Search Documents

By R. P. Viljoen, A. L. Sokolov

"The distribution of mineralized provinces is analyzed on the basis of their genetic link with specific blocks of the earth's crust including ancient platforms, mobile belts and zones of tectonicmagmatic activation. Mobile and fold belts surround the Siberian platform in Russia and the Kaapvaal craton in South Africa, with decreasing age zoning away from ancient platform margins. The main differences in the geological development of the two cratonic areas are: (1) the long period before the final stabilization of the Siberian platform (3600 Ma to 1600 Ma) and the comparatively short period of time for the stabilization of the Kaapvaal craton (3600 Ma to 3050 Ma) and (2) the intensive multiple activation of the marginal zones of the Siberian platform and the tectonicallycontrolled, magmatic sedimentary, intracratonic activity, typical of the Kaapvaal craton. Mineralization of the Siberian platform is largely characterized by marginal reactivation zones of differing ages although mineralized intracratonic Cu-bearing basins of Proterozoic age are also known. Mineralization of the Kaapvaal craton is mainly related to the formation of the intracratonic basins i.e., Witwatersrand (Au, U) and Transvaal (Au). The latter is characterized by multi-age volcanic-intrusive activity including the emplacement of Bushveld Complex (Cu, Ni, Pt, Cr, Au, V). The Siberian platform is characterized by the prolonged development of inherited mineralization from Archean until the late Mesozoic. The main period of mineralization in the Kaapvaal craton is restricted to the middle Proterozoic.The Baykal-Patomskaya and Namaqua-Natal mobile zones occupy similar positions adjacent to the Siberian and Kaapvaal cratons, respectively, and demonstrate similar modes of metallogenic development: i.e., the early formation of exhalative Pb-Zn-Cu deposits during the early stage and magmatic Cu deposits during the late stage. The more remote mobile belt near the Siberian platform, the Trans-Baykal, is characterized by intensive multi-age mineralization (Wo, Mo, Sn, fluorite), related to a period of tectonic-magmatic activation. The Saldania Belt occupies a similar position near the Kaapvaal craton but is known for its poor Au, and Cu mineralization. It does, however, have some similarities with Trans-Baykal Belt in regard to Mo-W bearing granitoids.The phenomenon of interference of geosynclinal, orogenic, platform, and tectono-magmatic activation regimes is known for the Russian section of the Pacific Ocean Volcanic Belt."

Jan 1, 1994

By M. F. Gallerneault, V. Fallah, A. Howells, W. M. T. Gallerneault

"The occurrence of recrystallization in cold-worked aluminum sheet during the brazing process leads to loss of strength, an inhomogeneous grain structure and reduced corrosion resistance. AlMgScZr alloys are known for their extraordinary recrystallization resistance due to the influence of Sc and Zr addition on their microstructure. Here, we investigate the effect of alloy composition (i.e. Mn, Mg, Sc, Zr content), cold-roll reduction and pre-aging treatment on the recrystallization behavior of cold-rolled sheets at brazing temperatures typically used during the manufacture of heat exchanger units. The analysis of recrystallization behavior is carried out through microstructural characterization and the results are compared with the behavior of a commercial, AA3xxx-based heat exchanger alloy.INTRODUCTION Control of recrystallization is of critical importance during brazing, which is a widely-used joining technique for aluminum alloys in aircraft structures (Heinz, 2000) and automotive heat exchangers (Miller, 2000; Marshall, 1993). Due to excessive local heat at brazing temperatures, the cold work texture of aluminum alloys in the cold-rolled sheets may undergo a local recrystallization process (Marshall, 1993). This leads to the formation of an inhomogeneous microstructure and thus anisotropic mechanical properties (Miller, 2000) and low corrosion resistance (Marshall, 1993) across the sheet. X800, a commonly-used Al-Mn alloy series for automotive heat exchangers applications, has been developed specifically for a higher strength as well as an enhanced corrosion resistance as opposed to the traditionally-used AA3003 alloy (Marshall, 1993). X800 alloys, however, exhibit a low recrystallization resistance at normal brazing temperatures, i.e. 590°C. In contrast, Al-Sc-Zr alloys have been shown to exhibit an extraordinary recrystallization resistance at such temperatures (Riddle, 2004) while also being corrosion resistant and possessing a high room-temperature strength (Fuller, 2002). This has been shown to be due to the formation of coherent, nanoscale Al3(ScZr) precipitates that effectively impede grain boundaries while also exhibiting very slow coarsening kinetics at high temperatures (Riddle, 2004; Jones, 2003; Ocenasek, 2001). In this study, we analyze the recrystallization behavior of X800 alloys under brazing conditions through introducing Sc and Zr into the system as well as varying the Mn and Mg content. The effect of processing route is also studied by introducing a pre-aging stabilization treatment as well as varying the cold-roll reduction prior to the final brazing anneal."

Jan 1, 2018

By Stephen G. Mlot

Technical Study Work ?Technical study work enables informed decisions: -Obtain a higher price for a quality asset -Minimize expenditure on a project that won?t provide adequate returns -Optimize expenditure on a project to capitalize on the potential return

May 1, 2013

By Alfred W. G. Wilson

MR. F. E. LATHE: In studying any subject whatever, one should at least occasionally stand back from the canvas, as it were, and take a broad view of the picture. It is such a view of the subject of industrial minerals that Dr. Wilson has given us today, and, in consideration of our efforts to utilize Canada's resources to the utmost in the present emergency, it seems most timely. I shall confine my remarks on the subject to the resources of the atmosphere and hydrosphere. We seldom stop to realize our dependence upon the atmosphere, not merely as a source of the oxygen we breathe but also of other indispensable elements. As recently as the beginning of the present century, grave concern was felt lest the rapidly increasing population of the world should ultimately starve for lack of the nitrogen required for crop growth. I recently noticed a reference to the Scientific American for March, 1890-just fifty years ago-in which an account is given of work on the fixation of nitrogen, which, said the article, "leads to the conclusion that while cyanides and ammonia may be thus produced experimentally, there are as yet insuperable difficulties in the way of adapting those methods to industrial purposes". Y et, in the early part of the present century, the development of the arc, cyanamide, and synthetic ammonia processes of nitrogen fixation was such as to remove, for all time to come the possibility of a shortage of nitrogen. Today, the atmosphere is by far our greatest source of nitrogen, and the capacity of the nitrogen fixation plants of the world is at least 4,000,000 tons annually-much more than can at present be utilized. Pure oxygen or oxygen-enriched air offers great possibilities in metallurgy and industrial chemistry, but, so far, little application has been made. In a paper presented to the Institute in 1926, 1 pointed out the theoretical savings which could be effected by the use of oxygen in burning carbon-when the gases pass off at 2,460°F., the fuel saving is no less than 50 percent. The use of oxygen on a commercial scale is intimately tied up with the question of refractories, but we should not forget that the possible changes in metallurgical practice by the use of oxygen are truly of revolutionary character.

Jan 1, 1940

By J. E. Danoczi, J. A. Herbst

"Shore Gold Inc. (Shore) is presently designing a diamond processing plant for the Star and the Orion South kimberlite deposits in the Fort à la Corne (FalC) area in central Saskatchewan. The first step in the plant is diamond liberation and occurs in the comminution section. Diamond liberation is the process of breaking up the kimberlite rock, as gently as possible so as not to damage the diamonds.Autogenous grinding mills (AG mills) use a combination of impact crushing, abrasion and attrition to break up the kimberlite. The forces that occur during the actions of abrasion and attrition cause the kimberlites to break up preferentially along lines of weaknesses which offers a “diamond friendly” method of comminution.Hard competent kimberlite is commonly found in the diatreme zone as well as the root zone of the volcanic pipe and is the source of kimberlite for most of the Southern African diamond mines. Softer kimberlite is typically found in and around the crater area of a volcanic pipe and it is this kimberlite that makes up the majority of kimberlite for both the Star and Orion South deposits. These softer kimberlites can be readily broken up using abrasion and attrition imparted by AG mills. In order for Shore to benefit from the softer kimberlite found in the Star - Orion South diamond project, two large (10.97 m diameter x 7.10 m long) AG mills were designed for the comminution section based on extensive test work and simulations by Metso Minerals (Metso)."

Jan 1, 2012

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. Thebatholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering5000km2shows a close connection between a gold-mineralized trend and one of the major shearzones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade(up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W-Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By H. K. Olsen, B. Thomassen, H. K. Schønwandt, L. Grahl-Madsen, H. Stendal

Abstract-The central part of the early Proterozoic Ketilidian orogen in South Greenland consists of an I-type granitoid batholith transected by four regional NE-SW-trending shear zones. The batholith was probably emplaced during subduction, from the south toward the Archaean craton in the north, in a sinistral transpressional system. A regional sediment sampling program covering 5000 km2 shows a close connection between a gold-mineralized trend and one of the major shear zones within the epizonal facies of the batholith. The gold mineralization is not directly related to the major shear zones, but occurs in quartz-veined and silicified second-order structures. High-grade (up to 114 ppm Au over 6 m) low-tonnage mineralization is found within these second-order structures cutting both amphibolites and granitoids. The mineralization is characterized by negligible or small alteration halos. Gold is associated with various element combinations of enhanced As-Bi-W- Cu, which indicate that the mineralization is mesothermal in origin.

Jan 1, 1995

By G. Szilvay, P. Kinnunen, J. Salminen, V. Miettinen, O. Salmi, J. Mäkinen

This paper demonstrates experimental studies on bioprocessing of different waste streams. In Part I of this paper three tailings from mining industry were bioleached with mixed acidophilic culture in order to solubilize valuable metals, like copper, nickel, zinc and manganese to leaching liquor. Bioleaching resulted in > 70 %, > 85 %, 100 % and > 70 % leaching yields for Cu, Ni, Zn and Mn, respectively. However, contaminants like arsenic and chromium were not leached efficiently and they will cause challenges in residual solids and sometimes also in metal recovery from leaching liquor. Bioleaching resulted in 99 % leaching yield for copper. Part II demonstrates mine water treatment and also gold recovery from process liquids with biosorption method. The novelty of biosorption was finding that certain fungal species were able to be cultivated to self-immobilized systems, which are easier to operate than traditional suspended biomass methods. Biosorption resulted in more than 90 % removal for all contaminants, but was also seen to be gold selective.

Jan 1, 2014

By K. M. Wild, C. D. Martin, F. Amann

Peak laboratory strength data obtained from low permeability clay shales/rocks often display a bilinear or non-linear failure envelope. In many of these tests pore pressures are not measured because of issues associated with back-saturation prior to confined compressive loading. In such tests the effective state of stress at failure remains unknown and provides room for speculation. The non-linear shape of the failure envelope may have several reasons including the influence of capillary forces or the tendency of a saturated clay shale to dilate as the confining stress is changed. The former stems from sample preservation, preparation or core unloading effects and represents a partly saturated state (i.e., not representative for the in-situ state); the latter represents the response of a saturated material. This contribution discusses these issues based on a data set obtained from Opalinus Clay specimens, and concludes that without a careful back-saturation processes knowledge of the underpinning reasons for the non-linear failure envelope cannot be obtained.

Jan 1, 2015

This paper generalizes open stopes into elliptical cross sections and applies the results of calculations based on the mathematical theory of elasticity to indicate stress distribution on the boundaries of such stopes. These show both compressive and tensile stresses and provide an ex-planation for the development of excessive dilution in shrinkage toping. Introduction T HE stress pattern around shrinkage stopes is identical with that around other stopes under the same physical conditions. However, a shrinkage stope ends as an unsupported open stope, and the method i limited to the stress range within which the rock is generally self-supporting. If it is acceptable to generalize the outline of a shrinkage stope into an elliptical cross section, then the graphs of Geldart & Udd (1) (see also Panek (2) and Denkhaus (3)) provide a good base for approximating the stress distribution as mining progresses. However, with failure conditions in the walls, the axis ratio, as cut

Jan 1, 1964

By Z. D. Hora

Sedimentary phosphate-bearing rocks are found over a considerable area of so utheastern British Columbia that extends from Fernie east to the Alberta-British Columbia boundary and from the International Boundary northward to the headwatei: s of the Elk River. Phosphatic beds occur at the following four stratigraphic levels: 1. lower part of the Banff-Exshaw sequence of Mississippian age; 2. lshbel Formation of Permian age; 3. base of the Fernie Group of Jurassic age; 4. belemnite bed within the Rock Creek Member of the lower part of the Fernie Group. To date, considerable tonnages of phosphate rock have been proven in the area. However, no commercial production has been initiated because of a relatively low P2O5 grade. Data on assays and thicknesses of the phosphatic beds are in part recalculated from the paper by Telfer (I 933) and in part from assessment reports filed at the British Columbia Ministry of Energy, Mines and Petroleum Resources.

Jan 1, 1984

By Norman R. Ball

"Many people in the mining and metallurgical industries were brought up to embrace Henry Ford's pronouncement that ""History is bunk"" but it is not generally known that the same Henry Ford created and paid for one of the finest technological museums in the Western World. I am aware that many people feel that industry history is something you ask aging executives to do or that history is a clip-andpaste compendium of pictures re-discovered every 25 years or on the occasion of issuing a press release on plant expansion. Moreover, there are many who fear historians as somewhat deranged individuals interested only in corruption, injustice and sensational labour strife. Good history lies somewhere between the controlled P.R. handout and the hysterical attack. Writing good history is a difficult creative act based on the application of experience, insight, wide knowledge and careful reasoning to available evidence. To date, the Canadian mining and metallurgical industries have achieved a great deal but left too little evidence and it is this lack of evidence which must be corrected before it is too late. It is the purpose of this article to stimulate thoughts with regard to archives, one of the more important vehicles for the preservation of such evidence."

Jan 1, 1999

By P. Maltby

"Smelter Feed Preparation Falconbridge Nickel Mines Limited, Sudbury Operations, operate 4 mills and a smelter to produce Bessemer Ni-Cu matte for refining in Norway. Approximately 1400 tons of Ni-Cu concentrate are produced daily which are dried from a filter cake containing 14% moisture to 7.5% moisture pellets. Concentrate drying is done by 4 rotary dryers as shown in the 'Dryer Performance Data' at four separate locations. The dryers all form part of the feed preparation stage prior to sintering.The rate at which concentrate can be produced through the Sinter Plant largely depends on the quality of the dried product which makes up the feed. A feed consisting of mostly hardened pellets will sinter much faster than a feed which consists of broken pellets and dust. Dryer products require:1. Good green strength to survive shipment and handling.2. Correct moisture content.3. Sizing within a range ideally from 1/4"" to 10 mesh in diameter.Dryer performance data is shown in Table 1. Capital costs between the two types of dryers are comparable with the Roto-Louvre producing generally a larger better-formed pellet. Dryer feeds differ in that at both Hardy and Fecunis, Ni-Cu concentrate filter cake is the only feed while at the Falconbridge slurry plant the dryer feed can consist of up to 10% by weight of smelter flue dust resulting in a combined concentrate-dust pellet for feeding to the Sinter Plant. To the Falconbridge Sinter Plant dryer, dust and limestone are added for the smelting process in addition to Ni-Cu concentrate."

Jan 1, 1972

By Inga Tuzovskaya1i

Three types of gold species were observed for gold-zeolites, prepared by reduction of ionexchanged Au species in a series of zeolites: (i) Au3+cations, (ii) neutral Au0 n or charged Aus+ n clusters suggested to be inside the zeolite channels, (iii) Au nanoparticles with diameter varied from 2 through 20 nm located on the external surface of zeolite microcrystals. Contribution of the gold species formed in zeolite after the ion exchange was found to depend on zeolite type, acidity of zeolite, temperature of reduction and time of storage of the exchanged and reduced Au-containing zeolites. Au3+ ionic species and clusters Aun were formed after the ion-exchange procedure (in contrast with the familiar production of Agn in same zeolites). Gold nanoparticles were observed only as the result of reduction of the Au-exchanged forms at elevated temperatures due to reduction of Au3+ species and aggregation of clusters.

Oct 1, 2003

By R. A. L. Drew, J. P. Immarigeon, F. Jalilian, M. Jahazi

In the present work TLP bonding of Inconel 617 is investigated. The influence of the main processing parameters i.e. time and thickness of the interlayer were studied with optical and scanning electron microscopy. Boron containing interlayers with two different thicknesses were used and the influence of various holding times from 5 min to 24 hours on the microstructure of the bond region was investigated. The results indicated that, for the testing temperature of 1065°C and holding times above 2 hours with an interlayer of 25.4 microns thick no liquid phase was observed. The same phenomenon occurred only after 6 hours for a 76.2 microns thick interlayer. Precipitate growth started at grain boundaries and continued inside the grains. The composition, size and morphology of the precipitates were studied using electron microprobe analysis. No noticeable changes were observed in the grain size of the base metal with increasing holding times.

Jan 1, 2004

By Ch. Wenzl

Anodes must have a certain physical and chemical quality in order to provide uniform anodic corrosion and meet the requirements of electrorefining, i.e. to achieve a high current efficiency, low energy consumption, low amount of anode scrap and low effort together with high cathode quality. Various properties of the anodes can be influenced directly by the casting process, which is the interface of pyro- and hydrometallurgy of copper. The aims of anode casting ? high output and long mould lifetimes ? are not consistent with good physical anode quality. The physical requirements of an anode are smooth surfaces, uniform weight and thickness, minimal edge effects, minimal distortion of the body and the lugs, as well as a homogeneous microstructure, in order to achieve uniform dissolution behaviour. The chemical quality of the anode copper is a task of electrorefining operations, but the elemental distribution within the anodes, which should be as homogeneous as possible in order to provide uniform anodic corrosion, can be influenced by the casting process.

Jan 1, 2007

By K. Waters, A. Navarra, T. Grammatikopoulos

Strategic decisions to develop a mineral deposit are subject to geological uncertainty, due to the sparsity of drill core samples. The selection of metallurgical equipment is especially critical, since it restricts the processing options that are available to different ore blocks, even as the nature of the deposit is still highly uncertain. Current approaches for long-term mine planning are successful at addressing geological uncertainty, but do not adequately represent alternate modes of operation for the mineral processing plant, nor do they provide sufficient guidance for developing processing options. Nonetheless, recent developments in stochastic optimization and computer data structures have resulted in a framework that can integrate operational modes into strategic mine planning algorithms. A logical next step is to incorporate geometallurgical models that relate mineralogical features to plant performance, as described in this paper.

Jan 1, 2017

By J. H. Schloen

"One of the most important phases in Canada's relatively rapid development of its metal mining and refining industries was launched in 1928 when the directors of Noranda Mines Limited decided to establish an electrolytic copper refinery ""somewhere in Eastern Canada”. Noranda's president, J.Y. Murdoch, had already evolved the company's ""mine to market"" policy and was determined to prove the economic feasibility of refining Noranda copper in Canada. The time appeared to be ripe as buoyant business conditions continued into 1929. In addition, proven ore reserves at the Horne Mine in northwest Quebec had virtually tripled and the price of copper had reached a healthy 15 cents per pound. Letters Patent incorporating the company bearing the date February 6, 1929 had been granted by the Secretary of State in accordance with an application that specified a capital structure of $2 million divided into 20 000 shares with a value of $100 each. Noranda assumed 70% of the original investment in the proposed refinery, while the Nicholas Copper Company of New York (which later became Phelps Dodge Corporation) and British Metal Corporation Ltd. of London, England, each were responsible for 15%. Nicholas Copper Company agreed to supply the design and to supervise the construction of the refinery and British Metal Corporation would act as sales agent and market the refinery's products."

Jan 1, 1999

By J. Y. Kim, Kenneth Stowe, Stephen Chryssoulis

"A series of flotation tests was carried out on Brunswick Mining ore with various pH modifiers (soda ash, lime, KOH) and added ions (ferric, nitrate, sulphate) in the copper lead rougher circuit. The main objective was to identify downstream effects on sphalerite activation and subsequent zinc rougher flotation. Some significant differences in zinc flotation were obtained. Most notably, soda ash and nitrate ions had a positive impact and ferric ions a pronounced negative effect on selectivity.Selected products from the flotation tests were deslimed at 400 mesh, washed with methanol, air dried, placed in teflon vials purged with nitrogen and stored at -15 degrees C. Numerous liberated sphalerite and pyrite particles were selected under a stereoscope and placed in rows on indium foil. The surface compositions of the particles were analyzed with an innovative laser probe (LIMS). The very small analysis area of the LIMS enables the surfaces of individual grains to be characterized. In addition, the rapid analysis time allows a statistically significant number of grains to be analyzed quickly.Surface lead appears to play a major role in zinc activation/flotation. Possible mechanisms are proposed to explain the variations in metallurgical performance at the different test conditions.IntroductionAlthough the bulk composition of mineral grains is an important consideration for the mineral processor it is ultimately surface composition and topography (edges and dislocations preferred sites for reactions) that control reactivity in flotation and cyanidation (passivation, encapsulation and preg-robbing). Determination of the surface properties of particles from process streams poses a particular challenge for the surface chemist for a variety of reasons, including:"

Jan 1, 1994

By H. J. Chalmers

"Since the advent of large volume flotation machines, Cominco Ltd. has actively studied possible application of such machines to their various milling operations. A number of installations have been made and more are on the drawing board. This paper gives a description of these units, information as to choice of equipment, and information as to operating experience. Mechanical and operating details of six installations are summarized. Three different types of machines are discussed.Pine PointThe original Pine Point zinc flotation circuit comprised conventional roughing with two stages of cleaning. Over the years with increase in feed tonnage there have developed two adverse conditions; namely, a reduction in zinc concentrate grade coupled with an increase in MgO in the concentrate. This resulted in higher freight payments along with more severe smelter penalties. An intensive test program, in 1971, showed that the concentrate grade could be raised by 1.5 units of zinc along with a reduction in MgO from 0.8% to 0.47.. Subsequently this was done by adding two additional stages of cleaning using 16 cells of Denver 200-V's. The project was completed in January 1973 at a cost of $510,000 to give an estimated annual savings of about $390,000.Selection of the Denver Model 200-V was based on minimum floor space requirement, availability, and favourable operational and maintenance experience with Denver 100’s. As it happens it was possible to ""shoe-horn"" the 16 cells into place with a minimum of plant alteration. Some problems have been encountered with a tendency to ""sand up"" at high pH, particularly at the corners. Otherwise operational service has been very good."

Jan 1, 1974