Search Documents

By A. L. Craven, J. P. L. Bacharach, D. B. Stewart

"Inert gas use for underground mine fir e control is a well-established mature technology in some parts of the world. This paper reviews three candidate inert gases and describes three case histories where inert gas fire-fighting technology was used in actual underground fires.IntroductionInerting is the introduction of an inert gas into an atmosphere in contact with a fire to reduce the level of oxygen and hence the intensity of the fire 10 the point of extinction. The benefits of inerting include:a. Reduced Explosion HazardBy displacing oxygen from the atmosphere surrounding the fire the risk of secondary gas explosions is reduced. For example, simple methane-air mixtures at standard temperature and pressure are non-explosive below 12% oxygen. In actual mine fires, combustible gases may include hydrogen and carbon monoxide as well as methane. Such gases are also rendered non-explosive with oxygen removal to below 40/0. Fuel-rich oxygen-deficient mixtures can however be made explosive through dilution with air. Such dilution can occur downwind of the fire. It is also important to remember that the atmosphere in a sealed-off fire zone is rarely homogenous.b. Reduced Fire Intensity and SpreadIn a fire zone the initial combustion may well set alight materials surrounding the fire. Inerting can reduce the intensity and spread of secondary combustion and can cool the area surrounding the fire zone after the fire itself has been extinguished.c. Reduced Air LeakageLeakage of air into sealed areas in excess of the natural leakage may be reduced either by introducing inert gas into the leakage paths to replace air or by pressure balancing seals and providing a chamber of nitrogen on the outbye side of the seals. Both methods assist in the reduction of the intensity of combustion and hasten oxygen starvation."

Jan 1, 1986

By P. Rocque, S. Talebi

Although the measurement of blast vibration close to the blasthole is critical to the understanding of rock fragmentation mechanisms and blast damage in the rock masses, limited experience for such monitoring exists. Because much higher vibration amplitude and frequency ranges are expected in rock masses close to an explosive charge as compared to far field vibrations, different problems from those for the far field monitoring must be considered for near field blast vibration monitoring. Currently, guidelines for design of the near field blast monitoring systems do not exist. This paper describes the development of an integrated technique for vibration monitoring close to a blast hole, including selection and installation of transducers, design of a monitoring system and signal recording. A densified cement was designed for grouting accelerometers in order to match p-wave impedance between the rock and grout. The monitoring technique described has proven suitable for blast vibration monitoring within 2 m to 15 m of a blast hole having loading conditions similar to production blasts.

Jan 1, 1993

By G. R. Larocque

"The Loss Prevention Program and management style applied at Kidd Creek enabled them to maintain a 1.02/200 000 man-hours accident frequency over a 20-year period. Falconbridge Limited, Kidd Creek Division operates a major zinc, copper, silver mine, two gold mines and a metallurgical facility in Timmins, Ontario. The metallurgical site and the base metal mine are 17 miles apart and joined by their own railroad. The minesite consists of two shafts, one 3000 feet deep and the other to 5200 feet deep, as well as the necessary maintenance and service shops. The metallurgical site consists of a 14 000 STPD concentrator, a zinc refining plant, copper smelter, copper refinery, and the necessary maintenance shops. The two gold mining operations are adjacent to the metallurgical site.At the time of writing this paper the workforce consisted of some 2500 people divided between the two sites. Nine hundred and ninety-two employees are stationed at the minesite, with the remainder at the metallurgical site and gold mines. The workforce in the Timmins operation is non-unionized and reflects the belief that employee interests are well served.Beside providing competitive wages and an excellent benefit package, Kidd Creek takes special pride in its employee relations practices and continued efforts in communication.In each of the programs referred to, there have been equal involvement by both management and the employees. Each crew, under the direction of a supervisor, makes up its own health and safety committee. To maintain a successful Loss Prevention Program, it is essential that management and the employees work closely together and provide meaningful input and effort to succeed.At this point, refer to the lost time injury frequency as a measure of failure and refer to the opposite end of the scale as the measure of success. The ultimate goal of every operating company is to have a zero frequency, therefore denoting 100070 success. The company uses most of the tangible safety aids found in other mining operations, such as safety posters, safety reminders, check lists, and the use of the Neil George Safety System. The difference is the manner and style of management at the Kidd Creek Division. Their ""open door"" policy and the close association, between management and the employees, has always served them well. Also, at Kidd Creek they believe they have a well-trained and dedicated workforce."

Jan 1, 1989

By R. W. Zeindler, D. A. Fawcett

"A summary is presented of the report completed by the Coal Mining Research Centre in 1980. This report was of a cross-pit conveyor system applied as an auxiliary mining complement to the major stripping unit, a dragline. The purpose of the CMRC report was to evaluate selective mining and replacement of the upper horizons of the strata as an aid in reclamation. These strata were the topsoil, subsoil and glacial till.Past utilization of cross-pit conveyor systems and related engineering studies were assessed. The parameters of the study were based on the mining and geological conditions of the Alberta prairie coal mines. The principal excavator for stripping was a dragline. Excavation of the upper horizons was done by a bucket-wheel excavator discharging onto the crosspit conveyor. Alternative equipment applications were economically compared. Four cases or geological sections were evaluated in detail. The economics of the alternative mining systems for each of the cases were determined. In all instances, the most economical solution was a tandem system utilizing a dragline with a bucket-wheel excavator/ cross-pit conveyor system."

Jan 1, 1981

By Robert B. Parsons

"On February 15, 1984 Finance Minister Lalonde presented to Parliament a budget heavily flavoured with the current consultative mood of the Government. Notably absent from the budget was the typically long list of tax changes of immediate effect. Instead, the bulk of the budget papers consisted of a wide variety of white papers on significant topics that would have a far reaching impact on the future of all Canadians.This month. Tax Notes examines the highlights of Mr. Lalonde's budget.IntroductionThe mining industry need not feel slighted in Finance Minister Lalonde's budget of February 15, 1984: the budget offered very little that would have an immediate impact of significance on any sector of the economy. Apart from some welcome announcements for the oil and gas industry to postpone the implementation of certain negative tax changes, the budget was surprisingly scant in terms of definitive tax proposals.While massive revisions in the rules relating to pensions, small businesses, commodity taxation and profit-sharing were brought forward, many of these proposals are set out in White Papers or other documents to be implemented into legislation only after further consultation. Canadians will accordingly have to wait for such promised benefits as increased RRSP and other pension contribution limits."

Jan 1, 1984

By H. Soto, P. Lacombe, R. del Villar

"During the summer of1989, Les Mines Selbaie, with the cooperation of Université Laval initiated a research project to evaluate the column flotation technology for its concentrator near Joutel, Quebec. The experimental work involved both a 5 cm by 11 m laboratory column and a 45 cm by 10 m home-made pilot unit Amenability tests were conducted using both units on various streams of the plant. Results showed that columns are not suitable for the copper cleaning circuit because the loss of precious metals, associated with the rejected pyrite, overcome the improved copper metallurgy. On the other hand, column testing at the zinc circuit showed improved zinc selectivity.Scale-up testing was', therefore, conducted on the first zinc cleaner concentrate using the laboratory-size column. The influence of variables such as porous parger grain size, wash water flow rate, airflow rate and froth depth values on column performance was' first assessed. Scale-up parameters were then determined using the optimal operating conditions from the previous tests. Simulation facilitated the determination of the most convenient plant-scale column arrangement.A number of conclusions concerning the experimental determination of scale-up parameters are also presented."

Jan 1, 1993

By James F. Kelly

"Research and development on the production of liquid fuels from coal is rapidly expanding worldwide. AImost every industrialized country is engaged in coal liquefaction research and process development. In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas.A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described.IntroductionThe CANMET coal liquefaction program is made up of two interrelated parts. The first part consists of the research and development work being carried out at the Energy Research Laboratories near Ottawa, Ontario. The second focuses on contracted research and development as part of the Coal Conversion Program of Energy, Mines and Resources Canada. The long-term objective of the liquefaction program is to contribute to Canadian liquid fuels production through the definition, research, development and demonstration of different coal liquefaction technologies for the Canadian marketplace.In coal liquefaction, the main objective is to produce liquid hydrocarbons with a higher hydrogen-to-carbon (HIC) ratio than the coal feedstock while reducing heteroatom (S,O,N) content, removing mineral matter and minimizing gas production. Typical atomic HIC ratios for a variety of Canadian fossil fuels are shown in Figure I. Canadian coals have about 500/0 of the HIC ratio present in tar sand bitumens and heavy oils and only about 20% of the ratio available in methane. In general, the cost of synthetic fuels production is related to the cost of hydrogen and, therefore, to the increase of HIC ratio between feedstock and products. On this basis, the production of liquid fuels from coal would be expected to be more costly than liquid fuels produced from bitumens and heavy oils. However, for mined tar sands and some heavy oils this difference tends to be offset by the large sand content (>90 mass %) of tar sand bitumens and the increased production costs of viscous heavy oils. For example, it can easily be shown that for equal weights of distillate <525°C) yield, current coal liquefaction processes required between two and three times less mined coal by weight than the mined tar sand s required for the most technically advanced processes proposed for bitumen upgrading."

Jan 1, 1981

By E. O. Reinbold, J. H. Johnson, D. E. Keski-Hynnila

A field laboratory for use in monitoring underground mine air quality has been developed and proven in underground service. The laboratory includes two separate monitoring systems and data analysis computer programs. One is the Mine Air Monitoring Laboratory (MAML). This is an enclosed trailer-mounted laboratory capable of monitoring CO2, CO, NO, NO2 particulate matter, S02, NH3, temperature and air velocity in the mine drift. The MAML can be up to 1000 feet away from the area being monitored. The second system is the vehicle data system, mounted on the load-haul-dump (LHD) vehicle, which monitors engine speed, engine fuel rack position, exhaust gas temperature, ambient temperature, vehicle speed, CO2 concentration near the operators&apos; breathing zone and the mode of operation of the vehicle. The two computer data analysis programs and the two field instrument systems comprise a complete Mine Air Quality Laboratory (MAQL) for underground pollutant studies. Data from the systems have been used for studying vehicle duty cycles, ventilation systems, exhaust after-treatment devices, vehicle exhaust system design and portable instrumentation. Descriptions of the laboratory are presented along with a summary of some of the experiments performed. The capabilities of the lab are discussed, along with future potential uses.

Jan 1, 1981

By R. A. Sproule

Abitibi Greenstone Belt ? ~2.745 to 2.680 Ga (U-Pb zircon ages) ? Several lithologically-distinct and structurally repeated(?) assemblages ? Represents: ? Allochthonous terranes? ? Single autochthonous terrane? ? Combination of the above Volcanology of Komatiites in the Abitibi greenstone belt ? Tisdale and Kidd-Munro assemblages have channelized flows ? Pacaud and Stoughton-Roquemaure assemblages DO NOT have channelized flows ? Only Tisdale and Kidd-Munro assemblages are mineralized

May 1, 2003

By Owsiacki. Leo

Both the 8 and A-C ore zones of the Heath Steele Mine contain extensive areas of brecciated ore. This texturally distinct ore type has been tentatively defined as a fragmental or conglomerate massive sulphide. It consists of subangular and round fragments of pyrite up to 30 em in diameter, smaller quartz clasts and chloritized, mineralized, lithic fragments in a faintly banded matrix of pyrrhotite and chalcopyrite. The chalcopyrite is concentrated in the pressure shadows of the fragments and appears to reflect remobilization and recrystallization during a deformation which postdates the formation of the clasts. A generally conformable relationship with the underlying banded pyrite-sphalerite ore, discordancy with the host banded argillites, spatial distribution and similarity to Kuroko ores suggest that the fragmental ore is of primary origin and that breccia formation is probably due to soft-sediment slumping or sliding initiated by volcanic explosions, as hypothesized for similar massive sulphides in various Japanese mines. It is nevertheless recognized that certain structural features in some clasts may result from deformation preceding the formation of the breccia, and at this stage a tectonic origin cannot be completely eliminated.

Jan 1, 1979

By V. J. Hucka, J. H. Tu

"A computer model has been developed for evaluating the performance of truck and shovel operations in an open-pit mine. The data required for describing the haulage network are simplified and shift startup and ending procedures specific to any given mine can be incorporated into the model readily . The model uses a FORTRAN-based simulation language SLAM and can be tailored to the conditions and practices of a particular mine.The model is used to analyze truck and shovel operations, evaluate different haulage layouts in the planning stage, or compare the expected performance of alternative truck dispatching systems.Stochastic simulation is used to model the random variation in time required f or the individual activities. This gives a more realistic representation of the processes under study. Simulation runs show good agreement with actual performance. The model is especially useful for examining alternatives in equipment acquisition , haulroad design, truck-shovel allocation and dispatching methods. The results of such simulations provide a sound basis f or making major management decisions.IntroductionTruck haul age is widely used in open-pit mining operations. It is also the largest cost item in the operating costs of an openpit mine, in some cases accounting for an estimated 50% of operating costs(1) , Truck replacements, which are necessary from time to time, involve large amounts of cap ital. Increasing depth of mining and consequent increase in stripping ratios require additional capital investment in the truck-shovel fleet. The sharp rise in energy costs over the last decade has also contibuted significantly to an increase in truck fleet operating costs . All these factors have led mine operators to search for ways to improve the effectiveness of the truck-shovel fleet, in order to lower costs and maintain a profitable operation in the face of declining markets and increasing world wide competition.Control of truck haulage in an open-pit mine is usually done in one of two ways."

Jan 1, 1985

By Christopher Andreae

"Years before the present iron and steel works were established at Sydney, several thriving although short-lived iron work s operated in Nova Scotia. These furnaces reflected the general nineteenth-century North American experience with iron work s. At the beginning of the century, small furnaces struggled to supply local needs. Charcoal was the principle fuel and water powered most furnace equipment. By the end of the century, a few huge primary iron and steel work s dominated production for Nova Scotia and the rest of Canada.Two sites achieved prominence in the nineteenth-century Nova Scotia iron industry: Londonderry and Ferrona. Londonderry, the larger and longer-lasting of the two sites, is today a small village on the south flank of the Cobequid Mountains, about 30 km west of Truro. Prior to the establishment of an iron works in 1849, no community existed. At the peak of operation in the 1880s, however, over 2,600 people were located there. The second site, Ferrona, today is a mere crossroads on the map, about 10 km south of New Glasgow. Following the construction of a blast furnace there in 1892, a small village grew up around the furnace, but once the furnace was blown out in 1904, the population gradually drifted away.Early HistoryThe history of Nova Scotia&apos;s iron industry began in 1604 when Samuel Champlain became the first European to identify iron ore in the future province. Despite this early acknowledgment, iron was not smelted commercially in Nova Scotia for another two hundred years. Although primitive smelters of the period produced more iron than could be used locally, early settlers depended on imports of iron from Britain and the United States."

Jan 1, 1983

By J. B. Hinzer, J. D. Harvey

"Noranda&apos;s Lyon Lake property in the Sturgeon Lake area of Northwestern Ontario was staked by Mattagami Lake Mines Limited in May 1969 to cover airborne Input anomalies. Subsequent ground geophysical and diamond drilling programs resulted in the disco very of the Boundary Extension, Lake and Creek ore zones. As of December 31, 1978, ore reserves were estimated at 3,945,000 tons assaying 6.53 per cent Zn, 1.24 per cent Cu, 0.63 per cent Pb, 3.42 oz/ton Ag and 0.010 oz/ton Au.These deposits are hosted within the South Sturgeon Lake volcanic pile of Archean age, which consists of several cycles of basic intermediate and felsic volcanic materials overlain by a sedimentary iron formation and built upon a plutonic base (Franklin , &apos; 1975). The top 50 m of the second felsic cycle, according to mine terminolo gy, contains the mineralization within Quartzphenocryst- bearing felsic lapilli tuff and underlying thin discontinuous graphitic sediments and altered coarse pyroclastics. The basal andesitic member of the overlying cycle forms the hanging wall to the ore deposits.Although there is no alteration pipe below the deposits, the coarse footwall rocks are permeated by chlorite, garnet, carbonate, iron sulphide and magnetitie-bearing veins intensifying from west to east.Immediate host rocks are alkali depleted and MnO, FeO, Zn and Cu enriched compared to Goodwin&apos;s (1972) average Archean rhyolites. Bedded pyrite-pyrrhotite-chalcopyrite lenses with sphalerite-rich tops are underlain by weakly developed stringer mineralization.Traversing eastward from the Lake Zone to the Creek Zone and toward the Sturgeon Lake Mine deposit, more rapid facies changes, more pronounced chloritic and carbonate alteration, the presence ofgarnets, greater MnO, FeO, CaO and Ag abundances, and increasing Zn/Cu and MnO/FeO ratios are apparent."

Jan 1, 1981

By Michel Lefebvre, André Piché

Every organization performing R&D is faced with the challenge of introducing new technologies to its operations. Difficulties must be overcome if companies are to realize the benefits anticipated from such developments. This paper outlines the difficulties encountered in transferring to operations various technologies developed at the Mining and Exploration Division of the Noranda Technology Centre. The approach used in the selection of a privileged partner for the technology transfer, the criteria motivating the choice and the process followed to establish the partnership are presented.

Jan 1, 1997

By J. B. Mitchell

Many of the pre-production and plant startup problems that we regard as inevitable are actually caused by poor organizational methods. Traditional methods of organization can be modified to provide clear definitions of responsibility, continuity and depth of involvement of key personnel in order to overcome these problems.

Jan 1, 1966

By E. Kouame, M. D. Everell, D. Hodouin, T. Kasongo

"To properly operate a mineral beneficiation plant it is often necessary to have systematic evaluations of the performances of a piece of machinery, of one of the processes or of the plant as a whole. The state of a process can be described from a collection of data: flow-rate values, particle-size distributions and chemical compositions of the various streams of the circuit studied.However, the obtained raw data are generally redundant and inconsistent from a material balance viewpoint, due to natural disturbances, sampling errors, unreliable instrument readouts and laboratory analysis inaccuracies.BILMAT is a computer program which upgrades mineral processing data, adjusting them in a least-squares sense in order that they may verify material conservation constraints. As a consequence, the program is able to calculate the best values of unmeasured flow rates (such as. circulating load ratios). BILMAT is a very general program in the sense that it can accept various data from any type of mineral processing circuit, and its usefulness is demonstrated here for three processing circuits of a pyrochlore concentration plant: grinding, desliming and flotation.IntroductionComputation of the material balance around any metallurgical process, that is the determination of stream flow rates and composition. is a basic step in its evaluation. In spite of the simplicity of the physical laws of mass conservation. and of the very fundamental need to know the flow of components around a process. it appears, particularly in mineral processing. that material balancing is quite often a difficult task. The reasons for this involve the problems associated with collecting measurements in mineral dressing plants. They are generally poorly instrumented and invariably data must be collected through hand sampling. Due to the heterogeneous nature of the streams, segregation occurs and samples are often not adequately representative, a problem made worse by the lack of circuit sampling facilities, which are often completely ignored by plant designers. Furthermore, the nature of the measurements to be performed (for instance particle size distributions in the fine range) frequently gives inaccurate results."

Jan 1, 1981

By P. R. A. Andrews, R. K. Collings

"There are more than 300 occurrences of fluorite in Canada. Deposits of economic significance, however, are confined to Newfoundland and Nova Scotia in eastern Canada, Ontario in central Canada, and British Columbia in western Canada. Fluorite has been mined and processed intermittently in Ontario and Newfoundland until November 1990, when Canada&apos;s only producer Minworth Ltd., a U.K. based company, with a mine and concentrator near St. Lawrence on the Burin Peninsula, Newfoundland, closed its operation.CANMET has processed ore samples from each of the major mineralized areas, and thirty-one studies were conducted between 1920and 1970. A summary of the important aspects of the various testwork studies is presented. The production of acid-grade fluorite was possible by flotation, and ceramic-grade, by flotation and gravity concentration methods. Gravity concentration methods included heavy media separation, jigging and tabling. Flotation was by direct and reverse techniques; associated minerals, quartz, calcite, barite, etc. were depressed by a variety of depressants. The function of the major depressants is discussed briefly. The various uses offluorite which include hydrofluoric acid, chlorofluorocarbons, aluminum production, petroleum alkylation, fluxing and ceramic applications etc. are discussed briefly."

Jan 1, 1993

By Hoeve. J.

"In the unconformity-type uranium deposit at Midwest Lake, mineralization is associated with extensive host rock alteration, which affects the metamorphic basement as well as the overlying Athabasca Group sandstones. Host rock alteration is manifested by (I) transformation of clay minerals [kaolinite into illite and chlorite (sudoile)]; (2) bleaching due to removal of hematite from the lateritic paleoweathering profile and the overlying red bed, Athabasca Group sandstones; (3) loss of coherence of the sandstone resulting from corrosion of quartz cement; and (4) in the immediate vicinity of high-grade ore, development of a clay envelope due to residual enrichment of clay minerals caused by massive dissolution of quartz. Clay mineral transformation and bleaching are the most prominent and the most widespread alteration effects, forming haloes that extend for several kilometres along the strike of the mineralized structure and also constitute distinct alteration pipes that rise f or several hundred metres above the unconformity to be truncated at the present top of the bedrock.Although the two haloes are largely congruent features, cross-culling relationship s indicate that clay mineral alteration represents an earlier phase in the history of the deposit than the large-scale bleaching that gave rise to the superimposed bleaching halo.Because clay mineral alteration and bleaching are intimately tied to the mineralization and extend well beyond the limits of the actual orebodies, host rock alteration may be used as an ore guide in exploration and drill-hole evaluation. In this application a third hydrothermal discharge centre was identified, as yet untested for are, which is located between the hydrothermal centres associated with the two known orebodies of the deposit.It is estimated that host rock alteration may enlarge a potential drill-target by a factor 10 - 20X. Information on the configuration of bleaching haloes can be obtained from systematic core logging, whereas diagnostic clay mineral alteration is readily identified by means of automated, quantitative XRD techniques."

Jan 1, 1984

By A. B. Irwin

"Discussion at MeetingDR. D. DERRY (Ventures Limited) referring to the diagram (Figure 15) which shows a transverse structure section across the Central Slocan area, asked what the assumed structure at depth was, remarking that dips are steeper and more uniform at depth and that the contortions with gently-dipping axial planes are at higher elevations. He wondered whether the section represented ,part of a very large fold with steeply-dipping axial plane.MR. J. D. LITTLE (Canadian Exploration, Limited) replied that E. B. Mayo (Kelowna Exploration Company) and others had considered that the entire section illustrated faces to the southwest and represents part of the lower limb of a great overturned •syncline which is concave toward the southwest.DR. R. DEWIT (Geological Survey) remarked that the photograph of a ripple mark (Figure 7) showed internal lamination conformable to the ripple mark and wondered if the structure was not due to slumping during consolidation, since the normal mode of formation of ripple mark would seem to preclude the possibility of such internal stratification.MR. LITTLE remarked that in his opinion such structures should not be depended upon alone with-out other confirmatory evidence of the direction of tops of beds."

Jan 1, 1952

By Carl Edmunds

Talk Outline Deposit?s Vital Statistics and Economic Environment Regional Geologic Setting Deposit Geology UBC Research Search Model and Current Exploration Plans Kemess Operations Kemess South Mine Mining rate (2006) ?135,000 tonnes / day Mill throughput (2006) ?52,000 tonnes / day Average Annual Production ?300,000 oz gold and 75 million lbs copper ?Production until mid-2009 Kemess North > Open pit reserve 423.8 million tonnes @ 0.3 g/tgold and 0.18% copper > 4.1 million ounce gold reserve (127 tonnes) > 1.45 billion pound copper reserve (636,000 tonnes) > 0.75:1 Strip Ratio

May 1, 2006