Search Documents

By R. L. Christie

"THE ISLANDS lying north of the Canadian mainland, and the large Boothia and Melville peninsulas, form one of the great archipelagos of the world; this sparsely vegetated and nearly unpeopled region extends about 1,500 miles east to west and 1,200 miles from the mainland to the northern tip of the northern-most island. Sea access to most of the islands is restricted by ice to the summer season, and the 'polar pack' ice of the Arctic Ocean presses the year round against the northwest margin of the archipelago. Although the region is remote, the accessibility has greatly increased through a network of weather stations, airfields and air routes connecting with southern centres.The area considered in this paper is that part of the island region underlain mainly by sedimentary rocks. In broad terms, this includes the land and sea areas of the archipelago and the adjacent continental shelf, but excludes the dominantly 'Shield' terrain of Baffin Island, and of Melville and Boothia peninsulas. An impression of the size and potential of this sedimentary region may be gained by comparing some areas: the land area of islands underlain mainly by sedimentary rocks is over 300,000 square miles or about 50,000 square miles greater than the area of Alberta. The total area of the region, including the continental shelf and the inter-island areas, may be double this figure, and may approximate one-seventh of the land area of Canada."

Jan 1, 1970

By E. G. Joe

"This paper summarizes the main conclusions derived from twenty-two technical presentations made at the 1973 meeting of the Canadian Mineral Processors. Results of two surveys with response from over seventy mines were reported on Canadian milling practice for water re-use and on elimination of cyanide from mill effluents. Water and solution recycle in Canadian mills were detailed for copper, copper-zinc, lead-zinc-copper, nickel-copper, iron and gold mines. Cyanide elimination from mill effluents was reported under current practice and under requirements for further treatment by various other processes. Three recent process equipment entries into Canadian mills have been the on-stream particle analyzer, the new gravity concentration tables for recovery of fine tin and other heavy minerals, and solution-jet slurry equipment for reclaiming ground ore from storage. The principles of operation of this equipment were described along with the practical limitations that were found in their application to mineral processing. Capital costs and milling cost reductions were shown in some operations. Computer control of flotation mill processing was a major item on the program. Four major mining companies outlined their mill process control strategy, computer programs and on-stream analysis equipment. Some capital costs and personnel changes were presented, together with gains in concentrate grade and mill recovery. Recent development work has shown the effect of the type of grinding and of aeration on the recovery of sulphide minerals in flotation. One mining company reported a significant depressing effect on copper sulphide flotation while floating ore ground with mild-steel balls; also, pyrite appeared to be activated in the subsequent zinc flotation step. One company with extensive experience in the application of aeration to copper sulphide flotation showed significant improvement to copper recovery by pre-aeration. Both the effects of grinding and aeration were subject to the constraints of the chemical condition of the ore pulp. The metallurgy of silver recovery by combination grinding - gravity treatment and of gold recovery from a complex gold-sulphide ore were reviewed in two papers on precious metals. The latter paper further described the recovery of gold from the Cottrell collectors and the final disposal of arsenic from the dust collectors."

Jan 1, 1973

By Dougal R. McCreath, Dwayne D. Tannant, Peter K. Kaiser

The Geomechanics Research Centre at Laurentian University in Sudbury, Canada, has undertaken a five-year research program into the design of support appropriate for control-ling damage caused by rockbursts. Rockburst damage mechanisms in Canadian hardrock mines are reviewed and a support design approach is presented. Each element in a sup-port system performs a reinforcing, holding, or retaining function. The desirable load-displacement characteristics for elements in burst-resistant support systems are described, and recommended support systems are presented for a spectrum of rockburst conditions ranging from minor to severe. A support system can be designed to (a) prevent the triggering of aground fall or a rockburst; (b) deform to accommodate the large imposed deformations arising from a rockburst; or (c) absorb the kinetic energy contained in ejected blocks of rock.

Jan 1, 1996

By D. R. Winchester

"I wish to thank you and your organizers for inviting me to address you at this point in time when we are all concerned for the future of the mineral industry in Canada.My topic ""Some Initiatives of Government Assistance to Industry Applicable to Mineral Processing"" is purposely limited in scope. To cover the entire range of initiatives in detail would take me all day, and at best, would be a mere recital of program titles, and a one sentence summary of the contents of the program. As you know, OREE or Regional Economic Expansion, is in the process of being amalgamated with elements of the Department of Industry, Trade and Commerce. We will become Regional Industrial Expansion or ORIE. If the name Canada Dry becomes popular, I don't think we will object as we hope to become a good mixer. The entire departmental thrust has been re-evaluated, and is in the process of being re-constituted to better serve the nation, and industry as a whole. Amalgamation of the industrial, trade promotion and marketing support skills of IT&C, with the regional development orientation and decentralization program delivery mechanisms of DREE, will, it is believed, provide better support to industry on a national and regional basis."

Jan 1, 1983

By A. C. Stevenson

"The most common theory is that, since thyristors, diodes, and insulated gate bipolar transistors (IGBTs) are “solid state” they will live forever. This is not so. They have wear-out mechanisms (e.g. insulation) and other mechanical parts such as motor bearings. These wear-out phenomena can be easily calculated. In this paper we will look at some of the failures and the failure rate of thyristors in power converters to see what affects them and to see what improvements can be made. If converter failures do occur, some simple forensic engineering steps will show if this is the root cause of the problem.IntroductionLook at the general failure rate curve for thyristors, diodes, gate turn off devices (GTOs) and IGBTs shown in Figure 1. We see that there is an initial high failure rate due to manufacturing defects, application problems, and drive start-up stresses that lasts for a few weeks. This is followed by a long period of (hopefully) several years with a relatively low but very slowly rising failure rate. At the end of this period, the devices start to wear out and the failure rate suddenly starts to increase rapidly over a few months. This signals the end of life for the devices in the system. We will start by looking at this end of life area."

Jan 1, 2000

By R Chandramohan

Comminution is the science of size reduction of brittle materials. It is integral to mineral extraction and is one of the most energy intensive processes in the mining industry. There are a number of tests used to quantify the strength of ore, which are then used to size the AG / SAG mill in circuit design. The calculated energy utilized for breakage in these devices is based on the assumptions that the materials treated are of average shape and that the processing equipment is designed to break the ore as efficiently as possible under the given operating conditions. In drop weight tests, it was found that shape significantly influences the measured rock strength. Controlled experiments with variations in blends of rock shape show that mill throughput increases with the addition of weaker shaped rocks.

Jan 1, 2012

By Maurizio Violo, Arjan Beqiraj, Umberto Masi

"Abstract - Four main podiform occurrences of chromite have been distinguished in the ultramafic Bulqiza massif, Albania; they are associated from the bottom to the top with: i) basal harzburgites (lower tectonite sequence), ii) dunitic lens-bearing harzbugites (middle-upper tectonite sequence), iii) layered chromitite-bearing dunites of transitional zone, and, iiii) the stratigraphically lowermost part of the magmatic section. However, only the occurrences hosted by rocks ii) and iii) are economically important.Chromite compositions similar to those of other podiform chromites are bimodal. Thus, chromites from occurrences ii) and iii) are richer in Cr than chromites from the other two occurrences. Accessory chromite disseminated throughout the massif is richer in Fe than orebody chromite, displaying similar range of the Cr/Cr+Al ratios, with accessory residue chromite matching the characteristic (Cr/Cr+Al >0.6) range of type-III Alpine peridotites. Both orebody and accessory chromites show compositional ranges correlating with host-rock compositions, i.e., the Cr-rich chromites are hosted by the most refractory ultramafic rocks. Therefore, the Cr/Cr+Al and Mg/Fetot (Cr/Fetot) ratios of chromite are useful for exploration of high-grade, metallurgical chromite ore at Bulqiza and in other massifs of similar geodynamic setting."

Jan 1, 2000

By Cummings. J. B., R. Haworth

"THE OPERATION of the Potash Company of America, Ltd., at its plant near Saskatoon, Saskatchewan, is the result of many years of exploratory and development work, culminating in the construction of a shaft, milling, concentrating and other facilities necessary to the production of potash in a marketable form.The possibility that potash existed in •commercial quantities in Saskatchewan was first indicated in 1943, although it was not until mid-1946, when Bata Petroleums penetrated a potash bed at its Verbata No. 2 well near Unity that substantial in-ter.est was developed in the possible exploitation of this important mineral product.The Potash Company of America, which is the largest producer of pot-ash in the Carlsbad, New Mexico area, a district that has been sup-plying about 90 per cent of the North American potash demand, be-came interested in the Saskatchewan deposits •at an early stage. Its engineers made an intensive study of the western Saskatchewan area in 1947 and continued their review of operating problems throughout the next three years.""Potash"" is the commonly used general term applied to the minerals of potassium, of which there are several. The most common mineral forms in which it is produced are potassium chloride and potassium sulphate. The potash content of potassium compounds is ordinarily ex-pressed in terms of potassium oxide (K20) equivalent."

Jan 1, 1960

By John J. Laffin

"IN THE BOOK that has been rated the best seller of all time, it is predicted that man will earn his livelihood by the sweat of his brow. Apparently man has accepted the statement as a challenge and has been attempting to refute it ever since, as he continues to transfer the workload to his inanimate servants - the many types of machines and other labour-saving devices that are available to assist or perform for him in the normal tasks of the day. The history of the evolution of the use of energy takes us back to primitive man, who existed in a very low energy environment, the only energy available being his own muscle power. Although man took a great leap forward when he discovered fire, which was used for lighting, heating and cooking, he still depended upon his own muscles for power. Early man's greatest achievement was probably the invention of the wheel, which permitted him to utilize the muscle power of animals. While still in a very primitive state when viewed from the perspective of the twentieth century, man, with fire and the wheel, had achieved a standard of life far exceeding that of his predecessors. Looking beyond the very basic elements of human energy, fire and the muscle power of animals, we find the next additions of energy coming from man's mastery of other elements of nature. The Phoenicians utilized the power of the wind and the Romans adapted the energy of falling water to the water wheel."

Jan 1, 1972

By M. A. Power

The diamondiferous Drybones Bay kimberlite pipe is the largest pipe (900 m by 400 m) discovered to date in the Northwest Territories. The pipe intrudes granodiorite of the Archean age Defeat Pluton and contains crater, reworked crater (epiclastic) and diatreme facies kimberlite. In-situ measurements of seismic p-wave velocity were recorded with in-line refraction arrays over representative areas. Refractions from fresh kimberlite were recorded over epiclastic facies kimberlite in the eastern portion of the pipe and returned an average velocity of 4300 m/s. Refractions from weathered kimberlite were recorded on all lines and returned velocities ranging from 1900 m/s to 2200 m/s. Granite surrounding the pipe returned an average velocity of 5400 m/s. The results indicate that there is a definite contrast in seismic velocities between kimberlite and country rocks at Drybones Bay and suggest that seismic refraction surveys may be an effective means of screening kimberlite targets in glaciated areas underlain by igneous or metamorphic rocks.

Jan 1, 1998

By J. L. Miller, R. W. Burns

This paper sets out the various phases of bringing a merchant bar mill into operation from feasibility consideration through financing, design and scheduling to completion.

Jan 1, 1967

By I. Raheb, M. Y. Debili

"A set of Al-Co binary alloys (with respectively in weight percent 10%, 20%, 30%, 40%, 50% and 60% Co) have been studied by X-ray diffraction at the as compacted state. The structural evolution according to cobalt addition shows special features as the apparition of fcc cobalt and hcp cobalt beside aluminium in some cobalt compositions of the Al-Co mixtures using only cold compaction without sintering at high temperature. Figure 1 Cobalt is not a common alloying element in aluminium because its solubility is very low [1]. According to the pressure-temperature phase diagram, Co is known to exist in two allotropic forms: a low-temperature hcp phase and a high-temperature fcc phase [2-3]. At room temperature, Co is stable in the hcp form but it transforms to the fcc form when it is heated to above the transition temperature 695K. Powder aluminium and cobalt (99.999 %) were used in the proportions defined according to the required compositions. The total mass of the samples to be elaborated was between 8 g and 10 g. Cold compaction of mixed powder (Al-Co) under an uniaxial load of 10 MPa has been achieved to obtain a dense product (60%)."

Jan 1, 2015

By Manouchehr Oliazadeh

Talc is used as a gelating, diluting, antimould and softening agent in the pharmaceutical industries. This article reviews efforts made for producing pharmaceutical grade talc from a mine located in the west of Iran, called Masoud Abad. Reaching to the pharmaceutical standards, was the principal goal of the talc beneficiation. Methods such as flotation and leaching were applied to eliminate the impurities. Considering to the negligible Fe content of the ore, the major impurity was calcium carbonate and to some extent dolomite. Depressants used in froth flotation were dextrine, quebraco and sodium silicate. Variation of collectors such as oil petroleum, paraffin, stearic acid were also used. After optimization of the effective parameters, followed by two stages of flotation (rougher and cleaner) acid leaching process was also applied as a complementary step to remove the impurities. CaO impurities in the sample was 11.63% which reduced to 1.03% after two stages of flotation, and finally reached to 0.03% CaO by leaching process. This figure is more lower than the world pharmaceutical standards (i.e. <0.6 % CaO). The highest recovery was 55% at the best conditions. Other impurities (i.e.As, lead, heavy metals ,?) which were at standard levels, confirmed by the authorized health organizations.

May 1, 2001

By M. C. Walton, W. Roelofs

ABSTRACT: In most cases, a refractory repair involves dealing with used refractory linings above shoulder height, defining these as overhead refractories. This paper details a method of personnel protection involving a low-pressure inflatable balloon system, installed to prevent the dislodgement and freefall of in-situ refractories. This system has been successfully applied to numerous types of vessels in the process industries in the last three to four years. This paper, prepared for the CIM Conference of Metallurgists held in Vancouver, British Columbia in October 2010, outlines details of the system and gives examples of successful applications.

Jan 1, 2012

By R. Gutray, J. E. Grainger

This paper deals with the use of a cement-deslimed mill tailings mixture for a scraping floor in cut-and-fill stopes at Madsen Red Lake Gold Mines Limited. It describes the mixing and placing procedures and the precautions used with respect to the floor while mining in the stopes. Details of the mix are presented, and advantages and disadvantages discussed. The paper concludes with a brief outline of the costs.

Jan 1, 1966

By Nural Kuyucak, Bohumil Volesky

"Extensive screening revealed a seaweed (alga) biomass type which in its non-living state possesses a very high cobalt sequestering capacity comparable to that of activated carbon and the ion-exchange resin currently used in the cobalt production process. Performance of the new bio-sorbent material was studied by examining its equilibrium metal uptake isotherms generated under different solution conditions such as initial cobalt concentration pH, temperature, and the presence of selected cations and anions. The rate of cobalt uptake was determined, which is a crucial parameter for recovery process design. Almost all cobalt sorbed can also be desorbed with a solution of CaCI2. The bio-sorbent material can be used repeatedly in the sorption-desorption cobalt concentration process. IntroductionIt has been well documented that certain types of microbial biomass, living or non-living, possess a high potential to sequester and accumulate inorganic ions present in aqueous solutions. Metal concentration by microbial biomass from a solution is termed bio-sorption. This phenomenon is quite complex and includes adsorption of metals onto the surface of a microorganism and/or into the cellular structure in combination with ion-exchange, complexation, and/or micro-precipitation. Bio-sorption is generally considered to be a rapid physical/chemical process. The cell wall structure is porous and allows metal ions, as well as large organic nutrient molecules, to pass freely through. Polysaccharides of the cell wall could provide binding amino, carboxyl, phosphate and sulphate groups. In addition to these functional binding groups, polysaccharides often have ion-exchange properties. Sometimes, bivalent cations, such as Ca2+ or Mg2+, help the formation of ionic bond bridges between the negatively charged cell surfaces and positively charged cations in the solution, Proteins in the cell wall could offer functional groups and also offer peptide bonds to bind ions. Interactions between metal and the cell wall components are responsible for the sequestering of metals by way of bio-sorption. Many metals feature a complex solution chemistry and it is not always possible to determine what ionic species are actually present in the solution. The equilibria involved are dependent on pH, concentration, the anions present and other factors. The transport system for the ions are sometimes dependent on both temperature and energy. Biosorbent material could also be regenerated for multiple reuse."

Jan 1, 1988

By Cindy Schiewek

Industrial injury occurrences are an ongoing concern for Mine Operators. Along with the personal suffering of injured workers comes an increase in compensation and productivity costs. Growing recognition of repetitive stress and bodily injuries, accompanied by recent studies, validates the assumption that a relationship exists between ergonomic injuries and machine design. Intuitively, there is a belief that an ergonomically designed machine will reduce repetitive stress injuries through design and education however; quantifying this belief has been a challenge for Mine Operators. Sandvik Tamrock has undertaken a project aimed at developing a business model to assist in quantifying the benefits of ergonomic intervention. This model focuses on distinguishing and quantifying this method of intervention to allow for a better evaluation of the machine. For simplicity, the project initially focused on the Face Drill Jumbos. The target of the project was three fold: !" Recognition of the cost drivers for compensation; ergonomic injuries !" Identification of the relationship between ergonomic machine design, and the decrease of the negative effects associated with the cost drivers !" Systematic prioritization for ?prevention by design? The project findings substantiate the expected reduction in injuries and compensation claims. Based on all ergonomic intervention studies conducted, each case showed a reduction in compensation cost; through prevention by design, one can reduce the amount of potential risk. The paper addresses the resources and methodology used, along with the findings and its relevance to the issues that face the Mining industry.

May 1, 2003

By Paul B. Batten

Shutdown is a generic term for what may be called an Outage, Turn Around (TAR) or Overhaul etc. Running a plant shutdown well has always been key to the financial contribution of a mine. However, something important has changed. The post pandemic reality is that it is harder to retain workers and many of those near retirement just didn’t come back to work. This is creating a shortage of experienced people and a workforce that changes employers easily. We are seeing the impact of this manifested in the erosion of established maintenance and supply chain processes that now struggle to yield the plant runtime that could once be taken for granted. The scope, cost and duration of a shutdown varies widely depending on the nature of the work and the equipment being renewed. The PM of an electric shovel might require a week of downtime and cost $100,000. A gold plant may need to go down for 3 days when its time to change mill liners and cost $500,000. A turnaround in a refinery can take more than a month and cost multi millions. Despite the huge differences.

Jan 1, 2023

By T. G. Joseph, A. Sharma

ABSTRACT: Ultra-class haul trucks operating in oil sand face operational and maintenance issues as a result of soft underfoot conditions (Joseph, 2002). With exposure to frequent high g loading events, tire life is reduced due to sidewall belt fexure and frequent ground contact. Therefore, an improved under-standing of the interaction between tires and oil sand is needed. This paper examines the outcomes of a series of static and cyclic loading tests, performed using a scale tire on rigid, sand, and oil sand surfaces. Geometric predictions are made regarding the footprint area and vertical deformation of an ultra-classtire on similar surfaces.

Jan 1, 2011

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015