system exceeds the original project expectations and is well suited to the requirements for this underground mining application. There are presently no known alternative methods for providing a practical and accurate three-dimensional guidance solution in this application. This achievement represents a significant milestone in delivering a step change improvement in underground coal mining roadway development.

Aug 1, 2013

By L. D. Smith

"The economic evaluation of a mineral project requires a great deal of diverse information to be brought together in one place. The greatest concern is that there will be an error by omission, so it is useful to have a detailed list of what one needs to know in order to make a thorough evaluation. The list that is presented below is intended to act as a checklist for the person who develops and reviews an evaluation, and as a shopping list for the persons gathering data at the project site.There are varying degrees of detail required at the different stages of evaluation in a project, from the ""quick and dirty"" overview, to the pre-feasibility study, to a full detailed feasibility study, to a due diligence review. This list addresses most of the economic variables in a project and can be used for all levels of studies. Its purpose is to identify a variable or issue and to raise a question, which the reviewer can then pursue in more detail using increasingly more comprehensive checklists for each topic. While developed from the point of view of a new project, this list is equally valid for an ongoing operation."

Jan 1, 1994

By H. J. Ni, M. Y. Huang, S. W. Chen

The effects of several fluxes on purification, microstructures and properties of A00 aluminium have been studied. The experimental results and analyses indicate that many cracks and large porosities exist in the surface film above the melt purified by C2Cl6 and that the film is floe and mostly composed of AhO3 and pure aluminum, which carries many carbon particles and AlCh not fully volatilized. And then over 50% of the all-melting residue is pure aluminum, which is one of the major reasons for high melting loss. Moreover, because of a mass of gas bubbles and a state of seethe, there exist many inclusions which size is under l0µm in the microstructure of A00 aluminum purified with C2Cl6 or fluxes containing C2Cl6- With this purifying method, the aluminum crystal grains are extended along the radius that was observed firstly and the average crystal size of A00 aluminum are about 100µm~150µm. In addition, small size inclusions have little affected on tensile strength and micro inclusions under l0µm have little affected on elongation.

Jan 1, 2006

By D. Cruden

DISCODAT is a system of computer programs written for CANMET, Canadian Department of Energy, Mines and resources, to be used in analyzing geological data for rock slope design. The programs were written in Fortran IV for an IBM 360/67 computer. A program conditions field data from field forms for storage in a line file. Data may be selectively retrieved from the line file by a general retrieval program which uses a variety of relational operators. The retrieved data may be displayed as structural diagrams or histograms produced on a line printer or in a number of maps produced on a drum plotter. There is a logical sequence which leads to the characterization of those elements of the subfabrics of a rock mass which may be kinematically active. Structural domains within the rock mass can also be outlined by a procedure described as areal analysis. Costs for a complete analysis are usually substantially less than $l/discontinuity.

Jan 1, 1978

An optimized long-term mine planning determines the best order of material extraction, so that the Net Present Value (NPV) becomes maximum. In the case of oil sands surface mining, one of the key constraints in NPV maximization is the volume of tailings slurry that will be generated downstream. Specifications of tailings slurry are also important from environmental perspective. Moreover, most of the material that will be used for the reclamation of tailings ponds in later periods is generated in extraction and processing of oil sands. In this paper, an integrated optimization framework is proposed to maximize the NPV of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. The proposed model is coded in Matlab and has been run using CPLEX for verification. The results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Aug 1, 2013