Search Documents

By M. U. Oko

"Monitoring of all the waste streams from Falconbridge's Sudbury Operations to determine whether they meet the required standards, has been performed for many years. By 1969, however, the number of samples being collected had become so large that a complete revision of the existing systemwas necessary. Sites previously designated by name only, were numbered, clearly marked on the ground and on maps which were circulated to all concerned. The types of pollutants analyzed were determined and specified for each sampling location and a chemical analysis report form was designed. The sampling schedule has been computerized to produce a periodic listing of the samples to be taken and the analyses required.An area map showing sampling sites, chemical analysis report form, spill report and a computer print-out example are shown and explained.EVOLUTION OF FALCONBRIDGE'S WASTEWATER. MANAGMENT SYSTEMFalconbridge Nickel Mines employs some 4500 people, operates nine mines, four mills and a smelter in the Sudbury basin. The operations are geographically fragmented into four widely separated locations, the Falconbridge operations east of Sudbury and the Onaping operations in Levack Township being the two largest of the four. The Lockerby area located to the west and the Lindsley Mine just north of Sudbury are now under development. The magnitude, the diversity and nature of the operations are such that constant vigilance is needed to prevent inadvertent damage to the environment. The purpose of this paper is to describe the information system used to monitor and control waste-water disposal on Falconbridge's properties to help ensure the maintenance of effluent standards satisfactory to the Ontario Water Resources Commission (OWRC) and to the Ontario Department of Health."

Jan 1, 1971

Superconductivity, New Mexico and Mining? ? High Temperature Superconducting cables made from ?nickel tape? ? Testing on U.S. power grid ? 25 year time horizon Purpose Create awareness about the successful application of energy management systems at a Northern Ontario mine site.

May 1, 2008

By R. Noriega, M. Suazo, V. Murariu

Current AG and SAG mill circuits have continued the trend to larger, fewer mills. These large mills place a significant additional load on the discharge systems and it has become imperative that the designs of these mill discharge systems are evaluated carefully to ensure maximum efficiency and have the capacity to be able to handle the increased mill discharge volumes. The current generation of multiphysics modeling tools allow a detailed analysis of AG and SAG mill discharge performance. The combination of Discrete Element Method modeling and Computational Fluid Dynamics allows the designer to model in detail all aspects of a mill discharge performance. This includes a detailed description of the build-up of solids and slurry in a mill discharge, the recycle of material back into the mill through the grates, the relative wear rates and the occurrence of overloading at the pinch points. These tools allow intelligent decisions to be made regarding the type of discharge arrangement, pan lifter geometry, and discharge cone design, so as to ensure that the discharge is capable of handling the duties required for a specific installation. This paper details the current state of the art in these modeling tools, and provides an overview of some recent applications.

Jan 1, 2012

By Robert B. Parsons

"It is generally acknowledged that Canadian and foreign-based mining companies are spending relatively fewer dollars in Canada and more dollars abroad than was the case not many years ago. It is common to see the Canadian tax system being fingered as one of the causes in this shift in direction. However, if one takes the time to peel away the surface of our tax system, and to probe a little deeper into its substance, it will be found that the Canadian taxation of mining is generally quite competitive. IntroductionCross-border shopping in the mining industry? - Absolutely! Economics 100 teaches that dollars are votes in the capitalist system, and mining companies are going to cast their limited number of votes where they can achieve the highest return at the least risk. The Canadian consumer knows that taxes are a major factor in cross-border shopping, and mining company executives know that the same tenet holds true in their industry. Unfortunately, mining operations are subject to such a bewildering array of tax rules that making an intelligent decision is not always an easy matter.Statutory Tax RatesConsider, for example, the ""statutory"" tax rates shown in Table 1. (Statutory tax rate in this table refers to the simple sum of federal and provincial tax rates on profits as specified in the tax legislation.) Looking only at the total statutory tax rates (such as 66070 for Manitoba) , one might quickly observe that the Canadian mining industry is subject to a truly onerous tax regime, especially as compared to the United States where statutory tax rates can be in the 34% range."

Jan 1, 1992

By R. Phillips, A. G. Doll, D. J. Barratt

"The Bond low energy impact (crushing) work index test is specified to be performed on rock specimens between 50 mm and 75 mm in effective diameter. NQ-diameter drill core, frequently used in mineral exploration programs does not meet that specification, it being 45 mm diameter or less.This paper reports the effect of performing the impact test on contiguous sections of HQ diameter and NQ diameter core, exploring the hypothesis that the contiguous intervals give equivalent results in spite of the core diameter difference."

Jan 1, 2012

The original JKMRC AG/SAG mill model was developed over 30 years ago and has been upgraded a number of times since then, with the current published version being the Variable Rates model that is now over 15 years old. Since this model was developed further enhancements have been derived, some of which are applied in-house and some which have yet to be incorporated. The published and the commercially available model in JKSimMet is currently undergoing a comprehensive overhaul with a vastly extended data base for model evolution and validation. Improvements developed within the AMIRA P9 project, in-house development and a number of collaborative projects, are being incorporated into the upgraded model structure. Enhanced capabilities will include: power-based breakage rates scaling; a far wider mill filling range (from 10% to 40%) that exhibits peak in throughput as mill filling increases; higher ball loads; improved pebble discharge function; improved slurry discharge function incorporating important mill design and operational influences; and the new size dependent breakage function. The model will also be able to accommodate some influence of liner design and multi-component ores (blends of hard and soft components). This upgrade is still a work in progress but substantial changes have been made to date. This paper presents some of the new improvements and their influence on the predictive capability of the model.

Jan 1, 2012

By B. A. Kjarsgaard, C. J. Mwenifumbo

"Abstract - Natural gamma-ray measurements were made in the GSC Smeaton drillhole as part of the borehole geophysical classification of kimberlite pipe 169. In addition, forty samples of Cretaceous sediments (shales, siltstones, and sandstones) and thirty-five kimberlite samples, selected from the drill core, were analyzed for major and trace elements. These elements included potassium (K), uranium (U), and thorium (Th), which are the main naturally-occurring radioactive elements.Different phases of the kimberlite, and the Cretaceous sediments which show variations in the gamma-ray activity, can be easily delineated on the gamma-ray logs. The gamma-ray logs indicate that the radioactivity in the kimberlite derives mainly from Th, and, to a lesser extent, U. Most of the kimberlite units are enriched in Th and U relative to the Cretaceous sediments, and these radioelements are mainly hosted by accessory apatite and perovskite, and minor zircon. Potassium concentrations are low in the kimberlite. The higher K concentration in the sediments clearly distinguishes the Cretaceous sediments from the kimberlite.The U/K and Th/K ratios show important and distinct differences between the two major types of volcaniclastic kimberlite. Kimberlite lapillistones have higher U/K and Th/K ratios than the olivine crystal tuffs. Furthermore, standardized U/K and Th/K geophysical logs can be used to separate marine reworked olivine shoreface sands from other shallow marine sediments that contain kimberlitic detritus. The identification of different phases and/or stratigraphic facies of kimberlite on the basis of radioelement distributions means that gamma-ray spectrometry can assist exploration, particularly in regard to diamond grade distribution."

Jan 1, 1999

By M. Labrie, H. L. Gibson, G. Doiron, J. J. Watkins, D. H. Watkinson

The Corbet deposit is one of 17 proximal Cu-Zn massive sulfide deposits located. within the Noranda Cauldron which occurs within the core of the Noranda Volcanic Complex. The deposit is located at the top of the Havrian Formation, the lowermost formation of the 3000 m thick Mine Sequence; the deposit has Yielded 2.75 M tonnes of ore grading 3% Cu, 0.96% Zn, 2.06 g/t Ag and 1.0 g/t Au. The multi-lens Corbet deposit formed within a 250 m wide crater that occurs within a localized breccia pile. The Corbet breccia pile was constructed by explosive magmatic and hydrovolcanic eruptions localized along the south flank of a larger andesitic shield volcano that formed during the waning stages of Havrian volcanism. The breccia footwall of the deposit allowed unfocused and widespread hydrothermal discharge that resulted in the development of a large area of chlorite and fringing sericite alteration that exceeds, by six times, the size of the sulfide lenses and represents a significant exploration target.

Jan 1, 1993

By Nickvinder Bhath, Johnson Matthey Plc, Jamie Baker, Daniel Kim, Jeff Lucht, Shijie Wang

"Precious metals (PM) in copper anode slimes are traditionally recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of precious metals, including relatively inert metals such as gold and platinum group metals (PGMs). In this paper, a new method to recover PGM from complex and difficult feed streams is described. Using a proprietary Advanced Ion Exchange (AIX) adsorbent which has a high selectivity for PGMs over other metals and can achieve high PGM mass loadings with a series of incredible pilot test data plus the business case generated from the study results are also presented in the paper.INTRODUCTIONPrecious metals in copper anode slimes are traditional recovered by pyrometallurgical processes. Due to the compliance with increasingly stringent environmental regulations, it has made hydrometallurgical processing an attractive method for recovery of many metals, including relatively inert metals such as gold and platinum group metals (PGMs). Fully hydrometallurgical processes for extraction and recovery of gold and silver from copper anode slimes were employed in major copper refineries since 1995, which was first developed at Rio Tinto Kennecott Utah Copper.In Rio Tinto KUC process, the wet chlorination and gold solvent extraction were utilized to enable recovery of gold and silver as well as other metal compounds. The availability of water and the interaction and amenability of gold processing in water-based solution makes it possible that gold and silver are produced in only five days, compared with a traditional pyrometallurgical process that took 45 days. Most copper refineries are still following the tradition, but the use of hydrometallurgical technologies is increasing as the world demand for metals increases, energy utilization, and environmental viability."

Jan 1, 2016

By R. Spring

"Soft-sensors are a computer software alternative to inadequate hardware instrumentation. Filters are averaging methods that reduce the noise in any sensor's signal. This paper introduces these topics and places them in a mineral processing context using then-product formula.Soft SensorsAs their name implies, ""soft-sensors"" are computer programs that estimate values for process variables (Tham, 1991). This approach is useful when the appropriate hardware sensor does not exist, is deficient, supplies only infrequent values, etc. For example, in mineral concentrators the traditional magnetic flowmeter/ nuclear density gauge instrumentation for measuring slurry flows costs $5,000 or more per flow and requires frequent maintenance. However, metal assays are commonly available from online X-ray fluorescence analyzers and application of the n-product formula (Taggart, 1945) to these assays conveniently provides software estimates of the flowrates (albeit only when the circuit is in steady-state).Soft-sensors are used by inferential controllers that base their control actions on the process values ""inferred"" by the soft-sensor. Such was the case at Brenda Mines where the rod mill feed tonnage controller used an inferred value of the cyclone overflow particle size (Bradburn, 1976). It was also the case at Brunswick Mining where reagent controllers adjusted reagent addition rates throughout the plant according to the various ore flowrates inferred by an expert system (Spring, 1991). A unique feature of the expert system soft-sensor was its dynamic flow models which compensated for residence times, material transport lags, etc. Thus the soft-sensor values were valid under both steady-state and nonsteady- state conditions."

Jan 1, 1992

By Bo-Hyun Kim

Outline ? Strainburst criteria and hypotheses adapted for this study. ? Influence of excavation method on rock mass properties. ? Excavation disturbance factors vs. deformation modulus, etc. ? Estimation of blasting damage zone around excavation. ? Considerations of energy on burst-prone ground. ? Literature review & closed form solution. ? Numerical simulations. ? Summary and future works.

Oct 1, 2010

By J. Oliveira, A. R. Barnes, R. Pandher

Sub-stoichiometric roasting of arsenic-bearing copper ores is a well established practice. However, ores containing calcium commonly prove challenging where very low arsenic levels are desired, but the reasons for this phenomenon have largely been speculative. In the course of treating arsenicbearing copper ores by partial roasting in fluid bed reactors, XPS encountered one of these Ca-bearing ores which proved a challenge to roast to acceptably low levels of arsenic. Mineralogical examination of the calcines using a combination of XRD (X-ray diffraction), QEMSCAN (Quantitative Evaluation of Materials by Scanning Electron Microscope) and EPMA (Electron Probe Micro-Analysis) helped to identify the arsenic bearing species and assisted in developing a workable theory on the sequence of reactions occurring during the roast. With the assistance of thermo-chemical modelling, this allowed adjustment of the roasting conditions to minimise the amount of arsenic retention in the calcine in spite of the presence of calcium in the ore and advance the roasting program to a commercially acceptable solution.

Jan 1, 2014

By Brian Hart, Stamen Dimov, Aparup Chattopadhyay, Barun K. Gorain

"A novel gold deportment technique has been developed for complex copper-gold and double refractory gold ores using state-of-the-art technology. Characterization of these ores is a challenging task due to low copper and gold grades in ores, presence of both primary and secondary copper sulfide phases and variable proportion of visible and invisible gold in different sulfides and iron oxide phases.Double refractory ores are mainly composed of silicates and carbonates with moderate clay and mica, and minor amounts of sulfides and organic carbonaceous matter. Gold mostly occurs as ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. The dominance of invisible gold and presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in flotation and leach circuits. Characterization of this carbonaceous matter, commonly known as TCM and quantification of gold associated within TCM, along with different sulfide and oxide phases is highly complex and challenging.Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to diagnostic metallurgy using state-of-the-art optical and automated mineralogy techniques, namely, micro-probe, dynamic SIMS and TOF-SIMS analysis for quantification of invisible and visible precious metal content in various species. The relevance of the mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2016

By W. Almdal

"To compete in the ever expanding global market, companies must continuously improve. Benchmarking, a tool that can help determine where the best areas for improvement are, is more than comparing measures, it is comparing how business is carried out and how decisions are made. The key to success is in integrating benchmarking results into the organization, so that those most affected by the results own them and are empowered to use them as a positive change agent. This is a necessary step to achieving substantive change to practices and achieving optimum performance improvement. IntroductionBenchmarking is a powerful tool that can assist in the continuous goal of improvement. Benchmarking is more than comparing productivity rates or unit costs, it is seeking out best practices and assimilating them into a business to provide a positive change agent.Benchmarking is a continuous process - is time consuming, labour intensive, and requires a lot of discipline. There are no easy answers and no easy solutions, just a lot of work. The results, however, are nothing short of spectacular. More and more companies are adopting benchmarking practices because it is a key tool of the learning organization and will become part of the way business is done, part of the way it is managed. Business must change to stay ahead or to get ahead and benchmarking can accelerate the process of business change. Improvements in an organization can happen faster and more effectively with a benchmarking approach."

Jan 1, 1994

By B. J. Cunliffe

"Filter cloth in the mining industry is an ambiguous title asthis suggests filter cloth use from underground ventilation to the refining processes. The time allowed for this paper would be better served in con-centrating on vacuum filters common to all mine mills and to offer some simple guide lines to the mill metallurgists in the choice of filter cloth for this type of filter.The requirement of the filter cloth is to separate solids from liquids under a vacuum head by forming a permeable layer of solids or cake, through which liquids can flow until the panel or disc sector leave the slurry tank and to continue to pass residual moisture from the cake formed during the cake drying cycle, and to discharge the cake on air-blow so that the cycle can be repeated.Whilst the mill metallurgist should not be expected to under¬stand all aspects of filter cloth manufacturer, it is however, advantageous for him to understand a little of the textile language associated with filter cloth for his own protection against ""trial-and-error"" methods, which are both time consuming and costly.If improvements are to be made over existing filter cloth in use an examination of the limiting factors of the cloth used should be made and the major causes for removal determined, e.g. cloth blinding, high moisture in cake, poor cake discharge on air blow, mechanical damage to cloth.As each of the limiting factors mentioned has a bearing on the choice of fibre used, the yarn type and weave of a suitable cloth, an under-standing of these points will assist the mill metallurgist in avoiding repetitive trials offering little degree of success."

Jan 1, 1971

By Paul Johnston

or is it? Mining Automated Loader Technology Application ? Intelligent software mounted in hardware on a remotely controlled scoop. ? Led by INCO, Sudbury, with ? C-CORE, St. John?s ? Automated Mining Systems, Aurora ? Bell Canada, Sudbury ? Laurentian University, Sudbury ? University of Western Ontario, London Completed: March 2000

May 1, 2008

By Rene A. Morin, John K. Kebe

"As explosives become more widely used in urban and other congested areas, governmental regulations pertaining to their use are becoming more pervasive and stringent. This is forcing the blasting industry to review its entire spectrum of operations. Greater attention is now being paid not only to the design and layout of blasts, but also to the monitoring and recording of their after-effects for both legal and business reasons.Current PracticesThe major users of explosives in urban areas are quarry operators and construction companies. A characteristic of both of these industries, at least in recent years, is a relatively low margin of profit. This, coupled with the fact that their use of explosives is relatively intermittent, prevents them from having the kind of professional consulting services that blasting operations really warrant in today's regulatory environment. When such services are obtained, they tend to be directed more at the design and execution of the blast than at the recordkeeping function. The records that are kept tend to be more in the form of a summary of the consultant's design data as opposed to the kind of after-effect detail that is necessary.The more experienced consultants and operators now realize that at least as much attention must be paid to the record-keeping as to the design work. Regulatory bodies at all levels of government are insisting on the availability of such records.Unfortunately, the instrumentation in use today for taking such measurements does not lend itself to the practice of intermittent consulting. Current monitoring and recording instruments are based on so-called analog technology of the type that has traditionally been applied to the monitoring of earthquakes. They require set-up and calibration procedures which must be repeated each time the instrument is moved, or the blasting parameters are changed, as well as complex total analysis of the recorded data. This can lend to confusion and a dilution of responsibility for anything other than the design work and possibly some summary reporting."

Jan 1, 1985

By Yue hua Hu, Wei Sun, Pan Chen, Li Wang, Runqing Liu, Central South University

"The flotation separation of muscovite from quartz was investigated using mixed sodium oleate/dodecylamine (NaOL/DDA) collectors. The flotation experiments were conducted on single minerals and their collecting performances were studied by means of adsorption amounts and molecular dynamics simulation. Flotation results show that muscovite presents good floatability while quartz exhibits poor floatability in alkaline condition. Adsorption amounts show that both NaOL and DDA can absorb onto surfaces of muscovite and quartz in presence of mixed surfactants. Molecular dynamics simulation indicates that DDA plays an important role in the adsorption of mixed surfactants on these two mineral surfaces. The molecules of mixed NaOL/DDA are arranged in a rigid and well-ordered packing on muscovite (001) surface. Only a few DDA adsorb on quartz directly, and rest DDA and NaOL molecule exist near by the quartz surface, forming a hydrophilic cylinder-like structure. This study may provide guidance for the flotation mechanism and application of mixed anionic/cationic collectors.INTRODUCTIONIn the past decades, there has been an ever-increasing demand for muscovite (KAl2(Si3Al)O10(OH)2) because of its potential applications in cosmetics, construction and metallurgy industries (Barlow & Manning, 1999). Besides, muscovite is an important carrier for some rare metals, including vanadium, titanium and lithium (SsuerrN, 1979). Quartz (SiO2) occurs as the main gangue mineral in muscovite ores, which results in a low purity of muscovite and limits its wide applications. Therefore, there is an urgent need for the beneficiation of low grade muscovite ores. Many studies remove quartz by screening and gravity separation in virtue of their differences in shape, hardness and density. However, these methods undergo poor efficiency in case of small particle size (below 50µm) of muscovite and quartz (Liubakka, Sullivan, Lamphere, Corradi, & Dykhuis, 2011; Santos, Franca, & Ogasawara, 2011)."

Jan 1, 2016

By P. Chollet, A Constant

THE RESULTS of a previous investigation ( 1) on the work-softening of some heat-treated steels have led to the conclusion that the occurrence and intensity of the phenomenon is possibly governed by the work-hardening capacity of the material, and the relative amount of retained austenite. The first assumption is compatible with Polakowski's theory (2) that the absence of work-softening, in steels quenched and tempered at relatively low temperatures, may be attributed to the high rate of work-hardening which compensates for, and even out-weighs, the loss of internal energy associated with the simultaneous rearrangement of the original system of internal stresses. Indeed, Polakowski first considered the work-softening as a manifestation of a partial release (by cold-working) of the latent strain energy stored in

Jan 1, 1962

By J .. Carignan, Y. Dembele, J .. Guha, A. Fowler, A. Gobeil

The Barlow Lake stratigraphic section comprises the top of the Gilman Formation, the Blondeau Formation and the three sills of the Cummings Complex. Representative samples were analysed to allow characterization of the chemo-stratigraphic profile and geochemical affinity of the six rock facies found in the section. All the mineralized horizons are associated with sedimentary units. Geochemical signatures associated with the mineralizations are either very weak or very localized and shown by increases in K20 around the mineralizations and Fe203 near them. The mineralizations are stratiform, synvolcanic but resedimented and remobilized by regional metamorphism and possibly by hydrothermal activity initiated by the intrusion of the Cummings Complex. The evolution of the sedimentary basin with the decrease of its depth is confirmed by the chemo-stratigraphic profiles. Stratigraphic position in the section is important in order that the chemo-stratigraphy may serve as a guide for mining exploration in the distal facies of the Blondeau Formation.

Jan 1, 1984