Search Documents

By Jamie N. Burdeski, Susan E. Hartfield-Wünsch

Aluminum sheet use has been steadily increasing in the automotive industry to achieve mass reduction and improve fuel economy. One significant manufacturing challenge for aluminum sheet implementation is the reduced formability compared to the steel alloys it replaces. This paper includes friction results from the draw bead simulator (DBS), twist compression (TCT) and strip draw (SDT) tests, for two oil based lubricants and four hot melt lubricants. Formability testing was done with the same lubricants and materials, testing in pure stretch with a hemispherical punch, and in draw with a breadpan shaped die.

Jan 1, 2015

By C. R. Fast, G. C. Howard

The loss of fluid to the formation adjacent a fracture governs the areal extent of the fracture and the success of hydraulic fracturing as a production stimulation technique. The three flow mechanisms which control this loss are the result of the viscosity of the fracturing fluid and the permeability of the formation to the fracturing fluid, its wall building properties, and the combined effects of viscosity and compressibility of the reservoir fluid. The effects of these flow mechanisms can be evaluated in terms of a fracturing fluid coefficient, the fundamental concepts of which are developed in the paper. The fracturing fluid coefficient, which may be used in calculating the areal extent of fracturing, affords a direct measure of the effectiveness of fracturing fluids. The area of hydraulically created fractures is in-creased as the coefficient is de-creased. The fifteen-fold variation noted in this coefficient for the commercially available fracturing fluids tested resulted in a six-fold difference m the calculated areal extent of the fracture system.

Jan 1, 1961

"With the globalization of the mining industry, many companies are now seeking to invest in underground diamond mines, with the purchase of small diamond pipes being seen as particularly attractive. However, recent experiences in South Africa have shown that many projects fail due to a lack of awareness of the hazards associated with diamond mining. In this paper three significant hazards are dealt with — mud rushes, block crushing, and implementation of an inappropriate mining method. Measures that assist in the prevention of these three hazards are given.IntroductionFor over a hundred years, South Africa has been seen as the centre of the diamond mining industry, possibly having the largest number of operational underground diamond mines in the world. Despite the fact that this industry has been dominated by large mines of De Beers Consolidated Mines Limited, many small underground mines have operated profitably for a number of years, exploiting diamondiferous fissures and pipes. In the last decade there has been renewed interest in these small operations from international companies. However, many of these projects have not realized their full potential owing to a lack of appreciation of the hazards inherent in the operation of a diamond mine.Hazards Associated with Diamond MiningIn the development of a diamond mine, the mining company must be aware of the hazards associated with diamond mining. There are three main hazards: (1) mud rushes; (2) block crushing; and (3) selection of an inappropriate mining method (not a natural hazard, but a planning induced hazard). Each of these hazards will be dealt with in turn in the following sections."

Jan 1, 2000

By J. A. Irvine

In 1972, a cooperative program to map and estimate the quantity of Tertiary coal resources in southern Saskatchewan was initiated by the federal and Saskatchewan governments. More than 700 exploratory boreholes were drilled over a two-year period, and data were obtained from other organization s on an additional 1500 boreholes in the area. Stratigraphic data and data on each coal seam penetrated in the boreholes, along with technical and location data for each borehole, were stored in a computer data base for convenience of retrieval, modification and manipulation. Programs and program packages were developed or adapted to: (1) select borehole information defined by variable retrieval parameters from the data base; (2) calculate derived information , such as overburden ratios. cumulative net coal thicknesses , mean weighted center of gravity of coal seams in each borehole, etc., from the selected data ; (3) produce posting maps of either selected data or calculated information in various combinations at variable scales on a plotter or CRT display; (4) produce contoured structure, isopach or ratio maps , and perspective diagrams as appropriate , utilizing plotter or CRT display; (5) calculate and categorize quantities of coal in place within user- defined "mineability-economic-reliability" limits. The emphasis in computer utilization was placed on geological credibility of the results and ease of operation by relatively untrained geological personnel, resulting in extensive use of interactive methods. The single most important benefit derived from using computer-assisted procedures is the ability to produce new maps and quantity estimates rapidly and inexpensively as a result of availability of new data or/and changes in external criteria which impose economic or mineability constraints.

Jan 1, 1978

By John J. Barakso

A summary of geochemical dispersion processes is presented. Secondary and tertiary dispersion of uranium was examined at several uranium prospects in British Columbia. The vertical migration of uranium from bedrock (primary dispersion) through overburden into the various soil horizons, and into snow and plants, was studied, and relationships were sought to explain the dispersion patterns in the secondary and tertiary environments. Soil developments were examined to obtain information on factors affecting the dispersion of uranium in soil profiles and tertiary substances; samples were analyzed for a number of elements. Biogeochemical data indicate that plant geochemistry is a possible exploration aid in areas of heavy overburden owing to the high selectivity of certain plants for specific elements. Some new data on the geochemistry of snow are discussed as a matter of research interest in the tertiary dispersion of uranium. Analytical techniques and problems are discussed, particularly extraction techniques, which must be carefully chosen to give reliable information on uranium dispersion.

Jan 1, 1979

By A. W. Johnston, R. E. Barrett

"The Central Patricia mine is in the greenstone belt north of lake Sc. Joseph in northwestern Ontario. It is 90 miles north of Allanwater on the Canadian National railway and 220 miles east of the Manitoba boundary. The unusual feature of the ore of this mine is that the gold does not occur in quartz but in sulphide minerals filling fractures in iron formation.AREAL GEOLOGYThe rocks of the area in which the mine occurs belong to the Early Precambrian. They consist · of andesite lavas and tuff interbedded with greywacke-like sediments and iron formation . A siliceous phase of the sediments lying north and south of the greywacke enclosing the ore-bearing iron formation in places resembles a sheared and sericitized quartz porphyry. This is shown in the legend of Fig. 1 as quartz porphyry and quartzite, but it is possible that the quartz porphyry-like phase is sediment. A northwest- striking dyke of diabase crosses the property 3,000 feet east of the shaft ( Fig. 1).IRON FORMATIONAlthough there are numerous bands of iron formation in the v1cm1ty of the mine, ore has been found to date in only one main and two lesser zones. The iron formation bands range in width from a few inches to 60 feet, and are interrupted along their strike by gaps that are parallel and rake to the east at about 65°. The iron formation is definitely banded and laminated."

Jan 1, 1954

By Balmer Neilly

Early in my term of office it was announced that my Presidential Address would make particular reference to the subject of Mine Taxation in Canada. With this purpose in view there was drafted a Balance Sheet and Earnings' Statement of a Gold Mining Company. This in turn was submitted to the Dominion Income Tax Authorities in Ottawa and to the Minister of. Mines of each of the several Provinces of Canada. The response to the invitation was not as complete as we had hoped it would be, but the figures that were obtained will be presented during the present meeting, and they constitute, I hope, a sufficient basis for extended study and additional enquiry during the year to come ( 1) . In the form letter that accompanied our request to have the submitted earnings assessed, I made the following assertion: "In this work we have three objects in mind. 1.--We will get direct comparison between the different Provinces in Canada. 2.-We will in this way educate our members concerning taxation as it affects the mining industry. 3.-We will publish the details as to how the assessment is calculated by each body, so that a Mine Manager in the most remote district will have a ready reference to guide him in his annual return to the taxing bodies. As things stand, there is no intention of making this a basis for a critical attack on the present rates assessed. It is intended as an authoritative summary of actual conditions as they presently exist".

Jan 1, 1934

By Noel Brien, O&apos

General: National Asbestos Mines Limited has operated an asbestos mine and mill near Thetford Mines, Quebec, since 1958. As a result of additional exploration of the orebody in 1962-63, it became apparent that long-range mining plans would have to be revised to allow for a large increase in both ore and waste tonnages. It was decided that the task of checking out possible mine designs could best be analyzed by a computer to obtain data from which an optimum open-pit configuration could be plotted. Object: It was desired to arrive at an optimum open-pit configuration with an over-all pit slope of 45 degrees and a minimum operational width of 200 ft. at the bottom. Calculations were based on assay values from diamond drill holes in cross sections of the mine. The computer's assignment was to select and describe, by coordinates, the optimum cross section for the mine. Mine engineers then assembled the various optimum sections to produce the pit outline. As this would not necessarily result in a practical mining arrangement, the computer also provided alternate solutions,

Jan 1, 1965

By J. W. Reynolds

Use of crushed waste rock recovered by sink-float separation from normal ore production for backfill is an established procedure at Commco's Sulhvan mme, Kimberley, British Columbia. Need for a safe method of placement in voids which were difficult to reach by gravity methods led to a co-operative venture with Radmark Engineering Ltd. in the development of a workable pneumatic transportation system for rock material. This paper reviews work done to date in a current program, and includes comments on the nature of the fill so placed, options for cementing such fill, implications for other aspects of mining and references to other applications of the system by other organizations who exchanged experiences with the Sullivan mine staff during the five-year period reviewed.

Jan 1, 1972

By Feng Xue, Mi Xujun, Peng Lijun, Yin Xiangqian, Liu Dongmei, Xie Haofeng, Huang Guojie, Yang Zhen

The Age-hardening Cu-Cr alloys are extensively used in integrated circuit lead frame, railway contact wire, resistance welding electrode and continuous casting mold copper plate, owing to having an excellent combination of high electrical or thermal conductivity and high strength. High temperature performance is very important during the service process. Effect of Magnesium and Zirconium on softening behavior of Cr-Cr alloy are investigated by scanning electron microscopy (SEM) and transmission electron microscopy (TEM). During the softening process in the Cu-Cr alloy, the recrystallization process, grain growth and Cr precipitates coarsening are observed. The addition of Mg or Zr to the Cu-Cr alloy, the resistance to elevated temperature can be significantly improved, owing to being restrained the growth of the precipitates by segregating along precipitates surface. INTRODUCTION Age-hardening Cu-Cr system alloys can be widely uesed in many fileds such as electrodes for spot welding (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012), intergrated circuit lead frame (Hatakeyama et al., 2008; Cheng, Shen & Yu, 2013; Zhou et al., 2016; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003; Cheng, Yu & Shen, 2014; Zhang et al., 2016; Li et al., 2007) and railway contact wire (Cheng, Shen & Yu, 2013; Zhou et al., 2016; Chbihi, Sauvage & Blavette, 2012; Liu et al., 2006; Pang et al., Xia et al., 2012; Wang et al., 2009; Huang et al., 2003), because it has high strength, good electrical and thermal conductivity. The precipitation behavior of binary or ternary Cu-Cr alloys had been investigated by many researchers (Chbihi, Sauvage & Blavette, 2012; Peng et al., 2017; Batra et al., 2002). In addition, to obtain additional mechanical properties without much deterioration in electrical conductivity, trace addition of alloying elements like Zr, Ag, rare metals (Y and Ce) and Mg are added into Cu-Cr alloy. The addition Mg to Cu-Cr alloy accelerated the process of precipitates nucleation and restrained the growth of the precipitates by segregating along precipitates surface during aging, which enhanced the stability of the deformation microstructure and improved the mechanical properties of the alloy (Zhao et al., 2018). Additional zirconium in Cu-Cr alloy enhances the strength by the decrease in inter-precipitate spacing of Cr precipitates and the formation of Cu5Zr phase (Chihiro, Ryoichi & Kazue, 2008). Owing to the decrease in inter-precipitation spacing of Cr precipitates and to the Ag-atom-drag effect on dislocation motion, the addition of Ag can increase in strength, stress relaxation resistance and without much deterioration in electrical conductivity (Chihiro, Ryoichi & Kazue, 2008). The enhance in strength and electrical conductivity of the Cu-Cr-Zr alloy by adding Ce and Y elements are attributed to removing oxygen and sulfur from as-cast alloy (Li et al., 2006). However, the effect of Mg or Zr element on microstructure and properties of Cu-Cr alloy during the softening process are not clear. Therefore, Microstructure evolution and properties of a Cu-Cr systems alloy were investigated in detail by OM and TEM. The Relationship between microstructure and properties of Cu-Cr systems alloy was also discussed.

Jan 1, 2019

By W. A. Alexander

Introduction In the course of a programme of research on beryllium in progress in these laboratories, knowledge of the recrystallization temperature became necessary. As the information is not available in the literature, the determination of this temperature for metallic beryllium was undertaken. By the reduction of grain size through working and recrystallization and the probable simultaneous induction of preferred orientation, it was hoped to improve the working properties of beryllium at lower temperatures. The recrystallization temperature is usually determined by observing the lowest temperature of annealing at which new crystals are formed in severely cold-worked metal or alloys. This temperature is profoundly influenced by the following factors: the purity of the metal, in the case of an element, or the composition of the alloy; the degree of straining or working; the temperature of straining; the original grain size; and the time held at the annealing temperature. The observed temperature is lowered by higher purity, more severe straining, lower temperature of working, smaller original grain size, and longer time of annealing. Beryllium presents special difficulties in that the percent elongation in tension is effectively zero, so that ordinary squeezing or rolling was not possible. A possible means of straining was suggested by the fact that indentation hardness tests could be made. It was known from earlier work that the metal could be worked at elevated temperatures, so that working at the lowest feasible temperature and quenching might also be a means of producing strain. The purity of the metal is also a point of some uncertainty in the case of beryllium. Losano has prepared 99.96% Be which appears to be the best reported. Distilled metal used in the present work approached this purity. However, by analogy with other metals, residual impurities may have a pronounced effect on the recrystallization. Further purification of beryllium would evidently entail considerable difficulties due to the highly reactive nature of the metal, and was not attempted.

Jan 1, 1947

By Alvaro Diaz

Introduction, who is Teck Red Dog and Quebrada Blanca Mines Uniqueness of environment Arctic versus High Altitude Conditions Logistical challenges People and Stakeholders Conclusions

May 1, 2013

By B. Drew, K. Budna, C. Wenzl, D. Gregurek, A. Spanring

"The metallurgy of nickel and cobalt and of copper is closely interlinked when processing sulfidic Ni-Co ores and Cu-Co ores. The respective furnaces are typically lined with magnesia-chromite refractories, which are exposed to multiple and complex stresses. The selection of the processing route, furnace type and slag system will be dictated by the specific ore type available, this will determine the individual refractory wear mode. This paper evaluates the common refractory wear mechanisms, namely infiltration, spalling and chemical attack by various slag systems, as well as sulfur attack, as observed when processing primary sulfidic ores. All these wear parameters, which are discussed in this paper, lead to a severe degeneration of the brick microstructure and a decreased lining life. Therefore, a detailed investigation and understanding of the wear mechanisms through “post mortem studies” is an important prerequisite for the refractory producer. Based on such research results, combined with specific process knowledge, appropriate brick lining solutions for nickel and cobalt processing furnaces can be recommended.INTRODUCTION The metallurgical production of cobalt and nickel and of copper is closely interlinked to the mineralogy of the respective ores: cobalt is found in African Cu-Co ores as well as in Co-rich nickel ores (laterites and sulfides). Also, Co-bearing secondary raw materials contain the mentioned elements in different contents. In pyrometallurgical processing of sulfidic ores, cobalt is generally recovered as a by-product during the production of copper and nickel, whereas it is normally not recovered separately during the processing of nickel laterites but remains in the FeNi product. Besides various hydrometallurgical production routes, the pyrometallurgical processes involved comprise smelting (i.e., production of a Cu-Ni-Co-Fe matte in electric or flash furnaces), converting and refining (i.e. removal of Fe and S as well as other elements from matte by oxidation). The ongoing trend to use higher oxygen enrichment in process air enables higher intensity processes but also increases the oxidation potential in the vessel. Therefore, during smelting and especially during the oxidative treatment in converting and refining, some amounts of valuable metals are also transferred to the slag in their oxides form. A subsequent slag treatment is then applied for recovering valuable metals from the slag, namely allowing an economic material stream handling and minimizing metal losses. This is often done in a slag reduction furnace. Additionally, copper and nickel are very good collectors for precious metals and platinum group metals (PGMs) - therefore, depending on the content of these metals, an additional refining process is used to recover these valuable metals from the matte or metal phase (Elvers et al., 1997; Davenport et al., 2002; Crundwell et al., 2011)."

Jan 1, 2017

By Farzad Mohammadi, David Kratochvil, Patrick Littlejohn

"With more rigorous regulations being enacted in the mining industry, a need exists for cost effective and environmentally compliant technologies to remove selenium from mine impacted waters to ultra-low concentrations. Existing selenium treatment methods have high life cycle costs, introduce risks of acute fish toxicity, and produce biological waste residues that represent future liabilities. Furthermore, achieving selenium discharge limits of less than 4 ppb is a challenge for existing technologies. Selen-IX™ is a technology developed by BioteQ that selectively removes selenium from mine impacted waters to less than 1 ppb. The technology is purely physico-chemical and takes advantage of the basic principles of ion exchange and electrochemistry. Unlike conventional electrocoagulation that removes suspended solids and breaks emulsions or oxidizes heavy metals, the electrochemical process employed by Selen-IX™ relies on creating conditions where iron acts as a highly effective reducing reagent transforming selenium from a dissolved species into elemental selenium bound in a solid phase. The iron-selenium by-product of Selen-IX™ is an inorganic, non-hazardous and chemically stable solid. Due to their high iron content, the solids produced by Selen-IX™ are of interest to the steel making industry as a low cost feedstock. This offtake potential can not only reduce the life cycle cost of selenium removal by reducing disposal costs but more importantly, eliminate the risk of future environmental liabilities. In this paper, the basics of Selen-IX™ technology are presented along with results of successful piloting on streams from coal and copper-gold deposits.INTRODUCTIONVarious contaminants are released into mining wastewater during the extraction and processing of metals. One such contaminant is selenium. A naturally occurring element found in rocks and minerals, mining activities accelerate its release into the environment. Selenium in trace quantities is essential to all life forms but at higher concentrations it can be harmful, especially to aquatic life where selenium bioaccumulation can lead to reproductive deficiencies."

Jan 1, 2016

By P. Chu, J. A. Finch

The formation of small bubbles in flotation is usually accomplished by the use of frothers, or sometimes is due to the presence of inorganic salts in the process water. The effective mechanism associated with the presence of these solutes is generally considered to be coalescence inhibition. However, recent work has demonstrated that the presence of frothers and salts also reduces the size of bubble at the initial formation stage. In this paper we adapt the same experimental setup to investigate the time that it takes for a bubble to form; for a known system power input, the energy to form a bubble can then be estimated from the time. The hypothesis is that the presence of frother and salt will reduce the time for a bubble to form, which can be interpreted as an added energy component being derived from the solute. Testing different types and concentrations of frothers and salts, the hypothesis is supported: the mechanical energy required to form a bubble decreases by about 10% in the presence of these solutes.

Jan 1, 2015

By D. O. Tansey

This paper will describe the mechanisms involved in delay blasting and how they are applied with the use of D.S.B. It will examine the control of potential damage resulting from detonations, and show how good fragmentation and efficient recovery of this material blasted can be achieved

Jan 1, 1979

By Ainul Akhtar, Steve Cockcroft, Jixiang Xu, Daan Maijer, Lu Yao

"Nitrogen rich Ti-N inclusions are one of the more difficult inclusions to remove during liquid metal refining of titanium. If present in the final component, they can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading. Understanding the kinetics of dissolution of Ti-N particles during consolidation/melting of titanium can help us better operate and design the melting processes to minimize their occurrence in Premium Quality Titanium production. A numerical model based on finite difference method has been developed to calculate the dissolution of a spherical Ti-N particles in molten titanium. Analytical solutions were used to verify the finite difference code for calculation of concentration profile and the dissolution of spherical solids. Taking into account the limitations in these approaches for the different cases examined, the invariant field approximation showed good agreement with the results from the numerical analysis. Evolution of the size of a spherical Ti-N particle during dissolution was predicted by the numerical model and the particle dissolves in 163 s.INTRODUCTION Properties like low density, high specific strength and excellent corrosion resistance make titanium attractive for a variety of applications. Key characteristics in the processing of titanium and its alloys include its high sensitivity to impurities, especially atmospheric oxygen and nitrogen and its high reactivity in the molten state. Nitrogen rich inclusions Ti-N, also known as Type ? or hard alpha defects, usually have substantially higher hardness and lower ductility than the surrounding material. Because they can act as fatigue initiation sites, Ti-N inclusions can significantly decrease the mechanical performance of titanium and its alloys in applications involving cyclic loading, even in minor amounts (tenth of a percent) (Lampman, 1990; Moiseyev, 2005; Lütjering & Williams, 2007). Ti-N encompasses as a broad range of nitrogen contents from a few wt% up to stoichiometric TiN. The liquidus temperature of Ti-N titanium increases substantially with increasing nitrogen content. Consequently, depending on the concentration of nitrogen, the melting point of Ti-N inclusions can be above bulk liquid metal temperatures during melt processing. Thus, removal of Ti-N defects hinges on dissolution and not melting."

Jan 1, 2017

By F G. Cooke

"This paper describes a medium-sized copper mine's results in making innovations and changing operational practices to combat increasing expenditures due to higher labour and supply costs, extended workings, scarcity of experienced manpower and problems created by deteriorating ground conditions.OPEMISKA COPPER MINES (QUEBEC) LIMITED is located at Chapais in the Chibougamau area, in central eastern Quebec, approximately 300 miles north of Montreal and 150 miles north west of Lake St. John. The latter area, developed by lumbering and farming, has supplied the majority of the employees, who, with training and experience and a desire to work and improve themselves, have become the backbone of the Company's 600 personnel.Opemiska began production in 1954 at a rate of 400 tons per day, using diesel power and road transportation. The rate was progressively increased and, by 1959, with hydro-electric power and rail transportation, the mine had reached its present production rate of 2,000 tons per day. It has produced concentrates containing over 430 million lbs of copper."

Jan 1, 1968

By ByongPil Lee, Changkyu Lee, Jin Gyun Park, Hyung Sub Eom, Sung-Koo Jo, Jae-Young Lee, Gilsoo Han

"A new hydrometallurgical process for nickel extraction from a low grade laterite ore such as limonite has been developed by RIST and POSCO. This POSCO Nickel Extraction Process (PosNEP) consists of five main processes: ore reduction using hydrogen as a reductant; acid leaching at atmospheric pressure and temperature; cementation by the use of reduced-ore seed; production of the main product such as ferronickel or a high purity nickel compound; and production of by-products such as cobalt and iron in the forms of cobalt sulfate and iron oxide. In addition, hydrogen produced in acid leaching and hydrochloric acid regenerated in pyrohydrolysis for iron oxide production can be reused in the process, which makes PosNEP more cost-effective. The performance of PosNEP has been proven through pilot tests, showing that this process is economically and technically viable. In this paper, basic concepts and detailed test results of PosNEP are shown.INTRODUCTIONNickel has been extracted from two types of ore, sulfide and oxide ore. Nickel and cobalt usually occur together in the ores. The principal ore mineral of the sulfide is pentlandite, (Ni,Fe)9S8, which is easily beneficiated to produce sulfide concentrates(Moats & Davenport, 2014). These concentrates are usually treated by smelting and converting to make a matte. The produced matte is then purified through either hydrometallurgical or pyrometallurgical processes to produce high-purity nickel. In general, this process for sulfide ore has been known as a more cost-effective process than that for oxide ore.The oxide ore is laterite comprised of two different ore types, saprolite and limonite. The main nickel-bearing mineral of saprolite is nickeliferrous garnierite,(Mg,Ni)6Si4O10(OH)8, and that of limonite is nickeliferrous goethite (Fe,Ni)O·OH ore (Moats & Davenport, 2014). Since the saprolite has high contents of nickel and slag formers (MgO and SiO2) and a low content of iron, it tends to be treated by a pyrometallurgical smelting process such as calcination and electric furnace techniques to produce ferronickel for use in stainless steel. In this process, the cobalt in the ferronickel does not have any economic value."

Jan 1, 2017

By A. M. Gaudin

Introduction The discovery of artificial radioactivity, that is, of radioactivity of acorns other than those which are naturally radioactive, has increased vastly the possibility of using radioactivity as an analytical cool. The incomparable value of radioactive atoms, which are commonly termed tracers, arises from the extreme sensitivity of this analytical method. To get an idea of this extreme sensitivity it may be useful co recall that gravimetric analytical methods will not permit the weighing of anything much lighter than one-hundredth of a milligram of material. Under the most favourable circumstances, this represents an uncertainty in the answer of 1016 acorns, or 10,000,000,000,000,000 acorns. Accurate spectrographic methods possibly have a sensitivity 10,000 times greater than this, but the uncertainty is still of the order of 1012 atoms. The tracer permits ascertainment of decay of a single atom so that its sensitivity, without half trying, can be several orders of magnitude greater than that of any other method available co chemists. In addition co the sensitivity of tracers to which reference has just been made, tracers have another property which makes them unique. A radioactive atom is almost exactly like the corresponding non-radioactive acorn m regard to its electronic structure, and therefore in regard to its chemical properties. The nucleus is different, but the nucleus does not participate in chemical reactions. Therefore, a tracer acorn behaves like an ordinary atom until such time as its nucleus undergoes a catastrophic decay. This unique property permits one to use tracer acorns as atomic spies and therefore to follow the behaviour of acorns of a certain kind among their own kind. In other words, the tracer method permits us to study and measure what we call self-diffusion. All of the uses of tracers that have been made depend on the two properties co which reference has been made.

Jan 1, 1949