Search Documents

By C. Diaz, S. W. Marcuson, K. I. Burgess

Deep roasting in fluid bed roasters is the first unit operation in Inco&apos;s "roast-reduction smelting" process for the treatment of nickel sulphide concentrates. The roaster product, a low sulphur calcine, is reduction smelted with coke in an electric furnace to yield a sulphur-deficient matte which is then converted to low (<1%) iron matte in Peirce-Smith converters. Due to the deep roasting, a minimal amount of sulphur dioxide is evolved in the smelting and converting stages. Sulphur is eliminated from the concentrate almost exclusively in the roasters in a single, continuous, strong, gas stream suitable for treatment in an acid plant. This paper discusses the commercial scale testing of deep fluid bed roasting of nickel concentrate at Inco&apos;s Thompson Smelter as part of two commercial scale campaigns on roast reduction smelting conducted in 1981-1982. Slurry feeding, practised during the second campaign, permitted excellent control of the air/concentrate ratio in the roaster and, in turn, good control of sulphur elimination (about 80% of input). Smooth autogenous operation with high oxygen efficiencies (about 95%) was promoted by operating at bed temperatures of830°C to 850°C with calcine recycle. High throughputs and the desired metallurgy were achieved. The extensive testwork conducted during the two experimental RRS campaigns demonstrated thot deep fluid bed roasting of nickel concentrate at high oxygen efficiency is a technically viable operation.

Jan 1, 1994

By Gerald Sanders

Presentation Topics ? We?re Going to the Moon Again? ? What is Lunar Mining ? In-Situ Resource Utilization? ? What Are The Challenges to Lunar Mining? ? What is NASA Currently Doing?

May 1, 2009

By Michael S. Moats, Addin Pranowo, Gerardo R. F. Alvear F., Nigel Aslin

The toxicity of arsenic is well known and documented. However, the presence of arsenic in copper electrorefining anodes and electrolyte is critically necessary to produce high quality cathode. Arsenic as well as antimony and bismuth concentrations vary depending on their relative concentration in the anode copper received from the smelter. This paper will discuss the behaviour and benefits of arsenic in copper electrorefining and the detrimental effects of antimony and bismuth on cathode quality and tankhouse performance. This will include the minimization and mitigation of problems associated with arsenic, antimony and bismuth including cathode contamination, floating slimes, scaling and anode passivation.

Jan 1, 2014

By C. R. Kerr

"This paper describes the revisions to the heating and ventilating system at the Frood-Stobie mill, which resulted in substantial savings in energy costs.IntroductionInco Metals Company, a unit of Inco Limited, is involved in the mining and processing of nickel-copper ores. The Ontario Division of Inco Metals consists of 10 operating mines, with 5 mines and open pits on a standby basis, and 10 pro- cessing facilities, located in Sudbury, Port Colborne and Shebandowan. In 1980, the Ontario Division&apos;s energy expenditures amounted to $87,000,000.Due to the accelerating cost of energy, the Division established an Energy Management Program in 1975 to define, evaluate and implement measures to reduce energy cost and consumption per unit of output by 10% by 1980. This falls in line with the goals set by the mining and metallurgical task force on voluntary energy conservation.To effectively implement the program, Plant Committees were established at each plant and mine area, with an energy management coordinator appointed to coordinate the activities. The Plant Committee&apos;s responsibilities include identifying the major areas of energy consumption, isolating areas with large potential losses and determining what action should be taken to improve energy efficiency.Within a five-year period from 1975 to 1980, the Ontario Division has been able to cut its energy consumption by 8.9 trillion BTUs, the equivalent of 1.5 million barrels of oil."

Jan 1, 1981

By K. V. Konigsmann

"Concentrate dewatering operations have a significant influence on the economics of base metal beneficiation. The expenditures f or energy and labour per tonne of product are high. The relatively low efficiencies of standard techniques present inducements for process modifications. Development efforts at several Noranda concentrators led to process changes which improved productivity, namely, agitated pulp storage in large vessels, process automation and pressure filtration.IntroductionA program was initiated in 1968 with the aim of improving utilization of manpower and equipment in dewatering operations. The following considerations motivated us in this effort: Firstly, filters and dryers had traditionally been operated continuously and in step with grinding and flotation circuits. The demand for labour and equipment operating time was fixed and was not determined by the rate of concentrate production.Secondly, dewatering equipment had usually been designed to handle the concentrate tonnages which were produced when mill feed grades were high; therefore the equipment operated at less than capacity when treating ores of average metal content. The first goal was the separation of the flotation process from concentrate dewatering by development of a practical storage system for concentrate pulps . A second objective was the gradual introduction of dependable automatic controls. The steep increase in energy costs after 1973 added urgency to the search for dewatering processes which were highly energy efficient."

Jan 1, 1984

The mixer that is commonly encountered in hydro metallurgical operations consists of a single turbine and tank combination. However, it would be advantageous to examine some common solvent extraction mixing systems in the light of the fundamentals of chemical reactor design. The basic concepts of reactor design are commonly used in the chemical industry, and it should not be too difficult to apply them to solvent extraction. The factors that affect the engineering design of a reactor are: the reacting system; the type of reaction; and the configuration of the reactor. The reaction system in solvent extraction consists of a heterogeneous liquid phase, involving two immiscible liquids. It is essential f or the process that the reactor product can be separated efficiently in the subsequent settler. The type of reaction in solvent extraction system may be quite complex, and the picture is complicated by the presence of competing and side reactions. The reactors themselves have been generally continuous stirred tanks, and the nature of the mixer-settler makes it unlikely that the pumping mixer can be dispensed with. However, it appears that there should be some definite advantages to a system of stirred reactors in series. The kinetic experiments which are carried out should have the definition of optimum reaction conditions as one of their goals. The data obtained from these experiments must also be applicable to the design of reaction equipment. Reactor selection and design is often a unique problem for each chemical process, and does not lend itself to a systematic general approach. However, the application of chemical and physical principles to mixer design in solvent extraction should result in practical, more efficient plants.

Jan 1, 1979

By Scott L. Ewart, William M. Bryden, Donald E. Wakefield

"Osler, Hoskin & Harcourt develops commentaries from time to time on topics of legal interest. These may deal with new legislation, changes or developments in government policy or recent judicial decisions of importance to its clients. The commentaries are, of necessity, general in nature. Because the law which they deal with is often new and untested, it is hard to arrive at precise statements of the way in which the principle s discussed in a commentary might be applied in specific circumstances. When further guidance is needed , consult a solicitor.The purpose of the Bill is to simplify, modernize and standardize the regulation of mineral exploration and development in Ontario. Many of the changes proposed by the Bill are of an administrative nature and move much of the detail with respect to staking, assessment work, prospecting work, surveys, quarry permits and leases contained in the existing Mining Act to the Regulations contemplated under the Bill.The Bill will undergo revision and be re-introduced and therefore it is not the intention of this present article to detail the specific changes contemplated by the Bill; however , its more significant changes are as follows:1. Provision is made for a lifetime prospector&apos;s licence with the elimination of annual renewals;2. Perimeter staking of a block o f claims is permitted to reduce the cost of staking;3. Assessment work requirements are expressed in term s of dollars spent rather than days worked;4. Persons doing exploratory work are required to furnish notice to owners of surface rights of intention to perform assessment work;5. Annual work summaries will be available to the industry to lessen duplication in exploration work;6. The option of continuing assessment work rather than applying for a lease is provided;"

Jan 1, 1984

By J. J. Jonas

The categories of interpass time encountered in hot rolling are characterized. These are shown to fall into three broad categories: short (in rod rolling); intermediate (in strip processing); and long (in plate schedules). The effects of interpass time on recrystallization and carbonitride precipitation are described, and particularly on the interaction between these two mechanisms. The interactions, in turn, determine the final microstructure produced as well as the mechanical properties.

Jan 1, 2005

By R. C. Hartviksen

"The Drumbo Mine is a new gypsum mine located at exit No. 32 of Highway 401 between Woodstock and Kitchener, Ontario. The flat-lying 6-foot (1.8-metre) bed of gypsum is near the base of the Silurian Salina Formation, about 380 feet (116 metres) below surface. The mine is owned and operated by Westroc Industries Limited. A shaft, 12.5 feet (3.81 metres) in diameter, was drilled and then lined with a liner-sinking technique new to this continent. The shaft was completed in the fall of 1977. Gypsum production was started in December 1978, employing a conventional room - and - pillar method of mining.Historical BackgroundA brief mention of gypsum in the Drumbo area is included in a survey of the Ontario gypsum industry by Guillet. This occurrence was discovered in 1958 when National Gypsum conducted some widespread diamond drilling. Western Gypsum Products Limited acquired leases in 1960 and concentrated a drilling program in Blenheim Township near the village of Drumbo; 79 holes were drilled in an area of 1900 acres (770 hectares). Mining rights were then acquired for 170 0acres (690 hectares). A test shaft, 44 inches (1.1 metres) in diameter, was drilled to obtain a 50-ton (45-tonne) bulk sample. This opening will be used as an emergency escape way and for ventilation.Westroc Industries Limited, a wholly owned subsidiary of BPB Industries, has its head office at Mississauga, Ontario and operates gypsum board plants at Mississauga, Vancouver, Calgary, Winnipeg and Montreal. Other gypsum mines are at Windermere, B.C. and Amaranth, Manitoba."

Jan 1, 1983

By D. B. Langford, R. Hart

"This paper presents an overview of the state-of-the-art in industrial and utility power metering and control systems with particular emphasis on Digital Power Meters and Power Demand Controllers.IntroductionModern micro-processor technology, combined with very fast, high accuracy analog to digital converters, is rapidly allowing economical, digital power instrumentation systems to replace the traditional electro-mechanical meters and equipment previously used for instrumentation, control and protection in industrial power systems. Consequently, instrumentation and Supervisory, Control and Data Acquisition (SCADA) systems that were only practical for the very large utility or user are now available to smaller utilities and users. The information available includes sequence of event recording, trend logging, energy management cost allocation and automated load control, among others. The heart of any power monitoring system is the Digital Instrumentation Package (DIP) . These ""DIP&apos;s"" include Digital Power Meters (DPM&apos;s) and Power Demand Controllers (PDC&apos;s) as well as other specialized instrumentation packages such as Mini RTU&apos;s."

Jan 1, 1991

By Mary Kama, Kaul Gena

"Magnetic skarn ore (MSO) is one of the major copper bearing ore extracted by the Ok Tedi Copper Mine in Papua New Guinea. Copper minerals are recovered by flotation while the iron not associated with copper are discarded as tailings. The objective of this investigation was to determine the iron ore reduction kinetics for the Ok Tedi MSO and ascertain if it can be processed to produce sponge iron for a mini steel plant in Papua New Guinea.SEM-EDAX analyses of the Ok Tedi MSO indicated 10.1% C, 30% O, 0.6% Mg, 1.1% Si, 21.1% S, 0.8% Ca and 36.2% Fe. Most of the iron is in sulfide form. Both naturally occurring and roasted sinters of Ok Tedi MSO samples of different particle sizes were reduced by charcoal carbon at three different temperatures and seven different reduction times. Analyses of the reduced products indicated a metallic iron content of more than 65 wt.% on average.Results showed that there was no significant difference in reduction between fluxed and control materials. Only a slight increase in kinetics with reduced particle size, hence the reaction rate constant (K) did not vary much within the temperatures investigated. Reaction kinetics increases with increasing reduction time at 900°C. Therefore, more iron reduction is observed with particles of 106 µm size. In addition, the results also confirmed that the reduction energy used was higher at 800°C and lower at 1,000°C. In summary, iron reduction can be improved but close monitoring of temperature and reduction times are essential to determine the reaction kinetics of the Ok Tedi MSO. INTRODUCTIONMost mines in Papua New Guinea mine large quantities of iron in the form of sulfides, carbonates, oxides and sulfates that are eventually disposed off as tailings. The Ok Tedi magnetic skarn ore (MSO) contains a significant amount of hematite, magnetite, siderite, ilmenite and pyrite that can be a source of iron. The mineralogical compositions of Ok Tedi MSO reveals more iron minerals than copper, yet all iron containing minerals are collected in the tails from the main copper production stream. Therefore, this study is conducted to investigate the possibility of producing direct reduced iron (DRI), or sponge iron, from the MSO. Such sponge iron may serve as the feedstock for electric arc/induction furnace based mini steel plants in Papua New Guinea."

Jan 1, 2016

Situation Brands & Employment Value Propositions of mining sector firms are perceived negatively Competitive labour market is generally not aware of the diversity of mining careers Jobs requiring unique skills & experiences are no filled Traditional means of generating awareness to attract candidates is not aligned with how youth (for example) uses technology throughout the recruitment process Gobal economic downturn

May 1, 2009

By E. Essadiqi, P. Poruks, D. Boyd, D. Emadi, I. Yakubtsov, T. Turi

This paper reviews the results of an extensive study of microstructures and mechanical properties in bainitic linepipe steels. The research was carried out as a collaborative project between Queen&apos;s, Stelco and CANMET. Basic studies of phase transformations and mechanical properties in these steels established important relationships between processing schedule and microstructure evolution, and between final microstructure and mechanical properties. The best combination of strength and toughness properties is obtained with a microstructure comprising a matrix of intragranularly-nucleated bainite (`acicular ferrite - AF&apos;) and small (~ 0.5 µm) dispersed particles of martensite (`M/A&apos;). We describe this as a dual-phase AF+M/A microstructure. An experimental study on 15-mm thick plate determined the window of steel composition and processing parameters which gives the dual phase AF+M/A microstructure. The minimum strength and toughness properties for Grade 621 (X90) linepipe steel can be achieved by either a lean steel composition (0.04C-1.77Mn-0.04Cr¬0.32Mo-0.31Ni-0.29Cu-0.08Nb) with extreme processing parameters, or by a higher alloy composition (0.04C-2.07Mn-0.50Cr-0.51Mo-0.04Nb) with a more industrially realistic processing schedule. It is proposed how this approach could be extended to obtain higher strength linepipe grades.

Jan 1, 2005

By Ö Yilmaz

In this study, the behaviour of rock mass subjected to blasting load is investigated using three dimensional finite difference numerical modelling. In the analyses, Mohr-Coulomb failure criterion has been used for the characterisation of the rock mass strength. Stresses acting on the borehole boundary have been simulated by an exponential function which reaches its maximum within a short time and then falls to zero value in a considerable time period. The strain rate effect on the mechanical properties of rock material has also been taken into account in the analyses. Four different explosive-rock mass combinations have been studied to investigate blast induced damage zone. It has been observed that proposed equation for the dynamic compressive strength of rock material fits very well to general suggestions. Results have shown that blast damage analysis model recommended with this study is successful.

Aug 1, 2013

By Y. Long

The deep-hole surface blasting technique is a prime method of iron ore mining. Blasting fragmentation is one of the important economic indicators that measures the blast method to obtain the iron ore. To improve the efficiency of the blasting method and further reduce the cost of the subsequent processing of iron ore, this paper summarizes measured data gained from a certain amount of blasting test conducted in an iron ore mine in Guangdong province, China. According to the data analysis, there are differences on iron ore blasting fragmentation by different indicators of deep-hole blasting, such as decoupling coefficient of charge, contact state between charge and borehole wall, and change of detonation position in charge. These factors were compared in terms of relevance and impact. Research shows: under certain rock conditions, the decoupling coefficient of the charge has a best range related to blasting fragmentation. Since the detonation position in charge determines the direction of propagation of the explosion stress wave through ore and rock, bottom initiation and mid initiation will help to improve the iron ore blasting fragmentation in joints fractured rock and ore. The research conclusions have important application value for program design of iron ore surface blasting and to guide other types of rock surface blasting.

Aug 1, 2013

By J. A. Eisele, D. L. Pool

"The Bureau of Mines has developed a particle agglomeration technique to improve the flow of leaching solution through heaps of low-grade gold-silver ores which contain clays. Benchscale experiments and industrial practice have shown that the percolation rate of cyanide leaching solution is greatly enhanced by mixing the ore with Portland cement as a binder, moistening the mixture, mechanically tumbling to form agglomerates, and aging before heap building and leaching. A slight modification ofthe technique allows its application to precious-metal-bearing tailings, which cannot normally be treated by heap leaching because they are too fine. IntroductionMany low-grade gold and silver deposits and tailing materials from former mining operations in the western United States are potential sources for precious metals. These sources are too low grade or too small to support the capital cost of a conventional cyanidation plant but have stimulated the development of lowcost procedures, such as extraction of the precious metals by heap leaching with cyanide. The Bureau of Mines has investigated methods to improve the recovery ofgold and silver by heap leaching these low-grade materials.For heap leaching to be successful, the crushed and stacked ore must have good permeability so that uniform distribution of the cyanide leaching solution through the heaps can be achieved. Some of the most difficult gold and silver ores to treat by heap leaching are those containing excessive amounts of clays, or fines generated during crushing. Excessive amounts of slimes, generally minus 50-micrometre or 270-mesh Tyler sieve size particles, in the heap feed will slow the percolation of the leaching solution, cause channelling, or produce dormant or unleached areas within the heap, resulting in long leaching periods and low extractions. In extreme cases, the clays or slimes can seal the heap and cause the leaching solution to run off the sides of the heap rather than through it."

Jan 1, 1987

By Robert B. Parsons

"The mining industry is adjusting its sights to take a shot at the rising level of non-profit taxes which threaten to handicap the industry &apos;s competitive advantage. In the case of this particular expedition, the industry evidentally has a strong ally - the country&apos;s mines ministers. It appears that an initiative is under way to assess the impact of non-profit taxes on mining in Canada as compared to other mining nations.IntroductionSeventy-five years ago, Canadians were unceremoniously introduced to something called income tax. Since then, income tax has been identified as the source of countless evils ranging from the common cold (attributed to stress) to the demise of the economy. Some years later, the provinces jumped on the bandwagon with their own income taxes, and later on with mining taxes. These profit-based taxes had some appeal to elected officials and to a segment of the populace. The onus of the taxes varied directly with the ability to pay (in theory, at least). Previously, the principal sources of government revenues had been property taxes and customs duties, which were viewed as possibly being somewhat regressive in nature.The mining industry has always had concerns about different aspects of income and mining taxes - the tax rate is too high or the depreciation rate is too low, and so on. Recently, though, the industry has turned its sights on the expanding array of taxes which are not based on profit, including payroll taxes, capital taxes, water taxes, sales taxes, fuel taxes, property taxes, environmental levies and user fees. The industry is seriously concerned that the rising level of non-pro fit-based taxes is not only hampering the industry &apos;s ability to reinvest in Canada, but is also placing Canada at a disadvantage in terms of trying to attract new investment capital."

Jan 1, 1992

By D. F. Machuca-Mory

The new algorithm for high-order simulation of ore deposit grades termed HOSIM is based on the concept of spatial cumulants. The algorithm is tested using data from Apensu, a structurally controlled gold deposit in Ghana. The required high-order spatial structures are obtained from a training image or analogue of the deposit. Using the available drillhole data and training image, HOSIM realizations are able to model well the grades and geometry of the large and well sampled mineralized structures. However, under-sampled small structures remain difficult to model. HOSIM offers a promising alternative for the spatial simulation of complex non-Gaussian orebody attributes of interest.

Jan 1, 2011

By F. H. Samuel, J. E. Gruzleski, S. Valtierra, H. W. Doty, N. Andrade

In this work, the age-hardening behavior of cast Al-Si base alloys was investigated. It was found that multiple aging peaks are present in the age-hardening curves of Al-Si-Cu-Mg alloys. TEM observations reveal that the age-hardening behavior is related to the precipitation sequence of the alloy. For the Al-Si-Cu-Mg alloy, the first aging peak is the result from the high-density GP zones, while the subsequent are from metastable phases. The transition from GP zones to metastable phases may be the main reason of the formation of multiple aging peaks.

Jan 1, 2006

By Jean-Luc Beaudoin

"In addition to the actual energy consumed, billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays. The principles of a power factor regulator, the two ways of improving the power factor and methods for calculating the capacitor values required will be described.The rate structure of the utility company is founded on three cornerstones: the energy consumed during a given period of time and two penalties imposed when the power factor is low or the power demand is high. Even though the normal consumption of a customer might be 10 kW, with a peak demand of 20 kW only once a month, the wiring and associated equipment at the input to the customer&apos;s plant will have to accommodate this peak demand. The power company has no means of forecasting these demands and cannot therefore provide the additional equipment necessary. So it exacts a penalty, and the customer must take all possible steps to avoid these peak power demands. This can be accomplished by using an automatic peak load regulator which will selectively disconnect the loads which are not essential in the operation of a plant .The principles of such a controller will be described.Principles of power factor regulatorsThe operating principles of a power factor regulator will now be described. It might be asked why the power factor of an electrical installation in a mine, or a factory, should be corrected at all, but there is a simple answer. In addition to the actual energy consumed, the billing is dependent on the peak load and the power factor. The lower the power factor goes, the higher will be the penalty the consumer pays."

Jan 1, 1982