Search Documents

By Ferrin Prince

New Gold?s New Afton mine is an 11,000 tonne per day block caving mine, located 8 km west of the city of Kamloops, British Columbia. The reserve is estimated at 52.5Mt with grades of 0.65 g/t Au and 0.93% Cu. Block caving requires a considerable amount of infrastructure development before production can begin. Each excavation had its own challenges, often further complicated by interactions with the caving stresses and fault structures. The main areas of interest were: the production crusher complex, the surface to underground infrastructure, and the footprint interaction with the faults. The ore zone at New Afton is bounded by two very weak fault zones, with large fault affected areas and associated splays. The resulting rock mass rating (RMR) is 35-50, with some areas significantly weaker due to clay infill. These conditions created a unique and decidedly difficult environment in which to develop New Afton?s infrastructure. Despite these difficulties, the mine began production on schedule in July 2012. The main production crusher for the mine is a gyratory crusher that allows for direct truck dumping, with a smaller jaw crusher in series to facilitate the initial development and production. The crusher chamber was redesigned several times to minimize the chamber volume, resulting in a 40% decrease in volume without losing functionality. After drilling and geotechnical testing, the location of the crusher was changed to eliminate the threat of fault affected ground in the area; the entire complex moved a short time before mining began on the chamber. The mining techniques used enabled tight control of the crusher pocket excavation, while also allowing for the timely completion of the chamber. The locations of the surface to underground infrastructure were tightly constrained by geology, surface infrastructure, and an existing open pit. The VR5 raise was drilled and abandoned part way through the reaming process when the drill string became stuck in fault gouge material. It was relocated and successfully completed. The VR7 raise hit a region of poor rock strength and deviated more than 11 m. Poor ground conditions caused a 130m section of the raise walls to fail. An innovative rehabilitation program was undertaken to re-establish the raise for ventilation. A surface to underground slick line was also installed to ease the material movement underground. A layout of the Extraction level was changed from herring bone to straight through drawpoints that resulted in a net reduction of 1.3 km of development. The Apex level was added to aid in the breakage over the major apex pillar and allow for geological mapping. A portion of the caving footprint is located within the footwall fault. The low strength, high clay content, and small joint spacing of the material resulted in blast-hole cut-off and drift deformation. Drift rehabilitation was a key factor in the successful development of the cave footprint. Innovative drilling and loading techniques were used to keep the holes open and to impede movement along the joint structures.

Aug 1, 2013

By David L. Anderson

"The government o f Canada has, since 1981, been under intense political pressure to modify its foreign direct investment (FOI) regulatory regime(1). To date the government's response has been limited to administrative and ""cosmetic"" changes: substantive issues have been largely ignored(2). However, as long as the economy continues to flounder , the Foreign Investment Review Agency (FIRA), as it is presently formulated , will continue to be an easy target for government critics . This phenomenon, in conjunction with the virtual certainty of a federal general election within two years, suggests that changes to the FIR Act will be seriously entertained by the present government.Recent events indicate that if change s are made, they will likely entail the adoption of a special-sector approach within the existing framework of a general screening system(3). Since this approach is currently employed in Australia(4), it would seem to be appropriate, from a public policy perspective to study that country's experience in developing and operating such a scheme. In doing so, I shall focus on the mineral sector; the rationale for doing so is as follows. First, this sector served as the focal point of the Australian FOI regulatory debater(5), Second , with the exception of the oil and gas industries, the non-petroleum mineral sector is one of the few areas of the Canadian economy wherein the Trudeau government has adopted an explicit domestic ownership target(6). Third, the non-petroleum mineral sector is, undoubtedly, a prime candidate to be denoted a s a special-sector if such a framework were to be utilized by the Canadian government!"".Although international comparisons are fraught with danger , a Canadian/Australian comparison is particularly appropriate(8). Both countries have reasonably similar economic, political and social structures . Furthermore, as noted above , Australia is the only other western country which employs a general screening mechanism for FOI. In addition, it utilizes a special area approach ; within this scheme, an explicit target of a minimum of 50% Australian ownership of all new resource projects has been formulated and clearly promulgated to all of the relevant interest groups. This policy, broadly defined, has been in place for more than six years and during this time the Australian mineral sector has, by world standards, prospered(9). Hence, the Australian experience in designating the mineral sector as a key area within a general screening system, should be of interest to Canadian policy-makers."

Jan 1, 1984

By A. G. Pronk, D. M. Burton

"A regional till sampling program in the Upsalquitch Forks-Tetagouche Lakes area, centred some 70km west of the city of Bathurst, has proven an effective method for gold exploration in the heavily glaciated interior of northern New Brunswick. Prospecting activities within this area over the past three years, have led to the discovery of several gold occurences associated with quartz-carbonate alteration in a variety of intrusive rock types emplaced along major fault zonesQuaternary mapping shows that the glacial history is complex. However, the displacement of material is uniform in distance and direction, and the till is generally thin (0.5 m to 2.0 m) and locally derived, making the interpretation of till geochemical patterns relatively simple for the explorationist. Previous studies have shown the the fin e-grained gold is best detected in the -250 mesh (-0.063 mm) till fraction (clay plus silt) and that the C-horizon is the preferred medium for analyses.Samples were collected on a 2 km grid and analyzed f or Cu, Pb, Zn, Au, Ag, As, Sb, Mn, Fe, Ni, Co, and Cd. Results indicate that concentrations of 10 to 20 ppb Au can effectively delineate areas of anomalous gold in bedrock associated with fault structures, and that a good potential for discoveries exists to the west of the known occurrences, where up to 678 ppb A u has been detected in tills. IntroductionThis paper reports on the result s of surficial geological investigations conducted over the past two field seasons in north-central New Brunswick. The stud y area is located in the Upsalquitch Forks-Tetagouche Lakes map area s (N.T.S. 21 0 19 and 21 0 (10) 70 km west of the city of Bathurst (Fig. I). The area is situated on the margin of the New Brunswick Highlands and has a maximum elevation of 640 m (for a detailed description of the physiography, see Rampton et al. 1984).Historically, exploration in northern New Brunswick has concentrated on base metals within the Cambro-Ordovician Tetagouche Group, resulting in the discovery of man y significant massive sulphide deposits (Brunswick No.6 and No. 12, Heath Steele, Caribou, Armstrong Brook, Orvan Brook, McMaster, Murray Brook, and Restigouche). Auriferous base metal occurrences along the Rocky Brook-Millstream Fault have also been previously investigated."

Jan 1, 1988

By Eric Toh, Michel David

"Geo-statistics was born from mining problems: grades not being what was expected; more tons of waste than expected; in other words, dilution. Geo-statisticians now claim to have solved many of these problems, but the solutions seem to have a hard time being picked up by practitionners. One of the reasons may be the jargon which geo-statisticians are using. The reason for jargon is that obtaining solutions required a strict formulation in a statistical framework. Practicing mining engineers and geologists are not used to such a framework, and they are not familiar with the jargon. In this paper, the authors re-examine dilution in operating mines and answer two extremely practical problems, using practical language as much as possible. Can dilution be reduced by improving the quality of blast hole samples? How many samples are needed to obtain a good ore-waste discrimination, i.e. to reduce dilution to acceptable levels? Citing real situations, this paper will try to show how fairly simple concepts can be used to answer both problems. It will try to present the solut ions using a minimum of jargon, even if the theoretical solution could be obtained in a few precisely worded paragraphs.The two problems considered are the following: the first one was encountered in the Panguna deposit of Bougainville Copper Limited, P.N .G., but it occurs in every open pit operation where selective mining is required. As the cut-off is lowered, more and more mining occurs in marginal areas. Grade control is mostly based on the grades obtained from blast holes, hence, it is essential that the quality of the blast hole samples be as good as possible in order to reduce dilution, waste being sent to the mill and ore being sent to the waste dump.The second example stemmed from the grade control technique used in many gold open-pit operations in Western Australia: channels are cut on lines 5 m apart and assays are taken every metre. The pattern in the same regardless of rock type, whether one is in the oxidized zone or not. The number of samples to be treated is enormous, hence, the question arises how to find an acceptable sampling grid, and whether changing it can reduce dilution at an acceptable cost.A solution will be given to each problem separately, although in fact it could be seen that the formal framework is the same in both situations."

Jan 1, 1989

By M. R. Swaan, G. J. Stewart

"ABSTRACTThe application of failsafe techniques to ask the ""What if"" questions about any process has been well established in the chemical industry for many years. The unusual number of fatalities that occurred in Ontario during 1986-87, prompted Inco management to look at the Fail Safe techniques as a method of improving safety performance.INTRODUCTIONOne of the major areas at any time for potentially disastrous accidents is the shaft, where all men and materials must travel. In April 1987, Inco's Thompson Mine's first Fail Safe Team was established to look at its shaft operations. The initial group of eight people was made up of hourly equipment operators, mine foremen, engineering, maintenance and the superintendent. This group took the name of Shaft Risk Analysis Team or SRAT.The many tasks or jobs that are performed in a shaft prompted the team to divide the work under six major headings; slinging, moving men, skipping, dewatering, shaft inspections and moving materials. Each of these areas contained many different tasks which are interrelated. The only way to understand this interrelationship was to flow chart the steps that actually occur in getting any job done.The flow charting is done by the foreman and operators using existing standard manuals and their experience of what actually takes place. In many cases, it soon became apparent that they had been ""working around"" many problems created by their standards. Fine tuning of these flow charts takes place at the weekly meetings, where input from all involved leads to a better understanding of the actual job being analyzed and its potential hazards. Two major points need to be emphasized in getting good flow charting at a mine:I. It must never be blame oriented or you will never discover how the jobs are actually done and hence you won't know what to improve.2 . All team members must have equal voting rights in deciding how to put the charts together so that they have ownership of the finished product. It is far too easy to end up with amanagement view of the way it should be. Many different techniques or methods are being employed to improve the tasks and reduce the risks associated with any job once the basic flow chart is established. The ones found to be the most useful are highlighted."

Jan 1, 1989

By Orlando Rojas, Javier Pizarro, Romke Kuyvenhoven, Francisco Soto

"The concept of geometallurgy has been extensively mentioned and used in the mining industry in the past years. However, each mining firm has a different understanding of what geometallurgy means, and its actual value varies significantly from site to site. Even in the case of properly constructed geometallurgical models, it is fairly common to observe a sub-utilization of the model in the actual operation, because of its low production forecasting capability on the short term. This disconnect between the geometallurgical model and operations is typically caused by a lack of tuning between the original model and the actual plant operation. Also, the absence of procedures and other standards for reconciliation, affects the confidence and the predictive quality of the model. The geometallurgical model should consist of three different levels: (I) adequate capture of information, (II) data analysis and modelling, and (III) development of the block model. Once the geometallurgical in-situ model is finalized, a process model should be developed of the plant at industrial scale, in order to scale up the in-situ geometallurgical parameters from their base or standard condition, to the actual operating reality of the plant. Finally, the stage of reconciliation will close this process, assuring that any deviation between the geometallurgical model and the actual plant operation is not due to lack of tuning, but due to operational issues such as unattended maintenance requirements or poor process control in the operation. The methodology as described in this paper has been applied at several large mining sites in Chile. The paper presents the characteristics of the proposed methodology, and quantitatively describes its benefits with examples from actual operations.INTRODUCTIONIt probably is fair to say that geometallurgy became widely used in greenfield projects in the Andes region during the mining boom of the 90’s, when massive orebodies were studied and developed, and upfront metallurgical characterisation proved its use for accurate economic evaluation including estimates of plant throughput, energy consumption, final product quality and overall recovery. A few examples of such greenfield studies for concentrator plants in the 90’s are Minera Los Pelambres (Antofagasta Minerals, Chile), Minera Escondida, Laguna Seca (BHP Billiton, Chile), and Rio Blanco (then Montterrico Metals, Peru). Large size hydrometallurgical operations such as Cerro Colorado, Quebrada Blanca and Lomas Bayas (all in Chile), also recognised early on the importance and value of relating ore mineralogy, geological characterisation and metallurgical behaviour."

Jan 1, 2016

By S. H. Lucas

"This paper describes the development and application of single-stage fluidized bed continuous ion exchange to the following processes: removal of base metals from mine water; cyanide removal from gold mill waste; uranium removal from sulphuric acid leach liquor; and uranium removal from mine water. IntroductionThe recovery of metals by fixed bed ion exchange has been practiced for many years. However, the operation has been semi-continuous and can only treat clarified liquors. Substantial savings could be made if the operation were continuous, thus reducing the resin inventory, and if the costly filtration and clarification steps could be eliminated. Work has been in progress over the past twenty-five years on the recovery of metals from unfiltered ore leach slurries, heap leach liquors and mine drainage waters containing a small amount of suspended solids. In the case of dilute waste solutions, with suspended matter and high flow rates, filtration is usually prohibitively expensive.Continuous ion exchange operation using fluidized beds has made it possible to reduce considerably the resin inventory and to allow the treatment of unclarified liquors and slurries. The subject has been reviewed on several occasions (1. 2. 3, 4). Although fluidized beds in multi-stage columns are an improvement over previous resin-in-pulp treatment, they have complicated internal structure and I or involved automatic control systems to move the resin stages.Slater and Prud'homme performed studies on multi-stage fluid beds, and concluded that the performance of single, deep fluidized beds of resin with continuous or semi-continuous flow of both phases would be worth investigating, particularly in the case of very dilute metal solutionsoi, A pilot plant was designed and built at CANMET in a cooperative project with Dr. Slateroi. The use of deep fluidized beds of resin (with a large height/diameter ratio) for treating dilute solutions has the attraction of engineering simplicity. Extreme simplicity of equipment design is considered of paramount importance when treating, for example, mine waters at high flow rates, possibly of the order of several million gallons per day. This paper describes the development of the concept of single-stage fluidized bed continuous ion exchange arid reviews the pilotplant development of processes for the treatment of base metal mine water, cyanide waste water, uranium leach liquor and uranium mine water."

Jan 1, 1980

By G. W. McDonald

"The mineralogical studies done on Hope Brook ore samples indicated that a heap leach gold recovery process may be possible. In the metallurgicalprogram that followed, column tests confirmed this interpretation. A 9300 tonne demonstration heap leach test, in the late fall of 1985, reaffirmed laboratory results while identifying operating conditions that will have to be addressed in a production heap leach plan. Operating plans, gold recoveries and cost areas will be presented.Another important factor in a successful operation is the environment approach.LocationThe Hope Brook gold deposit is located 5 km inland from Cinq Cerf Bay on the south coast of Newfoundland. Port au x Basques is 80 km west and Burgeo 40 km to the east of Hope Brook. As there are no roads in the area, access to the site is by sea or air (Fig. I). The Hope Brook orebody is near the saddle of three watersheds flowing to Cinq Cerf Brook, Boat Hole Brook and Betty's Pond. Acceptable solutions to several environmental concerns can be obtained by using the relative sensitivities of these watersheds.The terrain at the site is generally rolling to hummocky with numerous small ponds separated with rock outcrops and patches of peat covering. Tree vegetation is sparse except in the sheltered areas around Couteau Bay and Cinq Cerf Brook. GeologyThe Chetwynd deposit is hosted by the Lower to Middle Ordovician Georges Brook Formation of the La Poile Group, a thick sequence of volcanic and sedimentary rocks.The Hope Brook Zone contains the largest concentration of gold found to date at Chetwynd. The zone occurs as an intensely silicified lens 100 m to 550 m long (average 400 m) by up to 60 m in width and forms the eastern portion of a more extensive, 4 km long , alteration zone trending at 053 degrees Az and dipping 70 degrees southeast.The Hope Brook Zone contains massive finely granular quartz, scattered blue quartz eyes, 3070 to 8% pyrite, minor calcopyrite and trace molybdenite. Barren silicification envelopes the gold mineralization. The zone is flanked to the southeast by a 200 metre thick aluminosilicate alteration zone and to the northwest by a 10 metre barren pyritic siliceous fragmental rock . The original lithology may be either a thick felsic pyroclastic sequence or a quartz porphyry sill that has been altered by hydrothermal processes. Silica flooding of the permeable host was accompanied by gold deposition."

Jan 1, 1989

By J. Bigu, M. G. Grenier, S. Hardcastle

"This study was undertaken in a belt conveyor drift of an underground hard rock mine. The conveyor transported ore or waste from a crushing operation located upwind from the drift sampling locations. A 250 m section of this drift was selected and several types of measurements were taken. Average respirable concentrations in the drift were 0.43 mg/m3 and 0.19 mg/m3 for total and silica dust, respectively. From the respirable dust concentration profile along the drift, it may be possible to estimate the contribution from extended sources such as dust produced by the belt and return idlers.The airborne dust in the drift had an average mass-median aerodynamic diameter of 4.2 micron. A continuous dust monitor showed that the crushing operation produced fairly high dust concentrations (sometimes greater than 4 mg/m3) over short periods of time.IntroductionAirborne dust in the respirable range is known to be the cause of various forms of lung ailments . In underground mines, respirable dust sources are created at many stages of production. All mining operators are responsible for de signing and establishing means of reducing airborne dust. In some cases, sources of dust are well defined and suppression methods are standard.In the case of interest here, the airborne dust cloud was formed from the contribution from many sources, which may be either discrete or extended. At the experimental site, the discrete or point sources were the crushing operation and the belt conveyor transfer point (tail pulley). These sources may be controlled by proper dust capture and scrubbing systems as well as dilution ventilation. Examples of extended dust sources in the area include dust produced by the re-entrainment of settled particles along the drift. Ventilation air movement and vehicular traffic both contribute to this phenomenon. Dust produced by the conveyor is another example of an extended dust source. Caked deposits on the return strand and idlers as well as the transportation of dry material on the belt, can be major contributors. Proper wetting of roadways and muck as well as proper belt cleaning techniques can help reduce these emissions. The cleaning apparatus, used on the belt where these experiments were conducted, is shown in Figure I. These and other belt cleaning techniques are described in more detail elsewhere."

Jan 1, 1987

By G. N. Nnadi, R. J. Mitchell

"The response of cemented backfills subjected to simulated blast loadings is studied using centrifugal modelling techniques. Scaling requirements for centrifugal modelling are developed and the results of the similitude analysis show that an acceleration field is required to capture the true dynamic response of backfill models. Experiments have been conducted at various centrifugal accelerations. The effects of ring blasting were simulated by an impact loading on the exposed fill face. The behaviour of the cemented backfill was monitored with accelerometers as well as dynamic stress gauges.Cemented backfill response to impact loadings was found to depend strongly on simulated gravitational stress level. Results also show that the characteristics of the response changes with distance from the impact. Finally, the results of the models were used to predict prototype peak accelerations, velocities and displacements. The results reported in this study indicate that centrifuge modelling may be a useful tool for dynamic studies of blast damage to backfills. Centrifuge modelling can be carried out at low costs and can be used to design prototype instrumentation systems. IntroductionThe response of cemented mine backfills to blast loadings is of concern to the mining industry because these backfills provide local and regional support during ore pillar extraction. Considerable research has been reported on the static stability (Smith et al., 1983) and on effects of reinforcements on cemented backfills (Mitchell, 1989). However, information regarding dynamic aspects of cemented backfill is limited. O'Hearn and Swan (1989) reported on the response of cemented backfill to blast loading, but these blasts were not very dose to the backfill . A schematic representation of a rock-backfill system is shown in Figure I.The mechanics of transfer of explosive energy to rock and subsequently to the backfill, and the resulting responses, are complex. Achison (1968) listed more than twenty factor s affecting the blast fragmentation of rock and grouped these into the categories of explosive parameters, charge parameters and rock parameters. Although significant advances have been made, during the past two decades, in understanding the mechanics of blasting, the degree of uncertainty associated with predicting the behaviour of backfills subjected to dynamic loadings makes the application of simple design safety factors insufficient. Comprehensive testing programs or prototype instrumentation is required to evaluate the risks associated with blast or earthquake loadings on backfill."

Jan 1, 1991

By J. Bensabat, B. Figueiredo, A. Niemi, J. Rutqvist, C. F. Tsang

"A hydro-mechanical model was developed to study the interaction between mechanical deformation and fluid flow in the fault zones during CO2 injection and storage at the Heletz site which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The potential reservoir for CO2 storage at the Heletz site consists of three sand layers separated by lowpermeability shale layers. The potential consequences caused by fault reactivation, focusing on the shortterm integrity of CO2 storage, are evaluated. The difference in the results obtained by considering the three-layer as an equivalent layer storage formation is analyzed.INTRODUCTIONLarge-scale storage of CO2 in deep underground reservoirs may cause considerable pore-pressure perturbation as well as flux migration and concern has been raised over whether shear slip displacements may be induced in nearby faults, as a consequence of their reactivation. A state-of-the-art review can be found in Rutqvist (2012), which describes the various possible effects resulting from CO2 injection into a deep sedimentary basin, including those involved in reservoir stress–strain changes, micro-seismicity, caprock sealing performance, and potential fault reactivation. Moreover, several studies have recently shown how CO2 injection may produce seismic events both on major faults (i.e., large faults with large initial shear offset) (Cappa & Rutqvist, 2011a, b, 2012), and on minor faults that might have gone undetected during the site characterization, e.g., faults less than 1 km long and without detected initial offset (Mazzoldi et al., 2012).The present paper is concerned with the Heletz formation which was chosen as a test site for CO2 injection experiments in the framework of the EU-MUSTANG project. The Heletz site located at the southern Mediterranean coastal plain of Israel and the structure is an anticline fold with a crest of about 4 km by 2 km. The structure is gently dipping to the east, truncated by a pinch-out line to the west and subdivided into a number of blocks by transversal normal faults with small displacements. The water table is located at 300 m below the land surface. An areal sketch of the site with the elevation of the caprock and the location of the borehole that has been chosen for the CO2 injection experiment is presented in Figure 1."

Jan 1, 2015

By Donald Roberts

"Parameters f or design and development of an emergency hoist system (Fig. I) were submitted to Timberland Equipment Limited of Woodstock, Ontario by the Potash Corporation of Saskatchewan Mining Limited.The unit is the first of its kind in Canada. Not only does it comply with the province of Saskatchewan's mining regulations, but has the added advantage of being completely mobile and self-contained.As well as being useful in the mining industry, the mobile hoist unit could be used in other emergency situations such as rescuing people trapped in wells.JustificationRevisions to the Mines Regulations under Section 13 of the Occupational Health and Safety Act, 1977, of the Province of Saskatchewan stipulate as follows:"" Section 410 .04(4) The Mine Employer shall make adequate provision at every mine where any worker is hoisted in a shaft not equipped with a manway to enable an y such worker trapped in a conveyance in the shaft to be rescued . "" It was not possible to equip the shafts at PCS Mining' s Divisions with "" manways"" and therefore an alternative was required.BackgroundThe Potash Corporation of Saskatchewan Mining Limited, a subsidiary of the Potash Corporation of Saskatchewan, operates four potash mines. Of these, three, Cory, Rocanville and Lanigan Divisions are wholly owned while the fourth, Allan Division, is 40% owned by Kidd Creek Mines Ltd., but managed by PCS Mining. The four underground operations all have a service and production shaft.From 1979 to 1981 the PCS Mining Division, along with Central Canada Potash, were developing an idea to use the existing ground-mounted timberland hoist at Lanigan as an emergency hoist. This hoist was used in the past for rope-up work at both Rocanville and Lanigan and other potash mine s. The Department of Labour at this time had concerns about the time it would take to load, t ran sport and re-install the hoist on a foundation when needed for an emergency. Weight and size made this particular unit very cumbersome for transporting.In addition, the speed at which this hoist operates is too slow for rescue work. When the Department of Labour expressed concern that this unit would be unsuitable for these rea sons, a search for a suitable unit was initiated.The project responsibility for procuring an emergency hoist for the Potash Corporation of Saskatchewan Mining Limited was assigned to the author, a shaft/ hoist specialist a t PCS Mining."

Jan 1, 1986

By Mario Giavani

"IntroductionBy the 1980s, the continuous casting process had almost replaced the ingot casting of steel in Japan, Europe and North America. While economic benefits were probably initially the prime motivator, the transition rapidly proved that continuous casting in conjunction with ladle metallurgy offered a much greater degree of process control and made possible routine steel specifications not previously available.This new technology demanded improved procedures for the quantitative addition of the required metallurgical reagents, especially as regards the more volatile or toxic elements such as calcium , boron, carbon, sulphur, lead and tellurium. The injection of a thin steel tube containing the additive into the metal bath of a ladle refining station offers the best procedure for this. In the industry this has been referred to as ""Cored Wire "".Operators using this technology find that they are faced with balancing the injection speed against the small cross section of the tube to feed the required amount of reagent within the short time span available to the operation. Large-ladle shops requiring major quantities usually resort to multiple machines and high speeds. Many machines approach a maximum feed rate of 400 m/min. Higher speeds exceed the melting rate of the system, and the ferro static buoyancy of the tube will cause it to coil up the ladle wall and possibly resurface into the slag layer, and even eject itself above the surface. Under these conditions, exact control of element recovery becomes difficult, especially with the commonest addition, calcium silicon alloy.Many experts are persuaded that the final melting position of the carrier tube has major importance in establishing consistent element yield to the bath.For instance, the vapour pressure of calcium at l500 °C is close to I bar. Reaching a melting depth sufficient to accommodate this value is considered to be critical to achieving an acceptable and reproducible yield.Many studies have elaborated semi-empirical formulae to establish the melt zone depth, connecting this value essentially to the diameter of the tube , the injection rate and the superheat of the steel. The author's experience in steelmaking could not confirm such formulae in many cases, and he set about to develop a mathematical model which would be useful in addressing this problem, taking into account the several parameters which will regulate the behaviour of a filled tube immersed in molten steel."

Jan 1, 1991

By G. R. Haiden, E. Henderson

"An LHD teleoperation and guidance system, developed at the Ontario Division of Inco Limited, has been demonstrated in operation at Copper Cliff North Mine (CCNM) since late September, 1993. The tests performed to date have evaluated the feasibility and production viability of multiple LHD operation, from surface by one operator.The systems technology required to accomplish this consists of an electronic monitoring and control package mounted on the LHD; a high bandwidth mining computer network capable of providing radio frequency coverage; and an operator control console which provides an operator workstation for multiple LHD operation.This paper discusses the systems required to accomplish the task of LHD teleoperation and guidance, the benefits of multiple machine operation and future research and development directions. IntroductionSince underground mining began, persolU1el have entered the mine workings to mine ore. Today, however, the rapid advancement of modem telecommunications, computer hardware and software technology has opened the door to remote mining technology that was considered unfeasible a few years ago. This paper discusses the ingredients of remote mining technology that have been developed at Inco Limited.Figure I represents an historical view of the application of electronics to LHD operation at Inco Limited. In 1980, the first radio remote controls for the operation of LI-IDs in large open stopes were tested. The successful application of this technology at Inco went hand-in-hand with the development and application of the Vertical Crater Retreat mining method. The combination of these two advances had a very positive effect on the productivity in the mid-eighties at Inco. In 1991, the Mines Research Department of the Ontario Division advanced remote control technology by developing a high capacity underground mining telecommunications system. This system is capable of moving voice, data and video information throughout the mine workings. The system is based on broadband communication technology found in most automated factories, with the added benefit of providing the information to and from mobile equipment through radio interfaces. The first test of the system consisted of an operator teleoperating a single LHD (on the 3000 ft level) from the surface. The next test on September 13, 1993, demonstrated the first production application of multiple LHDs being run from surface with a single operator."

Jan 1, 1994

By Robert B. Parsons

"New Brunswick Finance Minister John Baxter pulled something out of a hat for the mining industry in April, but there is a general concensus in the industry that he should put II back where it came from.The industry has never been in the mood f or progressive rate structures, but that is exactly what New Brunswick 's 1984 budget offers to this depressed sector of the economy.IntroductionThe Province of New Brunswick stunned the Canadian mining community in April with the announcement that the province' s 16% mining tax rate would be replaced with a progressive rate structure effective January 1, 1984 (Table I). The proposed change, contained in the bud get papers tabled by Finance Minister John Baxter on April 17, caught the industry totally by surprise. The move to a progressive rate structure was completely unexpected for a variety of reasons:• Generally speaking, relations between the province and the industry have been relatively good, yet the industry was apparently not consulted with respect to the proposed measure and had no indication that a change of th is nature was coming. This is in stark contrast to the mood which prevailed during the major revamping of the province' s mining tax regime in 1977: at that time, the industry was invited to contribute in advance to the province's plan for a new tax structure.• The new structure would appear to make th e province less competitive in terms of mining tax rates with Ontario , Quebec, and other provinces, despite indications in the past that New Brunswick is very cognizant of this competitive factor in formulating mineral policy.• A joint report in November 1978 by federal and provincial officials to federal and provincial finance and resource ministers, which was careful not to directly criticize Ontario and Quebec's progressive mining tax rate structures, recommended that provincial "" tax regimes be examined to ensure the inclusion of appropriate mechanisms to avoid the excessive taxation of cyclical type profit "" , and that ""the federal and provincial governments consider the concern over progressive tax regimes expressed by the industry and examine mining and royalty tax regimes and the income tax regime with a view to alleviating the effect of such regime on the aggregate marginal tax rate"". In this context, any move to a progressive rate structure would be viewed by many observers as retrograde."

Jan 1, 1984

By M. J. Brodie

"The decision to proceed with mine decommissioning, generally involves a number of complex and independent factors. These factors, including potential for re-opening, legal requirements, contingent liability, asset depreciation, due diligence, and public relations are discussed in the context of the financial implications on a net-present- value basis. It is concluded that the decision to delay mine decommissioning is commonly not in the best financial interests of the mine operator. Some measures to reduce decommissioning costs and expedite the process are presented.IntroductionThe primary audience for this paper is mining executives, although it should be of interest to all professionals involved in the planning and carrying out of mine decommissioning. Historically, mines were abandoned, not decommissioned. Then, as decommissioning became required, it was assumed that salvage revenue would pay for decommissioning. During the I980s, it became apparent that mine decommissioning costs would exceed salvage revenue for nearly all sites, and that a substantial net cost for decommissioning would be realized for some sites. Throughout this period, the approach to decommissioning has evolved through the sequential addition of measures to meet the increasing regulatory burden. This has resulted in a process in which the elements of decommissioning may not be optimized with respect to each other for the most favourable net present value to the corporation. Additional considerations which are not specific to mine decommissioning, such as environmental policy, due diligence and public relations, may now come to bear on the decision-making process.This paper addresses the issue of mine decommissioning as a three-step process. The first step involves identification and evaluation of all of the issues that relate to mine closure, the most importantof which is the potential for re-opening of a mine. Assuming that it is decided that a mine is unlikely to re-open, the second step is to determine when to carry out the decommissioning work. This aspect is examined through a net present value (NPV) approach. Finally, details regarding who does the work and how the various tasks are divided up must be resolved.Every mine is a unique concentration of minerals at some specific location, hence the development, operation and closure of a given mine must be regarded as a special case. Superimposed on the site-specific considerations are the size, history and financial status of the associated corporation."

Jan 1, 1995

By J. Brent Hiskey

At present, approximately 80 % of the worlds mine production of copper is achieved by smelting and electrorefining. The principle aim of copper electrorefining is to satisfy the large demand for extremely pure copper. It is remarkable that high quality copper cathodes with the required purity (99.99+% Cu, ASTM B115-10) and structural characteristics (i.e. deposit density and morphological texture) are produced from impure copper anodes dissolved in electrolytes containing a variety of impurities. This is accomplished with the proper control of operating parameters such as: current density; temperature; copper and sulfuric acid concentration; agitation; substrate preparation; and the application of electrolyte additives. The basic elements of the electrolysis of copper have not changed significantly over the past 150 years since the early developments of James Elkington. Importantly, our fundamental understanding of the underlying electrochemistry has advanced considerably. This is especially true regarding our knowledge of the mechanistic role of additives during the electrocrystallization of copper. This is a very complex subject and modern electrochemical techniques and the development of surface characterization and imaging instruments has helped immensely in our ultimate understanding of how additives control the deposit structure and morphology. The purpose of this paper is to review the historical development and application of electrolyte additives in copper electrorefining and to examine our current knowledge regarding their use. INTRODUCTION The first transatlantic telegraph cable was completed in August 1858. Regrettably, this cable failed shortly after the initial connections. After several more failed attempts, improvements in materials and copper quality resulted in successful communication between Europe and America on July 28, 1866. In many ways this hallmark event demonstrated the need for high purity copper. The first copper refinery in the world was commissioned in May 1869 in Pembrey, South Wales by partners Josiah Mason and James Balleney Elkington. (Historical Note). The 1865 and 1868 British patents issued to James Balleney Elkington were the foundation for the first commercial production of high purity electrolytic copper (Elkington, 1865, 1869, 1870). This important achievement was made possible primarily by the invention of the dynamo which was based on the fundamental operating principles advanced by Michael Faraday. A symbiotic relationship between copper refining and the dynamo was henceforth established. The dynamo provided electric current for electrolytic refining of copper and the electrorefining tankhouse provided pure copper which was required for the generation and transmission of electricity.

Jan 1, 2019

By F. Hassani, E. Aflaki, M. Nokken, M. Kermani

"This paper presents and compares the physical properties of Gelfill and cemented hydraulic fill (CHF) obtained by lab experiments. Gelfill consists of tailings, different binders such as Portland cement, fly ash and blast furnace slag and an alkali activator such as sodium silicate. The CHF and Gelfill samples with various mixture designs were cast and cured for 28 days. The influence of sodium silicate concentration, pulp density and mixing time on the mechanical properties of samples were evaluated using the uniaxial strength test. Mercury intrusion porosimetery (MIP) was used to analyse the microstructure of CHF and Gelfill samples.This study concludes that: (i) The mechanical properties of CHF can be improved by the addition of appropriate amount of sodium silicate. (ii) The rate of strength acquisition in Gelfill samples is faster than CHF samples over 28 days of curing period. (iii) Mixing time strongly influences the mechanical properties of Gelfill samples but did not have any effect on CHF samples. (iv) The MIP analyses indicate that the pore size distribution and total porosity of Gelfill and CHF were different, and this did contribute to higher strength development of the Gelfill samples. INTRODUCTIONThe increased depths of mines in the Canadian Shield and the high stress associated with these depths favour a new method of mine backfill that can both meet strength requirements and help mine productivity. The mine backfill mainly consists of tailings, water and binder materials, the latter being most expensive. Gelfill is a new mine backfill material whose binder usually consists of alkali activators such as sodium silicate and other cementitious materials such as blast furnace slag and normal Portland cement. Although sodium silicate has been used in concrete manufacture, the use of this material in mine backfill is relatively new (Doucet, 2007, Razavi, 2007). Until very recently there have been only a few isolated publications, mostly out of McGill University, regarding mine Gelfill (Razavi, 2007 and Kermani et al., 2009 and 2010). These papers have investigated some of the basic mechanical properties and mechanical behaviour of Gelfill. However, the physical performance of Gelfill in various conditions has yet to be understood. Therefore, the main objective of this study was to investigate the influence of mixing time and sodium silicate concentration on the mechanical performance of Gelfill and CHF through a series of experiments. Moreover, the microstructure of the Gelfill and CHF samples was studied."

Jan 1, 2015

By J. X. Guo, A. Pindred, J. Moore

"Two modified centrifugal flotation cells (CFC), Q2 and Q3 models, have been developed for froth flotation. The operating mechanism of Q2 uses a rotating bowl to create a centrifugal force on the feeding slurry. Froth concentrate is collected on the central top of the cell and tailing is discharged along the top edge of the rotating bowl. The Q3 utilizes a vertical rotating feed pipe to introduce the feed slurry into a stationary flotation column cell. A centrifugal force is also created by a rotating pipe for the feeding slurry. Froth concentrate floats over the cell and tailing discharges through the bottom of the cell. The centrifugal force causes the flotation recovery of fine particles from CFC to be higher than from the conventional cell. The major operating variables of CFC are the rotating speed, air flow rate into feed slurry, and slurry feeding rate etc. Flotation tests have been carried out on synthetic mixtures of galena-silica and chalcopyrite-silica, as well as some natural base metal ore samples. Parallel tests were also conducted on a conventional flotation cell. The comparative test results demonstrated that both Q2 and Q3 have the advantage of higher recovery of finer than 10 µm mineral particles, which are very difficult for the conventional non-centrifugal flotation cell to recover. The grade-recovery curves produced from CFC are equivalent to or better than the conventional flotation cell. There is a potential in the future for the CFC to be employed in slime flotation.1. IntroductionA centrifugal flotation cell (CFC) was originally developed by Clean Earth Technologies [I] to separate oil from water and was subsequently applied in froth flotation. Figure 1 illustrates the design of the original CFC, in which a vertical feeding pipe is attached to the center part of a rotating drum and a stationary shell encloses it to direct the float froth and tailing discharge. The slurry flows down to the bottom of the spinning drum, gets in touch with a screen of air bubbles and then migrates outwards under the effect of centrifugal force. After the mineralized froth enters the rotating cell, it is pushed back to the inner surface. The overflowing froth is collected in the froth launder while the tailing slurry is discharged through orifices along the outer rim of the drum."

Jan 1, 1998

By K. E. Harley, M. J. Whiting, T. J. Sabin, E. M. Ryan, J. F. Watts

"Wire and Arc Additive Manufacturing (WAAM) has the potential to enable a very significant reduction in buy-to-fly ratio compared to conventional manufacturing through the ability to build near-net shape components. Components manufactured from AA 2319 by WAAM can exhibit significant levels of porosity. There is also a variation in the physical appearance of the surface deposit sometimes found on such components. This deposit is similar to those observed on aluminium joined by MIG and TIG welding processes. It has been suggested that both the bulk porosity and the surface deposit are caused by hydrocarbon-based lubricant on the feedstock wire. An established correlation between surface deposit and porosity would offer valuable insight into WAAM products and enable early interventions in quality control or process monitoring based on visual examination. The relationship between the nature of the surface deposit and porosity has been studied for AA 2319 WAAM components manufactured using different wire batches. Evidence is presented to support the assertion that (i) there does not appear to be a relationship between surface deposit coverage and porosity, (ii) batch-to-batch variability in feedstock wire affects porosity. This study has led to a better understanding of the cause of porosity in WAAM components.INTRODUCTION There is a high cost associated with conventional, subtractive manufacturing because of the high ‘buy-to-fly’ ratio, a measure of the initial material bought compared to the material found in the finished part (Allen, 2006; Yilmaz & Ulga, 2016). A typical aerospace product may have up to 90% of the purchased billet of forging machined away which is cost inefficient and high in material waste. Wire and Arc Additive Manufacturing (WAAM) has the potential to reduce costs and lead time. Robotically controlled weld torches rapidly deposit feedstock wire in layers to build large near-net shapes with mechanical properties similar to those of conventional manufactured parts (Sequeira Almedia & Williams, 2010; Martina et al., 2012; Ding et al., 2015; Williams et al., 2015). A high level of porosity variation has been observed in aluminium WAAM parts (Cong, Ding & Williams, 2014; Gu et al, 2016) which can result in a range of material properties (Rudy & Rupert, 1970). This leads to difficulties in regards to standardisation and qualification of process and parts. In order for WAAM to be used commercially, porosity will need to be understood, monitored and reduced to a reproducible acceptable level or eliminated."

Jan 1, 2018